System repair of Windows XP Embedded without the help of his CDs?

I use a CCTV using the Windows XP Embedded platform. Recently, due to some problems, I'm not able to boot the system and that's what suggests to repair windows using the CD because of the missing "C:\WINDOWS\SYSTEM32\CONFIG\SYSTEM" file I have lost my CD of Windows XP Embedded, but I have original Windows XP CD. Can I use the Windows XP CD and repair system?

For this error, always start with a chkdsk/r from the XP Recovery Console.

The question was preceded by a loss of power, aborted reboot or abnormal termination? (This includes the plug pulling, buttons power and removing the battery).

These can cause corruption in the file system that must be fixed before you do anything else.

If none of these events occurred (or even if they have not taken place), you must verify the integrity of your file system before anything else (especially "try" things).

There is zero logic to begin to try to begin to try to modify or copy files to a hard drive that has a corrupted file system, so this must first be fixed using the XP chkdsk program and run chkdsk on your hard drives may solve your problem completely.

Use the XP Recovery Console to check the file system on your HARD drive and fix the problems and then try to start your system - this may be all you need to do.  Or, you are welcome to just start trying things that might work.

Boot into the Recovery Console Windows using an XP bootable installation CD.

If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and don't forget (no support for XP not necessary).

This is not the same as recovery disks that might have come with the acquisition of the system store.

You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

The ISO bootable image file you need to download is called:

xp_rec_con. ISO

Download the ISO from here:

http://www.mediafire.com/?ueyyzfymmig

Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

http://www.ImgBurn.com/

When you install ImgBurn, DO NOT install the Ask toolbar.

Here are some instructions for ImgBurn:

http://Forum.ImgBurn.com/index.php?showtopic=61

It would be a good idea to test your bootable CD on a computer running.

You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

When you start on the CD, follow the instructions:

Press any key to boot from CD...

Installing Windows... going to pronounce.

Press 'R' to enter the Recovery Console.

Select the installation that you want to access (usually 1: C:\WINDOWS)

You may be asked to enter the password (usually empty).

You should be in the folder C:\WINDOWS.  It's the same as the

C:\Windows folder that you see in Solution Explorer.

The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

Assuming your boot drive is C, run the following command:

CHKDSK C: /r

Let chkdsk finish to correct the problems, he could find.

It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

You must run chkdsk/r again until it finds no error to correct.

Remove the CD, and then type "exit" to exit the RC and restart the computer.

You have not to set the BIOS to boot the disk HARD since the CD won't be.

Tags: Windows

Similar Questions

  • EliteBook 8570w system repair disc Windows 7

    Hi all

    I wanted to do a repair disc Windows on my Elitebook 8570w system. It's pretty easy because Hp has a program called Hp Recovery Disc Creator that accomplishes this task for you. It gives you a possibility to burn a Windows disc and a driver disc. What HP calls the Windows disk is the system repair disc.

    Now, my problem is that the Windows disk does not work correctly (no idea why). When booting from the DVD screen guard stuck to Windows is loading files... Also when I try to run the installer from the DVD, I get error messages that says 'F:\Sources\autorun.dll is not designed to run on Windows or it contains an error.' and after 'the file 'autorun.dll' could not be loaded or is corrupt. Setup cannot continue. Error code is [0xC1]"because I had all of a sudden to make the drive I can't simply make another DVD.

    Then, I tried to let Windows do the repair system itself disc (help to create a system repair disc). However, I get a different error message: "the parameter is incorrect (0 x 80070057).» Some people suggest that HP Recovery Disc Creator has "hijacked" the function "Create a system repair disc" window and this is what causes the problem. If HP does not give me a second try, and it prevents Windows to give me a second try as well! Then, perhaps to remove HP Recovery Disc Creator would work. However, it does not list in programs and features and I can not find an uninstall file in its directory.

    When you try to find a solution I came across a guide to create a boot Windows 7 Installation USB drive (http://www.sevenforums.com/tutorials/2432-usb-windows-7-installation-key-drive-create.html). She is to copy the files from the installation of the USB disk. Step 21 details the files that are on the installation disc. They are the same as on my system repair disc.

    Download an image of the installation disk so the same as downloading an image of the system repair disc? (I download an atm file but don't know if that makes sense) If not, are there other options to create a new system repair disc? Maybe somehow Uninstall HP Recovery Disc Creator or he fool into thinking I have not yet tried to do a Windows disc? Where can I download a disk image of the repair system somewhere online (I found most of the links are dead)?

    Please let me know if additional information is required! Thanks in advance!

    Michael

    TLDR: burned a disc repair system, the disk is not working properly, HP and Windows will not let me try to burn again. Other options?

