Tecra 720cdt: screen is central docking station - 1/2 in.

Similar Questions

• Tecra M5: Double monitors with docking station?

  Hello

  I have a Tecra M5 with docking station, in the past with other laptops, I was able to hook up a monitor by using the analog port and the other with digital and used both with the screen down.

  This seems not possible on this new, I have options to perform a monitor with the laptop or with a TV screen, but not two monitors to separate whole.

  Everyone was able to get this to work if so how? Graphix is the NVIDIA Quadro NVS btw.

  Thank you

  Hello

  It is very interesting, but all I know is not possible. I'm not sure at 100%, but for something like that you need a special graphics card that supports something like that.

  The same situation is with my Tecra. But the idea with two external displays is not bad. :)

• HP EliteBook 8570w: is it possible to run two monitors on a 8570w without a docking station.

  Is it possible to run two monitors on a 8570w without a docking station. Connect a monitor to the VGA port and the other to display port.

  I was able to get this to work. My 8570w has an Amd over-pants 7700, don't know if that matters. One is connected VGA other Displayport. The port monitor must have a custom resolution defined in the over-pants Control Panel. except that it works perfectly. More laptop screen no. Docking Station 2 24 inch Dell.

  And thanks for the quick reply Provost.

• Tecra A10 - 1GV and Docking Stations: Dynadock vs Express Port Replicator II

  Hello Forum;

  Official Toshiba site proposes to use the Docking Station Express Port Replicator II for laptop A10 1GV.

  I need for my construction work 2 monitors.

  My question: can I use with the Express Port Replicator II two additional monitors at the same time (there are 2 connectors (DVI and analog VGA/RGB). Is it possible to create two different images in this way?
  Some have said, that after a connection with the DVI - D VGA connector is turned off.

  Someone at - he experiences?

  On the other hand Toshiba offeres the Docking-station "Port replicator USB Dynadock U" -.
  This docking station is only connected via USB with the laptop. According to the data sheet - it provides an analog and a digital monitor with different views at the same time, up to 1920 x 1200 pix., extra headphones and 6 x USB 2.0. more network connection

  This official docking station works with all USB-connect computers, but in the compatibility list does not mention the Terca A10 and gives only a declaration of compatibility for the series Toshiba NB200 from Toshiba.

  Someone out there experimenting with this docking station?

  What would be the best way to work with two monitors + the computer screen?

  Thanks for all the good advice.

  Michael

  Hello

  As much as I know Express Port Replicator supports the simultaneous use of RGB & DVI only if the laptop itself also supports the simultaneous use of RGB & DVI.
  So if the Tecra A10 1GV would support the use of RGB and DVI port simultaneously then Express Port Replicator should support too.

  The Port USB Dynadock Port Replicator support VGA or DVI port. I didn't find the Dynadock, which was equipped with two ports together.
  The Dynadock can be connected to all computers with USB 2.0 and it beautiful s expansion.

• Tecra M9 - save the settings of display with docking station

  Hey there.

  I have a user who has a Tecra M9 on a docking station.
  There are 2 monitors connected to the docking station with VGA, the other with DVI. I use the Nvidia Control Panel and configure the screens and all is good in the world.
  That is until the user off the laptop, some work at home, then puts the laptop in.

  Therefore, only one monitor works, with the second out of action.
  I can go back and reset the configuration, but the user does not want that to happen every day.

  Any suggestions on how to get the laptop to save your setting as the case not docked or anchored?

  Thank you!

  > That is, until the user off the laptop, work at home, then puts the laptop in.
  Do you know what the user did in the past?
  To my knowledge there is not any special options that could save it. If you click on the button (apply) the changes are made and recorded.

• Tecra M9-104 with docking station - DVI resolution

  I wonder if anyone can help. I have a Tecra M9 - 104 running Windows XP. I also have the docking station to go with it. The great thing about the docking station, it's that it can out to two screens as the port on my M5 Replicator could not do.

  I bought two identical external screens that have a native resolution of 1440 x 900. I went into the Nvidia display configuration and set up to display both (one is plugged in VGA and one DVI port). However, the display on the DVI monitor is wrong. After further investigation I woke up the menu of the monitor on the screen to see that the resolution actually be issued is 1280 X 1024, despite Nvidia screen saying 1440 x 900 has been the output. Whatever I do, I can't increase the resolution on DVI port.

  The only thing I could find on Google and these support forums is that the maximum resolution on the DVI port on a port replicator is 1280 x 1024, but it was for the M1 and M2 series. This laptop is the last series and as such, I expected that the spec had been updated at this time.

