Surface RT - default configuration Windows updates to returning date change

Similar Questions

• Default configuration Windows update restore changes do not turn off your computer.

  I'm running 64-bit Windows 8

  Guard saying default configuration of folds by using Windows Update

  Hi Cris,

  Thanks for posting your query in Microsoft Community.

  You did it any significant hardware or change software on the computer before this problem?

  I understand that you can not install some updates with the error message "failure of configuration of the Windows updates...". ». I can imagine the disadvantages suffered by you and will certainly help you in the right direction to solve the problem.

  First place, according to the error message, I suggest you to try the steps in the following article and check if it helps.

  "Configuration of the Windows updates failed. Restoration of the changes. Do not turn off your computer"error when you try to install Windows updates

  Note: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  
  

  The question may arise if the Windows downloaded update packages are corrupt. So, if you are able to start the computer successfully after following article provided above, I also suggest you try the following steps and check if the problem persists.

  Method 1:

  Try to run that Windows update utility provided in the following link.

  Problems with installing updates

  Try to install the updates after running the troubleshooter.

  If the problem persists, try the following method.

  Method 2:

  I suggest you to use Deployment Image Servicing and Management to fix Windows Update errors.

  (a) open an elevated command prompt. To do this, press the Windows key + Q and type in CMD right click on command prompt in the list and select run as administrator. If you are prompted for an administrator password or a confirmation, type the password, or click allow.

  (b) type the following commands. Press enter after each command

  • DISM.exe / Online/Cleanup-image /Scanhealth
  • DISM.exe / Online/Cleanup-image /Restorehealth

  (c) close the command prompt, and then run Windows Update again.

  Check if the problem persists.

  Hope this information is useful. Let us know if you need more help, we will be happy to help you.

• My Dell Latitude Tablet is stuck on 'Failure to configure Windows updates from reinstatement of changes' (Windows 8)

  It was stuck on this during about 3 hours and I desperately need to use... It is essentially new from today, as I had mail. I really don't understand why this is happening and I can't find a way to fix.

  From what Ive seen in similar forums, that I'll post things that do not work in my situation.

  • I don't have any sort of keyboard or mouse for this tablet.
  • I tried to restart the flight button and button / stop
  • I took the battery.
  • I do not have a more 8 GB USB so I can't use a recovery.

  Honestly, I'm so frustrated because I both want and need to use it for school... I don't have the time and money to run around to try to find a larger USB... at least not for a few days or a week. If no indication as to what is wrong and all the other options would be very appreciated.

  Hi Alex,

  I understand the inconvenience caused to you due to this problem. Installation of Windows Update takes this long period. It seems to be a problem with the Windows Update components. You could also face this problem at any time update does not install correctly and it is not to let any other updates to settle.

  As you mentioned that this is a new feature by Dell I suggest you contact the manufacturer or point of purchase. You can contact the Dell forums on the information provided below.

  Mobile devices

  http://en.community.Dell.com/support-forums/mobile-devices/f

  Let us know the status of the issue.

• Error Windows Updates 'configuration of Windows updates fail, returning of the changes.

  Updates to the title: original Windows.

  That means 'configuration of the Windows updates fail, returning from changes '? My laptop has been updated but got stuck on 12%, and would not go further. It is restarted 3 times and only went up to 12%.

  Was actually able to solve this problem through more research. It turns out that his receiver of wireless mouse and a SD card was stalled the installation program. I don't know why but I turned off the machine (long press the button), remove, checked all other ports, block tire and cord then put back the battery and card, turned on and it ran through the installer without problem.

• After refreshing the computer, when it is about to finish the update that went FAILURE CONFIGURATION WINDOWS UPDATES

  Hello... I just UPDATE my computer and then when I started to update, when he is about to complete the update this showd upward

  DEFAULT CONFIGURATION WINDOWS updates what to do about it... my OS is windows 8

  Original title: I update my computer

  Error: Failed to setup of the Windows updates. Restoration of the changes. Do not turn off your computer when you try to install Windows updates
  http://support.Microsoft.com/kb/949358

• Failed to update Windows 8 (KB2756872, KB2768703), happens to 30% then get error "failure Configuring Windows updated. Changes in return ".

  I installed 2 updates.

  I installed both of them using the standalone installer which.
  First, I checked the updates using Windows updates and then installer of stand-alone download from the link more information if I can use this update later.

