Talk when you touch

Similar Questions

• Satellite M30X powers off the power when you touch the USB port

  Hello everyone, just registered and it is the first problem:
  As there is no general hardware forum, I post my problem here.

  I got it twice, my laptop
  (Product: Satellite M30X, Version: PSA72E - 008010GR) just went completely off.

  Motherboard:

  NorthBridge: Intel i855GME
  SouthBridge: (ICH4-M) of 82801DBM LPC Interface Bridge
  Motherboard model: Toshiba EAL20

  USB:

  82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI controller #1-3
  Version: 1.0
  Interface: UHCI
  Frequency: 48 MHz

  82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB 2.0 EHCI controller
  Version: 2.0
  Interface: EHCI

  I have the latest Intel Chipset drivers installed and Windows XP Home SP3 with all updates.

  Once when I hit just the back USB ports with a USB plug, the other time when I unplugged my bluetooth key (climbing din't remove it).
  There was no blue screen or message of any kind, not even in the registry after you start the system again or this fatal system error box when you start after a system error.

  Just a total failure. But it works fine the rest of the time. I also tried to remake the script, but it didn't work.
  I have cleaned with a vacuum cleaner to remove dust and has taken a good look, but saw no difference to the side track.
  Maybe the clamps of the wand to shield a little more out to the contact pins on the rear.

  What bothers me a bit, it's some time ago, I had the laptop one computer my knees and I forgot that a memory stick has been connected to the rear. The stick was pushed up and was slightly damaged.
  Still works well. Now for me, that I broke the USB port Insider somehing.
  I could not determine also the loose parts or unfirm at all.

  Y at - it there, diagnostic software that measures the motto of the port or power problems?
  I have a multimeter, fetch short-circuits with it?

  I saw a package of drivers Intel for USB 2.0 over there, but I can't find it on their page, advice?

  Thank you very much for your help, I just wanted to update my RAM and now I am not so shure if my laptop will last the next week.

  Fabian

  Hello

  I put t know any diagnostic software that could analyze this question, I think that a technician of the ASP may be able to provide exactly this question results

  > What bothers me a little is that some time ago, I had the laptop and my knees and I forgot that a memory stick has been connected to the rear. The stick was pushed up and was slightly damaged.

  I think this might be the reason why the laptop stopped while you touch the USB port eventually ports were damaged by using the memory stick, this could cause the laptop off

  However, what we can do is to provide some suggestions and assumptions
  It you want to know why this is happening exactly, then you need to contact a technician laptop for a control.

• I have suddenly a window talking when you watch a videao-how to cut?

  How to disable Firefox speaking voice who keep me talking about the 'new window Firefox' and all move and click on that I do.
  I was not able to find a way to silence the voice.

  It is an operating system feature called VoiceOver. The key combination command + F5 activates this power function.

  You can also in the Apple menu, select System Preferences, then click universal access. Select the Seeing tab and you should see a setting to disable VoiceOver.

• reduction of severe frame rate when you touch the screen, iOS

  Hello
  I have a simple app with scroll to the top of the stage with a bitmap image in each of the clips of 2000. They are moving incredibly fast at 60 fps.
  But the moment that I even put a finger on the screen the fps drops to about 40 if I move my finger it drops to 30 fps.

  is this a normal behavior?

  There is no listener of events or something like that.

  Thank you :-)

  I did a couple of things that have improved the framerate:

  mouseEnabled = false;

  mouseChildren = false;

  No movieclips, only bitmaps, perhaps of sprites.

  If you use clips for controls, make sure that they are not nested in a different movieclip that covers the entire screen. (avoid nesting where possible)

  delete text text_input fields

• Why Photoshop stop when I touch the touchscreen on the lap top and I can avoid it?

  Every time I start Photoshop you stop with this message below saying that it has stopped working. I realized that it stops when I touch the screen. How can I avoid this and it is possible to work in Photoshop using the touchscreen?

  

  It is not normal that photoshop to complete when you touch the screen. Either something with photoshop is corrupt or the driver for the touch screen.

