Tecra 8100 did poster need nothing on LCD - LCD cable

Similar Questions

• Equium U400/146 - I need a replacement lcd cable/Ribbon

  Hello
  Please help I have searched for days.
  I need a replacement lcd cable/Ribbon. Identification number (DDOBU2LC000)

  My laptop is Toshiba Equium U400/146 PSU42E-00400SKS model number. Sound off out of warranty, so I took it to
  my local repair shop, but they could not get the part. The problem with the LCD is that it starts in green
  I can still use the programs, the grays and whites shine through.

  When it is connected to a crt monitor, the laptop is fine. Return to the cable, the screen number is REC-NI3311-LOL. C1

  If someone could point me in the right direction for this part, I would be most gratefull

  Thank you

  Hello

  All laptop parts can be ordered from the local ASP (certified partner).
  I think that guys should be able to order this cable/Ribbon.

  Here you can find the database with all FSA worldwide:
  http://EU.computers.Toshiba-Europe.com-> supported downloads &-> find an authorized service provider

  Good luck

• Tecra 8100 - lack of tv out cable

  Hello.

  I recently bought a laptop Tecra 8100. There is unfortunately no tv output cable included.
  According to the manual (ie. here: http://www.microdom.by/olddata/pdfspec/tecra_8100.pdf) the tv out port provides a signal s-video (NTSC/PAL) 3, 5 mm mini-jack port.
  The missing cable must be a RCA conversion cable.
  Is someone can you please tell me if there are special requirements that this cable must meet to the? It is not difficult to get a mini-plug cable 2xRCA audio conversion, but of course, it does not transmit the video signal.

  Clues?

  I'm working on Win XP SP2, the installed graphics card is S3 Savage/MX.

  Thanks in advance for advice.

  Hi mate,

  I know cable companies; It s a rare accessory of the Tecra 8100. The problem is, that the Mini-Jack 3.5 "has it s own format, so it will fit only in 1 x 3.5" to 1 x RCA.

  These cables are either on Ebay, or contact you an ASP (certified partner) which could probably send you such cable for little money from low...

  Here´s a link (if you need) to find the nearest ASP in your country:

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT

  Good luck man

• Need driver Ethernet for Tecra 8100

  I need a driver ether c16 ether c16 for Tecra 8100

  Hello

  All the drivers that are released by Toshiba are on the European driver Toshiba-> archive page

  http://EU.computers.Toshiba-Europe.com-> support download &-> download drivers

  I m not sure what driver do you need exactly, but all Toshiba drivers are located on the driver page.

• Need driver graphics card for Tecra 8100

  I have a Tecra 8100 810-1With Win98 series.

  I format the HARD drive and installed Win2000pro but some drivers not found on CD as graphics card, sound card and Ethernet card.

  After my laptop have only the 16colors and the small window that opens.

  I upgraded W2000pro by Microsoft Update for IE7, and service pack 4.

  Other readers to another device, I founded, I installed them and they work well.
  Only for the graphics of the very hard to find map drive for S3 savage/IX w/MV.
  I find 79036agplogo_S3.zip

  I tried to install it, the installation is OK.
  But when I started PC I have an error message in French, I translate it:
  "The pilot \Systemroot\system32\drivers\s3gsavm not found the point to enter the VideoPortSetEvent on the VIDEOPRT.sys drive.

  I tried to download it, but never found the driver for the graphics card, this is the link [http://fr.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=FR]

  Perhaps the drive on which I founded are not good? Where can I find it? Can you give me the link please correct?

  Thanks for help.

  Follow the link you have posted.
  Choose the category "Archive". Here you will find all Tecra 8100 drivers for windows 98 and Windows 2000.

• Looking for info on cable LCD of Tecra 8100

  Hello

  I have to buy a cable for my Toshiba Tecra 8100 LCD screen 13.3 "LCD size. I'm trying to find one on E - bay. Many people announce the cable for sale, but for 14 "Sceen. My question is: doesn't the cable LCD 13.3 "and 14" is unique and different?

  Thank you Arya

  Hello Arya

  It's the right question to the Toshiba repair center (certified partner). You will be very happy if someone here can give you the right answer. Before you wait here try to call the service partner and I hope they can help you. The addresses that you will find under http://www.csd.toshiba.com/cgi-bin/tais/su/su_gaspLocator.jsp?pf=true

• Need a display driver (s3) for Tecra 8100

  I installed Windows XP pro on my tecra 8100 and cannot get a full screen.
  Someone knows what's the problem? Do I need a new display driver voor the S3 Savage MX, or is it something else?

