synchronization of two DAQ 6218 M-series

Hello world

I try to sync both units DAQ 6218, but I get error 89136, declaring that I use incorrect routing. I've been watching a lot of messages and I couldn't find one that explains how the physical linking two devices - less do not so much a newbie like me could understand

I tried to look at NI_max to see the possible route, but he did a lot of sense to me. On my device, I can't find any I / O named PFI, but I divided for use off-device #1 P & P in the #2 device.

I have attached a photo of the VI, the ni_max interface and the other physical configuration.

I hope there, can someone help me, thanks!

Hi guys, I'm sorry that I have not answered your responses which are very appreciated.

I found that I was actaully comes to really make a rookie mistake. I had connected 'out' to 'out '.

Sorry to have wasted your time :/

Tags: NI Hardware

Similar Questions

  • NOR-DAQmx C to run two cards USB M series

    Hello

    I am a newbie in working with DAQmx system and need help on the synchronization of multiple USB DAQ devices. The goal is to start the collection on two USB DAQ for M-series card, and we use C codes (via the DAQmx ANSI C library) to do this. I read and resources OR more guides: "Several hardware DAQ synchronization" (http://www.ni.com/dataacquisition/videos.htm), and examples of code on the dev box NOR: "NOR-DAQmx: HAVE / simultaneous in CVI AO" (http://zone.ni.com/devzone/cda/epd/p/id/879).

    My understanding is as follows:

    1. set the first card as the master and export the signal 'StartTrigger' and 'SampleClock' PFI1 and PFI2 (the physical axis).

    2. connect physically with pin PFI1 and PFI2 (sources) of MasterCard wire on pin of PFI0 and PFI1 (destination) in the slave card.

    3. set the task of the slave to use the beginning of digital dashboard using PFI0 and configure the sample clock of the slave task to use the clock of the source of the exported signal from main task to PFI1 (the slave PIN).

    So far the result does not work. The error still shows as if the physical connection is not recognized (I have not yet found a way to check if the signal exported successfully or not).

    I have attached the instant routing table to the map created in the MAX and the code snippet I used.

    Any help is welcome. Thank you!

    Hi kusg.

    DAQmx unclear that some PFI terminals on your two devices are interconnected, and you can't tell him that they are connected because DAQmx only supports connections inter-appareils for chassis PXI, not PFI terminals and cables of the RTSI. So export terminals PFI of Dev2 Dev1 task signals won't work.

    However, you can export terminals PFI of Dev1 Dev1 task signals. Try to do this instead, and the error should go away (as I think it is to assume that it is error-89124).

    In addition, when you use PFI, I recommend committing the master task before you begin the task of the slave, to start the master task does not generate unwanted edges digital:

    DAQmxTaskControl (masterTask, DAQmx_Val_Commit);

    DAQmxStartTask (slaveTask);

    DAQmxStartTask (masterTask);

    Brad

  • I'm trying to move a song to my iPhone music library to the iTunes library on my MacBook Air.  I do not want to synchronize the two, so how do I simply copy/migrate the song on my computer?

    I'm trying to move a song to my iPhone music library to the iTunes library on my MacBook Air.  I do not want to synchronize the two (and they have never been synchronized), so how can I simply copy/migrate the song on my computer?  Is there a way to do, without having to re-purchase the song on the iTunes Store on my Mac?

    E-mail (for yourself) click on it in the email

  • problem with install two DAQ in a PC and missing DAQ assistant

    Hello

    I have two 6023E DAQ cards and 6024 and each card has its own DAQmx (DAQmx Vresion 8.7 for 6023E DAQ) and Version 9.1.7 for DAQ 6024

    and I want to install the two ofl these cards together in a PC with LabView 8

    After LabView installation and installation of cards if I install the drivers of DAQmx version 8.7 I don't miss assistant DAQ but NATIONAL & MEASURMENT > DEVICE INTERFACE AND I DAQ 6023E in traditional mode and I can not use traditional DAQ and the DAQ assistant in labview 6024 is also not recognized

    If I install DAQmx worm. 9.1.7 in NATIONAL & MEASURMENT > DEVICE INTERFACE AND I the two DAQ (not in traditional mode), but I've lost assistant in LabView DAQ

    What should I do?

