Tecra 8100: solid white vertical & screen turns off

Similar Questions

• Access code is lost as soon as the screen turns off

  When I turn my wrist after that my Apple Watch screen exploded, I need to enter the access code. I turn on the wrist, the screen turns off, I turn back, screen lights up, I need to re-enter the password. And so on and so forth. The watch does not maintain the code.

  I am white white, is not dense hairs on my wrist, no tattoos and I wear the watch very well on my skin.

  The funny thing is: it is a replacement watch, I got today. The other had the same problem, but this is probably because the bottom of the watch with the sensors fell, must have damaged the sensor cable. But this one is brand new.

  Hello

  Make sure the wrist detection is enabled:

  • On your iPhone, in the application of the watch, go to: My Watch (tab) > General > detection of wrist - turn on.

• Y560 screen turns off automatically

  Hi all

  My Y560 Ideapad screen turns off after 1 minute of inactivity.

  The parameters of current energy said it should do so after 5 minutes of inactivity. Any ideas?

  Figured it out. Turns out I have my screensaver set to 1 minute, and it was 'white '. Finally I remembered, I got "no screen saver". Maybe it has changed when I changed my desktop theme. (this is for Win 7)

• U2913WM screen turn off randomly

  So I got this monitor ultra wide nine of the store with 3 year warranty. I had these questions of the day 1. I came home to repair, but given that the problems occur at random I'm afraid that the retailer they come back to me it works normally after the test for 30 minutes.

  The questions are:

  1. the screen turns off (screen with backlight black still on) or it will freeze randomly. To resolve this issue, restart the controller using the power button, which in turn will not immediately respond, but will keep wait me for 6 to 10 seconds until the monitor turns off eventually. Monitor back to work normally after the restart until the next random freezing. Sometimes this happens when changing the resolution (for example launch a video game). This can happen as often as 5 - 10 times a day.

  2 monitor sometimes not into mode 'sleep' when the computer is off, put to sleep, or not used for a long time. Instead, the screen will turn white with the backlight, as in the previous edition, and the solution is the same - screen reboot. If this isn't the case, it will remain frozen, even if the computer is turned on or awakened.

  These produce both DP and DVI ports. My video card is Gigabyte GTX 670 2 GB. I don't have any of these problems with my previous screen using the same PC.

  I would appreciate a response to a Dell employee. Can it be fixed with a firmware update? The update can be done at home? I'm more or less a power user. If this isn't the case, I can get the monitor serviced by an authorized dealer (in Sofia, Bulgaria) with a cover letter or notification by email from Dell. Because as I said there is a good chance I will be denied a replacement of a work apparently monitor. Warranty service is not a strong point here, unfortunately.

  Can it be fixed with a firmware update?
  * Unknown. Try to test with DisplayPort 1.2 disabled on the OSD (On Screen Display)
  * Computer Gigabyte GTX 670 DP--> Dell DP to the CDM cable--> U2913WM CDM in
  * Support on the selection of input Source key
  * Put out Mini DisplayPort
  * Press and hold the green check mark for 8 seconds
  Disable the DisplayPort 1.2
  Out of the OSD

  The update can be done at home?
  * No. Pour get a monitor with the latest firmware, you must launch Dell monitor Exchange.

  If this isn't the case, I can get the monitor serviced by an authorized dealer (in Sofia, Bulgaria) with a cover letter or notification by email from Dell.
  * No. we do not repair the monitors on the ground, simply replace us them.

• Latitude D610 screen turns off after the Windows XP loading screen

  I'm having a problem with my Latitude D610 where after the Windows XP loading screen, the screen turns off completely. No BSOD, no login screen, just a white screen. This started happening at least a year, however, I bought a new computer if it is passed to the hatch. I tried the system restore when it appeared first without success. The computer starts in Mode safe. Any suggestions?

  If it starts in mode without failure, then its almost certainly a driver and with the blank screen problem, I suspect a display driver.

• Equium A200 - screen turns off

  Hi, I'm having a problem with my Toshiba laptop, the screen turns off randomly and the computer still seems to work, but when I use a VGA cable to connect to a TV it does not display anything.