  First thing to try is reset the photoshop preferences. CTRL-k on windows or cmd - k on a mac, and at the bottom of the Panel is a button to reset the preferences.

  If this does not work, uninstall photoshop, restart your computer, reinstall photoshop.

  Next is to see if you can update the driver of the touch screen. Sorry I don't know how to do and would depend on if your windows or mac and what version of the operating system that you use.

  Finally run CC Cleaner

  http://helpx.Adobe.com/Creative-Suite/KB/CS5-cleaner-tool-installation-problems.html

  This will remove all traces of Adobe programs on your computer. Restart the computer, and then reinstall the Manager then photoshop.

  I hope that one of the above will solve your problem, if not let us know.

• How can I stop my pages to change (moving paragraphs breaking, chapters) when you try to export?

  I am pretty new to indesign and self teach me through the internet and books. I'm working on a new layout and I had finished what I thought looked nice. The final step was to export to a PDF format, I thought. Well, when I export and then see the PDF a few paragraphs are broken by a few lines between the first part and second part. Chapters also lose their position. I go back in InDesign, and check and it would be what was in indesign as well. I've fixed a dozen times. Double and triple checked the pages before again hitting the export. Once again, more trouble, but it would be in different places. I do something wrong when exporting?

  Did you start this book in a version earlier if InDesign and convert? If so, the text engine is different in the new version and stories of reflow when you touch them somehow. You can force ID to recompose all stories by using the shortcut Ctrl + Alt + / Windows or Cmd + Opt + / Mac, then check carefully through all this.

  You can also force a restructuring by exporting to .idml and opeing, then saving it under a new name. (See delete minor corruption by exporting)

• When you use Itunes on my Ipod Touch 5 generation, the Ipod is no longer automatically past from one song to another. This seems to be a novelty. There is a button on the RIGHT side of the upper third of the screen where you can choose options but go n0.

  When you use ITunes on my Ipod Touch 5 Gen, running IOS 9.2, he has recently stopped automatically switch a song on one album to another while listening to ITunes. I discovered a button with 3 points to the RIGHT side of each title of the song which, when typed gives a different options for example then played, add up to the next etc.. If you use these all this seems to get worse with more choices that appear. I know that sounds incredible, but I have owned several Ipods that I use just for listening to music. Mine is a 32 GB version that can store a large number of albums, most of which I bought and loaded into my Ipod. A few albums that I downloaded from ITunes. How can I get it from my Ipod to listen to music in the ITunes application without having to select one of the 55 options?

  See if the chapter of the music of the Manual:

  http://help.Apple.com/iPod-touch/9/#/iph3bd017b9

  Next:

  -Reset the device iOS. Nothing will be lost

  Device iOS Reset: Hold down the On / Off button and the Home button at the same time for to

  ten seconds, until the Apple logo appears.

  Unsync/delete all the music and Resync

  To remove all music go to settings > general > use > storage > storage management > music > tap Edit in the top-right, then press the sign less than all music

  -Reset all settings

  Go to settings > general > Reset and tap reset all settings.

  All your preferences and settings are reset. Information (such as your contacts and calendars) and media (such as songs and videos) are not affected.

  -Restore from backup. See:

  Restore your device from an iCloud or iTunes backup - Apple Support

  https://support.Apple.com/en-us/HT204184

  -Restore factory settings/new iOS device.

• When you use the touch pad, the pointer would not move.

  Original title: arrow not laptop computer movingon

  When using the touchpad on my laptop the pointer would not move so I had to plug my mouse to use my laptop. Why the touchpad pointer stopworking?

  Hi Ron123,

  1 Windows operating system you are using?

  2. What is the brand and model of your laptop?

  3. This occurs when you use a particular application?

  4. When did you start to question?

  5. did you of recent changes to the computer?

  You can try to update the latest version of the Touchpad drivers from the manufacturer's website and check.

  Updated a hardware driver that is not working properly

  Hope this information is useful.

