syslogging to 2 host with different levels of severity?

Similar Questions

• vMotion between two hosts with different version?

  
  Hello

  Can I vMotion VM between two hosts with different version? For example, a virtual machine of esxi 6.0 5.5 esxi and esxi esxi 6.0 5.5 vMotion.

  Thank you.

  Yes, it will avoid you to move.

• vMotion (without shared storage) between two hosts with different vSwitches standard s VM

  I can VM vMotion (without shared storage) between two hosts with different vSwitches standard? The vSwitches on these two hosts have different names and number of NIC, but have the same name of portgroup.

  
  Thank you.

  Yes, you can in a Storage VMotion to one Esxi to another with no shared storage...

  It is important the portgroup bears the same name... This is the reference for the VM...

• VMotion between 2 Hosts with different processors

  Hallo,

  I have a server in my homelab I use for studies of VMsphere and I want to get a second machine to test advanced features such as HA, Vmotion etc.

  My first server has a map of X9SCM-9 with processor Xeon E3-1230V2 (Ivy Bridge). I am currently running ESX 5.0 U2 on it.

  I was counting on obtaining of material quality for the second host consumers because I don't want to spend a lot on it, so I thought that I need any CPU generation Ivy Bridge.

  I tested today with a second machine with a Pentium G2020 Ivy Bridge, but when I try to Vmotion he says "the virtual machine requires physical features that are not available or disabled on the host... ».

  So I figure there must be a difference in architecture regardless of the CPU beeing an Ivy Bridge CPU.

  When I try to activate CVS it just me are going to the 'Nehalem' Version so my virtual machines running on host 1 would not be able to use all the features of the CPU since the Xeon.

  So the question boils down to: what is the processor less which offer compatibility VCA L5?

  Or is there something else to consider in VMotion between two hosts with different processors?

  I got a shared storage, etc. of the same network configuration.

  Thank you

  Benjamin

  Hi Benjamin,

  For compatibility VCA L5 want to look at one of the following models, Intel CPU:

  • Ivy Bridge: Series E3-1200-v2
  • HASWELL

  I would recommend mental health that before rushing and a CPU purchase, check if a cheaper option would be, as Jon mentions in suppresss some fo the CPU compatibility checks so obviously, this is not desirable in a production environment, and must be applied in your study of VMware Lab to the home address.

  Hope this helps,

  Simon

  TechHead

  http://techhead.co

• How can I add a donation page with different levels to give for example $ 250, $150, $50, other

  How can I add a donation page with different levels to give for example $ 250, $150, $50, other.  I'm with Foxy cart... is it possible?

  Since the end of the Muse, you can add texts as the value of the donation with paypal button that would take users to the paypal for the payment site, with Foxy cart you can try the suggestion mentioned here:

  https://Forum.FoxyCart.com/discussion/4417/donation-page-radio-button/P1

  Thank you

  Sanjit

• I'm looking for a simple list of available applications with different levels of creative cloud subscriptions?

  Boy, the Adobe web site is incredibly frustrating. It is very difficult to accomplish some very simple tasks. First of all, there should be an email address for contact. I shouldn't be forced to submit my question on a forum. It's cheap and lazy on the part of Adobe, especially when they charge a lot for their subscription applications.

  My biggest complaint is that I can't find a simple list of the applications available with the cloud creative in different subscription levels. When I search, it sends me to a video of slick 'overview' of the creative cloud which tells me zero in on specific applications available. It should be a simple list of available with creative cloud applications and a side-by-side comparison of the applications available with the different levels of subscription creative cloud. Why can't I find something like this on the web site of Adobe? I found a page that lists 15 adobe applications, but not a page that describes to me what apps come with what levels of creative cloud subscriptions.

  There are only 3 shots of cloud. Inclusions are the same for both commercial or student.

  All applications

  Desktop: desktop applications Adobe Creative Cloud | Adobe Creative Cloud

  Mobile applications: Adobe mobile, iPhone, iPad, Android apps | Adobe Creative Cloud

  Same info differently formatted: Adobe CC 2015 Direct Download Links: Creative Cloud 2015 Release | ProDesignTools

  Plan of photography: Photoshop + Lightroom

  Single App plans (applications available for the unique implementation plans are in the drop-down menu on the page of the plans of cloud)

  Pricing plans and creative Cloud membership | Adobe Creative Cloud

• Update a field with different values of several tables

  Hello
  
  I have a table named AAA with 2 fields id and structure.
  And then I have other 3 tables with 2 fields id1 and structure1 id2, table1 and table2, id3 and structure3 to table3 organized.2.
  
  The number of AAA id is equal to the sum of the IDS of table1, table2, table3: #id = #id1 + id2 # + #id3).
  
  I want to update the structure of AAA table with values as well as field:
  where AAA.id = table1.id1-> AAA.structure = table1.structure1
  where AAA.id = table2.id2-> AAA.structure = table2.structure2
  where AAA.id = table3.id3-> AAA.structure = table3.structure3
  
  Can someone help me?
  