  Here are the 2 updates I try to install:
  1 Windows8-RT-KB2756872 - x 64
  2 Windows8-RT-KB2768703 - x 64

  I rebooted my system after installing the updates.
  Windows configures updates up to about 30% and the system gets stopped and restarted.
  Then he went it 100% and all of a sudden, I got a message something like:
  "Failure of Windows updated. Changes in return ".
  It is just returned

  Here are all the logs files (CBS.log, WindowsUpdate.log, WindowsUpdate (1) .log)
  http://bobdn.com/files/logs.zip

  Please tell me how can I get the update installed successfully.

  I finally solved my problem with the update kb2756872 ("update failed, returning of changes"). It was caused by the reserved partition Windows is not set to active (I dual boot using GRUB). Go to the Control Panel-> administrative tools control->-> computer managementdisk management and make sure that the reserved partition is marked 'Active'. This also solves many other problems I experienced as not able to activate Windows startup settings.

• Update error configuration Windows Updates... Do not turn off your computer. This is immediately followed by the default configuration of the Windows updates. Restoration of the changes. Do not turn off your computer.

  OT: Windows Update failure 8.

  I recently re-installed Windows 8 using an old product key once I updated my PC using Windows 7 due to failure to boot Windows Technical Preview. The installation went smoothly, but when installation is finished, he told me that I had installed updates, for the most updated security. I installed them and restarting my PC, he has said configuration Windows Updates... Do not turn off your computer. It is immediately followed by updates default Windows configuration . Restoration of the changes. Do not turn off your computer. It accomplishes this task for like 10-15 minutes and then finally starts. Once my PC starts, this cycle starts again. So far, happened 4 times.

  Could someone please fix this? I want to update to Windows 8.1, but could end up, I'm stuck with Windows 8. (Also, why download from the store disappeared? "I'm not using a RT system).

  Thank you!

  -me15prg9926

  Why I can't update in the store?
  http://Windows.Microsoft.com/en-us/Windows-8/why-can-t-find-update-store

• Update Windows Installer KB3002885 (and later KB3000061) causes "Failure Configuring Windows Updates, changes of restoration"

  I manually ran Windows Update for about 22 updates including KB3002885 (KB3000061 is not included at this time).  It resulted in "Failure Configuring Windows Updates, changes of recovery".

  Measures taken (without the fix):

  -Reboot

  -Restart in Boot Clean with Services MS no disabled state

  -Updated Troubleshotter

  -System Restore (3 weeks)

  -DISM.exe / Online/Cleanup-image /Restorehealth

  I started installing updates a little at a time and was able to install all the updates about 22 except KB3002885, which always causes the problem 'failure configuration... '. ».

  Updates at this point (November 14, 2014) identified KB3000061.  When update was executed for this update by itself it also caused the problem of the "default configuration... '. ».

  Updates about 22 that have been installed successfully some of them were: KB3000853, KB3004150, KB3003057, KB2978121 and KB2972101.  A more complete list is available if it is useful.

  Windows 8 Pro 64 bit w / Media Center

  Norton Security Suite

  THAT IS TO SAY 10.0.9200.17148

  Worm update: 10.0.22

  Perhaps relevant: I could never update this computer Windows 8.1 in 5 or 6 attempts over a period of 6 months.  Always comes back to the previously installed Windows 8.

  Otherwise, my computer works without other unusual problems.

  Hi Brad,

  Thank you for your response.

  For problems with the upgrade to Windows 8.1, I suggest you refer to the suggestion of Madeni K N replied on 8 January 2014.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows8_1-windows_install/error-0xc1900101-0x40017-when-installing-Windows/8c893ae6-0e9b-4b7d-a647-b9065099efd6?page=1&TM=1389602587060

  For more information, you can check the link below.

  Update to Windows 8.1 of Windows 8.

  http://Windows.Microsoft.com/en-us/Windows-8/update-from-Windows-8-tutorial

  Hope this solves the problem. If the problem persists, you can write to us and we will be happy to help you further.

• I'm getting 'Failure Configuring Windows Updates, changes of restoration' by updating windows.

  It was the first time that I am trying to update my laptop of Lenovo G500s which is come with 8 windows pre installed, before installing the updates, I have restored the laptop if you default factory using Lenovo a recovery key. While the updates are being installed I received a message 'Fail configuration Windows updates reverting changes'. It lasted for an hour. When I tried to install updates again the same message appeared. My laptop came pre-installed with Nitro Pdf 8 and Mcafee Internet Security, so I have even uninstalled them, I also ran Mcafee Consumer Product Removal Tool. But the problem with windows update remained. I then ran the convenience store update Windows that sets these two problems:

  fix windows update fixed the database and repair misconfigured update windows components, but this solves nothing. Later I discovered that although the resolution of update problems show that the problems have been solved but convenience store running immediately shows again the same problems.

