T510 - wireless question - connects to the local network but no Internet access

Similar Questions

• HP OfficeJet Pro 8600: HP OfficeJet Pro 8600, connected to the local network but does not print a printer on the same LAN

  HP OfficeJet Pro 8600, connected to the local network but cannot print printer on the same local network.

  Work tried fixing it but all attempts fail.

  Firewall disabled.

  Printer recognizes the router's LAN.

  Was also pointed out that the port does not communicate, can not remove it; Cannot add another...

  Printer does not print.

  How can I fix?

  Hi @AnnisMonadjem,

  Welcome to the Forums of HP Support!

  I understand that you are unable to print to your printer HP Officejet Pro 8600. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  When you say 'LAN', are you referring to the network or you try to share the printer on the network?

  How is the printer connected? (Ethernet/WiFi)

  If you have noticed that the port is causing problems, please download and run the print and Scan doctor, it will be probably diagnose and fix the problem you are experiencing.

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  HP has several Officejet Pro 8600 series.

  What is the name and the product number of your printer? How can I find my model number or product number?

  • Update the firmware of the printer.
  • Don't hide the SSID (network name).
  • What type of encryption are you helping? HP recommends WPA and WPA2.
  • You have a double router broadband? Make sure that the two groups were not the same network name.

  If the problem persists, you may encounter an IP address conflict. It's a good idea to assign the printer a static IP address outside your DHCP range. For example, some routers default DHCP is located between 192.168.0.100 to 192.168.0.200. So, I would use 192.168.0.232.

  To assign the static IP address, use the following steps as a guide.

  • Print a Page of Network Configuration menu of the printer front panel. Note the IP printer. IPV4 address
  • Type the IP address in the browser to bring up the SAP.
  • Choose the network tab, then wireless on the left side, and then select the IPv4 tab.
  • Select Manual IP.
  • Enter your IP address manual (192.168.0.232)
  • Enter 255.255.255.0 for the subnet mask, except if it is different.
  • Enter the IP address of your router that sits on the Network Configuration Page) for the default gateway.
  • Please, click on manual DNS server. For the preferred DNS Server Manual please enter 8.8.8.8 and the Alternate DNS Server Manual, please enter 8.8.4.4.
  • Click on apply.
  • Restart the router, the printer and the computer.
  • Test printing and scanning.

  If the problem persists, download and run this patch rollup: resolving printing issues in Windows 7 and Windows Server 2008 R2

  • Try printing and scanning.

  In addition, if you are still having problems try the steps in this guide, HP printers - "offline" Status Message printer (Windows 7).

  Continue on, if the problem persists.

  Important!   Delete the temporary files and folders by using the disk cleanup utility

  1. Open the disk cleanup utility:

• I can connect to the local network, but not to the internet

  Why in an internet connection, I can connect to the Local network, but not to the Internet.
  I have valid IP address and configuration is good.

  I recommend you read some threads here in the forum about similar issues.
  If this problem occurs using the WiFi network, then check if you can use the connection to the local network.
  Using the WiFi network, you must check if the common WLan parameters are favourable;
  Check if the encryption key is right; turn off filtering by mac address, check the TCP/IP protocol settings if it has been set to automatic, disable the firewall settings, rest you WLan router, check if you connected to the right SSID.

  Good bye

• Connected to the local network, but can not use internet

  I recently had problems with access to the internet after reinstalling windows 7. Before the reinstall worked very well.

  I can connect to the local network without problem, and it shows that the internet is connected. Yet I can not access the internet. When I disconnect and reconnect, I get a few seconds of internet work before it stops working.

  When a diagnosis in the network and sharing Center, I get the error "default gateway is not available" and occasionally "the connection between your access point, etc. and internet is broken"

  Other computers and devices using the network are working properly, although there was a 'competitor IP address' error on another pc, which, after a reconnection, solved itself.

  I use an edimax 802.11n wireless card and a D-link router

  I tried several things to make it work again, but without result. Any help would be greatly appreciated

  disable TCP/IPv6 had no effect.

  I think I can have fixed me, I installed the driver microsoft before the reinstall instead of the driver edimax and internet suddenly started working.

  Thanks for the help of yor

• Why if a system is xp and one system is windows 7 and the two connected to the local network, but file-sharing does not work

  a system is xp, another system is windows 7 basic and both connected to the local network, after you set up shared drive, mowing arrives not

  Hi Abhay,

  I suggest disable you the password protected sharing and check if it helps.