• Error in get LV class by default when you open the default printer

  I am using vi text report easy to print text to the default system on a touchscreen Windows XP Embedded PC printer.

  When I run the simple VI I wrote (attached) I get a file not found error 7 in the LV ranks default vi when new report vi is called.

  The path in the default on the LV class value get's strange appearance; Here it is:

  c:\Torqo\USB Example.exe\1abvi3w\vi.lib\Utility\NIReport.llb\Standard Report\NI_Standard Report.lvclass printer

  The first elements of the way little look OK - player C and file Torqo that I'm short and the name of the application. Then it seems really weird.

  I use remote debugging on the touchscreen integrated for XP but it has the same error if I just run the .exe on the touch screen

  I can open Internet Explorer on the touch screen and print from it to the default system printer (it's an Epson printer).

  It smells kind of some package DLL or runtime package is not loaded on the touchscreen - but what it could be?

  I loaded the LV 2010 Runtime Engine LVRTE2010std.exe and the VISA DURATION visa503runtime.exe

  My vi normally works on the development of Windows XP SP3 without error System.

  In turn is a simple way to imitate printf or print serial port inside Labview, only to a USB port?

  I just need simple ASCII text that is sent to the connected USB printer.

  Any ideas for me?

  What's with the weird class path?

  I am a fairly new LV programmer but a Windows .NET programmer for a long time.

  Thanks in advance.

  I have no experience with the help of LV with XPe, so I can't help you there, but I can talk about the way - the EXE is essentially a folder structure that has been compressed into a single file. Inside this structure, LV place shipping screw in a folder called 1abvi3w so that they can be referenced by using a logical path (1337 is to avoid potential collisions).

  The only thing that I can suggest the hand is that you go into the build specification and explicitly include the report class when the generation by adding it to the section to always include. Theoretically, this happens automatically when you use the class, but maybe something is malfunctioning? Perhaps XPe does not pathnames within files exe or dynamics of decompression of the EXE file?

  If this does not work, you can also change the specifications of construction to place the report class at a specific location outside the EXE or go to the Advanced page and set the build to use the 8.x - style paths, which could help you, because I believe that it should generally put classes to report outside of the EXE.

• When you move the cursor, rather than move, the police often changes a size big or too small to see.

  Original title: "when I try to move the cursor, instead of move, the font size often changes to a huge size or one size too small to see. In addition, it can jump to the top or the bottom of the page. »

  More I use Vista, more I hate it!

  It came pre-loaded on my Fujitsu Lifebook. I had heard talk were many complaints about Vista and I wanted to stay with XP or Windows 7.  Each manufacturer of the laptop has been unfortunately Vista preinstallation.

  • When I use the word processor Works Windows, sometimes without warning he automatically becomes italic police without any input from me.
  • If on Windows works WP or on any page of e-mail online, when I starts to move the cursor, a little 'target' - as the icon appears when the cursor was and, either changes in font size of microscopic or 500% or more.
  • On the Internet page of wole can shrink or get huge.
  • At other times, with one touch of the mouse or touchpad, rather than the font change, the cursor may disobey my entry and the end to the top at the bottom of a page where I won't be, or somewhere else. When I get back to the expected location, it can repeat the same action three or four consecutive times before to behave normally again.  This makes typing manuscripts or very frustrating messages sometimes, not to mention a lot of lost time.
  • When you try to type copy from a printed script, if I don't keep control of the screen I can finish with margins stange, italic where they belong or phrases that are moved where they belong.
  • Sometimes when I'm trying the high - lite a word or phrase so I can drag it to another location, it will refuse to high light, making necessary use rear brace to delete the words I want to drag and retype the words to the new desired location.
  • Another problem is that the will of cursor down stubornly and turn several times since the location of the Center to the extreme side so that the rest of the page is covered.  Vista seems to have a mind of your own.

