T40 USB question "this device can perform faster.

Similar Questions

• Message: This device can perform faster if you connect high speed USB

  Hello

  I have a laptop Toshiba Satellite 2009 of Vista.
  I just bought a multimedia design Memup Feel of the disc hard 500 GB.

  My concern is that when I connect to my PC, I have the following message:
  + This device can perform faster. USB devices can be faster if you connect to a USB 2.0 high speed +.
  + To get the list of available ports, click here. +

  Then I have a list of ports in bold, but I don't know what to do with.

  How to solve my problem?

  Thank you

  Hello

  Are you sure that your laptop is Satellite 2009?
  I put t know this model of laptop.

  But I know that this error message; This message appears if you connect a USB 2.0 device to a slower USB port; That is, USB 1.1
  But I think that your laptop supports USB 2.0 ports either TI problem disc external HARD s or the issue of USB drivers
  Try updating the chipset driver you can also delete all the USB controllers and hubs in Device Manager ports. Restart the unit. After restarting again the OS would recognize all USB ports.
  Then try to reconnect the USB HDD

• Receive the error message"this device can perform faster if you connect it to a 2.0 port" in the taskbar

  In the taskbar, this always happens "this USB device can perform faster if you connect it to a 2.0 port" and is a list of the USB Composite device. How can I prevent this arise?

  Hello

  1. Once you get this error message?

  2. it happens with all USB devices or is this a problem with a specific USB device?

  3. has the USB works well before camera?

  Method 1 : perform the following steps to stop this message from popping and check whether the problem is resolved or not.

  has. in the search box Type Device Manager start and click on enter.

  b. find now the option called Universal serial bus.

  c. now right-click on it and select search the hardware changes.

  Method 2 : run the troubleshooter of material and check if the problem is solved or not.

  Open the hardware and devices Troubleshooter

  Hope that helps.

• This device can perform faster ".

  the prompt: this device can run faster ' custody arise and no device is connected?  No usb port has a hip device?

  Again, nothing is plugged into a usb port.

  each comment that the system continues to show me tells me to unplug the unit.  There is no device.  what Miss me?

  Thank you

  Go into Device Manager, there may be something inside your computer, not only a USB / external peripheral. Look for something with an icon of warning or something. See if you can see what's wrong, give a screenshot or two, and we can work from there :)

• T110-107 "this device can run faster.

  Hi, when I move the lid I get the message "this device can perform faster" referring to USB 2.0. USB transfer rate is very slow after this message. Any ideas? Thank you

  Hello

  > "This device can perform faster" referring to USB 2.0. USB transfer rate is very slow after this message. Any ideas?

  You must update the chipset drivers and this error will disappear :)

• How can I get the drivers for xp usb / get the device can run faster in the listed ports

  POP UP WITH SAYING HIS DEVICE CAN RUN FASTER IN THE PORTS LISTED, I HAVE THE WIRELESS CARD WIRELESS, MOUSE AND SPRINT U600, CONNECTED TO THE LAPTOP, THE PROBLEM JUST STARTED

  See the discussion of the difference between USB 1.1 and USB 2.0 and why this error message http://ask-leo.com/what_does_the_usb_device_can_perform_faster_mean.html
  If you have an old computer, you do not all USB 2.0 ports or some of your USB ports may be 1.1 e.a. 2.0

  Open the Device Manager (start > run > devmgmt.msc > OK) and expand the "Controllers of Bus USB" section by clicking on the + sign to the left.

  Are there warning icons? If so, provide details

  It will probably take several entries for "PCI to USB Host Controller" or similar terms.  Please report if one (or several) of these entries are for a "PCI to USB Enhanced Host Controller.  If none of the USB controllers is "strengthened", you do not have USB 2.0

• USB device can run faster

  Hi all

  I recently bought a USB-6008.  When I plug it into my PC, I get a message "this device can perform faster.  This USB device can perform faster if you connect it to a Hi-Speed USB 2.0 port.  For a list of available ports, click here. "When I click on the message, it shows me a list of available ports, but none of them seem not to be USB 2.0.

  All my USB ports are supposed to be USB 2.0.  It is an Asus P5N72 - T Premium mobo.  I have updated the bios, and made sure that USB 2.0 is selected in the bios Setup.  I use Win XP SP3.  According to the Microsoft Web site, there was a known problem with XP supporting USB 2.0 on Asus Motherboards, but that he was supposed to have been fixed in SP1.

  I realize that it is a matter of Windows probably more than a question of data acquisition, but I spent the entire afternoon on Microsoft, Asus and other sites.  Can anyone help?

  Thank you

  Ed

  
  

• Satellite Pro A60 PL: message: USB device can run faster

  Hello!

  I have a problem with the USB 2.0 drivers in my Satellite Pro A60 PL. everytime when I connect the message apear theres USB 2.0 device this device can run faster. What can I do about it?