    Please help me...

    Problem solved:

    I have install LabVIEW 2009 and then install DAQmx 9.1.7 and the problem resolved

    Thanks to all the bodies of their response.

  • Help the records removed from synchronization between two databases

    Hi guys,.

    I am new SOA and process management, so please bear with me.

    I created composite simple synchronization using two Dbadapters. A DbAdapter to share records and others to insert and update data in another database. My question is how can I detect deletions and delete records in another database.

    One of my friends told me to use DB triggers, but I want to do with SOA application using preferably the BPEL components.

    Any help would be useful.

    Thank you

    You can query the database if records are soft deletion, survey in the soft deleted records and then update the database target.

    If these are harsh destruction then the only thing I can think is: -.

    Source database: select * from source

    Target database: delete all records

    Target database: insert the records from the source.

    Other triggers would be best.

  • Synchronization of different DAQ devices

    Hello dear members,

    I want to order the spindle motor. He needs three analog time delay signal to the reader. With the LabView program, I generated the three delay time of signals. But I have the hardware DAQ who have only two analogue output pins. So, I decided to use two data acquisition devices so that can get three analog output ports. I'm a little worried about the synchronization between the two Renault. I will be happy if someone can help me to let the different Renault synchronization procedure.

    Thank you in advance.

    Best regards

    Azim

    Hello azeem,

    There are different ways to sync a/o on the DAQ hardware. However, it depends on what devices you use. Could you tell me what DAQ hardware you use? LabVIEW coding is not very difficult, but how you connect the hardware will be different. For example if you use two pci cards you can connect them via a RTSI cable; Use them as master and refer to the clock out of the master.

    Kind regards

    Jonathan P

  • I want to create communication between two laptops by Bluetooth series

    Hello

    I'm trying to accomplish communication series between two laptops via a Bluetooth connection.

    The two laptops are NOT portable Toshiba, but they work together the Toshiba Bluetooth Stack For Windows. They have both also use the default Bluetooth Manager program supplied by Toshiba and Dell (just rebadged?).

    Basically I can set up a connection no problem, but then I have never send data serially from one computer and watch the receiver serial port on another computer but nothing happens.

    Is there a good tutorials for this? It would be nice to have something for the Toshiba Bluetooth Manager especially windows and buttons have names as explained in the tutorial.

    Thanks in advance.

    Adam

    I tried via a hyperterminal connection for testing purposes and it worked.
    Maybe the description also contains useful information for you.
    It is here:

    PC1:
    Start "Bluetooth settings-> Mode custom-> Select Remote PC-> Select"Serial Port"-> Accept proposed (in my case COM40) COM-> Confirm Assistant windows port
    until the installation is completed".

    PC2:
    Start 'HyperTerminal-> Select COM7.

    PC1:
    Start 'HyperTerminal-> Select COM40 (in my case. (See step 1 above) »

    PC1, PC2:
    Enter the password even if security is enabled for example "0000".

    PC1:
    Everything you type in HyperTerminal must be visible in HyperTerminal of PC2 and vice versa.

  • Error-200284 when using two daq cards

    I have an application written in Visual C++ that reads data out of a data capture with success card. However, now we want to add a second DAQ card, so we can increase the number of input channels. However, I have trouble getting the second card works fine. He continues to give the 200284 whenever I try to read the input data. I tried playing with the two loops in the same thread and with them in threads separated without result. Any ideas on what could happen?

    Thank you!

    Hello Kaladin,

    I'll take a look at the link below to see the cause of the error, but also some common things suggested to try.

    http://digital.NI.com/public.nsf/allkb/FEF778AD990D5BD886256DD700770103

    Best wishes!

  • Can I synchronize list XCP DAQ with my analog input data data?

    Hi all

    "I use ' ECU M & C" for measurement of a computer data using the XCP DAQ list. "The data is read at the sampling frequency I put in ' MC DAQ initialize.vi. This works well.