  Hello

  check in the Bios if the "Fullscreen/Widescreen" setting is enabled.

  Best regards

  Ben

• Need of SDRAM for my Tecra 8100

  Hello everyone.

  I would like to buy a souvenir for my Toshiba Tecra 8100
  It is and must be SDRAM 256 MB PC100 144pin - may by already used but functional

  It is too difficult to buy in my country
  I can pay for it about 20 euros

  Thank you

  Already find you on sites like Ebay or Amazon?
  Several months ago I ve bought a 512 MB RAM PC100 because my old module is dead.

  I ve found some modules of second hand on eBay but I ve decided to buy a new Amazon module

  Good bye

• Tecra 8100: Need exact specifications

  Can someone provide me with the exact specifications for the Tecra 8100 model. PT810E-02152-EN?

  Hello

  I don't know what you want to know exactly, but I found this site with detailed m laptop specifications.
  Please visit this site:
  http://www.DealTime.co.UK/xPF-Toshiba_Tecra_8100_PT810E_02152_EN

  Good bye

• Tecra 8100 - exchange of motherboard

  Hi all.

  Sorry, my English is not very good, but I need help. My Tecra 8100 does not only turn on the leds of power, battery and drive hard, but does not (Nothing on the screen).
  I need to replace my motherboard and it is B36084962019-a (Tecra 8100 model PT810E-01152-IT) but I think only B36086672015-A motherboard.

  Can I use these model instead of my?
  Thanks in advance to all.

  Hi tibi_1,

  Your English is ok and train me it s understandable so don t you worry about this and welcome to the forum :)

  About your problem, I can t give an exact answer, but a Council: contact an authorized service provider. I think that in this case you need 100% sure answer and you can get it from professional people only because it s a user to user forum where you can talk with normal people like you and me.

  Then get in touch with the guys, they will help you and if you are not familiar with laptop disassembly, they can help you to swap the motherboard.

  Good luck! ;)

• Install W2K on Tecra 8100

  Hi all

  I am trying to install W2K on a Tecra 8100, but I think I'm doing something wrong, because it keeps failing.

  If I just insert the CD it starts to start a load several files at a time when the Setup starts Windows 2000 (present at the bottom of the screen) and the installation crashes with a blue screen and the c0000221 error material unknown error \systemRoot\System32\ntdll.dll
  I read that, during installation, you will need to press F5 (in the screen where you can load a SCSI or raid driver) and then choose Advanced Configuration and Power Interface (ACPI) PC, but after doing this I get the same error.
  I have no additional material attached, it's original configuration.

  Any thoughts on how to solve this problem and get W2K on my laptop?

  Hello

  I think that this question has nothing to do with the Advanced Configuration and Power Interface (ACPI) or similar.

  I read about the error systemRoot\System32\ntdll.dll message, and there is no particular reason for this error.
  Sometimes some service packs missing cause this problem and sometimes hardware malfunction (RAM or HARD drive) could be responsible for a BSOD.

  You are able to install Win XP?

• Tecra 8100: Advice replace please - audio card?

  My 8100 Tecra faithful and beloved which is ideal for my purposes locked up the other day, in the middle of a session.

  Restart windows resulted in blocking machine once Windows is running.
  I started in safe mode - no problem.
  I have disabled all devices useless and then through a process of elimination of selectively allowing devices and reboot.
  I found that the problem was the Yamaha audio device - that turn on the machine and it would lock up, disable that and he would normally go.
  It worked fine now for a day with the disabled Yamaha audio device.
  I tried to uninstall/reinstall the device - no change.
  I even did a fresh install of XP - no change.

  I ran XP pro for over a year without problem (so far) and I consider not audio as criticism - just a nice to have.

  My questions are:

  Is there anything else I need to do in the way of diagnosis?

  Tips for common problems?

  Can anyone with experience of fixing these machines or similar notice if replacement of all of the audio card is likely to make a repair?

  I seem to remember the last time that I opened it about two years ago to change the processor that the audio Assembly was on a separate panel but is that all?

  Note that this is a _ancient_ machine and _not_ going to be taken to a repair shop where the Bill would be more that it is worth! I am competent to replace the sound card, more than that and I will probably continue to run without audio - I don't think that it worth replacing the motherboard just for audio...