  Networking of computers running different versions of Windows

  Note: Follow the steps in the section "to enable sharing protected by password in Windows 7" and turn off password protected sharing.

• I have a Vista Enterprise desktop connected to the local network, but the notification icon still shows disconnected state

  I have my Vista connected to the network and the "network and sharing Center" shows that it is connected and network is accessible, but the network in the status bar icon displays an icon showing disconnected state. How to solve this problem? Restart does not help

  Guru

  Check and make sure you have these services defined in this way. This initiative will establish whether there is a connection.

  1 - on the road - network Manual connections
  2 network list Service - auto-
  3 network Location Awareness - road - automatic
  4. bad Service Network Interface - on the road - automatic

• lost internet, tcp/ip is not binding to connect to the local network.

  cannot access internet on network adpt since Saturday, January 22, 10.  said Network Diagnostics does not bind ip to connect to the LAN adpt.  When I go to L A Conn ipv4and6 properties are both checked.  I uninstalled and reinstalled the ptba and ip lan protocols.  ipconfig/all shows no IP information.  I have reset the battery.  network of diag stills said make sure that tcp/ip4 and ip6/tcp are selected in the config to connect to the local network [but they].  TIA

  try to uninstall and reinstall the network drivers and check if that helps

  For more information, you can refer to:
  http://www.madboa.com/geek/SOHO-bind/
  http://TechNet.Microsoft.com/en-us/library/cc977313.aspx

• Impossible to connect to the wireless network when the wireless Internet is filled to connect to the Local network

  I tried to fill the connection between my laptop Wi - Fi and an ethernet cable LAN via the connection to the Local network for my xbox 360. However, when the connections passed the wireless connection would show that it is disconnected and would not reconnect. When I tried to repeat the process sometimes the same thing happens sometimes it says that it is still connected.

  However, be that as it may, both times I could not load any page of the website from my laptop and xbox connect any.
  How can I create a network bridge and get the wireless internet to connect please?

  Any help to fix this would be appreciated,
  P

  This Microsoft Knowledge Base article might help: bridge may not work with a Non-Promiscuous Mode network card .

  If not, I recommend to delete the network bridge and enable sharing of Internet connection on the wireless network connection. Boulder computer Maven
  Most Microsoft Valuable Professional

• No Internet access, the 'Connect to the Local network' and 'Wireless network connection' are "Local only".

  I'm portable computer maintenance of the customer, a Toshiba Satellite L305-S5885, under Vista Home Premium x 86 SP2, with infections by malicious software and internet connection problems. I have managed to get rid of all of its 251 infections and I am now addressing the connectivity problem. I'm unable to achieve on its ethernet or a wireless connection to Internet. The two network status of connections 'Unidentified network', and also ' access: Local only ' all other machines hooked up to my router via CAT5e and some via 802.11 g/n, have excellent speeds with internet connectivity, so I know that the problem is limited to his machine. I tried the following:

  Deactivation and reactivation of these two connections: FAIL.

  "Diagnose and repair" on the two connections: FAIL.

  Under dynamic I.P. type to static/static to the dynamic: FAIL.

  Uninstalled all network via Device Manager devices, then restart: FAIL.

  Manually uninstalled all the drivers and utility and installed the latest versions: FAIL

  The command ipconfig/all text follows:

  ----------------------------------------------
  Microsoft Windows [Version 6.0.6002]
  Copyright (c) 2006 Microsoft Corporation. All rights reserved.

  C:\Users\Brooklyn's>ipconfig/all

  Windows IP configuration

  Name of the host...: Brooklyns-PC
  Primary Dns suffix...:
  Node... type: broadcast
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Intel (r) Wireless WiFi Link 4965AGN
  Physical address.... : 00-21-5C-31-87-95
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Autoconfiguration IPv4 address. . : 169.254.174.235 (Preferred)
  ... Subnet mask: 255.255.0.0.
  ... Default gateway. :
  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :
  Description...: Realtek RTL8102E Family PCI - E Fast Ethern
  and NIC (NDIS 6.0)
  Physical address.... : 00-1E-33-4E-2E-F7
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Autoconfiguration IPv4 address. . : 169.254.74.29 (Preferred)
  ... Subnet mask: 255.255.0.0.
  ... Default gateway. :
  NetBIOS over TCP/IP...: enabled

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {C41651CC-0B3D-411D-8187-745214 C 69}
  B4B}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 11:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {816357D 3-D 8-494C-AA09-F622AE861 44}
  0FA}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 14:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 02-00-54-55-4E-01
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  C:\Users\Brooklyn's >
  --------------------------------------------------

  Guys, I'm really hitting my head against the wall on this one, and I would be VERY happy for any help through this. Thank you!