  This set of problems seems to migrate from MS Word to MS Works, Web pages, and e-mail message composition.  I thought it was the new computer initially. I even returned it to Fry's electronics for maintenance two times.  I mean, they just excanged for another new Fujitsu Notebook.  When I got home, the replacement computer have behaved in the same way, which indicates that it's the software, not the hardware.

  Funny thing - now that I complain on this topic in this forum and have written this much, it doesn't have behaved badly again!  The ghost of Vista must have been scared and went into hiding.  ;-)

  Yet once more I use Vista, more I hate it!  -especially since I was in the middle of writing a book for publication.  In light of the frustration and the loss of my precious time because of these persistent bugs in recent months, I wish MS would trade my copy of Vista for Windows 7.  MS seems to be getting a reputation for releasing Beta quality software and call it a finished product.  You would think that MS wakes up to the fact that consumers expect to have for their money.  Everyone has the same problems?

  Are there realistic solutions out there?    Hmm, no spell no checker on this page.  Sorry for the typos. :-)

  You can get in trouble with your mouse device drivers, firmware and/or software.  This may be due to a Microsoft Update or any number of things (and could have happened to these two machines, if you did the same thing in both cases).  Go to the Device Manager by going to start / find and type Device Manager and enter and then double-click on the program icon that appears.  Check each device to a red x, yellow! or white?  These identify devices with problems probably (drivers, but also of conflict or something else).  Click on each for more details and troubleshooting tips.  If you need to get drivers (and you should get for your mouse at the very least and I consider the keyboard as well and make sure they are compatible with your device, and your version of Vista) and all you have time to do - they can help way beyond simply solve this problem) leave the computer dealer or the manufacturer of the device (NOT of Microsoft Updates).  In fact, you must disable automatic updates in Windows Update driver as follows:http://www.addictivetips.com/windows-tips/how-to-disable-automatic-driver-installation-in-windows-vista/. Follow these steps to get the drivers: http://pcsupport.about.com/od/driverssupport/ht/driverdlmfgr.htm.  Once you have the drivers, you can install them via the Manager device as follows:http://www.vistax64.com/tutorials/193584-device-manager-install-driver.html.

  Also, your mouse may have the functionaality to change the font sizes and jump from one end of the screen to another by doing some things.  Read the user manual and/or research through start / Control Panel / mouse to see if this is the case and if so, it may be able to be disabled.  The problem with some of these "features are that if you don't know about them they can cause difficulties when they activate for apparently no cause when you actually not what caused the feature must be enabled." It took me a while to realize the CTRL-0 would change my IE screen at 100% size and I first thought there was something wrong until I discovered the problem by chance.  I say that, because the odds of two computers with the same exact defect are astronomical - it looks more like a problem as described above or a certain type of function you are unaware of (perhaps in combination with a keyboard input that is why I suggested that you update those as well).

  I hope this helps.  If not, I am sorry to say that your best option would be to go back again to see if they can reproduce the problem (you use your way computer in case it is something you do) and either repair or replace again (or change to another computer entirely).

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Woman updated its iPAD Pro 10.0.2 and is now locked screen display "Enter Access Code, contact ID requires your access code when you restart the iPad." She has no idea what is an "access code". Any help is appreciated.

  Woman updated its iPAD Pro 10.0.2 and is now locked screen display "Enter Access Code, contact ID requires your access code when you restart the iPad." She has no idea what is an "access code". Any help is appreciated.

  If she don't remember: If you have forgotten the password for your iPad, iPhone or iPod touch, or your device is disabled - Apple supports

• I improved my 5s IOS10 3 days and battery discharge excelerated standby, as well as when you use. I turned off notifications, as, other non when not in service. Which could operate in the background?

  I improved my 5s IOS10 3 days and battery discharge excelerated standby, as well as when you use. I turned off notifications, as, other non when not in service. Which could operate in the background?

  Hi mweedn!

  I understand that you see a reduction in the battery of your iPhone 5s after updating to iOS 10. It is important to be able to make full use of your iPhone! There are a few resources that can help.