  Thank you very much in advance for any constructive suggestion.

  Well, as you know these replacements are very delicate
  However, I don t think you will be able to replace this sound card but it s my personal opinion.

  From my experience, I know that the card (audio driver) his Yamaha is not fully compatible with Win XP SP1 and SP2. Update the audio driver is necessary.

  Google for it

  I searched a bit for some instructions how to remove these boards and found this page.

  There you should find a link to the page how to disassemble the Tecra 8100.
  http://repair4laptop.org/disassembly_toshiba.html

  Greetings

• Tecra 8100 hangs after startup

  Hello
  My Tecra 8100 has the same problem as described some time ago: the memory locations of MB were broken and doesn't have a connection properly. Even when I put paper or anything else between the cover and the memory module, it did not work and often my laptop has not yet started.

  I bought the new MB and now the laptop still start (I can see BIOS etc.) BUT crashes after Windows XP logo with notice: windows cannot start because the pci.sys file is damaged... The names of 'corrupt' are different, not only from pci.sys.

  When I portable computer boot from CD Win (to save the system) it blocks (crashes after 2-3 minutes). I tried to boot from Ultimate Boot Cd to detect the problem, but I can't do anything - always crashes after a short period of time - never start to run tests or Tools CD.

  I think that there is a problem of memory - I have 2 modules Kingston KTT-SO100/256, I tried to place them in different locations, together and alone, but nothing changes.
  These modules have worked with my old MB all the time.

  Any ideas?
  Radek

  I read on other forums that this error can appear if the modules of memory are corrupt or not compatible or the memory on the motherboard slot is faulty.

  Well, you have replaced the Board but do you use 100% identical to that of first?
  Perhaps modules of memory are not compatible with the new Board of Directors.

  "I found this Microsoft document that describes the Pci.sys is missing or corrupt" Error Message:
  http://support.Microsoft.com/default.aspx?scid=kb;en-us;319136&FR=1&PA=1&SD=HSCH

• Tecra 8100: vertical stripes on the screen

  I just bought a second hand Tecra 8100, who has been stripped of all its programs, OS. So I installed Windows98SE on this - now I get a screen with vertical stripes, which perch in the middle of the screen of the laptop with Windows just about visible in the background.

  I went to the display driver Toshiba and downloaded Web pages relevant windows 98se. Once on my laptop, the exe file does nothing; is neither their "graphics card" option in my device manager - everyone has ideas as to what is happening?

  Hello

  Please connect external monitor to your laptop and check if the result is the same. If so, there is probably a problem with the graphics card. If this isn't the case, I presume your laptop LCD screen is defective.

• Tecra 8100: memory slot problems

  I have a model tecra 8100 not: PT810L 12 c 42.

  I had problem with slot B mem, so collapsed to use it. Then I upgraded my RAM and inserted a 128 Mb TOSHIBA THLY6416G1FG-80 RAM PC100-222-620 slot A and used for a month. Then he suddenly went dead one day and did not boot at all.

  I took it to the point of service, they found somehow it work by sticking a piece of paper btw Aries and the cover. I used another week with ram cover duck taped it. Same story, then dead in the middle of winXP, switched off and no boot again. It took to the same service point, they tried some other RAM chipsets that it refused to start.

  The interesting thing is; When they inserted a faulty RAM in slot A and non-use slot B we get the message "memory incompatible chipset" on the screen. With the RAM mentioned above in the slot B (problem as always) and the A we get nothing, just a blank screen, DVD slot starts green lit, but nothing.

  WHAT SHOULD I DO, PLS HELP

  What is the RAM causing problems? What must a chipset that is exactly compatible with the model no pls?
  Is it the two locations of memory A or B, their change could solve the problem?

  This is the machine he itself, must it be thrown away?

  ANY SUGGESTIONS PLEASE

  Hello

  I n know where you tried to upgrade the memory but as Lisa suggested this was not a serious technician. I changed and upgraded memory on multiple PCs, and you must use 100% compatible modules! You shouldn't t install the modules with a brute force or use strange things as a communication between the housing and the memory module.
  Possible slots are damage due to use this procedure. But I hope you're a lucky man and everything will work correctly.

  If you n t know which modules are right and taken in charge so you should contact the service partner authorized Toshiba for the right and the upgrade modules.

  Good luck