Tecra 8100: Display of W2k driver - S3TRAY. EXE cannot be opened

Hello

I have the same problem as the BUSSINIT user posted earlier:
I have a Tecra 8100 but my screen resolution is only 16 colors, so I tried all the downloads on this page display driver, but:

S3TRAY. EXE cannot be opened, nothing to do.
This is the default or something.

The driver is probably old or something, but what to do?
I mean, I can't work with display only 16 colors, please help me.

THX

Hello

On the Toshiba page are two different Wk2 drivers listed:

5.12.01.7002 - 7.30.2 pilot S3 display for the wild graphics card

7.40.29 display driver for the S3 Savage MX

Check if you are using the correct driver!

Tags: Toshiba

Similar Questions

  • Tecra 8100: display suddenly will Dim

    Hello

    during normal operation of the Tecra 8100, suddenly the screen darkens. The display still works, only the backlight is dark. By pressing the small pin, which is turn off the backlight when you close the screen, light reappeares. Sometimes for hours, sometimes for a few minutes, but especially the second. A restart of the computer solves the problem for at least half an hour. What can I do?

    Thanks in advance

    Kai

    Hello

    When the screen will Dim can you get by pressing any key on the keyboard or move the mouse?

  • Tecra 8100 - more large hard drive

    Hi, I have finally made it to the age of the computer and want to know if there is a bigger hard disk for Tecra 8100 and if yes what is it and is it personally difficult to install?

    Hello

    My opinion is that if you don t have enough experience with this stuff, it will be preferable to doing nothing on your own. I can tell you that HDD is placed behind the cover pack HARD drive at the front side of your laptop.

    What is a current capacity of the HARD drive?

  • Need a display driver (s3) for Tecra 8100

    I installed Windows XP pro on my tecra 8100 and cannot get a full screen.
    Someone knows what's the problem? Do I need a new display driver voor the S3 Savage MX, or is it something else?

    Hello

    check in the Bios if the "Fullscreen/Widescreen" setting is enabled.

    Best regards

    Ben

  • Tecra 8100: bios update of cd. exe does not command line

    I want to update the bios of my Tecra 8100.
    I downloaded the bios, but the pc has no floppy, I cooked up a cd bootable like this

    When I start the pc, F2, press c to boot from the CD-ROM, I get in a dos environment. I went to the drive Z, "dir" and see the bios.exe that I've burned to cd. To run it I type bios.exe and continue to be 'command unrecognized file name' when I type dir *.exe, he does not see the file either.

    Maybe I forget something here?

    + The message was edited by: removed link - bad info +.

    Hello

    Your described method does not apply to Toshiba laptops.
    Each computer laptop manufacturers supports various BIOS update procedures

    Toshiba on this page we:
    http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/downloadDetail.jsp?soID=356848&PF=true
    Here you can download the latest version of the BIOS for Tecra 8100

    The 4810.25 package must be unpacked everything first.
    Then you should check the files available.
    There is a readme.txt file that describes how to update BIOS using the ISO to CD.

    I hope I could help

  • Install W2K on Tecra 8100

    Hi all

    I am trying to install W2K on a Tecra 8100, but I think I'm doing something wrong, because it keeps failing.

    If I just insert the CD it starts to start a load several files at a time when the Setup starts Windows 2000 (present at the bottom of the screen) and the installation crashes with a blue screen and the c0000221 error material unknown error \systemRoot\System32\ntdll.dll
    I read that, during installation, you will need to press F5 (in the screen where you can load a SCSI or raid driver) and then choose Advanced Configuration and Power Interface (ACPI) PC, but after doing this I get the same error.
    I have no additional material attached, it's original configuration.

    Any thoughts on how to solve this problem and get W2K on my laptop?

    Hello

    I think that this question has nothing to do with the Advanced Configuration and Power Interface (ACPI) or similar.

    I read about the error systemRoot\System32\ntdll.dll message, and there is no particular reason for this error.
    Sometimes some service packs missing cause this problem and sometimes hardware malfunction (RAM or HARD drive) could be responsible for a BSOD.

    You are able to install Win XP?

