T60 - problems with long active standby
Hi all
Hopfully, can someone point me in the right direction with a problem I encounter with one of the ThinkPad T60.
Here's the run down:
We did 3 of the T60 (type 6369-A56) last December (online sales of web). 1 of the three displays problems when dealing with the day before. If the laptop goes into sleep mode during more than anywhere between 30 minutes to 1 hour that the laptop is not repeated mode standby when you open the lid of the laptop or use the Fn function key. When two approaches to bring the laptop leaves standby mode the Moon cresent LED stays on, the HARD Drive LED turns on for a brief second and then turns off, the power light and strong say, the screen remains blank at any time. When this happens, you can hear/feel the disk HARD turns to the top and doing something and you can also hear the CPU fan spin in the action as if it came out the day before. Does not seem to have taken power to make a difference with this problem.
I already talked to Lenovo support RELATIVE to this subject and they believe it's a software problem. I did a few more tests to try to determine that this is what I did...
I took a Norton Ghost image of one of the 2 working T60 HDD (Eve works perfectly on two other laptops) and used this Image for ghost in the T60 defective HARD drive, this gave me two identical laptops (hardware and software). Power for laptop mode is as follows, turn off the display @ 5 minutes, switch Mode suspend @ 15 minutes. I left computers laptops only at exactly 09:05, 5 minutes later so empty screens, @ 15 minutes later, the two went in standby mode. 45 min after sleep mode had struck I returned to two laptop computers and for laptops (at the same time), use the Fn key and the defective T60 does not return from the day before and the same symptoms as mentioned earlier it happened.
After this I decied to see what would happen if I changed the HARD drive between laptops (from the laptop failed drive in the laptop to work), failed hard drive of the laptop working in laptop. After the passage of the HARD drive, I ran the same tests as above. Yet once, 45 minutes after the day before had been very active, I used the Fn key to get out of sleep mode and the laptop with the failed hard drive from the laptop worked directly at the exit of the batt, but the hard drive of the laptop from work to the faulty laptop displayed the same problems as mentioned above thus excluding the software as the cause of the problem.
My question is, knowing all this, where is the problem likely to be? Is - it's going to be RAM related or associated with Board?
The result of likley going to be back to Lenovo for repair?
See you soon
Chris
Hello
Yes, after trying one number of other things I determinined it was the motherboard at fault. Introduced a job guaranteed with Lenovo and returned to the unit for repair. Less a week we had it back, running without problem (they replaced the sys Board).
See you soon
Chris
Tags: ThinkPad Notebooks
Similar Questions
-
Original title: Net User ID & Net password
After the upgrade from Vista to W7-64 CV, I have a problem with an active WiFi Seagate GoFlex TV Media Player asking for a "Net User ID & Net password" to log. I used all imaginable combinations of IDs & passwords, but they all lead to logon fails. I'm almost certain that it is a W7 security problem because others with the same players who went to W7 face the same problem. I found many supposed fixes online, but none works.
I am aware that MS W7 works as it should and Seagate is not their problem, but if anyone can recommend a change of security to help this issue, I guarantee a pass towards the sky.
PS: All the sharing, etc. continuously. are installed as they should be.
The only reference to Net User ID and password I can find is on page 46/47 of the User Guide. If this is not the user name and password of the Windows account that you want to share files with, I don't know what it is.
I guess patches that you tried to include those that are mentioned here:
I would have suggested the registry change.
It might be worth checking that you have the latest firmware, just in case.
http://knowledge.Seagate.com/articles/en_US/FAQ/216931en?language=en_US
-
I have a problem with the Activation of the key window expiring.
Original title: recovery partition
Hello
My Windows 7 ultimate activation code has expired, I was wandering if, in case I do a restore system from the recovery partition on my PC I could get it to work again for another year. Thank you.
Hi Casperthe,
If you had a real computer of Windows 7, or a valid Windows 7 product key, try these steps and check if it helps. A recent hardware change can cause this problem. I suggest you activate Windows 7 manually (activate by phone) and check if it helps.
a. click Startand in the search for box type: slui.exe 4
b. press the 'ENTER' key
c. Select your 'country ' in the list.
d. Select the "Phone Activation" option.
e. stay on the phone and wait for a person to help you with the activation.Check out the link for more information:
How to activate Windows 7 by phone
http://support.Microsoft.com/default.aspx/KB/950929/en=us
Hope this information helps. Answer the post with an up-to-date issue report to help you further.
-
Problem with Windows activation.
My PC with windows 8.0 PRO is installed has been works well, but all of a sudden, I get a screen come in saying - activate windows and offering a link to access the settings of PC - when I get to the screen, it says cannot activate Windows now, please try later.
