swcth 2950 2901 router
prejudice are Sorrento ciro I finished the CCNA I bought 2901 router machines and a 2950 switch catalist I programmed devices, so that they went on the internet dialer interface ip nat dhcp for the internal network, we only what I failed to do, I have configured the switch with vLAN different and I configured the router with interface sub with dot1q Protocol for both the router to the switch (trunk), but when I try to a ping from one vLAN to another not pingano although it seems strange because when it comes to the frame of the vlan 2 pc to the router via the router sees Tambella routing ip address sends in a different VLAN, type vlan 3. He is someone who can help me thanks.
Hello
reading what you're saying, I think you have setup of a router on stick design
http://www.firewall.CX/Cisco-technical-Knowledgebase/Cisco-routers/336-c...
You can post the configs you have if it is a laboratory?
Don't I have the exact problem you cannot route between the VLANS?
Tags: Cisco Network
Similar Questions
-
I need to drill a 2901 router to recover passwords. Cisco methodology for the recovery of password on routers seriews 2900
said to remove the compact flash card and restart in RMON. There is no external flash on a 2901 memory card. Is there a
Compact flash card inside the box? Or you can use the old method of restart and then hit CTRL + break to begin RMON?
Thank you
Howard Davis
CCNP
There is no external compact flash card on a 2901.
Yes it is. It is hidden under a blanket of dust at the back (opposite side of the socket).
There should be slots TWO cf. Pop just the '0 '.
-
2901 router as an SSL VPN using
Hello world!
I was wondering if someone could give me a hand on this. I'm trying to use a Cisco 2901 to allow remote workers to access resources on the local network using the Client AnyConnect Secure Mobility Client. I just read this doco
http://www.Cisco.com/c/en/us/support/docs/routers/3800-series-integrated...
But it seems it does not support the 2901 platforms. I quote:
WebVPN or VPN SSL technology relies on these router IOS platforms:
870, 1811, 1841, 2801, 2811, 2821, no. 2851
3725, 3745, 3825, 3845, 7200 and 7301
Is that all just because this topic is old?
Before I have to spend money on the wrong license, I decided to give it a go (above the following article). So, when I went to
' Configure > Security > VPN > SSL VPN > SSL VPN Manager "CCP says I need license"(securityk9). I then followed the link "activate license" and clicked on the tab 'evaluation licenses. But where there are two that seems good:
- securityk9 (the CCP one says it needs)
- SSL_VPN (one who seems reasonable as AnyConnect uses SSL VPN, right?)
What is the license of right? Anyone can enlighten us please?
Also, is there any resource that explains better than all the options and how to configure the AnyConnect on a router ISR2, using CLI?
Thanks in advance
Alvaro
Hello Alvaro,
What IOS version you are using?
Beginning in Cisco IOS version 15.0 (1) M, the SSL VPN gateway is a licensing feature sits a count on Cisco 880, 890 Cisco, Cisco 1900, Cisco 2900 and 3900 Cisco platforms. A Chair does refers to the maximum number of sessions allowed both.
For more information, go through:
http://www.Cisco.com/c/en/us/TD/docs/iOS-XML/iOS/sec_conn_sslvpn/CONFIGU...
"Please note useful posts.
-
Copy the configuration of Cisco 881 to Cisco 2901
We replace our router Cisco 881 with a Cisco 2901 router. If I backup the configuration of the 881 and restore it on the 2901, will there be problems? We just want our 2901 to work the same. Thank you.
routers/switches etc. can with a base image which may allow only certain features the devices come with these out of the box so that they work.
You can buy advanced ip services images or images of advanced security that will allow all the features work. For example, you cannot use BGP or ACB unless you have an advanced picture, but you can be allowed to use RIP and EIGRP stub.
You can check what is running on your 881 with a license to show what it will tell you what is on
-
Which router to <; 10 users?
Hi all
I was wondering what would be the best IOS router for remote sites with fewer than 10 users?
Our remote sites need to connect to the central site 1 (star topology +) and at the moment we have about 4 remote sites. Most sites use Comcast Business Service (up to 50down/10up). We do not want to use the SAA, we would rather routers with integrated services.