    I want to associate this data with my DAQmx device measures. Is it possible to synchronize the clocks of the sample (by RTSI?) in the same way, it would be with DAQmx CAN synchronize data?

    Material: NO PCI-CAN/2 & OR PCI-6229.

    Thanks for any input.

    PJ

    Hi PJ,.

    Well, I think I understand now, I don't know why I DINA see this before. It is not possbile to do this with the ECU Measurement and Calibration Toolkit, sort of XCP DAQ, is not something that you are able to do.

    Best regards

  • Continuous acquisition and synchronization of two scanners

    Hello!

    I use two scanners high-speed NI PXI-5124. I'm running a continuous acquisition as in the attached example. I have two questions:

    (1) is it possible to make life-long using another source of trigger software INSTEAD?

    (2) depending on the answer to the first question - how to synchronize two scanners? In the attached example scanners have the same source of the clock, and they receive the same synchronization synchronization signal so the sampling rates are the same, but there is a lag of random phase each time I start the acquisition.

    Thank you!

    IVA

    Hello, Mateusz!

    I just apply the idea in the examples, as well as ideas from here, and here is the solution that works.

    Thank you!

    IVA

  • Synchronization of two inputs frequency meter with several analog inputs

    Hi all

    I'm relatively new to LabVIEW and I'm trying to collect data from multiple sources with calendar sync on the acquisition, but I can't understand. My problem is that I have two inputs frequency meter, an optical tachometer reading one pulse per revolution and a max flow meter machines with a 12000 k coefficient. I can't find a way to synchronize the calendar with my multiple analog inputs. I tried to first get the speedometer to synchronize with the analog inputs following the example linked here. (https://decibel.ni.com/content/docs/DOC-10785) So far every time I run it I get an error on the DAQmx read timeout or an error "several sample clock pulses have been detected" (see image).  It seems if I slow the way to down to say 10 hz and make sampling rate ensure that the tachometer signal is more than 800-1000 rpm (13-17 Hz) before starting the VI then the program will run without error until the ROTATION speed is below this threshold, then the "sample Multiple clock pulses" error occurs.  The code is attached below.

    Does anyone know of a better way to synchronize the entries of frequency of the counter with analog inputs?  I would like to have a VI that can display 0 RPM (and possibly 0 flow as well, but I think I need to understand the timing of a meter before I have add another, because it seems that I can't have two counters to the same task). Any help on this would be greatly appreciated.

    LabVIEW version 13.0

    Chassis cDAQ-9178 with NI 9401 for both counter inputs and NI 9205 for the analog inputs.

    Thank you!

    Richard

    I know the error requires to restart the task at least (this particular error puts the material in a State that cannot be recovered from during execution of the task - I've been down this road before) but I'm surprised that you would have to delete and re-create the task altogether.  And then I had to do this to workaround other questions in the past.  It is awkward and should be considered a bug, if this is indeed the behavior.

    Honestly, regardless of this bug, the way the material dealing with the situation of several sample clock edges makes measures of sampling frequency clocked essentially unusable for purposes of synchronization (in my opinion anyway) If you encounter a more slow than your sample clock rate.  You are supposed to be "synchronization" of the measure, but it really no longer applies if you have to restart the task over and over again (if you must delete it or not).

    Workarounds can get kind of creation (which isn't really a good thing).  For example, you can configure a measure of implicit frequency to keep a buffer of frequencies and use a leader board task (source is the frequency signal, sample clock is the sample clock HAVE) to establish a correlation between the index of your buffer of frequency for singing HAVE sample clock.

    Best regards

  • Synchronization of two SMU 6537 in acquisition mode

    Hello

    I need to use two SMU 6537 in parallel for a digital acquisition, their examples of clock is synchronized and running at 50 MHz. In the manual, I can't know is possible to correctly route connections through PXI background:

    -It seems that the path available only for export SAMPLING CLOCK in acquisition mode is 5 PFI, so no way to settle the two cards in a master-slave via the background.