  I thought about it, there was a corrupted installation of Norton 360, the origin of the problem. I've used the Norton removal tool and voila! Internet! Thank you.

• Re: Satellite Pro A40 - connection to the local network

  Hello

  My names Andy and not bieng a total beginner computer, I tried to install all the drivers for my laptop model a SPA40 old fathers PSA45E-001VM-EN. (European model I think) everything looks ok, except that I can't get the ETHERNET driver.

  When I go into the Device Manager there is NO controller network displayed in the list and there is a yellow exclamation mark against two controllers ethernet ib the OTHER DEVICES tab looking here, I downloaded the atheros wlan xp file - 7704062.zip, broadcom wlan xp - installed 5604835.ziplan20070912134727.zip and nothing changes, we used to be able to go on the net and with the wifi card in the pci slot wireless go so I know its capable I think it's just the order of drivers and the drivers themselves,

  Then someone can point me in the right direction before as I have send myself crazy with this...

  You can

  regards and thanks in advance

  Andy

  Hey,.

  The drivers that you downloaded are WLAN Card and has nothing to do with the connection to the local network (Ethernet) normal

  I think you should check the Web from Toshiba site to download the latest LAN driver. You can find the drivers for Satellite Pro A40 in * archives *.
  ttp://EU.computers.Toshiba-Europe.com/innovation/download_drivers_bios.jsp h

• Satellite A105-4114 will not recognize the connection to the local network

  Whenever I plug my cable ethernet to ethernet port on my laptop, the ethernet port does not recognize my cable, even if the lights are flashing. I updated my LAN driver a week ago, and it has not really helped. My internet service is provided by my apartment complex at the school, but I don't think it has anything to do with it, because I had this problem last year living in dorms and at home. I have to restart my computer everytime for my computer to recognize the connection to the local network. Can someone help me please?

  Driver: Intel (r) PRO/1000 PL Network Connection

  Wireless connection works fune.

  Hello

  First of all, you should check your LAN cable.
  Sometimes the laptop may not be correctly connected to the LAN as a result of a defective cable.
  In addition, you should check if the network card is properly recognized in Device Manager. He should t be a yellow exclamation!
  In addition, you must check the settings for the TCP/IP protocol in the LAN card properties.
  TCP/IP must be set to automatic. I assume that you are connected to a server and the server supports supported a range of IP addresses and assigns it automatically.

  Last but not least check if you are using the latest version of the BIOS.

  Welcome them

• No connection to the local network, cannot connect - Satellite M35-S163

  I think I've tried about 10 different drivers, but I can't ALWAYS connect to the local network.

  He will not get an IP address.

  Other computers have no problem and are connected through the router, but it just won't connect.

  DHCP in router, IP config says the get IP address... No firewall issue... Any new installation of XP SP2

  Any ideas?

  OH, and regarding this... discovered Ethernet controller driver is on one of the Wireless drivers... z

  Hello

  I m bit confused.
  The LAN card is recognized correctly in the Device Manager?
  Check under network adapters and if there is NO yellow exclamation point.

  If the network card is recognized correctly, then you should check the LAN parameters-> * Protocol of TCP/IP.

  IP address, getway must be set to assign automatically.

  Check it!

• Connection to the local network not appearing is not in network connections

  A month or so I reinstalled Windows XP SP2 (have since updated to SP3), and ever since then the LAN connection icon does not appear in the network connections window, and even when I plug the ethernet cable it does not automatically turn on the connection to the local network. My wireless connection works perfectly well. I went to the HP website to download all the drivers and also visited if the Device Manager on my computer to make sure that all drivers are in place. Even with all the drivers, it still does not connect to the local network. Help, please!

  Hi rawkous,
   
  Follow the steps listed in this article to resolve the problem:
  How to troubleshoot missing network connections icons in Windows Server 2003 and Windows XP

• Network Diagnostics says "connection to the local network 2 has no valid ip address.

