Switch added, limited on 1 device connection

I recently added a ProSafe GS108 switch to my home network. My wired pc are able to access the internet, but my Android streaming media box has very limited connection, which means that I can do a speed test of the media box, access certain content streaming, but I can't access Netflix or all apps like gmail, playstore, etc. Any ideas?

It was a mistake to user on my side

Tags: Netgear

Similar Questions

  • EA6500 only shows no device connected to the switch of working group 5 ports

    I just replaced a defective Linksys e4200 with an ea6500.  After assistance by phone, I got to the top and work, but only one computer on my LAN is not displayed.

    I connected an 8 port 10/100 switch Linksys my 4200, and my wife's computer was connected to that.   The computer displays the IP as 192.168.1.133 and it is connected to the internet with my router again.  But the ea6500 does not show a device with the ip address.  Instead, he shows what he calls a network with the IP 192.168.1.130 device.

    How can I see the devices connected to the switch 5 ports and determine which ip addresses, they have been assigned?

    I use a switch with my network with a router EA and it shows the devices correctly. Turn off the computer which does not appear in the list of devices and check to see if any device will appear as offline adter who. Remove from the list of devices, and then restart the router. Once the router is ready, open the page of the router again and turn on the computer and check if it will be detected correctly. I hope this helps.

    Edit: Check and make sure you have the latest firmware loaded. Otherwise, update the firmware and do a reset after the update of the firmware. Check your list of devices after that.

  • limited access/no internet connection wifi at home

    I connect my laptop to router at home via wifi. But I had limited or no internet connections message often enough. Usually after the diagnosis, it will reconnect and works very well. However it will not work for long.

    Diagnosis looks like this

    And could someone help me with this?

    Thank you.

    Willa Hello,

    Thanks for posting your question on the Microsoft community.

    I would like to know some information about the problem so that we can help you better.

    1. What is the brand and model of your computer?
    2 - is your computer to connect to another wireless networks?

    Thank you for details on the question and your efforts to resolve.

    This problem can occur for the following reasons:

    -Wireless adapter switch is not activated.
    -WEP, WPA or WPA2 key or password security issues.
    -Cables are not connected properly.
    -Corrupt or incompatible drivers.
    -Missing updates.
    -Incorrect network connection settings.

    I would suggest trying the following methods and check if it helps.

    Method 1:
    Please use the suggestions provided in this Microsoft article knowledge based and check.
    Reference:
    Error message "your computer seems to be configured correctly, but the device or resource (DNS server) is not responding" in Windows 7
    http://Support2.Microsoft.com/kb/2779064

    If this does not help, use method 2.

    Method 2:
    Suggestions of use contained in this Microsoft Help article and check the issue.
    Reference:
    Wireless and wired network problems
    http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

    I hope this information helps.

    Please let us know if you need more help.

    Thank you

  • Switch Soft Front Panel, active device classified

    I have a with PXI chassis modules, two switches PXI-2350.  Using the Soft Front Panel switch, it seems that the names assigned to the list of active device (both 2350's in this case) are backward, what to expect.  Is there a way to reassociate those names to the 2350's physics?

    Thank you

    Confustus,

    It's an interesting question that I've never seen before, your devices in a Soft Front Panel should be linked to features like labels in MAX. I was wondering, when you say "we can select using MAX, a road that connects the power supply to the digital multimeter using"Switch 1"(for example), and we can see the voltage reading show on the Soft Front Panel 4071 as planned", what you mean exactly? If you had to choose your hardware device, and then click test panels, the NI Soft Front Panel load switch. Are you saying that when you choose test panels and loading Switch Soft Front Panel of max works as expected, however the application outside opening MAX does not work?

    Or are you talking about the Test panels you open in NI Switch Executive? The test for NI Switch Executive panels refer on behalf of virtual device NI Switch Executive, not the DAQmx device name. If you had named the name of the NI Switch Executive virtual device in the same way, that could be part of the confusion of the problems that you see. See the images below:

    NEITHER DAQmx Test selection panel that leads upward.

    Test NI Switch Executive Panel allows this. If these names are similar, I can see how that might be confusing.

  • Get the IP addresses of the devices connected to the WiFi network

    Hello guys,.

    I've been looking around and trying to understand this point, but I don't have a solution. The problem is to get the local IP addresses of all devices connected to the WiFi point of access/router connected to my BlackBerry. Similar to the way in J2SE nature you can get the IP using InetAddress.getLocalAddress () and then browse ip addresses and call InetAddress.getByAddress (ip) to check whether the device is accessible. Possible is something similar in BlackBerry or not?

    No, the fault was entirely mine, I misread your message.
    no idea how to do that, there is no access from low level of the network interface and the API is really limited.

