Tecra 8000: PC Wireless Card is not recognized

Similar Questions

• SatPro A10 - wireless network card is not recognized

  I recently bought a wifi minipci card for my A10. After installing the card I have powerd up and the card was not recognized by windows, which is nothing to add material etc.
  I am running XP Home Edition with service pack 1, and I don't think that the machine is ready wireless.

  Salvation will be

  According to the specification of the A10 SP is WLAN ready. Did you find a WiFi (black and white) antenna cable near the card slot?

  Please check device manager if there is an unknown device, as well as the entries under network adapters.

• Satellite L300-17N (PSLBCE) - wireless card does not work

  Hello

  I recently bought a Toshiba Satellite L300 (PSLBCE) that came without any operating system and the dirvers. I installed WXP PRO SP2 above and downloaded all the drivers from the Toshiba site. Everything has been installed ok and functional except for the WLAN card. The wireless network card, it is a Realtek RTL8187B but it is not recognized by my laptop: if I Check Device Manager it does not appear (it does appear that "Network controller" with yellow mark). Then I went to Realtek website and download new drivers from there and installed again... also with these dirvers WLAN card still not recognized.

  No idea this coud be the problem? I don't know that I have downloaded the correct dirvers from Toshiba Web site as well as the Realtek site... but none of them helped. The chipset drivers have also been installed and also the last BIOS version (my BIOS version is newer than the one on the site of toshiba with the drivers for this model)
  May this be a conflict with the other dirvers or WXP PRO SP2?

  Thank you

  Hey Buddy

  Satellite L300-17N does not support Realtek RTL8187B but Intel 11 a/b/g (13ch) - Golan Wlan card.

  I recommend to visit the portal of Toshiba Europe WLan and recommend to download and install the driver Intel WLan from here:
  http://APS2.toshiba-tro.de/WLAN/?page=downloads

  Here, you can try the Intel PRO/Wireless 3945/4965/5100/5300 driver package!

  I would appreciate your comments

• Equium A60 - 173: A the wireless card or not?

  I wana to know either my laptop (EA60-173)
  has the wireless card or not. If so then I can set it up

  Hello

  Each unit with wireless card has a label of WiFi in the lower corner, and the card is also listed in Device Manager. Unfortunately I found the info Equium A60 isn't ready WiFi and only solution is the card PCMCIA WLAN or same USB.

  Good bye

• Used the update and now the video card is not recognized

  I updated updater manual update and have not updated anything since early December, 01/30/10 I installed the 5 important updates that were listed, I don't remember who they were, after installing the computer needed to restart and after the recovery, the video card is no longer recognized.  I get the BIOS beep code for no video card or bad video memory.  I know that this seems to be a hardware problem, but this computer worked fine until these updates. Now that the video card is not recognized, I can't even get into the BIOS, and still less actually starting windows. Any help/ideas what caused this and how can I fix this are greatly appreciated, thank you very much. Even a list of the latest important updates might be useful, I can't seem to find a list of anywhere.
   
  System-Vista Home Premium 64-bit
  Palit-card nVidia GeForce 9600 GT graphics card

  Oh and I took out that graphic card and put in a different one, nVidia PNY GeForce 7900 GS and always get the same error code. I also disconnected and removed the battery from the motherboard to reset the BIOS, still the same problem.

  Hi JohnyDick,

  This problem seems to be due to the updates of Windows, although it could be a coincidence.
  I first you recommend to remove the nVIDIA graphic card and connect the monitor to the onboard graphics card, then try to start the computer.
   
  If the problem persists then I recommend you to contact the computer manufacturer for assistance.

  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• HP 15-r240tx: wireless card driver not install (missing)?

  Hello world

  Recently I bought HP 15 - r240tx (FREE DOS) from Flipkart, I installed windows pro 8.1 as soon as I received the laptop.

  I downloaded all the drivers from the HP driver page and installed most of them.

  My nvidea, audio, display, usb etc drivers work fine but my Wireless card is not.

  I tried the realtek driver, but it is said that the network cable is not connected.

  "" On the help desk, it gives the same error: "connect a cable Ethernet in this computer"

  Also the button on the wireless keyboard is always on (white) and never goes.

  I'm confused, am I missing a driver or something? Can I still a wireless adapter?

  I would be happy to provide more information...

  Thank you.

  Hi @Gauravdeep .

  Thank you for your response.

  Your network card should not be listed in the other category.

  I suggest that you remove the network device and unknown in the other category.

  Then search for the hardware changes.  This should then list the network under network adapter.

  Once this has been accomplished, ran the HP Support Assistant to find the drivers for your network card.

  Good luck!

• PC with wireless card will not connect to the login of the user (Windows 7 RC)

  My PC uses a Rosewill (RNX-G300EX) wireless card with the software and drivers of Railink.