We want to connect all via the L2L IPSEC Tunnels and all spoke to communicate fully, but also with the VPN Clients. Our current Hub is a dry ASA5505 +, but we can be out in the near future for a Cisco 2901 router. We are looking for rock solid reliability, so if it's never going to the internet, the VPN will be arrived upward when the internet is back (a problem that we had in the past).
I need as much as possible suggestions for our routers to Remote Site, so we can look over the options for the needs of our network!
Thanks in advance!
L2TP and IPSec is bread and butter for Cisco. All you have to remember that for IPSec works, you must download the IOS that will allow encryption. Also you also have an option as to the amount of DRAM desired. It is preferable, in my view, to charge the maximum amount of DRAM to a router.
You can get the router of 1900 but this, in my view, would be an overdose.
-
Cannot access internal network so AnyConnect SSL VPN, ASA 9.1 (6)
Hello Cisco community support,
I have a lab which consists of two virtual environments connected to a 3750-G switch that is connected to a 2901 router which is connected to an ASA 5512 - X which is connected to my ISP gateway. I configured SSL VPN using AnyConnect and can establish a VPN to the ASA from the outside but once connected, I can't access internal network resources or access the internet. My information network and ASA configuration is listed below. Thank you for any assistance you can offer.
ISP network gateway: 10.1.10.0/24
ASA to the router network: 10.1.40.0/30
Pool DHCP VPN: 10.1.30.0/24
Network of the range: 10.1.20.0/24
Development network: 10.1.10.0/24
: Saved
:
: Serial number: FCH18477CPT
: Material: ASA5512, 4096 MB RAM, CPU Clarkdale 2793 MHz, 1 CPU (2 cores)
:
ASA 6,0000 Version 1
!
hostname ctcndasa01
activate bcn1WtX5vuf3YzS3 encrypted password
names of
cnd-vpn-dhcp-pool 10.1.30.1 mask - 255.255.255.0 IP local pool 10.1.30.200
!
interface GigabitEthernet0/0
nameif inside
security-level 100
IP 10.1.40.1 255.255.255.252
!
interface GigabitEthernet0/1
nameif outside
security-level 0
address IP X.X.X.237 255.255.255.248
!
interface GigabitEthernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
management only
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
!
boot system Disk0: / asa916-1-smp - k8.bin
boot system Disk0: / asa912-smp - k8.bin
passive FTP mode
permit same-security-traffic intra-interface
network of the NETWORK_OBJ_10.1.30.0_24 object
10.1.30.0 subnet 255.255.255.0
network obj_any object
network obj_10.1.40.0 object
10.1.40.0 subnet 255.255.255.0
network obj_10.1.30.0 object
10.1.30.0 subnet 255.255.255.0
outside_access_in list extended access permitted ip object NETWORK_OBJ_10.1.30.0_24 all
FREE access-list extended ip 10.1.40.0 NAT allow 255.255.255.0 10.1.30.0 255.255.255.0
access-list 101 extended allow any4 any4-answer icmp echo
access-list standard split allow 10.1.40.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
management of MTU 1500
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
ASDM image disk0: / asdm - 743.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) source obj_10.1.40.0 destination obj_10.1.40.0 static static obj_10.1.30.0 obj_10.1.30.0 non-proxy-arp-search to itinerary
NAT (inside, outside) static source any any static destination NETWORK_OBJ_10.1.30.0_24 NETWORK_OBJ_10.1.30.0_24 non-proxy-arp-search to itinerary
Access-group outside_access_in in interface outside
!
Router eigrp 1
Network 10.1.10.0 255.255.255.0
Network 10.1.20.0 255.255.255.0
Network 10.1.30.0 255.255.255.0
Network 10.1.40.0 255.255.255.252
!