  I have Oracle11gR2.
  
  Thank you in advance.

  Oops...

  update  AAA
  set structure = (select structure1 from table1 where aaa.id = table1.id1)
  where aaa.id in (select id1 from table1)
  

• Stop reboot request when fast vMotioning to a host with a different processor

  I need help to find a better way to deal with a prompt to reboot my users get due to a vDesktop in model (Dell 710) host vMotioned to another (Dell 720). The difference between the two is the processor models. The 710 is a Xeon X 5670 and the 720 is a Xeon E5-2667. The two processors use the same .inf (cpu.inf) file and apparently the drivers. Simply, it triggers the installation process of the material causing the Plug and Play Manager to require a restart of the operating system after the installation. The result, I'm wanting just needs that this reboot window displays don't not weither would it by slaughtering the hardware installation process, hide the window of dialogue itself, or any other possible way to configure the system which does not show users. I've confirmed that you don't have to restart the machine remain operational. Here is some additional information on the operating system and all.

  Windows 7 32 bit

  1 vCPU

  2G of RAM

  vSphere 5.0.0 623860

  Discover Constable's 5.0.0 481677

  Any suggestions or thoughts are greatly appreciated.

  Tanner

  I encountered the same problem and the only solution I've found so far is to start the master on both hosts.  When he started on the two hosts, the message no longer appears when moving the virtual machine back to a host with a different model of CPU.  I have two clusters currently, so I have not tested vMotioning fast machine between hosts with different CPU while it is running.  When I had the chance to test, I'll post my results.

  -Chris

• How can I erase different levels of opacity of a color?

  I was thumbnail sketches using the Brush tool, in a single color (black) with different levels of opacity for the shading. I had milked on a single layer and on the other, but accidentally shaded shading on the line drawing and can no longer cancel/step back. I need to delete/remove shading and keep the intact black line drawing, but the PS does not seem be able to differentiate between the different levels of opacity and treats as a single colour when I try to use the erase special as Magic Eraser no matter how high I set the tolerance or selection tools, etc.. It's a simple sketch and I could draw it again, but I'm very rusty with PS and I would like to know if there is a solution in case I met this new. Prescheduled A below. Suggestions?

  

  Part three fix

  Levels adjustment layer and drag the slider of Pentecost slowly to the left.  This will gradually move the nuances that darkens the white full.  Move the black slider until it is in the fleshy part of the shadows (black) and adjust the slider to the Middle for the best effect.  You will fix with this step.  Just do a lot better.

  NOTE: you must change the blend mode of layer of brightness levels.

  I'd be inclined to remove all the colors of the image as well.  (Hue saturation, B & W adjustment layer, but do not change gray scale)

  Now select the layer levels and do a layer of copy merged top Ctrl Alt Shift (Shift Cmd Opt e) e

  Now select the brush, and then change the brush in overlay blending mode (in the options bar)

  Carefully paint on the black lines with black to strengthen and shading with white to remove it.  Need you a bit of practice.

  It took me about two minutes.  Another ten and you'll have it right, (assuming that the original is a higher resolution)

  

• Best way to migrate virtual machines to new ESXi hosts with a different configuration of networking.

  We currently have a cluster of 6 Dell machines that move VM 120 or so on ESXi 5.5. Networking consists of a dVswitch with 6 uplinks that map to 6 x 1gig physical NETWORK adapters on each host ESXi... These are grouped into 3 trunks / gal, so we have 2 GB by SHIFTING of the bandwidth and failover. The LAGS are configured as follows:

  LAG1

  Traffic to our (NFS) shared data store and management of ESXi. (vmk0)

  LAG2

  Access to the network of the VM - groups of different ports on different VLANS

  LAG3

  vMotion (vmk1)

  We just bought 6 new Dell machines that have connections fiber 2 x 10gig each. The idea is to bring together in a 20Ggig LAG by machine that will handle all of the traffic, so traffic NFS data store, network traffic from the VM, vMotion and traffic management ESXi.

  
  

  What is the best way to migrate the virtual machine in the cluster existing to the new machines? Many of the virtual machine are essential, so we cannot stop time.

  
  

  Can I create the new DELAY on existing dVswitch and put it as an auxiliary card? I'll be able to do it for all 3 of the above both above LAGS?

  
  

  Thanks for the info Alistar, it's almost here. The bit that was me stumping was that after establishing a new dVswitch I received messages that the new dvSwitch was not reachable on the old host, when I tried to migrate the virtual computer.

  The solution (with the permission of VMware Support) was that I need to add the two dVswitches to one of the old hosts, then assign a physical alternative on this host uplink to a temporary 3 uplink on the new dVswitch. I then tag all the relevant VLAN that uplink.