  Before the resolution of the problem, were you able to view information using your battery on your iPhone? Here's how to check the amount of battery used by each application:

  On the use of the battery on your iPhone, iPad and iPod touch

  When you answer, remember to let us know if you see all the apps with an abnormal amount of battery. See you soon!

• I have problems when you try to use a current OSX on my Mac eco system, causal link - specific needs on the three or four main applications.

  My systems include the MacMini, MB Air, Pro MB [all 2011] on OSX 10.8.5 Mountain Lion, with a MacMini extra [2011] with the help of El Capitan (for the purposes of the trial) as well as an iPadAir2 and an iPhone - both on iOS 9.

  I joined the eco system (from Windows) Mac to Snow Leopard and fortunately this used for all my needs. moving through the Mountain Lion and Lion (quickly), where I is a happy user!

  Failure to make progress in terms OSX is the result of...

  1. my extensive libraries of pictures were worked on - and are still being held in - iPhoto ' 09 (8.1.2) - which met my needs exactly - I have many albums which photos should be sorted manually - that is to say, not by Date, the former/Newest or title!  So, the current Photos app does not work as well for me on for my Scrapbook sort, although apparently it allows the movement only photo by mouse?
  2. I made 'heavy' use of iCal using many individual alert entries (!) of my choice as to the date, time, etc. and not very limited alert options offered by the newer versions (iOS-like) to iCal, where I use the alert custom-making every time! I avoid editing or for alerts in iOS 9 because o f the limited options available.
  3. I am a user passionate worksheet and delayed moving on numbers of Excel. I moved platforms for Cougar and live joyfully on numbers now with stored copies online as well.

  Tempting to work in El Capitan, I am "forced" to spend my worksheets to the most recent numbers app when I come to save and cannot then use the 'improved' version recorded on my systems of Mountain Lion (where I still pure copies!) -similar events occur when you use Pages; the lack of recoil connectivity is a major drawback for me that I apparently must keep OSX Mountain Lion to use my key apps 'base' to meet my needs!

  Are there workarounds 'smart' (or applications) that will overcome all (or part) of these "disadvantages", allowing me to good progress and update on El Capitan OSX (and Sierra at the right time)?

  I have to start using a different calendar system to have the usable alert options (which deviates from the eco system) systems on the scale?

  Should I go back to using Windows Excel (or Online) to my spreadsheet to have facilitated cross-OSX usage?

  Thank you.

  On applications of numbers and Pages, there is a real problem if you need backward compatibility - alas, I don't have a solution for you.

  But I do not understand what limits you talk in calendar alerts. I can add events and alerts for them in El Capitan (and now Sierra) using the same methods that I used in previous versions. I can receive messages, sounds or emails in any number and both custom of my choice. Can you serious? Maybe post screenshots of before and after? I'm not available for the comparison of older systems. There are indeed limits if do you the same thing in iOS, but AFAICT not on the mac - and, especially, the alerts personalized on the mac are correctly transferred to the iOS device that I use (an iPhone), to my first mac.

• TB 31.0 when you reply or forward, will not allow the names in TO:

  With the help of TB 31.0. When I hit the reply, no name is inserted in the TO: and does not have a name to register. When you use before, does not allow a name to be included in the TO:

  Problem started after the installation of 31.0 TB.

  Start in safe mode (hold SHIFT (Mac: Option) when you start TB) and see if the problem persists. You have the add-on Photo touch?

• TB crashes when you delete e-mail messages. Only the anti-virus is Windows Defender.

  When I click on an e-mail message and click one of the buttons < delete > the little blue circle lights up and I get a message "(ne répond pas)". " This is a < delete > click for the line of a message. Usually occurs after removing a few previous emails

  24.4.0 TB. Windows8.1. Windows Defender. All up to date.

  I checked. Do _not_ have McAfee, Norton, Avast, etc. system or in the form of modules.

  Tried to reboot Windows 8.1. a couple of times. Problem remains.

  Your initial problem was talking about freezing when you delete messages from Thunderbird.
  Still you see that now?