Route outside 0.0.0.0 0.0.0.0 10.1.10.1 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
without activating the user identity
identity of the user by default-domain LOCAL
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.1.0 255.255.255.0 inside
http X.X.X.238 255.255.255.255 outside
No snmp server location
No snmp Server contact
Crypto ipsec pmtu aging infinite - the security association
Crypto ca trustpoint ASDM_Launcher_Access_TrustPoint_0
registration auto
full domain name no
name of the object CN = 10.1.30.254, CN = ctcndasa01
ASDM_LAUNCHER key pair
Configure CRL
trustpool crypto ca policy
string encryption ca ASDM_Launcher_Access_TrustPoint_0 certificates
certificate c902a155
308201cd 30820136 a0030201 020204c 0d06092a 864886f7 0d 010105 9 02a 15530
0500302b 31133011 06035504 03130 has 63 61736130 31311430 12060355 74636e64
0403130 31302e31 2e33302e 32353430 1e170d31 35303731 32303530 3133315a b
170d 3235 30373039 30353031 33315 has 30 2 b 311330 0403130a 11060355 6374636e
64617361 30313114 30120603 55040313 0b31302e 312e3330 2e323534 30819f30
0d06092a 864886f7 010101 05000381 8 d 0d 003081 89028181 00a47cfc 6b5f8b9e
9b106ad6 857ec34c 01028f71 d35fb7b5 6a61ea33 569fefca 3791657f eeee91f2
705ab2ea 09207c4f dfbbc18a 749b19ae d3ca8aa7 3370510b a5a96fd4 f9e06332
4355 db1a4b88 475f96a1 318f7031 40668a4d afa44384 819d fa164c05 2e586ccc
3ea59b78 5976f685 2abbdcf6 f3b448e5 30aa96a8 1ed4e178 0001300 020301 4 d d
06092a 86 01010505 00038181 0093656f 639e138e 90b69e66 b50190fc 4886f70d
42d9b4a8 11828da4 e0765d9c 52d84f8b 8e70747e e760de88 c43dc5eb 1808bd0f
fd2230c1 53f68ea1 00f3e956 97eb313e 26cc49d7 25b927b5 43d8d3fa f212fcaf
59eb8104 98e3a1d9 e05d3bcb 428cd7c6 61b530f5 fe193d15 ef8c7f08 37ad16f5
d8966b50 917a88bb f4f30d82 6f8b58ba 61
quit smoking
Telnet timeout 5
SSH stricthostkeycheck
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0
VPN-addr-assign local reuse / 360 time
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Trust ASDM_Launcher_Access_TrustPoint_0 vpnlb-ip SSL-point
SSL-trust outside ASDM_Launcher_Access_TrustPoint_0 point
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-linux-3.1.09013-k9.pkg 4
AnyConnect image disk0:/anyconnect-macosx-i386-3.1.09013-k9.pkg 5
AnyConnect image disk0:/anyconnect-win-3.1.09013-k9.pkg 6
AnyConnect enable
tunnel-group-list activate
internal GroupPolicy_cnd-vpn group policy
GroupPolicy_cnd-vpn group policy attributes
WINS server no
value of server DNS 8.8.8.8
client ssl-VPN-tunnel-Protocol
by default no
xxxx GCOh1bma8K1tKZHa username encrypted password
type tunnel-group cnd - vpn remote access
tunnel-group global cnd-vpn-attributes
address-cnd-vpn-dhcp-pool
strategy-group-by default GroupPolicy_cnd-vpn
tunnel-group cnd - vpn webvpn-attributes
activation of the alias group cnd - vpn
!
ICMP-class class-map
match default-inspection-traffic
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map icmp_policy
icmp category
inspect the icmp
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
service-policy icmp_policy outside interface
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:261228832f3b57983bcc2b4ed5a8a9d0
: end
ASDM image disk0: / asdm - 743.bin
don't allow no asdm historyCan you confirm that this is correct, your diagram shows your IP address public on ASA as 30 while you have assinged on 'outside' interface like 29?
-
CISCO2901 WITH SECURITY LICENSE PAK?
Hello friends,
Could you please help me to understand, what command do I I question to see if my 2901 router has the license of secuity? and what 12xxxxx I see in this output? Whithout license will I make a VPN for remote access?
Any comments or document will be appreciated.
Kind regards!
Hello
You can see that in the version of this router show. If you plan to use SSL based anyconnect VPN remote access you must acquire a license for the same thing.
Number of concurrent users supported SSL VPN taken by platform
Platform
Maximum number of users
Cisco UC/SR500, routers series 880 and 890
10 users
Cisco routers 1900 sets
25 registered users
1941 and 2901 Cisco routers
75 registered users
2911 and 2921 Cisco routers
100 users registered
Routers Cisco 2951
150 users registered
Routers Cisco 3900
200 users registered
Concerning
Knockaert
-
Calculation of SSL VPN license
Hello
I need to purchase licenses for my SSL VPN (AnyConnect) 2901 router, and I would like to know how it is affected.
