Support of NOR-DNET for LabVIEW 2013

Similar Questions

• NOR-DAQmx for LabView 2010 SP1

  I am looking for the installation of NOR-DAQmx for LabView 2010 64 bit SP1 package?

  Yes.  Do not change the destination directory.  The drivers will be add support for any version of LabVIEW, you installed from LabVIEW 2010.  This includes 32-bit and 64-bit versions.

• Why the basis of NOR-DAQmx for LabVIEW options are grayed out using a custom installation (with Action: Skip)?

  I try to install NOR-DAQmx Base 3.7.0 LabVIEW 2013 (LV is installed). When I try to install Standard, it does not settle for LabVIEW (only the tools common and C and USB), but gives a successful installation message.

  

  When I try to custom installation, all the "...". for LabVIEW 20XX"options are unchecked, dimmed and Action says 'Skip '.

  

  I try this on a 2011 MacBook Air 11 '' running OS 10.9. LabVIEW works very well.

  Thanks for your suggestions.

  Hello

  DAQmx Base gray if poster LabVIEW Installer is not detected on the LabVIEW support system. Did you install LabVIEW and then move it to another location?

  The LV location controls DAQmx Base is...

  / Applications / National Instruments/LabVIEW LabVIEW.app

  Thank you

  Steven T.

• Support of NI CompactRIO for LabVIEW 2015 missing

  Hello

  I have one NOR cRIO 9038 I want to use for a project, but I continue to have problems with incompatible software. I downloaded the two 64-bit LabVIEW, CompactRIO 15, FPGA Xilinx tools, FPGA Module OR and then 32-bit LabVIEW. All these components are updated in the Service Manager OR.

  I am trying to learn to use this device, and I am going through the guide of http://www.ni.com/compactriodevguide/ where the first example is a Turbine including different screws when you open the files it succesfully scans and all the screws under loads, but only at the opening, I get the following error message

  

  Here is a view of the software installed in my MAX

  

  Looking for 'The NI CompactRIO for LabVIEW 2015 drivers Support' brings me to this page http://www.ni.com/download/ni-rio-15.0/5363/en/ which I already downloaded and installed.

  How can I solve this problem?

  Thank you

  EDIT: also miss me cRIO sample projects referenced by the guides NOR as a good starting point for any new application. They must be visible when I want to open a new model/sample. Is a further indication that I'm missing something - or should try to reinstall? Simply, I can't understand what it is that I might be missing.

  You also have LabVIEW Real-time and LabVIEW FPGA installed? You probably need to install those before the CompactRIO drivers. I don't know if LabVIEW RT/FPGA is supported in LV 64-bit - it does not look like it does in LV 64-bit in your screenshot MAX.

  Edit: Sometimes the installation order can be important - LabVIEW/FPGA/RT first and then the CompactRIO drivers - you might want to do a reinstall and see if that sorts it.

• Taken autoCad supported graphics card NVIDIA for AUTOCAD 2013

  We are a company of IT support with a customer who has an elite of HP 8200 with an Intel Core i7 processor, 8 GB of RAM, a 1 TB drive and requires to run AutoCAD 2013. We are struggling to find a graphics card that is supported on the 8200 elite, please see below for a list of support NVIDIA graphics cards, could you please tell if none of those of list would work on a 8200? Ideally do not really want to spend more for £150-£200.

  http://USA.Autodesk.com/ADSK/servlet/SYSCERT?siteid=123112&ID=18844534&results=1&sType=graphic&Produ...

  I look forward to hear from you.

  Matt

  I guess it will work, but it is not certified by Autodesk...

• I don't see the icon of NOR-DAQmx in measurement window in Labview 2013 (student Edition)

  Hi all:

  I installed the driver NOR-DAQmx and Labview 2013 (Student Edition). I connected an acquisition of data NI USB-6008 and tested using NOR-DAQmx and that it works correctly.

  Now, I tried to make registration of data of this device using the software Labview installed but as I open a new project and go to the block diagram and show the measure menu I can't NEITHER-DAQmx icon in the window (Menu) measurement in Labview 2013 (student Edition).