Is it a virus or what?
PC seems to work ok.
Graham LB
[Original title: activate Windows]
1. press the Windows key + X , and then clickrun, and then type: slui.exe 4
2. then press the ENTER"" key.
3. Select your "country" in the list.
4. choose the option "activate phone".
5. stay on the phone (do not select/press all options) and wait for a person to help you with the activation.
6. explain your problem clearly to the support person.
-
Problem with the mode standby in Windows 7
Hello friends,
I have a big problem when Windows 7 updated itself. I have a laptop Toshiba Satellite L505D. When I close the lid, it will automatically 'sleep' mode. Unfortunately, the screen is black and the laptop is still in progress, I have to stop it and then turn. Is it a problem with the driver 'stack '? Please, help me :)
>.. After Windows 7 update itself
How to understand this?
Have you installed the Windows updates or what?Have you tried to restore the OS using System Restore tool and check if the problem persists?
-
Pavilion 15 laptop: problems with stop and "standby" mode.
I upgraded from windows 8.1 for windows 64 bit home 10. I had problems with stop and goes into sleep mode and cannot be resolved, then I reinstalled windows 10. Everything worked fine for a few moments, and then the same problem reappeared. I can't stop or put my PC into sleep mode, unless I have first of all to make a restart. After a reboot, I am able to stop or go to sleep mode without problem. If I try to do either without a restart, the screen goes black and the indicator light remains lit. The only way I can get it to start then press on and hold the power button and force a shutdown down, then press the power button to restart the upward. I have another PC, a wafer think that Lenovox has been upgraded to windows Windows 7 10. This PC work fine with windows 10, no problem at all. It's just the HP Pavilion 15 who has these questions. It makes me crazy.
Look through the tool of troubleshooting possible solutions here:
-
Problem with the activation of the Muse
I have a valid license for Creative cloud (until October 2016). After Muse update tell me, that I have the trial version of 7 days. Before the update, everything was in order. Please help with the activation of Muse (AE give me the same information )
Please refer to:
Stop Creative Cloud 2015 to return to the mode of trial
You run applications after the update is complete?
I believe that, after an update for Creative Cloud Application Manager, you must open at least one of the apps and let it re - link to its registration information, that has been my experience at least opening one of the applications, it behaves as if it is opened for the first time after such update.
Concerning
Stéphane
-
Problem with the activation of the scrolling features
Hi all:
I write a game application that takes advantage of two menus api normal (for the initial screen), as well as related graphical rendering tips, once the game is in progress. One of the menus I have is a statistics screen, implemented as follows:
class StatisticsScreen extends MainScreen { public StatisticsScreen(SpyderMainApplication p, long style) { super(style); parent = p; prof = parent.getProfile(); VerticalFieldManager vfm = new VerticalFieldManager( Manager.VERTICAL_SCROLLBAR | Manager.VERTICAL_SCROLL); LabelField title = new LabelField("Statistics", LabelField.FIELD_HCENTER); setTitle(title); // add total statistics LabelField totalTitle = new LabelField("Overall Statistics", LabelField.FIELD_LEFT); vfm.add(totalTitle); SeparatorField sft = new SeparatorField(); vfm.add(sft); vfm.add(new BasicManager(20)); ... adds a number of other fields inside of vfm, so that it *should* enable scrolling (the whole screen isn't visible) ... add(vfm); updateLayout(); } protected void sublayout(int width, int height) { super.sublayout(width, height); } }
The base Manager is implemented as follows:
import net.rim.device.api.ui.*; import net.rim.device.api.ui.component.*; import net.rim.device.api.system.*; //import net.rim.device.api.ui.container.*; class BasicManager extends Manager { int _managerHeight; // Total height of the manager // Pass in desired height. Scrolling is turned off in both directions. public BasicManager(int passHeight) { super(Manager.NO_HORIZONTAL_SCROLL | Manager.VERTICAL_SCROLL); _managerHeight = passHeight; } protected void sublayout(int width, int height) { BasicTextField field; // Loop through all the fields contained with the layout manager for (int lcv = 0; lcv < getFieldCount(); lcv++) { //Get the field. field = (BasicTextField)getField(lcv); //Obtain the custom x and y coordinates for //the field and set the position for //the field. switch (field.getCustomStyle()) { // Custom style 1 is for the left side of the text to be at 1/8th the width // of the screen case 1: setPositionChild(field, width / 8 , field.getY()); break; // Custom style 2 is for the right side of the text to be at 7/8ths the width // of the screen case 2: setPositionChild(field, width * 7 / 8 - field.getPreferredWidth(), field.getY()); break; // Any other custom style gets position strictly from X,Y default: setPositionChild(field, field.getX(), field.getY()); } //Layout the field. layoutChild(field, width, height); } //Set the manager's dimensions setExtent(width, _managerHeight); } } class BasicTextField extends LabelField { int _xPos, _yPos, _customStyle; // coordinates and style // We pass in the coordinates and the custom style BasicTextField(String passLabel, int passStyle, int passX, int passY) { super(passLabel); _xPos = passX; _yPos = passY; _customStyle = passStyle; } // Getters for position and style int getX() { return _xPos; } int getY() { return _yPos; } int getCustomStyle() { return _customStyle; } public int getPreferredWidth() { return Display.getWidth(); } public int getPreferredHeight() { return Display.getHeight(); } }
Now, the problem I have is that on any platform (curve 8330, pearl 8130, etc...), he will not allow the user to scroll to the bottom of the page. I did something wrong in my application? I can't get to allow scrolling...