  So this time I ran again the recovery system, and immediately after the system recovery windows update of convenience store that showed the problems mentioned above two updates of windows.

  Is it so that means the recovery partition itself contains other problems that my problem would have been solved, what do I do to fix this?

  Take a look on: http://support.microsoft.com/kb/947821/en-us

  ... use the Deployment Image Servicing and Management (DISM) Inbox. Then, install the update or Windows service pack again...

• failure configuring windows update

  configuration windows updated sometimes twice a day, updates download scussful then restart configure up to 15% then failure, to seniors revertingback, then works fine, til reappers message every day.

  "I followed these instructions but they warn me that this updae cannot be installed in Mode without failure.  When I thought how to restart in Normal mode.

  Since then, I have not known the laptop appeared this exact error message, I'm assuming that you thought you could only install this through the normal start screen.

• Failed to configure Windows Update (update for windows 7 kb974431)

  My sytem downloads the update, then gives me "unable to configure Windows Update". Also get detaisl error code: C004f050.

  What is the problem and how to fix this?

  Thank you

  Look at similar thread:http://social.answers.microsoft.com/Forums/en-US/vistawu/thread/ff57f326-0f1d-412c-a4d0-14de1eaf0836

  try to order are sfc and reset the system

• Configuration Windows Update failure

  When I bought my PC, it is already pre-installed Windows 7 Pro and I do not have the disc with me. Usually, I keep my automatic update. last 2 days I update my IE 7 to 11. Which was the day I turn on my automatic update. Today, when I turn on my PC, I got the message "failure configuration Windows Update... "I waited for hours and it will not be the end. I try to turn it off, then restart. It came again the same screen. Even in safe mode.

  How can I cancel the update? How can I get my windows to start?

  Help, please!

  Hello

  Thanks for posting in the Microsoft Community.

  We appreciate to try few troubleshooting steps.

  I suggest you to refer to the Microsoft Help article and check if it helps to resolve the issue.

  https://support.Microsoft.com/en-us/KB/949358

  I hope this helps. Just reply to us with the State of the question.

  Thank you.

• Failure configuring windows updates current portable window7

  When Windows tries to update my computer I get the message "failure configuration Windows updates revenant changes...» "Sometimes it sucks seed for update and computer works normally, but in 10 minutes. It asks me to update windows again and if not postponed the repetitions of the cycle.  The computer is an HP with Windows 7 Home Preimum and a 64-bit operating system.

  Hello

  Please refer to this link and check if that helps.

  https://support.Microsoft.com/en-us/KB/949358

• How can I configure windows update in order to start the procedure, when I connect to the school network?

  OT:help configuration of Windows Update.

  I use windows 8, now my problem is that I have to enter a user_name and password each time you start the browser, if you close the browser, or open another browser, you must enter user password again once you use a wifi or lab computers. Now when I connect to wifi, my browser instantly request name username-password but windows update is not so. I tried this a few times, only once named windows update displays dialong box asking username and password and it takes hours to do.

  How can I configure windows update already if start update already when I connect to the school network.

  Wifi authentication which traverse the browser means that you still need to open a browser and a connection that first, before any other programs can access the network.

• Failure to configure Windows Update

  Hi rich,

  Sorry to know the steps of troubleshooting force worked for you.

  Please follow these steps and continue with the next steps to reset the Windows update components.

  Use the System File Checker tool to repair missing or corrupted system files

  http://support.Microsoft.com/kb/929833

   

  Follow the steps below to install the selective Windows Update:

  Follow these steps we will know what update is a problem and we will try to solve the problem on the basis of that.

  1. Go to control panel-> Administrative Tools-> Services and scrolled down to find the "Windows Update" service and stop it.
  2. Then restart again and go back to Windows Update, it will display all the current updates available. You must deselect all updates and select only the first two and install it, must be installed successfully (reboot required).
  3. After the reboot, chose two more and install. Then choose 5 updates and install them. That must be installed successfully (reboot required).
  4. The restart will take a long time. You can see "Configuring Windows updates" for about five minutes. After the restart, select the remaining current updates, including an update of the driver in option. They must install as well successfully (reboot required).

  Hope this helps, get back to us if you need further assistance for Windows.

  Shrinkar,

  I did those batched updates since last week. It works for most, but I've only had a left which is take back me to the "failure to configure...". ». It starts at 30% and after it configures the windows updates, but as soon we get 67% to 100% then "failed to... set back changes...". "appears again.

  BTW, this is the windows update try to configure for ages