If I buy a license 10 users, it is up to the 10 named user, or it is counted by concurrent users?
If a user connects from a laptop computer and a mobile phone at the same time, with the same username, it counted as 2 user license, or just one?
Also, AFAIK, the AnyConnect Essentials license is only available to ASA and not IOS routers. Is that still OK?
Thank you.
The number of licenses using simultaneous connections, regardless of the associated user ID.
75 connected both unique usernames or a different user connected of 75 endpoints name would be count as 75 licenses in use. Laptop more phone = 2 users if the connections are simultaneous.
The Essentials vs Premium distinction is unique to the ASA. Premium features only as a clientless SSLVPN, hostscan etc are not available based on the IOS SSL VPN
-
802.1 x intermediate switches
As you watch the 802 configuration documentation. 1 x on the switches of the Cat series; There is a statement to the effect that some switches (2940 cat by CAT 3750) may be used as intermediaries. What this really means? What is the dashboard switch itself as the intermediary between the client and the authentication server? This means IF I use the 4506 cat, I can use intermediate between the 4506 and switch to the "pass-through" customer demand of 802. 1 x for the 4506? This means no doubt that intermediate switches can be used when the edge switch on their own?
I guess from the documentation that no matter what the switch is used as the edge switch is the intermediary between the client and the authentication server.
Any enlightenment will be appreciated.
Diana
Q: is this the dashboard switch itself as the intermediary between the client and the authentication server?
R: Yes
Q: you mean if I use the 4506 cat, I can use intermediate between the 4506 and switch to the "pass-through" customer demand of 802. 1 x for the 4506?
A: not necessarily. You can directly use Cat4500 as intermediary.
Q: surely, this means that the intermediate switches can be used as the edge turn on their own?
A: no, you can use them as well as intermediate and edge.
***************************************************
For 802. 1 x, intermediate devices can be Cat4000 series, Cat3550 Cat2950 or AP wireless. In other words, they are edge devices.
The middleman here means that the device behaves like a proxy or 'intermediate' between the client device that asks for authentication of access (802.1 x) and the authentication server, for example the Cisco ACS server.
Basically, what happened is, the switch will ask the client identification information (IE name of user and password), and then transmit the information to the ACS server. ACS server will check & verify the ID and will respond with the answer of SUCCESS or FAILURE to the switch. The switch will be in turn, grant or deny access to the client, based on the information/response.
Layer2 + 802.1 x NAC, devices that can act as intermediaries are Cat6500 (depend on worm IOS) Cat4500, Cat3750, Cat3560, Cat3550, Cat2960/2970/2955/2950/2940, router series C7600, switches from Cisco Gigabit Ethernet Switch Module (CGESM).
I hope this helps. Pls rate useful message (s).
AK
-
What has replaced the vpn concentrator?
Greenhorn here, I was not to sit in this place. We have three remote sites, sister of institutions, we share an app with. Host us the app. A site has a configuration of vpn concentrator, the other two use a leased from point to point line. They each have a router that connects to a single router. They want to replace the lines leased by using a vpn. Do the digging, I see that the hubs are EOL.
So, what is used to replace the hub today? What is a solution today from leased lines? They are all poor profit. My guess is that they will say look on Ebay for a hub if the solution is too expensive.
Thanks Jim
Jim
The package of security (CISCO2901-SEC/K9 or CISCO2921-SEC/K9) is the convenient way to get the combination of the router, the software and licenses you will need. I don't think that you need something more elaborate than one of these security packages.
I think one of these would be a good choice for you. It's been a while since I looked at the details of these routers. My recollection is that the 2921 offers more power, more interfaces and a few other benefits and would be attractive to many of us. But I think I understand your needs, I believe that the 2901 router cheaper and quite adequate for you.