    Hello:

    You can probably make an ISO file of the version of W7 Pro you must go to the link below.

    Use the SP1 media files regenerate.

    http://forums.mydigitallife.info/threads/14709-Windows-7-Digital-River-direct-links-multiple-languages-x86-amp-x64/page59?p=470600&viewfull=1#post470600

    Use the W7 Pro from the bottom of the laptop product key to activate the installation.

    This tool allows to transfer the ISO to a flash DRIVE or a DVD drive.  The tool also performs the bootable file.

    http://www.microsoftstore.com/store/msusa/HTML/pbPage.Help_Win7_usbdvd_dwnTool

    Your other option would be to order a series of W7 for your PC recovery discs, by contacting HP for the country that you live in the link below.

    http://WWW8.HP.com/us/en/contact-HP/WW-contact-us.html

  • How Downgrade of El Capitan in Yosemite without data loss and without the help of a Time Machine?

    I, are looking for an answer to this question, but couldn't find one.  If there is an and missed it, please tell me and I will look happily on it.  I want to do it without the help of a Time Machine, because I used it at the time of Yosemite.  And I discovered that you can use a cable USB or SD to come down, but how do you do this without losing all my data?

    You must save, erase the drive, install Yosemite, restore your backup of the data

  • How to create a box the size of the artboard without the help of a script

    HI -.

    Is there a way to create a box to the size of the artboard automatically, without the help of a script? FOR EXAMPLE. something I can build in action. Ive been able to create the box using a script, but we can not save the script in action, so unfortunately that there's no help for me

    What I want to do is

    1 open the file

    2 create box with no filling, no race, making the size of the box of the artboard

    3. run the rest of an existing action

    Greatly appreciate any help, I want to run on more than 10,000 cases per year.

    Using slices may be slightly inaccurate, Carlos (no offense intended).

    Here is another approach:

    Rectangle_Artboard_Size.AIA - Google Drive

    The action was created in Illustrator CS5, so no guarantee that it works in CC2015.

    Two prerequisites are necessary:

    -Alignment on work plan should be on (pallet alignment).

    -L'option divide and outline will remove unpainted work should be disabled (see Options Pathfinder).

    In older versions of Illustrator (I think of CS3), we could make a simple gesture of the 2 step using the object > acreage > make order, then the cultivated area > Release. It is not possible in recent versions of Illustrator.

  • When I try to create a system image in Windows 7, I get the error 0x8078002A and 0x8007045D code

    I'm using Windows 7 Ultimate 64 bit and try to create a system image on my 3 TB USB 3.0 Seagate Expansion. A few seconds after the start, the backup fails and displays the message:

    The backup failed.

    One of the files of backup could not be created. (0x8078002A)

    Additional information:
    The request could not be performed because of an i/o device error. (0x8007045D)

    I tried to create a system image to multiple computers, which results in the same error codes. I reformatted the disk and run chkdsk, but to no avail. If anyone has any ideas they would be greatly appreciated.

    I suggest avoid you the Windows backup program and you get a good commercial backup program. This forum is frought with for a windows problem reports. I know that I was very impressed when I tried it. Two me are familiar with and like Norton Ghost (which I use for 7 years without the 1st problem) and Memeo, which has 30 day free trial and you can buy it for $29.99 - you can download it from http://memeo.com. You can get Ghost for almost nothing (like me), if you look at the sales.

    CNET has a lot of reviews of backup program to

    http://download.CNET.com/Windows/backup-software/?tag=contentBody;sideBar

    .

    Some of them are free (the last time I checked there over 300), some have free trials (more), and some are buying only (more than 200).

    Good luck

  • Install the latest Firefox on Windows XP Embedded gives the error: "this application has failed to start because pdh.dll not found."

    I try to install the latest browser (normalized), sure I can the old computer of Windows XP Embedded. Hardware does not meet the 'recommended material' a Pentium 4 (it has a P3). I tried at first installation/bar of Firefox version 28, and that seemed to work well. Version 36 gives error that I said in the question. It is not essential that I run the * last * version of Firefox (the browser is ONLY used for an intranet application), but I would like to install the latest version that will work, and if there is a simple solution for this version, I want to explore that.

    Kind regards

     Gerrat
    

    Hi gerrat, it is probably best to use the version of esr firefox 31 in your case: https://www.mozilla.org/en-US/firefox/organizations/

  • How to install "Additional language supported" in Windows XP SP3 without the CD?