  Any suggestion?

  I enclose two screenshots.

  Help, please.

  Thank you

  In what order did you install software?

  You must install LabVIEW first, followed by DeviceDrivers!

• cDAQ works correctly with Labview 2013?

  I have already upgraded to the LV805 for Labview 2013 in an existing system that has the cDaq-9172, NI9205, NI9263, and NI 9403.

  When executing NI MAX, it detects that cDAQ 9172 (chassis), but none of the cDAQ modules are detected.

  When I open my application, the paths of the cDAQ doesn't appear in entry options, so when it works, and the error message.

  I have SP1 2013 LV f2 and NEITHER-DAQmx 9.8

  This is a known issue, or I have a configuration problem?

  Help, please

  EDGAR_PLATRONICS wrote:

  Now, I have another problem.

  When I turn on my PC cDAQ does not start automatically.

  I have to go to services Windows and manually start OR Setup manager. Same startup is set to Automatic

  Once I run it, cDAQ works correctly.

  My company uses McAffe antivirus

  Concerning

  Edgar

  Mine also.  (McAffe)

  It turns out than if you change the startup type to "Automatic (delayed services start)" service OR McAffe plays more enjoyable.

  

• [LabVIEW 2013] Update Service NOR recommend to install the update for the 2012 LabVIEW runtime engine

  Update service NOR recommend to install the patch f5 for the 2012 LabVIEW runtime engine. However, I have LabVIEW 2013 currently running on this computer and never had installed LabVIEW 2012.

  Is this expected behavior and it is actually recommended to install this update?

  Hi mest,.

  Details of the full patch for f5 patch are available in this knowledge base article. As a general statement, we encourage everyone to install the patches as soon as they are available through the Update Service, especially if they are marked as Urgent (it is not marked urgent). In this particular case, it is unlikely that you'll turn to all the problems solved by the f5 2012 SP1 hotfix since you use LabVIEW 2013.

  The reason why you see the update in the update service is LabVIEW 2013 installs several versions of the runtime LabVIEW, so Update Service sees that you have on 2012 Run-Time Engine installed and invites you to patch.

  Kind regards

  Jeff Peacock

  Product Support Engineer | LabVIEW R & D | National Instruments

• NOR-Fieldpoint supported in Windows 7 and LabView 8.6

  We have a 'classic' with an ethernet controller FieldPoint system. We want to be able to read/write from/to the FieldPoint network using a computer with LabView 8.6 and Windows 7. NOR-FieldPoint is supported in LabView 8.6 and Windows 7?

  Kind regards

  Nate

  Hi natewkidd,

  I feel like some confusion between the operating systems running on a development computer (as Windows 7) and real-time operating systems that run on our real time (such as the PS-2000) controllers. I will do my best to clear up this confusion first answering your questions.

  (1) what is the difference between 2009 LabView real-time and LabView 2009?

  LabVIEW Real-time 2009 is actually a software officially known as 2009 LabVIEW Real-time which is installed after the LabVIEW 2009 development software to allow the user to develop and deploy applications in real time on targets in real time as your PS-2000. You can consider the LabVIEW Real-time 2009 almost as a plug-in for LabVIEW 2009 deployment and development of real-time applications.

  (2) if I have a PS-2000 on the ethernet network and to use a computer that is running Windows 7 and LabView 2009 for record and display data, will I still be able to communicate with the network FieldPoint screws write FieldPoint to my Windows 7 computer?

  If you go just to use the PS-2000 as a network module (NOT to deploy a real-time application to run on the PS 2000 itself), you should be able to communicate with him using just the read/write FieldPoint screw on your Windows 7 with LabVIEW 2009 machine and the driver NOR-FieldPoint 6.0.5. In this case, you actually do not need the Module Time since you do not deploy the application to the target in real time.

  About the PS-2000 unsupported beyond LabVIEW 8.5.1, is because the controller's memory is not large enough to hold the software that is installed on the controller with LabVIEW 8.6.x Module real-time and LabVIEW Real-time Module 2009. For more information on this, you can check this knowledge base article.