HTH
Rick
-
I am trying to set up a VPN between a 2901 router and 831, but I'm not having any success. When I run crypto isakmp sa, I get this:
cisco831 #sh crypto isakmp his
IPv4 Crypto ISAKMP Security Association
status of DST CBC State conn-id slot
IPv6 Crypto ISAKMP Security AssociationIt doesn't seem to be a sign of life. I can access internet ok on both routers, but the failure of attempts to ping between the routers LAN IP. I guess it's a problem of nat or access-list, but I don't know what I'm missing at this time. Here are my configs:
CISCO 2901
version 15.0
tcp KeepAlive-component snap-in service
a tcp-KeepAlive-quick service
horodateurs service debug datetime localtime
Log service timestamps uptime
encryption password service
!
host name 2901
!
boot-start-marker
boot-end-marker
!
no logging rate limit
no console logging
Select the secret XXXXXXXXXXXXXXX!
No aaa new-model
!
No ipv6 cef
no ip source route
IP cef
!
IP domain name mondomaine.fr
inspect CBAC tcp IP name
inspect the name CBAC icmp IP
inspect the name CBAC udp IP
!
Authenticated MultiLink bundle-name Panelsecret user name me XXXXXXXXXXXXXXX 5!
redundancy
!
crypto ISAKMP policy 3
BA 3des
preshared authentication
Group 2
ISAKMP crypto key address 173.x.x.x mypassword
!
Crypto ipsec transform-set esp-3des esp-sha-hmac TRANSFORMSET
!
MYVPN 10 ipsec-isakmp crypto map
the value of 173.x.x.13 peer
game of transformation-TRANSFORMSET
PFS group2 Set
match address 199
!
interface GigabitEthernet0/0
Description of the Internet
IP address 173.x.x.x 255.255.255.248
NAT outside IP
IP inspect CBAC out
IP virtual-reassembly
automatic duplex
automatic speed
card crypto MYVPN
!
!
interface GigabitEthernet0/1
Description of LAN
no ip address
automatic duplex
automatic speed
!
!
interface GigabitEthernet0/1.1
encapsulation dot1Q 2
IP 192.168.1.1 255.255.255.0
IP access-group 100 to
penetration of the IP stream
stream IP output
IP nat inside
IP virtual-reassembly
!
interface GigabitEthernet0/1.2
encapsulation dot1Q 3
IP 192.168.2.1 255.255.255.0
IP access-group 101 in
penetration of the IP stream
IP nat inside
IP virtual-reassembly
!
no ip forward-Protocol nd
!
IP http server
IP http secure server
IP flow-export GigabitEthernet0/1.1 source
IP flow-export version 5
flow IP 192.168.1.5 export destination 9996
!
overload of IP nat inside source list NAT interface GigabitEthernet0/0
IP route 0.0.0.0 0.0.0.0 173.x.x.x
!
NAT extended IP access list
ip permit 192.168.1.0 0.0.0.255 any
!
threshold of journal-update of 2147483647 IP access list
recording of debug trap
logging 192.168.1.5
access-list 199 permit ip 192.168.1.0 0.0.0.255 172.20.0.0 0.0.0.255
!
control plan
!
Line con 0
line to 0
line vty 0 4
exec-timeout 480 0
password 7 XXXXXXXXXXXXXXXlocal connection
entry ssh transport
!
Scheduler allocate 20000 1000
end
************************************************************************
CISCO 831
Version 12.4
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
!
hostname cisco831
!
boot-start-marker
boot-end-marker
!
activate secret XXXXXXXXXXXXXXX!
AAA new-model
!
!
AAA authentication login me local
!
!
AAA - the id of the joint session
!
!
!
!
No dhcp use connected vrf ip
DHCP excluded-address IP 172.20.0.1
!
IP dhcp pool mypool
network 172.20.0.0 255.255.255.0
WR domain name
Server DNS 8.8.8.8
router by default - 172.20.0.1
!
IP cef
no ip domain search
IP domain name mondomaine.fr
!
Authenticated MultiLink bundle-name Panel
secret user name me 5 XXXXXXXXXXXXXXX!
crypto ISAKMP policy 3
BA 3des
preshared authentication
Group 2
ISAKMP crypto key address 173.x.x.x mypassword
!
Crypto ipsec transform-set esp-3des esp-sha-hmac TRANSFORMSET
!
MYVPN 10 ipsec-isakmp crypto map
the value of 173.x.x.x peer
game of transformation-TRANSFORMSET
PFS group2 Set
match address 199
!