    I have a valid duly licensed Widows XP SP 3 installed on my PC. I have the product key but that you do not have the Windows XP CD with me. Now when I try to install "Language support additional" icon "Option Regional & language ' in the Control Panel, he asks the Windows XP CD (which I did not). Can anyone tell how I can install Supllemental Language support without the Windows XP CD?

    Hello

    · What is the number and the model of the computer?

    · Who is the service pack installed?

    You can follow the steps listed below, when it prompts for the windows XP CD:

    Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

    For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: How do I back up and restore the registry in Windows: http://support.microsoft.com/kb/322756

    a. click Start, click run, type regedit in the Open box and then click OK.

    b. find the following registry key:

    HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Setup

    (c) in the component, right-click ServicePackSourcePath, click modify, type %windir%\ServicePackFilesand then click OK.

    If the steps above does not help then you may need to contact the manufacturer of the computer for the Setup disk.

  • How can I reinstall the original operating system was on my Fujitsu Lifebook without the CD?

    I have a Fujitsu Lifebook series S, model S7211, and I had a bug on the computer, so I had to reinstall the OS, but my computer never came with a disc as it was a gift, so I had to install another OS that was intended for another computer, a DELL computer. I noticed right away that some of the functions that the computer was previously working is no longer, and it doesn't bother me at first, but now my computer seems to run slower, and I wanted to find a way to reinstall the original OS. I have the product key, but I can't find a way to download Windows Vista business on the Windows website.

    Can someone direct me to a download link or the part of the windows Web site I where can I enter my product key and to create a disk so I can install it?

    Hello

    You cannot use a Dell disk on a Fujitsu laptop.

    There are several ways to reinstall Vista, see what you can use..

    There is no Windows Vista downloads available from Microsoft.

    You can contact your computer manufacturer and ask them to send you a set of recovery disks.

    They should do this for a small fee.

    To reinstall Vista using their recovery disk/s, you start from the 1st recovery disk they provide and follow the manufacturer's instructions to reinstall:

    You need to change the Boot order to make the DVD/CD drive 1st in the boot order:

    How to change the Boot order in BIOS:

    http://pcsupport.about.com/od/fixtheproblem/SS/bootorderchange.htm

    "How to replace Microsoft software or hardware, order service packs and replace product manuals.

    http://support.Microsoft.com/kb/326246

    And if you have never received a recovery disk when you bought your computer, there may always be a recovery Partition on the hard drive to reinstall Vista on how you purchased your computer.

    The recovery process can be started by pressing a particular combination of the key or keys at startup. (Power on / start)

    Maybe it's F10, F11, Alt + F10, etc., depending on the manufacturer.

    Ask them to the proper key sequence.

    Some manufacturers have more available Vista recovery disks.

    If this happens, you may need to try this instead:

    You can also borrow and use a Microsoft Vista DVD, which contains the files for the different editions of Vista (Home Basic, Home Premium, Business and Ultimate) must be installed. The product key on your computer / Laptop box determines what Edition is installed.

    Other manufacturers recovery DVDs are should not be used for this purpose.

    And you need to know the version of 'bit' for Vista, as 32-bit and 64-bit editions come on different DVDs

    Here's how to do a clean install of Vista using a DVD of Vista from Microsoft:

    "How to do a clean install and configure with a full Version of Vista '

    http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html

    And once the operating system is installed, go to your computer manufacturer's website and get the latest drivers for your particular model or laptop computer.

    And phone Activation may be necessary when you use the above installation method.

    "How to activate Vista normally and by Activation of the phone '

    http://www.Vistax64.com/tutorials/84488-activate-Vista-phone.html

    See you soon.

  • Cannot connect to internet after Windows update. With the help of windows 7 on a brand new computer

    Just got a new laptop last week... The internet worked right out of the box... Now last night I let windows do a big update, and now my internet does not work...  It says something about "connects to the DNS servers.

    So I did a system restore to an earlier time, and the internet works fine...

    which ____ should I do?

    Hi 31aboy,
     
    Welcome to the Microsoft Answers community.
     
    Try to install the update to windows in clean boot mode.

    To enter the mode of clean boot on your computer, follow these steps.
    1. click on start, type msconfig in the search box and press ENTER.
     
    If you are prompted for an administrator password or a confirmation, type the password, or click on continue.
     
    2. in the general tab, click Selective startup.
    3. under Selective startup, clear the check box load startup items.
    4. click on the Services tab, select the hide all Microsoft Services check box, and then click Disable all.
    5. click on OK.
    6. When you are prompted, click on restart.
    7. now run windows update.

    http://support.microsoft.com/kb/331796 . In addition, see the section on how to restore your computer to a Normal startup mode.
     
    If you are facing the same problem even after installing the update in clean boot mode, then check the update in windows update history and send me the update name.
     