  Someone at - it ideas?

  Could be due to a limitation of the video driver on the laptop, or you can try to download a utility that requires to use a different resolution, its called Powerstrip (do not have a download link sorry).

  Be careful with it though, you can mess up your video driver

• Tecra M2 not to close on docking station

  I have a Tecra M2, of which most of the time is used in a docking station. However if I'm on the docking station for laptop computer does not shut down (it sticks to the "Windows is shutting down" screen... unless I have physically remove the laptop from the docking station, and then he finished the process to close.)

  If the laptop is not on the docking station, there is no problem of closure.

  I tried to remove all the devices that are connected to the docking station, but that makes no difference.

  I use v3.65.00.XP Toshiba Mobile Extension.

  Also note that I do not and never have been, a 'disconnect the computer' as an element of Start Menu (there also no "NoStartMenuEjectPC" button anywhere in the registry.

  One last thing; If the laptop is cold (IE only used for a few minutes), then it will sometimes close ok on the docking station.

  Any suggestions very welcome.

  Tennant

  Hello

  It is not easy to give you a good explanation, but you can try to reinstall the mail Mobile Toshiba is perhaps also an application that runs in the background, the reason for this.

  Your device comes preinstalled with recovery DVDs?

• Tecra A10 - change of resolution with Docking Station problem

  Hello

  I own a Tecra A10 - 14Q and I like it a lot - it is a very beautiful piece of hardware, including the functionality of UMTS.

  When the Tecra is moored to the dock Express, and the external monitor (Samsung SyncMaster 22 "with resolution 1600 * 1200) is on defining the Office to be cloned on both screens, passes resolution of 1280 * 800 on the Tecra to 800 * 600 as"best resolution.

  I tried Intel and Mobility Center graphics settings, but I can't find a way to set I want to keep the resolution 1280 * 800.

  Suspicion to do so automatically is welcome. I found that a program that now lies on my desk that I run so it redefines the resolution to 1280 * 800, but I would like to stress that resolution remains just that it is.

  Kind regards

  YaGru

  Hello

  It's not easy to say why the resolution automatically decreases

  But sometimes, if the external monitor would be connected to the Tecra A10 directly without using the Express Docking Station?

  Otherwise the problem could be linked to the dock Express (Replicator of port express?)

  Maybe the 1600 * 1200 resolution on external monitor is too high for the express port replicator and so there are some questions which s my personal suggestion

• Tecra M11 - 17V - identify the serial port on the docking station

  I have a laptop Toshiba Tecra M11 - 17V, which I often use with the docking station that accompanies it.
  There is a DB9 serial port at the back of the docking station, but I don't know what COM Port.

  I use Windows 7.

  In the device, COM9 Manager - COM22 are identified as Port BT (bluetooth). Com7 - COM8 are RIM Virtual Serial Port v2, COM17 is Prolific USB-to-Serial Comm Port and COM18 is USB-Serial CH340.

  I thought that COM17 or COM18 were the most likely candidates, but have not been able to get to answer using one of them.

  I connect a Psion 5 (Comms app) to him and have developed ports and the Psion 8bits, 19200 baud, no parity, 1 stop bit.

  Hello

  > There is a serial port DB9 on the back of the docking station, but I don't know what COM Port, it is

  I think you have misunderstood something wrong
  COM ports in Device Manager are virtual com ports
  There is no link between a serial port and a virtual com port.

  I have a question: what docking station you have exactly?

  I had an express port replicator and this device required an additional serial port driver installation.

• HP 2008 120W Docking Station (KP080UT) Support screen double

  The Station of host HP 2008 120 w (KP080UT) supports two screens?  If this is not the case, what docking station will be?

  I tried to run two monitors connected to the docking station with a portable computer stock HP Compaq 6715 b.  A monitor is on DVI, the other is on VGA.  Single screen works individually on both DVI and VGA, but together, it won't.  The laptop sees there is a second monitor, but when I said "Extend my Windows desktop on this monitor." the first monitor flickers as its going to change everything, but goes back to the single screen.  I updated the graphics drivers and tried with both open and closed laptop.

  Support Online Chat told me that it depends on the graphics card.  6715 b is not compatible double screen.

• External monitor like main screen for M200 with docking station

  Hi all

  I have a Tablet M200 with GeForce FX go 5200. I have a Toshiba docking station and an external LCD display. When it is docked, I would use the external LCD as main display and the LCD builtin as the secondary display. (I want the taskbar, icons and newly opened windows on the external screen when it is docked.)

