System repair disc does not work in repairing, it comes back indicating that the version of ERD is not compatible.

Similar Questions

• Vista does not start, fails to Startup Repair indicating that the version of the operating system is incompatible with Startup Repair tool

  I use a laptop Dell XPS M1330, under Vista Home Premium 32 Bit. The laptop froze, I tried to do a system restore, which did not work. Now the laptop goes into startup each time put on repair. A message window appears saying "Startup Repair cannot repair the computer automatically. Startup Repair window says "Startup Repair could not detect a problem. Diagnostics details say: Root cause found: the operating system version is incompatible with Startup Repair tool.

  I tried to use the Dell Factory Image Restore to restore the system, but it does not end. I get an error message instead. There is no details, it's just a small window with an X and the Word error.

  I also tried to use resettlement Dell DVD, but that doesn't seem to work either.

  Vista does not start at all, not in either safe mode.

  I just ran to the Dell Diagnostics tool, and that is to say that the integrity test of memory has failed... No idea how to solve this problem?

  I'm at a loss and helps woukld be appreciated.

  Hi James,

  Ø are you using the correct version of the Vista disc to run Startup Repair?

  I suggest to run the diagnostic tool memory WINRE mode and check if the memory (RAM) installed on the computer works fine.

  Follow the steps below to start the computer using the WINRE and run the memory diagnostic tool.

  A. Insert the Windows Vista installation disc.

  B. restart your computer.

  C. Si you are prompted, press any key to start Windows from the installation disc.

  Note: If your computer is not configured to start from a CD or a DVD, see the documentation provided with your computer. You may need to change your computer's BIOS settings. For more information, see BIOS: frequently asked questions.

  D. choose your language settings, and then click Next.

  E. click on repair your computer.

  F. Select the operating system you want to repair, and then click Next.

  G. in the menu system, SelectMemory diagnostic tool Recovery Options.

  Once scanning is complete, check to see if the problem is resolved.

  Access the link below to learn more about Windows recovery options in Windows Vista.

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

  http://Windows.Microsoft.com/en-us/Windows-Vista/how-do-I-know-if-my-computer-has-a-memory-problem

  If you have several sticks of RAM installed on the computer, you can try to remove one of the RAM stick and check if it works very well. Also, you try to exchange the RAM sticks and check if one of the RAM is originally this issue and if it needs to be replaced.

  Note: If you are not aware of the evolution and swaping the stick of RAM on the computer, it is best to contact the computer manufacturer for help on this and you can do it at your own risk.

  You can also contact Dell support and check if you need to replace any hardware.

  I hope this helps. Let us know the results.

  Thank you and best regards,

   

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Re: Satellite L300 - made recovery but disc does not work

  I have a Satellite L300 and did a few sets of recovery discs from what I read some brands work and some don't, and none have so far.

  Insert Diskette 1, press the button and hold F12 key until the startup option appears.
  Select CD/DVD and then back type box appears with X:\windows\system32\cmd.exe - startnet.cmd
  and in the box waiting for ODD vacancies...

  You can add several points after that as nothing is more - so three sets of recovery disks on three different brands of DVD any advice would be pleaseing!

  Brian

  Hello

  According to your description, the system restore procedure does not start, and the STRANGE can not read the disc.

  In your case I would recommend recover laptop using Toshiba HDD recovery.
  You can start the procedure of HARD drive; Press F8, choose repair my computer, Toshiba HDD recovery.
  Now the system restore should products

  After the laptop has been set to factory settings, check to see if there is an update of firmware for this CURIOUS (CD/DVD drive). If yes-> update the firmware.
  I know you tried three different brands of DVD but you should always try to create a recovery disk using another DVD disc I m using TDK DVD-R and had good experience with it. One of my friends uses Verbatim DVD-R and never had problems

• cooling fan (fan system 90 b) does not work

  cooling fan (fan system 90 b) does not work for my laptop of 2229 you pavilion g6, my warranty period is not over, what is now a solution for this?

  Try a hard reset as follows:
  
  (1) remove the battery and unplug the DC power adapter.
  (2) press and hold the power button for more than 15 seconds.
  (3) plug the DC power adapter (leave the battery for now)
  4) press the power button
  
  Please post here your positives or negatives in your thread. If that does not improve the situation, thencontact HPfor warranty repair service for your laptop.

  Troubleshooting here

• Microsoft Flight Simulator 2004 installation with the 4th vista disc does not work. What should I do?

  Microsoft Flight Simulator 2004 installation with the 4th vista disc does not work.  What should I do?

  Hello

  You get no matter what error code or error message?

  There seems to be a problem with the file missing in the rear disc system. I suggest you to refer to the following Microsoft article and check if it helps.

  Flight Simulator 2004: known video issues: http://support.microsoft.com/kb/823628

  If the steps in the Microsoft article mentioned above do not help, then it would be best to ask your question in the Microsoft Game support forum.

  Microsoft Flight Simulator Games Forum: http://www.fsinsider.com/

  Or contact support for Microsoft Flight Simulator game: http://www.microsoft.com/Products/Games/FSInsider/tips/Pages/default.aspx

  Hope the information is useful.