Archives
The config log
hidekeys
!
interface Ethernet0
LAN description
IP 172.20.0.1 address 255.255.255.0
IP access-group 100 to
IP nat inside
IP virtual-reassembly
!
interface Ethernet1
Description of the internet
IP address 173.x.x.13 255.255.255.248
NAT outside IP
IP virtual-reassembly
automatic duplex
card crypto MYVPN
!
interface Ethernet2
no ip address
Shutdown
!
IP forward-Protocol ND
IP route 0.0.0.0 0.0.0.0 173.x.x.14
!
no ip address of the http server
no ip http secure server
!
overload of IP nat inside source list 100 interface Ethernet1Crypto-list extended IP access list
ip licensing 172.20.0.0 0.0.0.255 192.168.1.0 0.0.0.255access-list 100 permit ip 172.20.0.0 0.0.0.255 any
access-list 199 permit ip 172.20.0.0 0.0.0.255 192.168.1.0 0.0.0.255
!
control plan
!
Line con 0
password 7 XXXXXXXXXXXXXXXno activation of the modem
line to 0
line vty 0 4
privilege level 15
transport input telnet ssh
!
max-task-time 5000 Planner
endA few things that need to be changed:
CISCO 2901:
(1) ACL 100 applies to GigabitEthernet0/1.1, however, I do not see 100 ACL configured on the configuration.
(2) ACL 101 is applied to GigabitEthernet0/1.2, however, I do not see that ACL 101 exists in the configuration.
(3) NAT ACL must exempt traffic between 2 local networks as follows:
NAT extended IP access list
1 refuse ip 192.168.1.0 0.0.0.255 172.20.0.0 0.0.0.255CISCO 831:
(1) ACL 100 is currently applied to the configuration section 2: NAT and Ethernet0. I would create a new ACL for instruction of NAT that should be added to the deny ACL (NAT exemption) as follows:
access-list 150 deny ip 172.20.0.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 150 permit ip 172.20.0.0 0.0.0.255 any
overload of IP nat inside source list 150 interface Ethernet1
no nat ip inside the source list 100 interface Ethernet1 overload
Hope that helps.
-
Collect data netflow on the load decrypted in IPSec traffic
Hello
I have a case where our customers have an IPSec Site to Site tunnel, where traffic is hair-pin on a 2901 router.
They would collect netflow on the load decrypted for accounting purposes.
The problem is that according to the order of operations on the router IOS, the netflow is recorded before the packet is decrypted penetration, and after the package is encrypted evacuation.
Is there a solution to this, or someone has experience with alternative solutions for this scenario?
(e.g. DURATION encrypted traffic to another device which decrypts and generate netflow data?)
Best regards
Steffen
Hey, Steffen,.
Yes the path of the EFC is so different [Card Crypto is a feature of output while the Tunnel Protection is a feature of post-encap].
Therefore, we can apply all feature output such as netflow on a tunnel or a virtual-template interface since then we validate the traffic post-decapsulation.
An example of one of my box [a vpn to 4.2.2.2 peer ping]. NetFlow which attracts traffic after decryption.
R1 - HUB #sh ip cache flow. I Vi1
Vi1 172.16.1.1 Et0/1 4.2.2.2 01 0000 0800 153
See you soon,.
Olivier
-
Hey everybody
Im a novice when it comes to Cisco routers. Having a 2901 in the House now and trying to do this route between the two main interfaces. But no luck!
Routing is between the 10.16.108.x and the 32.54.20.x network. The command "ip routing" was launched.
S * 0.0.0.0/0 [1/0] via 10.16.108.1
10.0.0.0/8 is variably divided into subnets, 4 subnets, 3 masks
C 10.0.0.0/23 is directly connected, Vlan1
L 10.0.0.7/32 is directly connected, Vlan1
C 10.16.108.0/22 is directly connected, GigabitEthernet0/0
The 10.16.108.2/32 is directly connected, GigabitEthernet0/0
32.0.0.0/8 is variably divided into subnets, 2 subnets, 2 masks
C 32.54.16.0/20 is directly connected, GigabitEthernet0/1
The 32.54.20.33/32 is directly connected, GigabitEthernet0/1The config set as a text file attachment.
Everything looks good on this configuration for basic routing. Is the test on the 10.16.108.0 computer network configured to use 10.16.108.2 as its default gateway? Similarly, is the 32.54.20.32 network is configured to use 32.54.20.33 as its default gateway? If the test machines do not have a path to the interface of the router, which will create a problem.
