Switchable graphics or in the power saving mode by default

Similar Questions

• Tecra S10 - USB-power does ' t stop the power saving mode

  I have the following problem.
  USB power on the right side three ports USB does´t closed the power saving mode.

  Only when the system is switcht off power on USB ports is disabled.
  What can I do?
  Thanks for a response.

  Hello

  You can check in the BIOS if the option called USB Sleep & Charge has been enabled or disabled.

  Change this setting and save the changes. Then start again.

  Check if you can see any improvement.

  Welcome them

• Satellite A200-1IZ becomes extremely slow using the power saving mode

  Hello

  Since I installed windows 7 I can't use my computer in battery saving mode because it becomes extremely slow.

  It takes so long for trivial tasks. It is virtually unusable.

  Can anyone tell me the reason for the problem and if there is some sort of solution?

  Thank you.

  Hello

  What performance maximum CPU you have for the power saving mode? Check the Windows power management settings: start > Control Panel > Power Options.

  The plan for the power saving mode settings and make sure that the maximum performance of the CPU is at 100% for the power saving mode. This increases the performance of the computer.

• U2414H, Macbook Air, waking up to the power saving mode

  When my MacBook is sent to sleep or I shut down the computer, the monitor will sometimes get stuck in a loop where he wakes up "Power Saving mode" then displays "Enter Power Saving Mode" then shut off again and repeat in less than a second. Also while I was trying to open the OSD menu to check if the resolution is set correctly (as described in validation) capacitive buttons are just hard does not work. Hope you can help.

  Serial No.: CN-0H8H7G-74261-46 b-36GL
  Revision A01
  Included computer: MacBook Air mid-2014 connected via mini-DP to DP cable
  Intel graphics card internal HD5000
  Run monitor to 1080 p 60 Hz

  The air doesn't have a DP (DisplayPort). It uses Thunderbolt. So, how you connect to our RFP U2414H?

  Unfortunately, Dell does not validate the test / this model of monitor on Apple, ports and software hardware. For this reason, Dell has no troubleshooting steps a lot to offer. You can post on the Forum of Discussions Apple and see what they say. Some apple users have mentioned using a bolt of lightning to HDMI adapter or love at first sight for adapter DP has had some success.

  Apple computer thunderbolt port--> crush on HDMI adapter--> Dell HDMI to HDMI Cable TYH2W, W69C3--> Dell monitor HDMI port

  Apple computer thunderbolt port--> crush on CDM--> Dell DP DP adapter cable--> Dell monitor port CDM

  Apple computer thunderbolt port--> maid in CDM adapter--> Dell mDP to DP cable--> monitor Dell DP in the port

  You have the latest version (11 June 2014, A01). Users of Windows 8/8/1 under their power management windows computer balanced high performance which fixed some issues wake-up call. Windows 8/8.1 on balanced allowed the DP computer to go to sleep. He confused the handshake of DP at the end of the screen. Have you tried to test with DP1.2 disabled in the OSD menu?

• Win 7 pro restarts of the power saving mode

  Win 7 pro, power saving mode - go to sleep, don't restart; do restart main power.

  I changed the power save settings especially the time to go to sleep; He then worked for some time then don't reboot again.

  These could help you - the problem is normally attributed to a graphics driver that requires an update, but these links go to other possible causes as well.

  The problems of wake the computer from sleep - mouse-keyboard problems

  list of sleep problems - see entries by SpiritX

  Monitor won't wake from sleep - MyPCHealth

• In use, IE. even when playing a windows game will enter the power saving mode. All the solutions for this?

  It was produced for about 1 month without no reason that I can find.

  Hello Keir,

  Follow the following steps:

  1 plug in your power supply. Click on "Start" on your computer screen, then click on 'control panel '.

  2. double-click on the "System management" link and click on "Power Options."

  3. Select 'High Performance' under the power plan window. Click 'OK' to save the changes. This will disable sleep mode auto power saving.

• stand-by power mode re - begins shortly after entering the power saving mode

  My other machine stand-by mode and then the power automatically back up after about 30-40 seconds

  Hi sibsales1,

  1. When did you start the questions?

  2. you remember to make changes to the computer before this problem?

  You can check the following link and try to run the Fixit and see if it helps:

  Solve power problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-power-problems

  If you are still facing problems, then check the advice given to "my computer suddenly wakes up from his sleep" in the link above.