    -I don't see or can use the background 10 MHz REFERENCE for synchronization, because it seems impossible through the DAQmx driver to deliver this line as input for the time base and trigger (it is not even in the list of possible signal entries).

    -The manual States that the maximum allowed value for an external time base is 50 MHz, whereas I need 50 MHz acquisition rate. I guess I should put in Sync synchronize databases internal time of the two councils through the background, but I can't figure out how.

    Any suggestion on how to solve this problem?

    Thank you, Piero.

    Piero,

    TO synchronize these cards, you must share the sample clock and a start trigger.  You should be able to send the sample for PXI Trig 7 line clock and use it for each of them.

    -Christina

  • synchronization of two loops for...

    HII...

    I am using two loops for and I want each iteration for both loops start at the same time...

    in fact I want to sync between these two loops...

    so when the each iteration of the two loops will start at the same time then these will be synchronized...

    also if a loop takes more time in an iteration the other loop should suspend until the end of the iteration of the other...

    please me... thanks hlp...

    Hi samir,.

    two options:

    1: when both FOR loops should have same time iteration why not just put all the code in a loop FOR?

    2nd: when 1 is not possible/wanted, you can use a notification utility. Set the notifier early iteration of the first for a loop and wait for the signal in the second loop...

    3rd: use call loops and synchronize them...

  • LabVIEW code for two daq cards

    Hi all

    I'm reading the analog signals using the USB-6210 device and function DAQmx. How to write my code so it would work with the NI USB-6210 or USB-6218 since both a pinout similar devices.

    Thank you

    dp128

    Do not write anything to recognize a different DAQ card. It's as simple as that. They both have the same number of input channels, and they both have the same maximum sampling frequency. You will only need to worry if your program was out analog.

    When you install a sinlge on a pc data acquisition card, MAX lists it as dev1. If you do the same thing with a different DAQ card on another pc, it is listed here as dev1. As I said, there is no difference to explain.

  • Connecting two cisco ESW 500 series switches.

    Hi Experts,

    I have a basic knowledge of the network and need help.

    I have two switches cisco ESW 500 series and I want to connect with each other.

    Q1 # what type of cable should I use to connect these two CrossOver switches or fiber... What is the advantage of the use of fiber on CrossOver. ?

    Q2 # what are the ports marked in the image used to...?

    Hi tech spec.

    You can use copper or fiber. You can use directly through crossover is not necessary. Fiber is generally more reliable, can offer a higher flow and distances much longer if needed. You will need to buy SFP modules to connect the fiber switches, which is an added expense.

    The ports on the right are shared. If you plug a FPS in the far-right for the fiber port, then the port to the left of it becomes idle. Only port copper or SFP port can be used at the same time. In addition, these ports are usually used for the uplink to another switch or router.

    Please mark this thread as answer or reply if you have any additional questions.

    -Marty

Maybe you are looking for

  • Access Game Center

    My son wants to access his account of clan on my wife for my iPad iPad. When I go to his Apple ID on my iPad, I can get to the confrontation of the game clan, but then he says: I'll lose all the progress of my shock of game clan. These means my progr

  • increment of voltage

    Hello world I have a question I think that it is really easy to solve, but I can't find a way to do this. I need to apply a voltage across a sample. I would like to increase this voltage of 100V every 30 s. For the moment, just trying to find a simpl

  • My Windows Live Toolbar has suddenly stop working. When I click on anything, it is that the page cannot be displayed.

    No problems with this toolbar until yesterday. Now, I click on mail-page cannot be displayed. Click on profile-page can not be displayed. That's happened?

  • Windows Vista - Windows Mail - creation of Contacts Group__

    Trying to create a group of Contacts.  Help says -Opening of Contacts-On the toolbar, select new group of Contacts - BUT THERE IS NO SUCHOPTION - HELP!

  • Issue of notification led several

    Hello I would like to ask if is it possible to alternate the color when you have several notifications. I noticed that when I get two different notifications with different colors of light just flickers with a single color. Thank you.