  • Email rec'd 'a device began synchronizing with devices connected to your Firefox account' Please explain

    What is happening with my account of Firefox? I received an email as follows: «a device started syncing with devices connected to your account in Firefox» If there is a security problem, Firefox's history on all my computers. Please explain what is happening here quickly. I think I'll remove the Firefox browser everything and start over with someone else. I can't take risks with my information.

    This isn't a security problem. With the team of Mozilla Sync, I have confirmed that it is an email waiting turning Sync in Firefox on a new computer, tablet or phone. In the future, they will cease to send this type of email to avoid worrying people.

  • Qosmio G50-12 q - how to configure the devices connected to the USB mode standby

    Hello

    I wanted to use the PC sleep function.
    I also wanted to as devices that have been extinguished when in stand by.

    Once implemented this function the PC will regularly stand-by, but the device connected by usb are set on fire, any other master type, a device a usb wi.fi, etc.

    Someone told me that maybe some functions in the Bios only are not put in place to do that once entered the booth by the PC off all devices those connected.

    What checks and I have to perform in the configuration PC bios?

    How we in the bios? By pressing the keys on which?

    Thank you

    * valkyrie @ *.

    Please post comments if workaround posted by Akuma helped!

    It would be really appreciated.

  • Equium P200-1ED is able to power external USB devices connected on it?

    (1) is anyone able to confirm if the Toshiba Equium P200-1ED is capable of powering an external USB device connected to it via one of its 6 USB ports?

    (2) what is the maximum power that the Toshiba Equium P200-1ED can provide only one USB port?

    (3) can the Toshiba Equium P200-1ED providing the power referred to in Question (2) above to each of its 6 USB ports?

    Please don t after several markets on the same subject.
    After you recommend first one:

    http://forums.computers.Toshiba-Europe.com/forums//message.jspa?MessageID=115025#115025

  • My devices connect only to an airport machine

    I have two extremes of the airport, which connects to my modem and creates a network and one which runs the network. However, all of my devices are connected to the Airport Extreme that creates the network. What I am doing wrong? They are on different floors of the House and appear to be configured correctly, but the devices that sit on adjacent to the Airport Extreme, extension of the network does not connect to it. I know your supposed to have an Airport Extreme and multiple Airport Express, but we already had the old (4th gen. I think) Airport Extreme, so we decided to use it. Thank you!

    There is no difference between express and extreme to extend...

    However if you started near the main AE... you must turn off the wireless and then turn it back on... and it needs to connect to the Extender.

    Unless you have a problem in the configuration.

    Post screenshots of airport utility and we see what happens...

    Remember, if the signal is bad for the AE on the upper floor... It can transmit a signal any better than that. So if the client devices connect ok the Repeater is in the wrong place.

  • Satellite A30 does not start with the USB device connected at boot time

    Hello

    I have a Satellite A30 and sometimes it does not start.
    After turning on, not even the BIOS starts.
    even if sometimes the BIOS starts, but the OS does not load.

    I figured out that its related to USB devices connected at boot time.
    If no USB devices are connected, it starts without a problem.
    Even if the start-up is suspended, as soon as you unplug start it BIOS USB devices.
    Its ok to connect USB devices later, once the system has started.
    I disabled "removable devices boot" and "network startup."
    just in case, but it makes no difference.

    BIOS is version the most recent (1.70) and it comes up with all kinds of USB devices.
    printer, mouse and (self-powered) external USB hard disk.

    Is this a known issue?
    There is no known workaround solution?

    Hello

    I put t know why this happens, but it has to do with the BIOS.
    The same thing happened on my old laptop. I couldn't start my unit while the USB printer has been turned on and connected.
    The only solution is to disconnect the external USB device during the boot process.

    RSY you should check if the order of boot in the BIOS has been on the HARD drive first.

  • Is there a way to see the ip address of the devices connected via the airport?

    Hello world

    Is there a way to see the ip addresses of the devices connected via the airport? I can see the name of the devices but not what ip are they?

    Thanks in advance.

    Open AirPort Utility

    Hold down the option on your Mac so you double-click on the image of the AirPort router

    Wireless clients are displayed

    Click on the small arrow next to each wireless client to see details about the device and the connection

  • Device USB not recognized - device connected USB has malfunctioned and Windows does not recognize it

    I have a HP Pavilion dv4 laptop running Windows 7 Home Edition Premium and the USB ports worked well for a HP deskjet printer and an older Casio digital camera. Then one day, the laptop decided not to recognize the Casio digital camera and gave the error message "USB device not recognized" and also indicated that the device connected to the computer has malfunctioned. This prompted me to buy a new digital camera Canon. Well, a new camera has not fixed the problem. Now, anything that is connected to one of the 2 ports USB will not be recognized by my laptop. Help!  I am at a loss to understand this.  I tried using Microsoft suggested below:

    Suggestion 1: the problem with USB devices, uninstall and reinstall all USB controllers. This allows controllers to recover the port USB of his condition does not respond.
    USB controllers represent the USB ports in Device Manager.

    a. Click Start, type Manager of devices in the search box of start and press ENTER.
    b. expand Bus USB controllers.
    Note: you may scroll through the list to find this point.
    c. the first USB controller under Bus USB controllers right click and then click on uninstall to remove it.
    d. Repeat steps above for each controller USB is listed under Bus USB controllers.
    e. restart the computer. After the computer starts, Windows will automatically check for changes on the hardware and reinstall all USB controllers that you uninstalled.
    f. check the USB device to see if it works.