  • Tecra 8100: Video-playing DVDs only with jerking / glisten under W2K

    I can't play a normal DVD on my Tecra 8100 (P3 600 MHz, 256 MB RAM, Windows 2000 with SP4)
    without convulsions. Already have try to copy the image of the DVD on the HARD drive and play directly from the
    HDD - same result. Therefore, it is NOT a problem with the DVD drive, may be a problem
    with the S3 S3 Savage/MX VGA-Cardinal display driver integrated V installed 5.12.1.7002.
    Tested with PowerDVD 6 and VLC media player. Any special DVD playback software for the
    8100 available? Please help, try several hours to solve this problem, already
    talk with toshiba customer service!

    Hello

    Well, the Tecra 8100 is not a high-performance notebook and maybe it is not generally possible to watch DVDs jerking-free s.

    But I think you should check several parameters before we abandon ;)
    In order to check if DMA and not PIO mode is available and updated on the IDE controllers.

    Check if you have installed the latest version of DirectX.
    You said that you are using the latest version of the graphics driver. Well perhaps you will check this site:
    http://www.S3graphics.com/en/resources/drivers/legacy/software_archive.jsp#id_290298drv

    Also check if the installation of some codex will help you:
    http://www.DivX-Digest.com/software/nimo_pack.html

    The Nimo Codec Pack is a nice collection

  • You cannot change the color display on Tecra 8100

    I have a 8100 TECRA with Windows 2000 Professional installed. I tried to install "Streets and Trips" and it won't work without colorful. I can't change the view setting because it doesn't have this option (high resolution). Is there a driver available to fix this problem?

    Don

    I found on the Toshiba page two graphic drivers for W2k on the Tecra 8100.
    Just install the graphics driver and the option should be available

  • Tecra 8100, upgrading the BIOS, whitch that hard drive is taken in charge (40 GB)?

    Hallo,

    I have an old Tecra 8100 one I want to update BIOS. Who knows who is supported (20 GB, 40 GB) hard drive and where can I find the specifications?

    Thanks for your information.

    Georg

    Hello

    As I m wrong not the Tecra 8100 does support an IDE HDD controller.
    In this case, it should be possible to use the 2.5 IDE HDD.

    I can't say much about the formats supported, but the fact is that the size of HDD supported depends on the HARD disk controller. The old controllers IDE up to what the ATA - 5 (also called Ultra ATA/66 or Ultra DMA/66) supported LBA 28 bits, which allows you to use the 120 GB HARD drive max.

    Since ATA - 6 (also called Ultra DMA mode 5 or Ultra-ATA100), you can use IDE hard drives of more than 128GB.

    So if you want to, you can check your IDE HDD controller using a hardware diagnostic tool (IE Everest home edition). Then you might find out what IDE controller is and what drives are supported.

    See you soon

  • Tecra 8100 - upgrade RAM and HARD drive

    Hello
    I just got a Toshiba Tecra 8100. I do not have this small a HHD and I wanted to know what size I can get it up to. I know y thread already asked this same question, but the technology continues to go better then perhaps there are HHD I can get.

    I am also wanting to upgrade the RAM. I've seen places that sell 144pin PC100 512 MB and I was wondering if it is possible to upgrade this 2 of them or not.

    Any input would be great!
    Thank you
    Doug

    Hello!

    The Tecra 8100 was delivered with HARD s up to 20 GB drive. I'm pretty sure that this laptop has a limitation of LBA 28 bits ([www.48bitlba.com]).
    I put t know what HARD drive you have at the moment, but a hard HARD 40 GB or 60 GB would work in this good old classic.

    In addition, the Tecra 8100 can be upgraded to 512 MB of RAM. So that you can t upgrade your laptop to more RAM.

    Good bye

  • Need driver Ethernet for Tecra 8100

    I need a driver ether c16 ether c16 for Tecra 8100

    Hello

    All the drivers that are released by Toshiba are on the European driver Toshiba-> archive page

    http://EU.computers.Toshiba-Europe.com-> support download &-> download drivers

    I m not sure what driver do you need exactly, but all Toshiba drivers are located on the driver page.

  • Need driver graphics card for Tecra 8100

    I have a Tecra 8100 810-1With Win98 series.

    I format the HARD drive and installed Win2000pro but some drivers not found on CD as graphics card, sound card and Ethernet card.

    After my laptop have only the 16colors and the small window that opens.

    I upgraded W2000pro by Microsoft Update for IE7, and service pack 4.