  Here are pictures of when it fires
  http://Tinypic.com/r/vr9d7d/7 yellow on the disc tray is turned on
  http://Tinypic.com/r/2d9poya/7 that the front turned on lights and computer sounds like its operation.

  This led me to believe it's a hardware problem, but when I turn on the computer in Mode safe it never turns off. I also got the fixed ups this year because the screen was losing power.

  Can anyone help I can't really afford a new laptop at the moment

  Hi David,

  It's a little confusing, it doesn't always happen when you shut down the computer, or just sometimes?
  What do you do to get rid of this? Always remove the battery and the AC adapter or what exactly?

  I think that it s a hardware malfunction, usually has nothing to do with the software. What you can try is a BIOS update from the official website of Toshiba.

• Satellite A200 - screen turns off without reason

  I have a Satellite A200-E530D on Windows Vista Home Premium. For a month, I had something strange happening on my computer, shortly after the start, the screen turns off. without good reason! the only option I have is hard to system boot and everythings... Although a few times after the restart he still went.

  I tried to upgrade to the last poster of drivers (I have an Nvidia Geforce Graphics card 7300 Go with 128 MB of VRAM)

  Another weird thing, Vista SP1 does not install on my machine. tried to uninstall my Anti virus, but that did not help either one.

  Can anyone shed light on my dark screen?

  Hello!

  You have the same problem on an external monitor?
  I m not sure if it s a display problem, mother or software card

  Do you have what display driver installed? You have downloaded the driver from the Web from Toshiba site?
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Good bye

• Satellite A100 - 784 PSAANE - screen turns off automatically

  Hi friends,

  I have a Toshiba Satellite A100 - 784 PSAANE with windows visa Home Basic edition.
  Now for 15-20 days I am facing a strange problem. The screen of the laptop emits a sometimes (not necessarily every time) and then when the frequency increases the display turns off automatically!
  Then I must Hibernate or he put laptop to sleep to find again the screen... Seriously, I don't understand the problem.

  Please help me.
  Thanks in advance

  Hi Julie,.

  It sounds as if something is harming your graphics driver causing the display to turn off. If the problem occurs only when you use certain applications or only started after installing a new application you may need to restore your system to a restore point before new applications have been installed. As a test, you can try to start your system in safe mode and see if the problem persists.

  I also recommend that you re-install your graphics drivers to see if it improves the problem.

  Other possibilities are that your graphics chip is a failure or overheating causing this problem in which case you have to return your laptop to a Service approved for the additional diagnostic agent.

  My last thought is that you may have a problem with the inverter FL (the component that provides the lighting of your LCD screen). Check, when the screen turns off, if you can still see a residual image on the screen. If yes then the FL inverter is definitely at fault.

  Kind regards

• Screen turns off when working DC but Portege R500 unpluge

  Hi forum.

  Just bought laptop Portege R500 PPR50E-04x048en.
  When I start the PC (BIOS is set to default) when using battery everything works fine.
  When I unplug the power cord, the screen turns off. I plug it back, the screen is still off!

  Any ideas?
  FN + F5 works, but does not help.
  FN + F1 don't see it's something.

  Great!
  Thanks for the comments.

• Equium A20 fell and the screen turns off always

  Hi, I was using my satellite A20 long (4 years). Never had any problems. Recently he fell and the screen turns off always.

  I can see the toshiba logo and the windows logo also when starting, and even I can enter the BIOS and change the boot order too... but as soon as windows load screen is black. I don't understand

  Anyone with the solution?

  Thanks in advance...

  Hello

  > but as soon as windows load screen is black. I can t understand
  This means that the display output has accidentally changed to an external.

  Have you checked if something would be visible on the second external monitor?
  Select this check box.

  In addition I advise to use the FN + F5 keys to check if you can switch the output back to the internal display.