  Unfortunately, I can't find the right combination of settings of this. If I put Windows to extend the desktop on the external screen, "use it as primary display" option is grayed out. I don't get the span horizontally or vertically options in the nView utility, just the Standard and the Clone (and this only if I do not extend to the office.)

  How can I get the external screen be the main while being the internal school?

  Thanks in advance!
  Kind regards

  Levente

  Hello
  What home-unit station use?

  Tablet Multi dock PA3315E-1PRP or Port Replicator advanced III: PA3314E?

  thx for the info,

  Good bye

• Docking station for Tecra M5

  If there is a docking station (universal or special) for Tecra M5 laptop computers?

  Rgds

  Hey

  What do you think of a Dynadock?
  There's a Dynadock who takes in charge a VGA (PA3541E-2PRP) or DVI (PA3542E-2PRP) port.

  Otherwise I recommend to use an Advanced Port Replicator III more PA3474E-1PRP which is compatible with the Tecra M5.

  Google just for the part number and you will get some info on the Advanced Port Replicator III more

  Welcome them

• PROTECTED R700 on docking station / command screen

  Hello

  I'm on a Toshiba protégé R700 on a docking station and I have problems in installing the screen of the built-in or external.
  Is it really necessary to press FN + F5 to switch the view when the apparatus?

  My scenario:

  Laptop on the dock, using external display
  Stop Windows XP
  Undocking
  Laptop computer startup
  Enter my Login of Win XP on the logon screen
  Built-in screen turns black

  After that I have to press FN + F5 blind or are anchored the laptop to change the setting on my external screen.

  > Is this really necessary to press FN + F5 to switch the view when the apparatus?
  Hmm Yes it of necessary to press FN + F5 to switch back to internal laptop display if you have previously used the external display

  The Fn + F5 switches between the internal and external screen... so you must use this option if you want to reuse the internal laptop display.

• Tecra M10 - 17 H no support DVI via docking station not

  There is already a message asking this, but I wanted to point out that it is a problem affecting more than one user.

  Too, I bought a Toshiba laptop for my business as it was supposed to be a laptop a serious matter. However, I must say that I am losing confidence that Toshiba understands what needs a company.

  The docking station is frankly a joke. USB KVM will not work with it, probably, there is no PS2 port you can not use a KVM PS2 instead. Even if you could, the VGA dock does not detect the external VGA is present when there is a KVM. Of course, the answer is "simply" open up the laptop and set it up on the Panel, then switch to external whenever you turn it on. How can anyone think that is a response in a business, or any other environment is beyond me.

  Now, I find that my laptop has an Intel graphics card I can't use the DVI port on the dock either. Which is really annoying, is that I could buy a laptop at half price, but wouldn't because I wanted a laptop class business that disintegrates not in respect of the use. I didn't pursue a fantastic graphic option because I did not doing anything fancy either, but graphics without the supported DVI via the dock is just simply ridiculous.

  Now, I regret bitterly, to get rid of the old Dell D/Dock that although several years worked without fault and with DVI, with any old KVM and without any problems at all.

  Sorry for the mug shot, but I am bitterly disappointed that I bought a cheap puppy that I can't afford to write off for a good while yet. Meanwhile despite works well when it works, the laptop is a right royal pain to use when the dock is therefore unnecessary.

  What to tell boyfriend
  Is a really nice laptop Tecra M10 and Portégé series and series Tecra laptop computers Bussines there.

  But it seems that the DVI port on the Port Replicator Port Express is supported only on computers with ATI graphics card or nVidia.

  I found this Toshiba document:
  http://APS2.toshiba-tro.de/KB0/TSB7B0201000CR01.htm

  It s on Tecra A9 but maybe that it s a Tecra M10-related too

• Tecra M5 - crashes when you use the docking station - fan at full power but no start the thread

  Hi all

  As I say, I have intermittent problems where the machine crashes when you use the docking station. Sometimes at the beginning of the startup of windows then stalls and powers of fan at full power. If I take off the base of the machine, it works fine.

  I bought this machine because I had one in my previous job and he had found great. However, my only previous also had this problem sometimes when lashing...

  Any assistance received very warmly.

  Thank you!

  Hello

  Stand by. You have noticed this behavior when the laptop is OFF, connect to the docking station and after doing this you turn. Am wrong me or have I misunderstood something?

  Maybe's external screen connected to the docking station?