    Other readers to another device, I founded, I installed them and they work well.
    Only for the graphics of the very hard to find map drive for S3 savage/IX w/MV.
    I find 79036agplogo_S3.zip

    I tried to install it, the installation is OK.
    But when I started PC I have an error message in French, I translate it:
    "The pilot \Systemroot\system32\drivers\s3gsavm not found the point to enter the VideoPortSetEvent on the VIDEOPRT.sys drive.

    I tried to download it, but never found the driver for the graphics card, this is the link [http://fr.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=FR]

    Perhaps the drive on which I founded are not good? Where can I find it? Can you give me the link please correct?

    Thanks for help.

    Follow the link you have posted.
    Choose the category "Archive". Here you will find all Tecra 8100 drivers for windows 98 and Windows 2000.

  • CD-ROM drive does not eject on Tecra 8100

    I have a Toshiba Tecra 8100 and my CD player will not eject. It only happens when it starts.
    Any ideas, everyone, how can I solve this problem?

    Even when I get it open habit run all disks?

    Hello

    You are not able to open the drive to be on the CD. Is this good?
    Generally, each player has a small hole to open the player manually. You can use a thin wire to open the player.
    But if the reader doesn t work correctly or t doesn't accept and recognize any CD so I guess the drive is dead and only replace the drive can solve it.

  • Tecra 8100: This HARD drive is supported for the upgrade?

    I want to improve the HD in a laptop Tecra 8100. However I can't find the HD player required to do this.

    Someone suggest where I can look?

    Hey Buddy, your notebook computer is an oldie.
    As far as I remember that the computer is about 6 years old.
    At that time, the supported laptop, 6GB, 8GB, 12GB, 15 GB, 18 GB, 20 GB HARD drive, and the disk 20 GB HARD is, in my view, a maximum size. More is not possible.

    I found kits of HARD drive you could use:
    PA3012U - 1 H 06 6 GB hard drive Kit II
    PA3027U - 1 H 12 12 GB hard drive Kit II
    PA3029U - 1:18 18 GB hard drive Kit II

  • How to change the display on Tecra 8100 drivers?

    I downloaded the driver for Tecra 8100 my girlfriend updates, but I can't figure out how to install them. The laptop is running Win2k sp4.

    I tried the 'normal' method of "update driver" and then selecting the new pilots, but Win2k still find the original drivers and not the new drivers.

    I also tried to unpack the new drivers in the folder that contains the original drivers and replace the files in duplicate. I zipped the original file so that Win2k couldn't see the original files. I then tried to run the Setup program, but the future restart the card was not detected. It is only when I unzipped the original files once again that the new map was suddenly, and v5 drivers have installed again!

    I really want to install drivers v7 - everyone has ideas on what goes wrong? can someone give me a step by step guide how to go V5 to v7?

    See you soon,.
    Dan.

    I forgot to mention - I tried to launch uninstaller to S3, but seems not to do anything.

    All advice appreciated!

Maybe you are looking for

  • Not able to install the file as in firefox

    I created my first addon and it works very well in dynamic mode (pointer record of profiles in the folder of development). Next, I created the file as to compress all content in the .zip and its replacement by as. I tried to install this. Firefox doe

  • Can I delete the second partition after recovery media creating?

    Hey,. I just create recovery media, with 2 DVDs and I wonder if I can now delete the partition on the HARD disk, which contains a folder named "HDDRecovery" called 'Data' I ask here because I don't want to do something stupid. Thanks in advance for t

  • January 1, 1970 my phone is now 'bricks' Will Apple difficulty / replace it!

    I was deceived by assigning the date of my phone January 1st, 1970 due to see post on twitter saying he would give me a new theme. Now that I Googled, I realize the gravity of the situation. My phone will not start, and it's because of a sort of loop

  • How to create a system restore point

    Hello. have a new laptop, and I would like to be able to create system restore points before as I have download things, when I go to the system restore, it asks only if I want to go to one and not how to create one.  Thank you.

  • I get the message Windows is set up PSSWCORE

    Hi, when I start my computer it keeps coming up with the message Windows is set up PSSWCORE and then after a few minutes it says that the information is on a CD-ROM disc.  I tried to put in my Windows Vista disk to see if that would take care of the