• BOOTMGR is missing. Get the message "this version of the system recovery options is not compatible with the version that you want to repair...» »

  Two days to try to solve this problem of complete.  Vista Home Premium (64-bit) has been installed more than 6 months ago.  With the legal copy in the computer, I can choose the repair, it shows me me partition Windows Vista Home Premium.  I don't get the system recovery options, but I get a window that says «the version of the system recovery options is not compatible with the version of windows that you want to repair...» ». I loaded the original drivers for the motherboard.  I started in safe mode, and I can see the different folders.  It tells me that everything is there. Does anyone have a solution for this? I use a product called '360 °' for regular backups, but backups are on a network drive.

  Thanks for the suggestions!

  Here is a link to some people who had the same problem and solved: http://keznews.com/forum/viewtopic.php?f=2&t=20665.  It seems to have something to do with the help of a record of 32-bit with 64-bit recovery (or something of the sort).

  I hope this helps.  Good luck! Lorien - a - MCSE/MCSA/network + / A +.

• my work of collapsed app coil system, help printer does not work

  my work of collapsed app coil system, help printer does not work

  Hello

  1. What is the brand and model of the printer?

  2. do you have an error message when you try to print?

  3. were there any changes (hardware or software) to the computer before the show?

  Perform the steps suggested by chan seen from the link below and see if it helps.

  http://social.technet.Microsoft.com/forums/en/itprovistaprinting/thread/460f297a-dd66-4476-A176-542e1519ca3e

  Hope this information helps.

• All of a sudden my system aero theme does not work!

  All of a sudden my system aero theme does not work! Before that it worked. But it doesn't now. What should do?

  Original title: aero theme!

  Open the Aero Troubleshooter by clicking the start , and then clicking Control Panel. In the search box, typeTroubleshooter, click on resolution of problems and then, under appearance and personalization, click Display Aero desktop effects.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

• You will need to re - install Creative Suite 5 to my computer after my laptop crashed. But the disc does not work.

  Hi all

  Please help me!

  My Creative Suite 5 installation disc does not work. What can I do?

  RD

  If you follow the 7 steps, you can dl a trial through one of the links on this page: http://prodesigntools.com/all-adobe-cs5-direct-download-links.html

  and activate it with your serial number.

  If you have a problem with dl, you don't follow all 7 steps.  as a general rule, do not carefully follow the steps 1, 2 or 3 is the problem.

• the system recovery media does not support this computer

  I have a HP G7-1365DX and the hard drive (750 GB) is a failure.  I did a recovery file on a USB key from the recovery partition and then replaced the hard drive with a 120 GB SSD.  When I tried to reinstall the USB system, I get the message "the system recovery media does not support this computer."  Is it because the hard drive was replaced by a SSD?  How to restore the system if the recovery disk does not work?

  Hello

  You are right about the source of this problem - HP recovery media often has problems of restoring the operating system on a smaller disk in quality than appeared on.

  There are a few options available.

  1. if the 750 GB drive is still able to operate, use your recovery media to perform a factory reset and then use software (or Windows 7 own imaging utility) for this clone of your SSD.

  2 create your own recovery media to use to run the installation - it would be my personal preference.

  Before you try the following, make sure that you can always read the character product activation key 25 on your label Windows COA (5 blocks of 5 alphanumeric games).

  An example of a COA label can be seen here.

  You can create an installation disk yourself using another PC - just download the good Disk Image ( this must be the version exact same origin supplied with your laptop ) from the link below and use an app like ImgBurn to burn the ISO correctly on a blank DVD - a guide on the use of ImgBurn to write that an ISO on a disc is here.  These Images are clean and a well respected source, however there are only limited versions available.

  Windows 7 sp1-iso-official-32-bit-and-64-bit

  Use the disk to perform the installation, enter the activation key of Windows on the label of the COA at the request and once the installation is complete, use ' 'phone Method' described in detail in the link below to activate the operating system -this made method supported by Microsoft and is popular with people who want to just have a new installation of Windows 7 without additional software load normally comes with OEM installations.

  http://www.kodyaz.com/articles/how-to-activate-Windows-7-by-phone.aspx

  All pilots additional and the software, you may need can be found here.

  Kind regards

  DP - K

• System - F10 recovery does not

  Hello.

  I tried to fix a HP Media Center M7380.

  The XP operating system was damaged during an update of the operating system, it could not start and has been reset permanently.

  At first, I was able to access Recovery Center through F10, but didn't try it until I got a decent backup of the data on the disk.

  Now that I managed to backup of the C: drive, the F10 boot option no longer works, it shows just a black screen.

  The HP Recovery partition is intact, how to create a recovery disc without the installed XP and without the F10 at startup?

  Thanks for your suggestions.

  Dave...

  I SOLVED THE PROBLEM, recovery is much better than I hoped.  I will update this thread in hopes that I can be useful to someone else.

  I tried many suggestions provided by the HP site, Google, "10 things to do when Windows XP does not start" et al., without any hope of success.