  Hi guys

  I received the same message. It s not an error but a balloon tip Windows.
  I didn't find the reason for this message because my phone supports USB 2.0 ports too and I also connected a USB 2.0 compatible device.

  I've tired to remove the Device Manager, the controllers and the USB hubs and updated the Win XP operating system to the last State. I've also updated the driver chipset but sometimes (not always) this message again using a disc HARD 2.5 USB.

  I read in some professional computer magazines that this message is normal and it might appears with some SATA external USB hard drives. So you can ignore it.
  It s nothing serious.

  Greetings

• "This USB mass storage device can transfer information faster if you connect it to a USB 3.0 port Superspeed ' when the device is already connected to a USB 3.0 port.

  I just bought and installed a USB 3.0 card. It is the Startech PEXUSB3S2 PCIe card. I installed the card in a PCIe 2.0 X 1 slot. The manual says it's exactly the slot, that it supports.

  The Manager device displays NEC Electronics USB 3.0 Host Controller and NEC Electronics USB 3.0 Root Hub are installed and are working correctly. I have a Thermaltake BLACX5G 5 G USB 3.0 hard drive caddy. The transfer rate is only 35 MB/s using the HDTune benchmark. It is a USB 2.0 speed.

  When the player is turned on, windows displays the message "this USB mass storage device can transfer information faster if you connect it to a Super speed USB 3.0 port»

  For some reason, the system doesn't see the caddy to drive USB 3.0 as being plugged into a USB 3.0 port, when it actually is.

  I remember having this same problem with Windows XP, when I bought a USB 2.0 card. The only thing that fixed it at the time was upgraded to XP SP2.

  This should not be a problem because I know that Windows 7 pro 64-bit supports USB 3.0.

  My motherboard is an ASUS P5QL-EM support an Intel Core 2 Quad and 4 GB of DDR2 memory. According to the manual owner the PCIe x 1 slots support architecture 1.0 and 2.0.

  Edit: I just tested the external hard drive and expansion card USB 3.0 on my motherboard Gigabyte of friends running Windows XP. Everything worked perfectly, no problems at all.

  Here, there is a problem with Windows 7 or the motherboard. Still unresolved, currently installs a floppy drive so I can update the firmware of my motherboard.

  I checked the implementation of the card several times, removed and installed in another motherboard to test, then removed and reinstalled again in my motherboard ASUS check several times for a fit course.  It still does not work. I have just completed update the firmware of the motherboard with the latest version, and I also did a new install of Windows 7, install the drivers USB 3.0 immediately after installing Windows over. None of this solves the problem.

  I'm running out of ideas on how to fix this without doing something drastic as a replacement for my motherboard. I don't want the speed of USB 3.0, but I don't think I'm ready for an another two or three hundred dollars to get it.

  I've been all over the ' net trying to find a solution and read tons about USB USB 3.0 specifically and in general. I can find no reason why the drivers would install and report that they are working correctly, but fail to connect to 3.0 speeds. I think that this would generate a certain type of error instead of such a strange symptom.

  EDIT:

  Here go us. I knew that is was a bad idea to buy one main (ASUS P5QL-EM) card that had to be overclocked to 1066 MHz for DRAM memory. I did all this work, and every time I reset my BIOS or updated it would always be the frequency DRAM back to where it should be (1066). After a reset of the computer was the starter and I just let it start instead of setting the DRAM frequency and, suddenly, USB 3.0 card worked perfectly. I confirmed this by setting the frequency to 1066 and looking at the USB 3.0 card fail again. I guess it must have something to do with the clock being sent to the PCIe bus.

  In any case, the USB 3.0 card works perfectly and gives me a transfer rate HD Tune to 99 MB/s on a drive from WD SATA 7200 RPM and 86.1 Mbps on a Samsung drive hard 5400 RPM / MIN 3,5 "SATA. These are the same reference points I get when these drives are connected to my internal SATA connectors. I'd say USB 3.o works perfectly now and maxing out the hard drives performance.

  Thanks for any help.

• IBM Thinkpad message: 'this machine can run faster with the USB 2.0 hub.

  Original title: Thinkpad USB 2.0 Hub.

  Hello:

  I have an IBM Thinkpad T-21 which is under Ubuntu & Windows xp.  I primarily use Windows XP.  The pop-up that keeps occurring is "this machine can run faster with the USB 2.0 hub.  Can you tell me how to upgrade my USB 2.0 Hub?  Would like to know because I can't sync my Android phone with my computer until I do it. Thank you.

  Are you sure you copied this error message properly?  In other words, he says that the hub could perform better if connected to a USB 2.0 port?  As far as I can determine that the T21 is not come with a USB 2.0 port, even if you connect a USB 2.0 device (for example a hub), the unit will only race as fast as the port allows it.

  What is the brand and model of your terminal?

  It is possible that the message means the opposite (i.e., your computer has a USB 2.0 port, but the hub is only a USB 1.1 device).