  With Windows XP (Pro) PC would connect to my home network and the internet on startup without user logon.  It is important to me because the data that I want to use on the network on this PC, and I don't necessarily want to have a user logged on to do.  I also have immediate internet access to connect remotely with TeamViewer, which worked perfectly with Windows XP.

  Since my switch to Windows 7 RC, I don't get the immediate connection through the wireless card.  It does not connect to the local network or the internet until a user logs on.

  Articles I checked:
  Driver - Microsoft actually already provided an updated driver that were obtained through Windows Update.  The driver for the wireless card should not be a problem.
  Power settings - I checked in advance for the power settings in Windows 7 and made sure that the wireless card has been set 'Maximum Performance '.
  Properties of the device - I have checked the device properties for the wireless card and made sure they were NOT defined to allow the OS to turn it off to save energy.

  I missed some type of parameter which is a novelty for Win7?  My computer with a wired network connection works fine with Win7 and is accessible at startup without user logon.

  First of all, thank you for the Mark test.  But the problem was not to have the connection when a browser is opened.  To open a browser, a user needed to be connected... with a logged-in user, the wireless adapter worked fine.

  Now, to answer my own question for someone else who might read this.

  I sent this message to Rosewill.  They advise that Ralink (spelled correctly this time) had not yet developed a good driver for Windows 7.  Windows Update apparently used a Vista driver and Windows 7 is apparently a bit different... or just Ralink is not cut with Vista either.

  So, I tried a Netgear USB wireless adapter.  BINGO!  The computer automatically start this device.  There is now a network connection to start.  TeamViewer now shows the computer as being online without that person may be connected.

  ANSWER: hardware
  RALink is a failure by juggling the time.  If you are looking to buy an adapter wireless network with a Ralink chipset, don't.  The link that Rosewill support sent me for the Ralink drivers was broken.  The Ralink site shows it as having certificate problems and IE8 does not recommend open it.  They are apparently dropping the ball.

  I'll buy a new wireless network adapter.

• Pavilion dv6449us wireless card is not not recognzied

  I have a Pavilion dv6449us which Broadcom wireless adapter is not recognized. I replaced it with another, and it is still not recognized. The light on the switch that allows me to turn off the wireless service is orange. There is orange if I turn it on or off.

  I am running Vista 32-bit SP2.

  Should I assume it's a hardware problem on the motherboard? Any suggestions will be appreciated.

  Thank you very much for the research.

  Hello

  I should have read your original thread more closely.

  happydog89 wrote:

  I have a Pavilion dv6449us which Broadcom wireless adapter is not recognized. I replaced it with another, and it is still not recognized. The light on the switch that allows me to turn off the wireless service is orange. There is orange if I turn it on or off.

  I am running Vista 32-bit SP2.

  Should I assume it's a hardware problem on the motherboard? Any suggestions will be appreciated.

  Thank you very much for the research.

  You replace it with an identical module?

  I didn't know you were already inside the laptop. Are you sure that you have reconnected the antennas?

  Here is a link to a long thread seriously on the problem with the dv6000 series laptops wireless.  When they are under warranty, HP replaced the modules wireless with a newer version.

  Best regards

  ERICO

• Satellite Pro 4600 Wireless card does not work with WIN2K?

  I have a Satellite Pro 4600 with UK dealer PA3070U-1MPC wireless operating with Windows 2000 card

  The wireless client Manager detects the network from my wireless router and the signal is excellent and I see all the Green swhowing bars.

  But I can't mske a connection in 'connections' wireless says "network cable is disconnected.

  the router works well with other laptops in my house.

  I have the latest version of Win2K also downloaded and installed the latest versions of client manager and WLAN driver for win2k to the toshiba Web site.

  'Support of toshiba in Turkey' told me ' I need another driver for Win2K for my driver wireless card cause win2K on the toshiba site isn't for "thie" wireless card ". I have been waiting for this for 3 weeks now and couldn't join the UK level 3 elusive support who supposed to have this driver. I saw on the internet is the same wireless card was sold as an accessory "made by toshiba" and he said that it is compatible with Wim2K

  What I then please? It works with Win2K, is it "another driver" and so on?

  Thank you

  Hello

  I don t think that there is something wrong with the driver because you can receive signals from router (green bars). If the driver WLan would be a mistake if wouldn t receive all signals.
  Please check device manager. If the wireless card is recognized if you are using the correct driver and the driver has been installed correctly.
  Please see this page:
  http://209.167.114.38/support/TechSupport/TSBs/all/-TSB000705.htm

  In my view, the message "network cable is disconnected" appears because your (NOT wireless) LAN cable is not connected. This post has nothing to do with the question of Wlan.
  You should check your WLan settings again.