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• don't leave the power saving mode

  I have a dell dimension c521 with vista. When I start it up, it goes right to power save mode. It says to press the keys or move the mouse. The mouse does not light, but the keys do nothing. Ive tried unplugging, restarting, gathering dust. Nothing seems to get out of power save mode. All this started after I downloaded Norton360 security. I need help!

  http://www.Symantec.com/support/index.jsp

  Contact the Norton Support link above, as you say that it began with the installation of Norton.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Try this:

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  Mick Murphy - Microsoft partner

• How can I activate the remote computer to power saving Mode monitor?

  I am a technician in a small private company and it is my duty to keep all desktop computers works very well.
  Desktop computers:

  • are the Dell Optiplex GX260
  • Run Windows XP SP3
  • have Dell 17 "monitors
  • with Intel Pentium 4 (2.4 Ghz) processor with 1 GB RAM

  I do my job after working hours. I connect to them with my laptop (running Windows 7) and check their conditions, one by one. Now, my employer comes to know that when I do this whole process monitors for desktop computers continue to run. As it is not put in place a very large company and electricity and the price of fuel in Pakistan are very high. So, he asked me to find a way to turn the monitors to the power saving mode, when I do my work. In this way, it will be significant energy savings and fund savings in monthly bills. So, can someone please tell me How do I turn on monitor of the remote computer to the power saving mode?

  There are several ways to handle this.

  #1-have affected the power turn on their monitors, but let run PC
  #2-click Start > Control Panel > Power Options and choose how long it is before the screen turns off. Once your activity on their machine is complete, then will kick time.
  #3-you say that you connect to their machines to check their conditions... whatever that means exactly. You can map their computer management console directly to your machine and I * think * he didn't wake up the monitor.

  I hope this helps.

• My computer is stuck in power saving mode

  Hello. I need your help guys. My computer won't come out of power saving mode. I was chatting with someone on MSN and light of my computer went from blue to orange and my screen went black and I got the message "power save mode, press any key or move the mouse to leave". I pressed all the keys and moved the mouse, but it wouldn't leave the power saving mode. I unplugged my computer and I even changed around the RAM cards. I took the CMOS battery and tried. Nothing has worked. I also took my videos and my graphics driver cables. Still, he doesn't after that I put everything in place [except the drums]. Recently, I put the battery back in and it still doesn't work. I dusted off my gear inside my computer and cleaned the fans. There is this light inside my orange computer as soon as I put the power cable at the back of my pc. I don't know what to do. It's so frustrating. I need your help! Here are a few photos from my computer (Dell Inspiron 530 s, A).

  1: http://tinypic.com/r/28vwufp/7
  2: http://tinypic.com/r/dwvzhz/7
  3: http://tinypic.com/r/1444ojt/7

  Here are the pieces of vaues for numbers of image 3:
  1 - socket processor (CPU)
  2 - connector (CPU_FAN) CPU fan
  3 - connectors (DIMM_1) memory
  4 - connectors (DIMM_2) memory
  5 - connectors (DIMM_3) memory
  6 - connectors (DIMM_4) memory
  7 - main power connector (ATX_POWER)
  8. Jack battery
  9 - connectors (SATA0) SATA drive
  10 - CMOS jumper (CLEAR CMOS)
  11. password jumper (CLEAR_PW)
  12 - connectors (SATA1) SATA drive
  13 - connectors (SATA4) SATA drive
  14 - connector (F_PANEL) front panel
  15 - connector (F_USB1)
  16 - connectors (SATA5) SATA drive
  17 - connector (F_USB2)
  18 - modular connector (F_USB3) before
  19 - front audio (F_AUDIO)
  20 - connector (PCI2) PCI
  21 - connector (PCI1) PCI
  22 PCI Express x 1 Connector (PCIE_X1)
  23 PCI Express x 16 connector (PCIE_X16)
  24 - audio connectors
  25 - 2 USB and 1 LAN connector
  26 - 2 USB connectors
  27 - connector (CHASSIS_FAN) chassis fan
  28 - video connector (VGA)
  29 - power supply of the CPU (ATX_CPU)

  Thanks for your help in advance!

  E-mail: * e-mail address is removed from the privacy * [contact if we need to discuss.