    Steps to view the windows update history:
     
    1. open Windows Update by clicking the Start button, all programs and then click Windows Update.
    2. in the left pane, click view update history.
     
    Hope this information is useful.
    Let me know if it worked.
     
    Thank you, and in what concerns:
    Umesh P - Microsoft Support
    Visit our http://social.answers.microsoft.com/Forums/en-US/answersfeedback/threads/ Microsoft answers feedback Forum and let us know what you think.

  • Trace channels by name without the help of a script.

    Hello

    I'm looking to draw channels, by using a report model, without having to rely on the index of each channel. I am processing the data from different sources and although they have the same marking convention for certain types of channels, some sources generate unique channels that can shake the index, and I have to manually put the parcels on the right channels.

    Is there a way around this without the use of scripts?

    Thanks for any help.

    Kevin

    I think that you can configure your report models as they reference channels by name, as opposed to the number.

    I have not used but check it out

    
    

    Or try this

    On the report tab, go to settings > Layout Set Up > layout settings and I believe that you change the channel reference it as well

  • need window 8 but to the help of the Government and cannot be paid forest

    somebory install me fake window 7, now I need window 8 but I govermet help and I can't pay no lisence I ask

    Microsoft if it can install it for free for me thank you eliexer

    ERH

    There is no install free sorry.

  • RAID 5 volume is corrupted, RAW and not NTFS file systems shows now Windows can't read the Volume.

    RAID 5 volume is corrupted, files systems shows RAW and not NTFS now, Windows cannot read Volume, how do I convert to NTFS without losing data on the Volume. Raid 5 has been created by the Raid software

    Hello

    Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Technet Forum. You can follow the link to your question:

    http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

    Hope this information helps.

  • II you need VERY basic instructions on how to stop a program from running at startup, without the help of Windows Defender.

    I have a Vista operating system, I use Firefox as my browser and I have MS Security Essentials, I turn off my Windows Defender.  I want to disable some programs from starting automatically, but I can't figure out how do it when I can not use this feature in Windows Defender.  I'm not at all read and write or experienced in computers or software, so PLEASE keep this in mind.  I really need advice for flush on a kindergarten, with each specific step the easiest way, so I can understand & follow him.

    Thank you for your help in this matter, as well as for your understanding of my limitations.

    CA DJ

    Hello

    Without knowing the programs you want to disable, I'll start by saying that I can't be responsible for adverse effect to the normal operation of your system.

    That said...

    • Click Start
    • Type msconfig and press enter
    • Click on the Startup tab

    You will see checkboxes for programs that run at startup.

    Or you can use a more comprehensive tool called autoruns...

    http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx

    Maybe is a better way to explore the settings for the programs themselves, there is often a check box for "do not run at startup.

    Tricky

  • Try to do a repair of Windows 7 installation, receive the message error "the following problems prevent upgrade Windows"

    Hi, I got problem with IE 9 RC.  I posted here, but there is no solution! (I can't send mail to Hotmail).

    I tried the final version of IE9, but the problem didn't slove. I tried to fix the Win7 + sp1 (upgarde) but it shows me this message:
    The following problems prevent upgrade Windows. Cancel the upgrade, perform each task and then restart the upgrade to continue.
    Your current version of Windows is more recent than the version that you are trying to level to. Windows is unable to complete the upgrade.
    Windows needs to be restarted if necessary to system files can be changed before you continue.
    The upgrade of Windows will affect the following programs or devices:
    These devices may not work properly after the upgrade. Before the upgrade, we recommend that you update the drivers for those devices. Cancel the upgrade, open the control panel and search for "update device drivers" or go to the website of the manufacturer of the device to search for updated drivers.
    USB Virtualization: Stub virtualization USB driver
    These programs may not work properly after the upgrade. We recommend that you uninstall these programs before upgrading. Cancel the upgrade, open Control Panel and search for "uninstall a program". (Note: programs marked as * can be reinstalled securely after the upgrade.)
    Age of Empires III
     
    and thank you.

    I tried wake SP1 with windows installation, but it did not work, I installed clean.

    Thanks to you all.

  • The closure of many application windows unexpectedly quit without the application itself.

    Whenever I asked several windows open on my iMac, one or all windows frequently and unexpectedly close. Does not close the application itself, but the screens disappear.  I can reopen it the windows in the dock or by command-tab.  It is not a question of active corners, shortcuts, etc.  The windows, that I don't use sporadically close while I am engaged in another window.  VERY interruption.  Any ideas?

    As the elements are always there when you command-tab, it looks like you accidentally select "Hide others" (option-command-H).

Maybe you are looking for