  Dear Sir/Madam,

  I use the computer dell laptop windows 7 Home premium 64-bit. Usually, I connect my laptop to the internet through wifi modem. It connects automatically to him and there is no problem. But suddenly, the connection is not showing this wifi but signal showing other signals. I plugged the cable, but not showing also no internet access, then I used the diagnosis then he showed "connection to the local network 2 has no valid ip address" other devices such as my phone, etc. are connect to this wifi normally.
  As there is no internet connection on my laptop, I downloaded "microsoft fix it" and installed in my laptop to another computer but it does not work, he showed me 3 tabs IE to read, etc. to fix it it is opening chrome Web site as there is no internet facility, displays "cannot display page" Web page
  so, please help me with this problem. feel free to ask all the necessary questions.
  Thank you
  Vandenplas, infant.

  Hi Vandenplas,

  Method 1

  Follow the advice given by Meghmala Feb 17,2010 on the thread: http://answers.microsoft.com/en-us/windows/forum/windows_7-networking/local-area-connection-does-not-have-valid-ip/72c61d55-4d20-48bd-80bf-cb25f7b95cb6

  Method 2

  Check the steps on the thread: http://windows.microsoft.com/en-IN/windows/network-connection-problem-help#network-problems=windows-7&v1h=win81tab1&v2h=win7tab1&v3h=winvistatab1&v4h=winxptab1

  Also check the discussion on the thread:'t-have-a/43ea076e-5210-4194-80d8-cb4681e852a0 http://answers.microsoft.com/en-us/windows/forum/windows_7-networking/issues-found-local-area-connection-doesn

  If nothing helps, you can try to contact your ISP and ask them to reset the settings.

  Hope this solves the problem. If the problem persists, you can write back to us and we will be happy to help you further.

  Thank you!

• (Connection to the local network) is not a valid IP configuration when you try to share internet via ethernet

  I shared my wireless network connection to my laptop with my Tower and I tried to change some things static ip and now my turn gets no internet at all. Here is my ip config for my laptop

  Windows IP configuration

  Name of the host...: Piro-PC

  Primary Dns suffix...:

  Type of node...: peer-to-peer

  Active... IP routing: No.

  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :

  ... Description: Atheros AR5008X Wireless Network adapt

  Physical address.... : 00-1F-3A-8E-D9-DC

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::a11b:747:8de1:c32a % 11 (Preferred)

  IPv4 address: 192.168.1.113 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Saturday, November 10, 2012 18:52:10

  End of the lease...: Sunday, November 11, 2012 19:14:35

  ... Default gateway. : 192.168.1.1.

  DHCP server...: 192.168.1.1.

  DHCPv6 IOOKING...: 218111802

  DHCPv6 DUID customer...: 00-01-00-01-13-C9-24-20-00-17-42-BC-C1-D3

  DNS servers...: 75.75.75.75

  75.75.76.76

  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :

  ... Description: Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller

  Physical address.... : 00-17-42-BC-C1-D3

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::283a:df5d:cf7a:d0ae % 10 (Preferred)

  Autoconfiguration IPv4 address. . : 169.254.208.174 (Preferred)

  ... Subnet mask: 255.255.0.0.

  ... Default gateway. :

  DHCPv6 IOOKING...: 234886978

  DHCPv6 DUID customer...: 00-01-00-01-13-C9-24-20-00-17-42-BC-C1-D3

  DNS servers: fec0:0:0:ffff:1 1%

  FEC0:0:0:FFFF:2 1%

  FEC0:0:0:FFFF:3 1%

  NetBIOS over TCP/IP...: enabled

  Tunnel adapter isatap. {B2EC9B12-C460-46DE-A9CC-9B8551AF0AF3}:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Microsoft ISATAP adapter

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {E818BF11-C224-432F-B7C0-3F2949FAADF8}:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Adapter Microsoft ISATAP #3

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 16:

  The connection-specific DNS suffix. :

  Description...
  . : Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  IPv6 address: 2001:0:9d38:953c:1893:f6:e7eb:e988 (Preferred)
  Address IPv6 local link...: fe80::1893:f6:e7eb:e988% 23 (Preferred)
  ... Default gateway. : ::
  NetBIOS over TCP/IP...: disabled

  Ethernet has no default gateway so he does not know where to look for information.  Its IP address indicates he can't get an IP address to the router, or the external DHCP/DNS servers.

  Go to network & share > change adapter settings > Ethernet > properties >... Enter the IP Address of the gateway by default even in wifi.