  Hi xxbrgxx,

  You can see the steps mentioned in the links of dell under which addresses question power saving mode

  http://support.Dell.com/support/eDOCS/monitors/1901FP/en/trouble.htm

  http://en.community.Dell.com/f/3529/t/17144276.aspx

  If the problem persists, contact dell for assistance more specialized on this issue.

  http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

  Thanks and greetings

  Ajay K

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Computer keeps going into power saving mode

  Hello, I'm fighting with my pc it keeps going on the power saving mode how to stop what I sometimes lose my job

  Original title: URGENT
  Moved from the community involvement Center

  Disable saving energy mode in Windows 10

  1. Click Start
  2. Type power and press ENTER to open it
  3. In Option of power--> the window on the right panel under ' choose or customize a power pan "selected Plan is a balanced.
  4. Then click on change plan settings
  5. 
  6. This will open the Edit plan setting window
  7. To turn off the screen FOREVER in both batteries & Plugged In
  8. Make sure you put the computer to sleep FOREVER in both batteries & Plugged In
  9. 
  10. Then click on save changes
  11. This will save it, and you're done!

  Note:

  1. Battery: It will accordingly when the system is on battery Mode (load is not Plugged)

  2. Plugged in: Will accordingly when the system is Plugged In to the wall (the charger is plugged in)

• computer freezes and goes to power saving mode

  Several times a day my computer freezes and goes into the power saving mode.

  Hello
   
  1. have you made changes on the computer recently?
  2. do you use a particular application when your computer crashes?
  
  Method 1.
  Check to see if the problem exists in Safe Mode, if the computer works as expected in mode without failure, then we can solve the problem in the clean boot state.
  Step a. refer to the article below for the procedure safe mode in Windows XP
  A description of the options to start in Windows XP Mode
  http://support.Microsoft.com/kb/315222
   
  Step b. You need to perform a clean boot to find the program that is causing and then disable or remove.
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353/en-us
  Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.
  
  Method 2.
  Also, check the logs of the observer eveny for recent activity on your computer and check.
  This article describes how to use Event Viewer to view and manage the event logs in Microsoft Windows XP.
  Procedure to view and manage event logs in Event Viewer in Windows XP
  http://support.Microsoft.com/kb/308427
   
  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Updates made now computer won't start and power saving mode

  After going through the procedure that I received the usual message "loading down updates 1 of 9 please don't turn off your computer ' closing, so I left and went to bed. The next morning, but when I turned on my computer as it has been commissioning a box came on my screen "power saving mode" and entering power saving mode nothing happens. I then turn off my computer and then put it again by pressing F8 I hope go to the options of allowing me to boot in safe mode so I can take it from there. However, this does not work and once more, he'll just right to the power saving mode and is right. Y at - it someone who has ideas for what to do. I am running Windows Vista, if this is useful.

  Hi FrankSpencer,

  Follow the steps below and see if they help.

  Step 1:

  Do Startup Repair from the windows installation disc and check that if it helps, here is the link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

  Step 2:

  If this does not help, you can do a System Restore from the system recovery options.

  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• My Dell is power saving mode and will not come out

  My Dell is power saving mode and will not come out? Any suggestions? I can't get anything else than a screen that says it is in power save mode and press a key or move the mouse. No one who does nothing. Don't disconnect.

  Hi Ma32206,

  Monitors Dell will automatically mode energy saving after a predetermined time amount when the computer is idle. The Dell monitor will go completely black, rather than display a screen saver. This allows your monitor to essentially turn off until it takes again.

  A. Press any key on the keyboard or move the mouse. Either will automatically turn off the power saving mode. Alternatively, you can press the power button on your Dell computer tower or laptop.

  B. press one button a second time if the monitor goes power saving in standby mode. Standby mode allows the screen saver appears.

  Bindu R - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• DELL UltraSharp U2515H Monitor - fixed the power LED mode indicator sleep?

  Hello

  I just bought a monitor DELL UltraSharp U2515H 25 and in the course of the day before (Mini DisplayPort) Power LED flashes during the standby time.

  Can you tell me if this is normal?

  This indicator returns to fixed when using the display and it is possible to turn off the light while turning on the unit via the OSD menu. (Page 41 of the french DELL user guide)

  The link provided above a video illustrating the behavior of the screen (IMG_7073.MOV)

  Manufacturing date: Apr. 2015
  Review: REV A01

  Thank you in advance for your support.

  Kind regards

  Stone

  It is normal to blink while it is in standby mode. White light indicates the monitor is on and fully functional. A glowing white light indicates the power saving mode. Did you put the Power button LED "off during active?