  I hope it's useful! Let me know if you have any other questions.

  Thanks for choosing National instruments.

  Aaron Peña

  National Instruments

  Technical sales engineer

  http://www.NI.com/support

• LabVIEW 2013 64 bit does not support the 'toolboxes connection database?

  Hello

  I have download the labview 2013 64 bit & registed with success

  But encount a problem when I try to install "2013DCT"(database connectivity toolkits)

  Don't LV2013 64 bit does not support this toolkit?

  If Yes, where can I find the boxes to tools for 64-bit?

  You can install the version 32 bits in a relavent LV and copy the installation.
  /Y

• NOR-DAQmx 9.2.2 for 6251 USB works for labview 8.2?

  Driver download OR-DAQmx 9.2.2 USB 6251 work for labview 8.2?

  Thanks in advance

  NOR-DAQmx 9.1.1 was the last version to officially support LabVIEW 8.2

  NIquist: I'm a student as to why this KB seems to have disappeared in the air.  I can see inside, but not outside.  I'll update the post you linked when I tell me what's wrong.

• Problem setting Legacy DAQ board using NOR-DAQ 6.1 for Labview

  I know that the Board of Directors is an old legacy product not supported by NEITHER, however for a low-budget project, I have 3 of these AT-MIO-16 x cards and the need to use them.

  I know I got this job in the past not distant os, however, for the life of me can't get things sorted and work.

  You use a NT box, in which this configuration used to work... uninstalled and started fees for other reasons, and I can not get the NOR-DAQ 6.1 to support LAbview 6.1 or 7.1.

  Of course, I understand the OR-DAQ 6.1 should be used for Labview 5 and older, but also know this has been successfully done in the past.

  I downloaded all knowledge base articles dozed or both support and remember to use successfully the last time that I set up so I know not somehow it works.

  My configuration is: AT-MIO-16 X to the bus combo board (called work)

  NT PC

  LabVIEW 6.1 or 7.1

  NOR-DAQ 6.1 is the most recent to support this card.

  However, it will not install its support to its latest versions of Labview and I get errors, crashing, or missing files, when I followed various circumvention of knowledge base solutions.

  I was hoping that someone has a documentation somewhere how to handle this, because it really is a matrix of spaghetti.

  I can get NOR-DAQ support files installed, and Configuration Manager works well, finds the map and allows its parameters to be defined.

  But when I load the DAQ vi of any type, Labview accidents and the wizard of data acquisition channel does not work at all (no error).

  Thank you

  Yes, the installation program from the folder of disks for NOR-DAQ 6.1 on the ftp site has worked well.

  Workaround. Thank you

• Support for LabVIEW 2016

  Can someone tell me what VirtualBench drivers will be available for LabVIEW 2016?

  Release date is... right now! NOR-VirtualBench 16.0, with the help of LabVIEW 2016, is available here:

  • Driver 16.0.0 and NOR-VirtualBench Application

  (My apologies for yesterday, does not but it takes a little while to download pages to go live.)

• What type of support for labview usb protocols?

  Hello guys I want to connect a device to your pc via a usb port and I want to use labview to analyze the data.

  But first of all, I would like to know what usb protocols support for labview.

  USB, USB CDC and other TMC?

  I ve read labview recognizes a raw device to the usb, but what is? Is it VI to read and send data, or I have to do? If these VI exists, they do the handshake? flow control?

  Thank you.

  Please read the chips and have a look at the USB specification (it is linked to in the nuggets).

  TMC, CDC, MAss Storage are all built on the basic USB protocols.

  LabVIEW has no built-in support for one of these classes of devices except Test and measurement.

  Shane

• support for labview 2014 nidaqmx

  Looks like the last 9.9 niDAQmx is not support for Labview 2014. Any idea on where to download / expected eta for niDAQMX support for labview 2014?

  A new version of LabVIEW is generally released during the week OR (starting tomorrow). I guess, at the end of this week, at the latest, you will find all necessary drivers - including a new pilot DAQmx - ni.com.

  Kind regards, Jens