Thanks in advance for any help!
~ Scott
A quick response - it's late for me. Default LabelField is not active, so the BB has no place where to focus on when you try to scroll down. The fastest solution is to be the subject of the LabelField FOCUS. Otherwise, announces a few NullFields that are focusable. Let us know if you need more.
-
vRA 7 load balancing with embedded active / standby vRO
I have a vRA environment 7 with vRA HA devices that have integrated the vRO. I want vRO to an Active/Passive configuration, but when I do the load balancer declares the node with the vRO vRA Eve out of service.
It seems that between 6.2 and 7 that VMware has changed the vRA health check to watch/vcac/service/api/health instead of/vcac/services/api/status. This new target now fail because it shows a service as in offline mode. While it is fairly clean and is probably better than the old health check, it kills the idea of an active configuration / standby vRO.
Any ideas on how I can get around this? Thank you!!
The problem that you are facing is that devices of internal load balancing is managed by HAProxy. I don't have * think * that it promotes health checks, this is why active/active approach for vRO. I suspect that if you want to use Active/passive, you will need to switch to external devices.
Grant
-
Problems with the activation of Windows XP 2002
Help!
Is there someone out there who can help me solve this problem?
I have a PC with Windows XP Professional 2002, Service Pack 2, control my LC - MS instrument that uses the MS Xcalibur software. Four weeks ago, I had a PC crash and re installed Windows XP by using the CD of Installation Re. On Thursday last week, he came a message that Windows must be enabled. I tried by phone, but my install ID has not been accepted. This PC came with Win XP is already installed. I find it very strange that it should be a problem to activate it once more!
Can someone please help me solve this problem?
It is very important to me, because the PC is to control the instrument SM - which is the work horse in my business.
Best regards
Gunnar Hagelin
Aquila Pharma Services AS
Norway
Moved to other/unknown install, upgrade and activate Forum.
Hi Gunnar,
Apologize for the delay in response. You can get the XP operating system correctly using the Activation of phone as described in the following article:
How to activate a Microsoft product using Microsoft Product Activation Center
Back to us for assistance.
-
Problems with the Activation of Windows 7 Professional
Hello, for a long time, my windows was genuine, but then I ran SpyHunter 4 to end a virus in my computer. But then I had to reset the computer, and then, the windows became a pirate and showing 7601 compilation and I started getting messages that I might be victim of falsification of software. Then, I clicked on the link to activate the window again. And then, I downloaded the WindowsActivationUpdate.exe, and when it ended, I have zero crashed my computer and I received this message, but the windows was always not authentic. Then I went to microsoft.com/genuine and tried to launch the legitcheck.hta, it starts and says that the validation of the window is current and recommended that I do not have to navigate beyond this page. But then, after awhile, it gets with and shows the following script errors:
Line 14
Character 41318
Line 11
Character 102675
Line 1
Character 15126
Line 6
Character 31
Line 0
Character 0
Line 2
Character 1
And then it becomes white forever. I tried to run the MGADiag.exe and here is my diagnosis:
Diagnostic report (1.9.0027.0):
-----------------------------------------
Validation of Windows data-->Validation code: 50
Validation caching Code online: n/a, hr = 0xc004f012
Windows product key: *-* - CM74G - RPHKF-PW487
Windows product key hash: 71BRYMECVaSXedfumfu8zryHJVY =
Windows product ID: 00371-177-0000061-85051
Windows product ID type: 5
Windows license type: retail
The Windows OS version: 6.1.7601.2.00010100.1.0.048
ID: {163752C2-0AB7-4A81-9190-57AC32A7D366} (1)
Admin: Yes
TestCab: 0x0
LegitcheckControl ActiveX: N/a, hr = 0 x 80070002
Signed by: n/a, hr = 0 x 80070002
Product name: Windows 7 Professional
Architecture: 0 x 00000009
Build lab: 7601.win7sp1_ldr.160408 - 2045
TTS error:
Validation of diagnosis:
Resolution state: n/aGiven Vista WgaER-->
ThreatID (s): n/a, hr = 0 x 80070002
Version: N/a, hr = 0 x 80070002Windows XP Notifications data-->
Cached result: n/a, hr = 0 x 80070002
File: No.