-
ALS IP Cisco 2901 and POLITICS with dual gateways LAN-based ROUTING
Hello
I am configuring a failover solution combined with the ACB using two bridges already configured. See the attached diagram.
I currently have two ASA 5505 and a 2901.
According to the example: http://www.firewall.cx/cisco-technical-knowledgebase/cisco-routers/861-c... I've set up the following in the 2901:
Interface Port - channel1.1
encapsulation dot1Q 1 native
IP 192.168.200.100 255.255.255.0
intellectual property policy map RM-Comcast-traffic routeIP route 0.0.0.0 0.0.0.0 192.168.200.200 track 1
IP route 0.0.0.0 0.0.0.0 192.168.200.150 track 2
Route IP 10.10.10.1 255.255.255.252 192.168.200.150IP extended ACL-Comcast-traffic access list
object-group permit COMCAST_Routed 192.168.200.0 0.0.0.255 anyRM-Comcast-traffic route map permit 1
corresponds to the IP ACL-Comcast-traffic
set ip next-hop check availability 10.10.10.2 1 excerpt 2object-group service COMCAST_Routed
Eq ftp TCP
TCP eq www
TCP eq ftp - dataALS IP 1
ICMP echo - 192.168.200.200
threshold 2
timeout of 1000
frequency 30
IP SLA annex 1 point of life to always start-time nowALS IP 2
10.10.10.2 ICMP echo
threshold 2
timeout of 1000
frequency 30
IP SLA annex 2 to always start-time life nowtrack 1 accessibility of als 1 ip
Track 2 accessibility of ALS 2 ipI did some tests and the part of failover seems to work but the configuration of the ACB does not work as expected. Only thing missing track 1 each time delivering properly and trak 2 is declining.
Any help clarifying the feasibility and practicality of this configuration is greatly appreciated.
Dan
Adding a value of AD won't fix ACB (sorry if I gave that impression).
On the client that you are testing with can you look it's the example routing table ' netstat - nr ' example and see what it shows in terms of gateways.
It can be that you want to debug your routing policy to see what is happening on the router.
Jon
-
How to change my password for wifi on my printer Canon MG 2950
How to change my Wifi password on my printer Canon MG 2950
Hi Piet,
Thanks for posting your query on the Microsoft Community.
According to the description of the problem, you are ready to change your printer Canon MG 2950 WIFI password.
Before connecting your PIXMA printer to your wireless network, check that you meet the following two conditions:
- Ensure that you have an access point (sometimes called a router or a hub) through which you get an Internet connection. Your access point must be fully functional before proceeding to the next step.
- Make sure you have a computing device, PC, Mac, tablet or Smartphone, here referred to as a computer that is connected to the Internet.
I suggest you to return the item mentioned below and see if it helps allows you to change the password for WIFI.
Setting up wireless PIXMA MG2950
Use of the Machine with the Access Point Mode
Hope that the information provided is useful. Let us know if you have any concerns related to Windows. We will be more than happy to help you.
Kind regards
Maybe you are looking for
-
Satellite A200 PSAF0A - cannot use the DVD writer / reader more
HelloAnyone has any advice on this? Laptop: Satellite A200, PSAF0ARequire: DVD burner / player sofware. My hard drive died last week, so a techno guy installed a new and reinstalled the OS (Vista)... everything works fine. But don't have Toshiba Util
-
"incomplete struct pointer" error
I keep geeting error "Type error in argument 1 of 'DLLStruct '; "found"pointer struct parameters' expected ' struct pointer incomplete parameters " I'm trying to pass a pointer to a structure as an argument to a function in a DLL. It's just a test c
-
HP Pavilion dm4-1160us: IDT high definition Audio Codec Windows 7
Just recently, I unplugged my USB of my laptop headset and now my sound does not work. I get this error in the properties of the IDT (= Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or softwar
-
Try to shorten the time between songs
Original title: Media Player If I am using windows media player and create a list of songs to play how shorten the time between songs, so we can finish and the next songs will start immediately?
-
New E4200, turns hot...
I've just implemented a new E4200 today (refurbished, but new to me * smile *), and I find it works well but it is running more hot that I'm comfortable with. Especially the Metal around the outside gets hot... I guess that the Metal is used to tran