  USB 2.0 was introduced in 2001, so if you bought your computer before 2001, it is likely that you use USB 1.1 or 1.0.

  Open the Device Manager (start > run > devmgmt.msc > OK)
  Expand the category of 'USB Bus controllers'.
  If you see the "Enhanced" work for one or more of the listed devices, you have a USB 2.0 port.  If you do not see "Enhanced", you have USB 1.1.

  

  If the problem is that the USB port on the computer is not 2.0, so your only solution is to buy a USB 2.0 PC Card adapter.  Example and example 2
  If the problem is that the hub is not 2.0, then you will need to buy a new hub.

• USB 3.0"your device can run faster.

  I recently bought a HP ENVY 15 t-j100 Quad CTO Notebook Windows 7 Professional Edition (PC product #: E1P05AV). Four ports are supposed to be usb 3.0, but sometimes when I put my flashdrive 3.0 in, it says "your device can run faster. I've updated all the drivers and the problem seemed to go away. But recently I have found that if I do not have the flash 3.0 player in the port completely, or if I do it slowly, he sometimes with the same message. Might not have in a sense caused the problem in the first place? It is even supposed to have this message when this happens? Any help would be appreciated.

  Hello cck979,

  I see that you have a problem with 3.0 ports on your laptop and your flash 3.0 player. I will try to help you with this.

  This document may have information and steps that will help you: Troubleshooting connections USB (Windows 7). Generally however if the unit is not plugged in all the way or it won't work not otherwise you will get some sort of message.

  Also have you noticed if this happens with all ports, or a specific port?

  See if the document offers further assistance.
  Thanks for posting on the HP Forums.

• Devices on all my iCloud preferences says "this device can be used to receive codes of audit ID Apple." How can I change this if at least one, if not several, can receive the verification code?

  Devices on all my iCloud preferences says "this device can be used to receive codes of audit ID Apple." How can I change this if at least one, if not several, can receive the verification code?

  Try to go here and see if you can add them to your Apple ID.

• USB port can perform faster pop-up

  I keep getting an annoying pop up that 'USB port can run faster. This must be an internal port that I get this when no external USB has anything plugged.

  Go to the website of the manufacturer of your computer/laptop > drivers and downloads Section > key in your model number > look for the latest Vista drivers > download/install them.

  See you soon.

  Mick Murphy - Microsoft partner

• 4 usb ports - this device is disabled because the firmware of the device did not give him the necessary resources. (Code 29)

  m facing a problem with hub 4 ports usb of my... When I connect usb hub my with my usb keyboard and mouse, and then the lights of the suite to get devices but they doesnot work... and the error message shows... I checked in Device Manager and I got the message details which are given below.

  Device status:

  This device is disabled because the firmware of the device did not give him the necessary resources. (Code 29)

  driver version:

  6.1.7601.17514

  Please help me... Thank you.

  Hello

  In the Device Manager - right click on the device and Uninstall - when complete reboot.

  Check in the Device Manager to see if the device re-installed. If it isn't action - Scan for
  hardware changes.

  Also check the BIOS - Setup/settings - often F2 for system start - make sure that the USB port
  is activated. Check with Support from the manufacturer of the system/motherboard, their documentation online.
  and ask in their forums.

  How to fix error Code 29
  http://pcsupport.about.com/od/errorc/a/code-29-error.htm

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Message says that this device may function more quickly.

  I just bought a usb hub 4 ports to run my printer, USB key and a receiver 2.4 ghz for my keyboard and mouse, since then I get this message this device can run faster , I opened, but I do not understand what its actually means!
  I am happy with the speed because it is at the moment so can I get rid of this pop like me crazy! in this case every 5 minutes or more, also atuoplay
  window for my cd/dvd drive also opens in the background at the same time. I'm relatively new to this game, so if you could help I would be much obliged
  If you could explain the answer Mr. thow I was a 10 yr old it would help :)

  MIK niwdog

  MIK niwdog,
  Thank you for visiting the Microsoft Answers community forum.

  What a message means that you have plugged a USB 2.0 on a USB 1.1 device.  Try connecting the device to a different USB port on your computer.  If the error keeps popping up, here's how to disable:

  Open Device Manager by clicking the Start button, click on the Control Panel, clicking system and Maintenance, and then clicking Device Manager.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  Expand the section indicating Bus USB controllers.
  Right-click on anything that has the word "controller" at the end, as a Standard Enhanced PCI controller USB host (or something similar), click Properties, click Advanced, and check in the box that says "don't tell me about USB errors".

  AutoPlay is popping up because he sees your USB and want to autoplay anything on it.

  How can I stop asking me what program I want to use?

  Disable AutoPlay for only one type of media
  1. open AutoPlay by clicking the Start button, clicking Control Panel, on material and audio and then click AutoPlay.
   
  2. in the list next to each type of media that you do not want to be asked questions on, select take no action and then click Save.

  Let us know if you need more information.
  Thank you

  Gloria
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.