Version: N/a, hr = 0 x 80070002
WgaTray.exe signed by: n/a, hr = 0 x 80070002
WgaLogon.dll signed by: n/a, hr = 0 x 80070002OGA Notifications data-->
Cached result: n/a, hr = 0 x 80070002
Version: N/a, hr = 0 x 80070002
OGAExec.exe signed by: n/a, hr = 0 x 80070002
OGAAddin.dll signed by: n/a, hr = 0 x 80070002OGA data-->
Office status: 109 n/a
OGA Version: N/a, 0 x 80070002
Signed by: n/a, hr = 0 x 80070002
Office Diagnostics: 025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3Data browser-->
Proxy settings: N/A
User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)
Default browser: C:\Program Files (x86)\Opera\launcher.exe
Download signed ActiveX controls: allowed
Download unsigned ActiveX controls: disabled
Run ActiveX controls and plug-ins: allowed
Initialize and script ActiveX controls not marked as safe: disabled
Allow the Internet Explorer Webbrowser control scripts: disabled
Active scripting: allowed
Recognized ActiveX controls safe for scripting: allowedAnalysis of file data-->
Other data-->
Office details:{163752C2-0AB7-4A81-9190-57AC32A7D366} 1.9.0027.0 6.1.7601.2.00010100.1.0.048 x 64 *-*-*-*-PW487 5 S-1-5-21-1838812046-2382835335-2825030358 the system manufacturer ,System Product Name American Megatrends Inc. 00371-177-0000061-85051 3604 20120223000000.000000 + 0001EEC3907018400FE 0416 0416 Hora oficial Brasil(GMT-03:00) 0 3 109 Content Spsys.log: 0 x 80070002
License data-->
Versão Serviço licença software: 6.1.7601.17514Name: Windows 7 Professional edition
Description: operating system Windows - Windows (r) 7, retail channel
Identificacao da Ativacao: e838d943-63ed-4a0b-9fb1-47152908acc9
Identificacao da size: 55c92734-d682-4d71-983e-d6ec3f16059f
Estendido PID: 00371-00170-177-000006-00-1046-7601.0000-0242016
Identificacao da Instalacao: 011474361013629363953701508091790880199835132104999472
Do Certificado Processador URL: http://go.microsoft.com/fwlink/?LinkID=88338
URL Certificado da Máquina: http://go.microsoft.com/fwlink/?LinkID=88339
Da licença of Uso of the URL: http://go.microsoft.com/fwlink/?LinkID=88341
URL do Certificado da Chave Produto (product key): http://go.microsoft.com/fwlink/?LinkID=88340
Chave Produto (product key) Parcial: PW487
Status da licença: calculated
Razão da calculated: 0xC004F009 (o periodo Armony expirou).
Contagem remaining rearmacao do Windows: 0
Confiavel Hora: 14/07/2016 13:31:27Windows Activation Technologies-->
HrOffline: 0x00000000
HrOnline: 0xC004C532
Beyond: 0 x 0000000000000000
Event timestamp: 7:14:2016 13:23
ActiveX: Registered, Version: 7.1.7600.16395
The admin service: recorded, Version: 7.1.7600.16395
Output beyond bitmask:--> HWID data
Current HWID of Hash: PAAAAAEABgABAAEAAQADAAAAAgABAAEAln36/sIWNidiNErd9OPg2 + oC4DRyVhqAumU + k7dYSBLGni5zActivation 1.0 data OEM-->
N/AActivation 2.0 data OEM-->
BIOS valid for OA 2.0: Yes, but no SLIC table
Windows marker version: N/A
OEMID and OEMTableID consistent: n/a
BIOS information:
ACPI Table name OEMID value OEMTableID value
ALASKA APIC HAS M I
FACP ALASKA A M I
HPET ALASKA A M I
ALASKA MCFG A M I
SSDT IdeRef IdeTable
SSDT IdeRef IdeTable
SSDT IdeRef IdeTable
ADELINE ALASKA A M IAnd I can't press the button 'solve '. Could you help me please?