• Satellite A210 - 17L - screen turns off

  Hello people,

  I have a similar problem to [http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=61255&tstart=15], screen turns off by itself randomly, but backlight remains lit and laptop always seems to work (judging by fan). This started after upgrading Vista to Windows 7 (new installation), there was no problem before. I tried to update the display driver, first ATI Catalyst, then Toshiba official one, the customer pays less often, but still doesn't work, it's nice embarrassing ;) It occurs regardless if the laptop is used or just slowed down and is not caused by overheating or saving energy, also cell is generally connected with mounted battery.

  I have the last opportunity to go and update the BIOS, but I'm in fear of bricking the thing, so he would try as a last resort.

  Any idea guys?

  Thank you

  Hello

  There is an easy way to solve this problem: connect an external monitor and check what happens. If everything is ok on the external monitor installation (Windows) and internal monitor are ok, the problem must be internal monitor itself.

  If it s the monitor itself it s inverter FL, LCD cable or LCD itself. That s is not easy to say on this virtual path for your laptop needs to be checked to an authorized service provider. Guys can make an accurate diagnosis.

• Gigaframe L81 - after 2-3 seconds, the LCD screen turns off

  Hello!

  I think, I missconfigurated my camera... I put the automatic light (auto light) options, then the LCD is turned off. OK, its light of day here, but how can she Cook?

  And - perhaps because of the thing said? -its LCD screen turns off every time, when I push the power on button. I'm tired of using the reset switch, but she has - at least, in the LCD - no effect.

  Device is reset, then lights up the screen, I see him starting, I can touch control "buttons" on the right side (I can see the blue lights), but after only 2-3 seconds, the LCD display turns off again.

  Although I can do anything on my camera - attach PC files, copy or dele (ordered from Windows) etc. I just don't see anything in the LCD screen.

  What's wrong?

  If it still does not work after resetting it, then it may be a hardware problem.

  I think that you will need for repair/replacement.

• Satellite 1800 - 752S - the screen turns off

  Hello world.
  I have a satellite 1800 - 752S.
  Since an ew months ithas a weird problem: the screen turns off. If I press and release the button the lid on what it is, but after that turns off again quickly. OT goes off sometimes immediately, sometimes after a few minutes, or even hours. Sometimes it provides be when I run out of battery and bothers me on AC, sometimes against. It works fine, after I turn sleep or hibernation several times, and after a reboot, it bothers me. I've updated his BIOS for the lates on this site, which would not help. I guess it's a hardware problem, because it's the same problem under Linux, and I tried to install different versions of drivers and windows (not only the one of the recovery CD). Anyone have the same problem before. Any help will be appreciated.
  Thank you very much
  Roman

  Hello

  I think you're right, it's a hardware problem. But to be sure, try connecting an external monitor. If it works without problem while laptops, screen turns off, then it must be a hardware failure.

  I guess it's a problem with the FL inverter. You have to give your machine a service partner Toshiba for repair.

  Good bye

• Anyway continue Voiceover if the screen turns off?

  Hello world

  I use Voiceover to read eBooks for me, but the voice-over goes out once the auto lock turns off the display.

  Is it possible to do the Voiceover to continue even if the screen turns off?

  Thanks for your help!

  Hi Dionysus17,

  AFAIK the only way to solve this problem is to disable the auto-lock on your iPad. To do this, go to settings > General > lock and from here you can choose when you want to stay for before your locks iPad screen.

  Hope this helps,

  Aaron

• Screen turns off when the Satellite A45-S250 is moved in the direction of less

  Hello.

  I have a satellite A45-S250. I had no previous problem with this machine. However, when the computer is running too long, or it is moved in the slightest way the screen turns off. I don't even have to type very slowly - or I lose the screen.

  But also, as I have said - sometimes I won't even be near the computer and the screen turns off. When I lose the screen if the light shines on it - I can see, it's always VERY fair Sun. Generally, it will come if I use the FN + F5 button.

  I don't know if it is a screen problem or a connection problem. It occurs with increased frequency. Any suggestion would be appreciated.

  Thank you

  Mindylea1

  Hello

  From your description, I assume FL converter is defective and must be replaced. FL inverter is responsible for the background light and the typical symptom for faulty FL inverter is dimming or blinking display.