  This way I can first migrate the virtual machine to the new dVswitch networking so I can move the computer to the new cluster.

  Obviously I can only migrate from old to new cluster with a single host. each virtual machine must be a double for the host with 2 switches, and then to the new cluster. I also had to have the two dVswitches to the same version.

  Fortunately, I had a physical rising spare on the hosts of the old, otherwise I would have had to break one of the trunks and re-use of one of these uplinks.

  Oh and be aware, impossible to use the same names for groups of ports 2 DV switches, they must be unique!

  Nick

• Can we do vmotion between hosts with load balancing in network cards grouping different strategy.

  Hello

  We are implementin new host in our Infra and do some vmotions between different groups. A group a host with balancing 'route based on IP hash. " Can we do Vmotion to another cluster where the hosts have different load balancing policies. In addition, if we change the policy on new hosts in furture of load balancing is loss of downtime or a package?

  Kind regards

  Vikram Kumar

  First of all, no problem from VMs one ESX to another, they use different political Multipathing.

  Second, if you use IP hash, it means you are using etherchannel (or LACP) on the physical layer - configuration/cancellation of the configuration that almost always require that the uplinks are not used by any VMs, so you have time to synchronize the physical and virtual configuration. It is not a time out, but you need to plan accordingly - all depends on your physical network capacity.

• Cluster with different host - resource pools hardware?

  Hello

  We have currently three generations of servers at base of AMD in our environment - with different CPU clock speeds.

  Guests are split into three groups and VMs are grouped based on clock speed.

  But frankly, it's a mess to administer.

  We envisage the creation of a single cluster and using pools of resources.

  But CPU resource pools take host speed of the CPU in return?

  - Or they just sure that VMs receive their share of CPU temps on loan-time partial?

  Best regards

  Martin

  Pools of resources sharing works only when there is some conflict of resources.

  -VMs in 'high' will appear on hosts with fast processors? - and get the most MHz?

  The actions are only priority... Then no.

  With a reservation... it depends on how much MHz offers...

  - Or they simply receive a high share of CPU time on a random host?

  By shars Yes...

  But remember the first sentence!

  If you have enough of free resources, all virtual machines are also (for actions).

  André

• Restore the virtual hard drive backup on a different node with different IP and host name.

  Hi guys,.
  I want to do the following.
  
  My reliable backup strategy is the virtual hard drive backup. The database is installed on a virtual particulay machine (node). Now, I do not take the backup of the DBF files or control files or files from archive.
  I rely on the virtual hard disk backup. It takes the entire Virtual Machine backup. Now, I wanted to restore this virtual hard drive backup to a different node with different IP and host name.
  But before I start the database, there are some things I need to do.
  As change address IP address and the hostname registered with the database installed and its services.
  
  Please guide me through the steps on how to perform the activity.
  
  Concerning
  Lam...
  SOA admin.

  I think that the whole operating system will be restored in a new virtual machine... I have it... The changes will have to be done in the file listener.ora (hostname or IPADDRESS and also PORT NO in case you want another port as the existing one). Once you have made the changes that you have to bounce the listener, I mean stop and start the listener... I don't think that any other changes are needed... Make sure that the same need for entries (from the listener) to be included in the TNSNAMES file. ORA file both client-side... The tns service is used to connect to the remote database server (from the demand side or whatever source you used to connect to the database server)... I just think that the change to do... Hope its clear... Please try...

  HTH
  Kind regards

  IMRAN KHAN

• Duplication duplicate a database with RMAN, different host database different withou

  Hello
  
  I want to duplicate a database with RMAN, different host, a different database without RMAN Duplicate Technic.
  
  I HOST1 with a database DB1 and
  HOST2 with a DB2 database
  
  I have a complete backup of the DB1 in host HOST2. How can I use this backup to clone the database?
  
  Thank you

  see the links: -.
  http://kamranagayev.WordPress.com/2010/03/29/RMAN-video-tutorial-series-performing-disaster-recovery-with-RMAN/ (Video Tutorial)
  http://oracleinstance.blogspot.com/2010/08/disaster-recovery-using-RMAN-demo.html
  http://gavinsoorma.com/recovery-scenarios/

• Comparison of column level with different database to different server

  Hi all
  
  
  I have two database on the other server. I want to find the difference between the tables in the two tables for example same table with different column, it can happen...
  
  
  How to compare two tables column level with two differnet Server database.
  
  
  
  Thanks in advance.

  user647572 wrote:
  Hi all

  I have two database on the other server. I want to find the difference between the tables in the two tables for example same table with different column, it can happen...

  How to compare two tables column level with two differnet Server database.

  SELECT * FROM USER_TAB_COLUMNS
  LESS
  SELECT * FROM USER_TAB_COLUMNS@REMOTE
  UNION
  SELECT * FROM USER_TAB_COLUMNS@REMOTE
  LESS
  SELECT * FROM USER_TAB_COLUMNS;