    This has not fixed the problem.  Then the Device Manager, I tried to update the drivers on all the USB controllers and root hubs. While some may have received software updates downloaded, it still has not corrected the problem of unrecognized USB device after the computer is restarted.  I hope that someone knows the solution to this situation and can pass it on to me. Thanks for reading and any help display.

    Read previous messages revealed the solution for USB devices not recognized on my HP Pavilion as well as several other laptop models.  Shut down the computer and remove the battery and wait for about 15 minutes. Reinstall the battery and restart the computer.  USB ports are working to download pictures from my digital camera from Canon and charging a cell phone, etc...   I hope it helps others with this problem!

  • Do output sony 5.1 HDMI, audio devices connected TVS optics carry

    Hello

    Try to connect it to an existing SONOS system.

    All HDMI devices must connect to the TV.

    Worried that Audio optics translates PCM instead of keep 5.1 if it is how the content is

    Thank you

    Chuck

    Yes, the optical port of the TV would be able to sound output from devices connected using HDMI connection. Make sure that the settings on the source device is set to 5.1 surround sound output.

    If my post answered your question, please mark it as "accept as a Solution.

  • We are trying to install FSRM (File Server Resource Manager) in windows server 2 k 3 R2 SP2. After installation, its error message that gives as no network device connected. Suggest me!

    Original title: problem in installing FSRM

    We are trying to install FSRM (File Server Resource Manager) in windows server 2 k 3 R2 SP2. After installation, open the FSRM in "All programs", its error message that gives as no network device connected.  Suggest me!

    Hello

    Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows 7 networking forum.

    http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

  • Audio event system has detected a device connection event audio location description of the Panel right-Black Jack

    I have no sound on my Dell inspiron 6400. Volume is not muted, sigmatel peripheral is enabled, hardware (speakers laptope) work, drivers have been updated and reinstalled.  Windows xp service pack 3.  The problem occurred after that children were playing a game of Dora on CD.  Above the popup of the event (System event Audio Audio System has detected a device connection event audio description location of the right panel Black Jack) appears.  Can get sound by using an external speaker.

    I note a number of comments suimilar on other sites but no resolution on these offers from

    If you go into Device Manager, you see a yellow fringe (!), which reports an error?

    To access the Device Manager in Windows XP:

     
    1. Click Start and then click Control Panel.

    2. Click the performance and Maintenance link.

      Note: If you see the Classic view of Control Panel, you will not see this link. Simple, double-click on the System icon and go to step 4.

    3. In the performance and Maintenance window, click the icon at the bottom of the window .

    4. In the System Properties window, click the hardware tab.

    5. The hardware tab selected, click the Device Manager button.

    Double-click sounds and game controllers.
    This will bring up a dialog box. From there you can update drivers, see the details of driver and driver rollback.

    If you uninstall CD Dora, you are able to get her back? It may be a conflict with the 3rd party product.

    Please let us know.

Maybe you are looking for

  • Firefox blocks popups online even quickbooks after adding to the allowed list

    After the recent update of quickbooks online when using certain functions, a popup is apparently blocked by Firefox and I get a message from qb saying: ' uh - oh. " Please unblock us. We use pop-ups for things like adding new clients, showing alerts

  • Battlefield2 - Qosmio Go5700 GeForce drivers

    Played Battlefield2 demo! bad guys. Everything works great, but... notice keep coming for updating me nvidia drivers at latest for optimal purformance and I need optimal performance for this game trust me! so... do anyone know where to get your hands

  • M6-1035dx Pavilion: Pavilion m6-1035dx touchpad y axis too sensitive after upgrade Windows 10

    I installed my m6-1035dx Pavilion at 10 Windows laptop. Everything seems to work pretty well, except the touchpad. The Synaptics 10 Windows driver is much too sensitive along the y-axis (vertical movement), but it is very well along the x-axis (horiz

  • Paper jam error

    Hello Three weeks ago, I bought a HP Envy 7640 all-in-one printer. It worked fine until I hit a 'paper jam error. I worked through the step by step manual HP full address (cleaned, checked, rebooted etc.) to fix this one, but nothing helps. I'm sure

  • How to acquire data from the memory of the meter

    I am a beginner of Labview. I don't know how to acquire data from the memory of the meter. I read a few examples of data acquisition, but apparently not similar to my case. I can't use DAQ in my computer, because I don't have DAQ card. Could someone