  With the help of the "Hirens boot disk" I finally discovered that some vital XP files were missing from Windows.  I think that the owner of the computer (a friend) may have attempted to install the software or update the system when it crashed, but I don't have the details of exactly what has been done.

  -The PC would not boot in any mode.

  -The recovery disk provided was for a completely different PC and a different version of windows

  -J' tried to start the recovery console from another drive to install XP, but the recovery was not a permitted option

  After careful consideration and several other solutions attempted, the following managed.

  1 - use the Hirens boot disk to start MiniXP.

  2 - Open a command line.

  3. type C:

  -Press enter

  4 - Type cd windows

  -Press enter

  5 - type "CD Creator.exe" that must be typed with the quotes and space

  -Press enter

  At this point, that an application window for recovery disc creator appeared, option buttons are strangely absent, but I used the key entry instead.

  I was prompted to select 11 CDs or 2 DVDs, I went for 2 DVD

  Two hours (approximately) later I had the necessary recovery discs

  I opted for a recovery of the system rather than the Format and reinstall.

  It completed successfully.

  I made sure that the version of Norton AV trial provided worked.

  I have indication internet, downloaded and installed XP SP3 and all other updates of the system.

  User data (photos, documents, etc. was recovered by)

  -Rename each individual user folder in "C: Documents and Settings" to (for example) Dave143 to Dave143SAVE

  -Creation of the user of the control panel.

  -Login under the user to build (Dave143) user folder "C: Documents and settings".

  -Restart in safe mode and copy the data from the Dave143SAVE folder folders in the Dave143 folder.

  It took me all night for a week, but now I'm happy with the result.  I managed to save several gigabyte of their family photos!

  Don't forget, before you try anything at all, your first priority should be the backup of data.

  Good luck!

  Dave...

  Message edited by Dave143 on 06/11/2009 14:11

• T420 W7 Base system device driver does not

  Hello

  After reinstalling W7 the lenovo Solution Center complained by saying that the system device driver does not work.

  I saw that the SD card reader was not working and so I covered the missing pilot was that one.

  The Lenovo page I downloaded the driver for the card Multi for W7 and T420 port. After installing the message disappeared and SD cards have been recognized correctly.

  However, after restarting the system, after some time, the message appeared again and the card reader no longer works.

  I have install again and the same happened. He worked and after restarting two has stopped working.

  If find this mysterious altogether. I wonder if anyone knows how to solve this problem.

  I managed to solve the problem. Just in case anyone has the same problem I explain here how I did, although I'm not sure that this solution is universal.

  1 install the drivers from the Lenovo site.

  2. once the system starts to complain from the Device Manager where it says "Base system device" with a question mark. Then disable this device but do not uninstall the driver.

  3 reboot and it will be fixed.

• ENVY 15 3040 nr recovery disc does not

  Hello

  I made a recovery disk set as soon as I bought my ENVY 15. I accidentally deleted all partitions, then tried to recover by using the disks that I did... but I get this error by...

  The system recovery media does not support this computer.

  You are not able to restore the system with the media.

  0110 A9P60UA #ABA - A9P58UA #ABA

  Help, please!

  Hello

  Assuming that it's just a problem with the recovery media, here's another solution, you can try.

  Before you try the following, make sure that you can always read the character product activation key 25 on your label Windows COA (5 blocks of 5 alphanumeric games).

  An example of a COA label can be seen here.

  You can create an installation disk yourself using another PC - just download the good Disk Image ( this must be the version exact same origin supplied with your laptop ) from the link below and use an app like ImgBurn to burn the ISO correctly on a blank DVD - a guide on the use of ImgBurn to write that an ISO on a disc is here.  These Images are clean and a well respected source, however there are only limited versions available.

  Windows 7 sp1-iso-official-32-bit-and-64-bit

  Use the disk to perform the installation, enter the activation key of Windows on the label of the COA at the request and once the installation is complete, use ' 'phone Method' described in detail in the link below to activate the operating system -this made method supported by Microsoft and is popular with people who want to just have a new installation of Windows 7 without additional software load normally comes with OEM installations.

  http://www.kodyaz.com/articles/how-to-activate-Windows-7-by-phone.aspx

  All pilots additional and the software, you may need can be found here.

  Kind regards

  DP - K

• Photoshop 5.5 installation disc does not load

  A virus ate my office and I had to reboot Photoshop. Photoshop 5.5 installation disc does not load. Any ideas?

  You can download the demo version of the software through the page linked below and then use your current serial number to activate it.

  Don't forget to follow the steps described in the Note: very important article Instructions on the pages to download to this site or the download may not work properly.

  CS5.5: http://prodesigntools.com/adobe-cs5-5-direct-download-links.html

• Apple dvd player will not eject a disc, does not show in the devices

  I'm on El Capitan, the player has played other discs, this disc does not appear

  There is no manual of the dvd drive eject

  drive does not appear in the devices

  Get help with the SuperDrive slot on your Mac - Apple Support loading

  How the disk by force ejecting

  Mac Mini

  How to eject a defective DVD?