• HP dv6815nr: Wireless Card will not connect to internet

  Hey people, trying to make my old laptop back to semi in working order.  Did a fresh install of Vista, but the wireless card for some reason any will not access the internet, says "local use." Internet works as the other computers in the House are connected on the wireless and when I connect the ethernet, features of connectivity cord.  Crossed and uninstalled/reinstalled the driver.  I have no special security here, just the windows firewall, which I disabled the thought that he could block, but it was not the question.  Other ideas you can come up with that would be great.  I have also included the hardware ID for my wireless card.  Pilots have been taken off this site from hp for my computer model as well.

  PCI\VEN_168C & DEV_001C & SUBSYS_137A103C & REV_01

  Hello:

  You need to install a driver update... the problem is probably your router is too new for the old driver wireless deal.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-108905-1 & CC = US & DLC = in & LC = on & JumpID = reg_r1002_usen_c-001_title_r0004

  Go back and activate your firewall if you have not already done so.

• Satellite P20-604 - how do I know if it has a wireless card or not?

  I have a P20-604, which I think was not preinstalled with a wireless card. Just to make sure that my details are:

  Model No.: PSP20E-0Du43-G3
  Serial No.: 14735613G

  If she does not have a wireless card, how do I determine what parts to buy so I can set up a wireless connection?

  Thank you.
  Seem

  Hello

  As far as I know that the wireless card is optional on this unit. This means you have the opportunity to upgrade the unit with the wireless Mini-PCI card. At the bottom of the unit, you will find a machine slot for this card.

  Please visit this site to check what wireless card is compatible with your device:
  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/options_and_accessories_search_by_model.jsp?

  Good bye

• Portege R500 - Bluetooth PC card mouse not recognized

  I am trying to use a mouse with my R500 bluetooth PC card, but it is not recognized when I insert it in the PCMCIA slot.

  The light. I need to change any settings?

  Hello

  Usually, the PCMCIA card should be recognized directly after that it was inserted in the slot.
  There is no special driver for the PCMCIA. It s a BIOS according to the function.

  What you could do is to change the device configuration option in the BIOS.
  I think that it s on the second page in the BIOS.
  It s set configuration by OS. I recommend that you change this.

• Tecra S3 on Linux: hard drive not recognized

  Hello

  I recently bought a laptop Toshiba Tecra S3 and I'm happy with it, except for one important thing: I can not install Linux on it.

  I tried with the latest versions of Fedora Core and Ubuntu, the hard drive seems to be detected, but it is not recognized at the time of installation. I guess it's a matter of (too) new chipset Serial ATA.

  You have any recommendations or do you intend to contribute to the kernel modules in Linux/order that this model could be installed on Linux?

  Also note that I remember that I had the same problem when I tried to install Windows XP from a CD (not the recovery cd): the hard drive has not been detected and the installation failed.

  Thanks in advance.

  Hello

  I can t believe that you can not install a Windows operating system.
  You formatait once again the HARD drive? I recommend to format the HARD drive completely, then install the operating system.
  In addition, if you want to use the Windows operating system, you must use the recovery CD because this image included all the necessary drivers.

  If you want to work with the Linux operating system, I recommend using the Knoppix distribution. In this case you n t need to install anything. This Linux you can start from the DVD or CD and it works as a Linux operating system normally

  Good bye

• Satellite 1905-S303 PCI Wireless card does not start code 10

  I put a PCI BCM94306PM broadcom wireless card in my laptop. The laptop is equipped with led however one is damaged and can not be connected, these cards may work with only one side and I even read somewhere that they can work on a short range with no led. My problem is the Device Manager indicates that the device cannot start code 10. I have a fresh install of XP Pro SP1 (not from the original restore disk). With this in mind, I think there must be some Toshiba utility or the missing driver to allow the map to work. Any help appreciated.

  Hello

  Code 10 means that it is not present, not working not properly, or does not have all the drivers installed.
  In this case you need to download the latest driver on Toshiba website and install it.

  Best regards

• SD memory cards are not recognized on satellite A200

  Hello!

  I had a Satellite A200 installed with Vista.
  When I insert the SD card into the laptop, nothing happens. My SD card does not seem to be recognized by the system.
  I tried to different maps, but none of them have been recognized.
  SD host controller is listed correctly in the Device Manager.
  I don't know what happened, but there is no problem with SD cards before you recognize.

  Thanks in advance!

  Hi there, my suggestion would be first uninstall and then reinstall the drivers from your SD controller (available for your laptop model on your regional site of Toshiba drivers). If this does not resolve the problem, then visit the following link to download an update to enable playback of higher capacity SD cards under Windows Vista: http://www.microsoft.com/downloads/details.aspx?FamilyID=e42fc131-6a76-4b27-934a-fb19dd323dab&DisplayLang=en if this fails, then make sure that you are upgraded to Service Pack 1 of Windows Vista.

  I hope this helps