PS: I downloaded all of the Opera browser, also, I am of the Brazil.
My father lost the key. But I managed to post anyway. I did this: before, my computer has lost its properties of activation, I saved the installer of Windows 10 and then, I got a Windows 10 key program necessary to update to Windows 10, and now she's authentic. But thanks for the help guys! Should I delete this post or something like that?
-
problem with the activity indicator
Hi, I can show activity indicator. But the problem is that I do not know how to deal with another task. I have a screen that show activity indicator and then the application displays this screen is run an initial process to build the database in the SD card. I tried with a thread, but did not work and I have seen other examples, but without success
Thank you
You might find this useful:
Look for the update in the commentary. I think the approach that corresponds to what you are looking for.
-
Pool pane there problem with long sql query?
Hello
I use Jdeveloper 11.1.2.2.0
In the application I'm developing, there is a long sql query to call (it's a function from a package, which may take a few minutes to run) and I want to display a progress bar for the user.
The progress bar component is a "progress indicator" and the percentage of achivement is refreshed by a component 'pool' with 1-second interval.
The two components are connected in a javabean.
The function with the sql query is the javabean too.
To run the sql query that is long on background I am calling from a thread, and the pool component get the advancement of the percentage of a pipe filled with the sql function.
If the function to run is just a long loop of java operations the progress bar works fine, but if I put my long sql query instead, stop listener pool should be performed to stop long, s sql queryo progress are updated only at the end of the long sql query.
You have any ideas?
Thank you
Thanks for your replies. Unfortunately, it was not the solution to my case, sql procedures to block the entire application while ADF awaits them at the end...
To solve my problem, I finally used a PL SQL Job to call my sql procedure (dbms_job.submit).
The application is released right after the call and the component of the pool is not more secure!
Kind regards
Yann
-
problem with the activation of the lists?
I continue to enjoy to find and collaborate with ICE. It works very well with the customer, with the fact that I'm testing.
I encountered a small problem that I can't solve. Initially, I didn't create ordered and unordered for my client lists. But they wanted to create lists bulleted on a particular page, so I checked the box for this and uploaded to the page with the parameters of ice published. However, the bulleted in the ice button is always disabled and a list cannot be created on the page.
The clues why? I have re-uploaded and connected to several times to be sure I was working with an outdated version of the page.Dig and experiment a little solved the mystery. For anyone who runs into the same problem...
There was a project already in process at the time wherever I activated this ice editing capability. I guess that the project is based on the editing at the time parameters wherever the project was done. That's why when you edit a project, it uses the same parameters. Rejecting the project and re - download page with the updated ice settings and then do a new edition worked in adding a list.
-
I bought Parallels for my Macbook and moved my Windows to him, but after a month or two, I was invited for a product key that I have written, but was rejected and I have since then been locked my window and my data lost as a result, I have an installation disc and product key that I "KNOW" is correct doesn't work ' ". Someone please tell me what the matter, is because I'm seriously at my wits end.
The problem is not a software but a licensing of one.
Your existing OEM license cannot be transferred to a new machine--and it is difficult to do a upgrade to a non-genuine system (by design).
You always have your machine 'physical Windows' available? He's still in the original configuration that you want to transfer?
Apply you the full Ultimate who license and activate it, then repeat the virtualization
The new virtual machine will still complain of activation status initially, but you will be able to reactivate in the virtual environment.
You then have to take back the physical machine to the Home Premium of origin by a reinstall license using recovery madia or sale at retail or restore an image from before the upggrade.
Maybe you are looking for
-
My temp folder is locked on read-only. I tried to disable it in safe mode and nothing seems to work. I checked for viruses using a deep scan in SafeMode cmd and nothing was found. I use Windows 7 and can't install a backup drive or update all program
-
password reset does not work here
OK, I use OPERA browser because Firefox will not get past the password on this site!Tried twice and still no SOAP, he seems to accept the change of password and asks even if I want to remember, but won't let me sign in! What is the problem?Firefox 24
-
Hello I have a portege R100, which, with the new 1 GB memory is very good. I want to update from XP to Win7.All the world does? Any suggestion? Win 7 slow down the system? Richy
-
T420-best SSD for use in housing Ultrabay caddy?
What is the best SSD for use in the Ultrabay caddy in a Thinkpad T420?
-
Why data acquisition in an executable collect fewer samples?
Hello I have LV2012 on Windows and SMU-6341 map in PXI chassis. I have a task for the acquisition of data on I-1 on my monstrous application. Well, to get to the point, I have here a case where the task of data acquisition starts, waiting 20ms, reads