Tecra A11 - 17V unable to connect to the WLan
I have a Tecra A11 - 17V 15.6-inch and the problemis that i can´t get conection WiFi at home.
With all of the other devices I come in my WLAN and the Tecra also in others, but not in mine.
It is a WPA2-PSK AES and 128-bit encryption.
This may be the cause?
Best regards
The wifi connetion couldn't work for different reasons.
That is to say the Wlan standard could not be supported, or there might be a problem with the compatibility of encryption.
You can perform a simple check.
Disable the wireless encryption in your router settings and try to connect to the laptop to open Wlan (unsecured).
Of course, this should be done just for testing purposes and the Wlan must be always well attached.
Tags: Toshiba
Similar Questions
-
My ZTE open C unable to connect to the wlan with 63-signs-hex key.
Hello
my C open from ZTE unable to connect to the wlan with WPA2-PSK and a 63 sign hex key. When I create a 2. ESSID with WPA2-PSK a sentence normal, everything's fine.
Oliver
Hi OliverwithZTE,
I understand that you have connection problems to your network WPA2-PSK.
Unfortunately, WPA2-PSK is currently not supported on Firefox OS version 1.3. Only WPA-TKIP and WPA2-AES are supported.
-Ralph
-
Satellite A500 - 03P: unable to connect to the WLan using Win 7 + event message
Hi all
I recently bought the Satellite A500 with the offer included Windows7 while he was available late October 09.
So I had the Toshibe DVD for the upgrade and followed the steps and Visa home premium upgrade to Windows 7. Now I have two questions.
(1) I get a system event Notification after start, talk to me about the system event log. The full message is below.
Unable to connect to a windows service
Windows could not connect to the System Event Notification service. This problem prevents limited users to logon to the system. As an administrator, you can view the system event log to see why the service failed(2) I was able to use this laptop for the internet before the upgrade, both via a USB wireless drive as well to the office via a DSL modem.
Now I can't access the internet after the upgarde of Windows 7!For example the Optus dial-up box pop up appears commandeLorsque I click on 'connect', it does not connect.
Can anyone help please?
Thank you
C IHey Buddy,
(1) did you check the Configuration of the Service for this service? The Boot System Event Notification Service type must always be set to automatic. This service is absolutely necessary for Windows and shouldn't t be disabled or set to manual startup type.
Check it!(2) to be honest I never heard on the internet BEFORE, but normally, it should also be possible to access the Internet with Windows 7.
Make sure that the WLAN or LAN card is installed properly and check the TCP/IP settings. If you are missing some driver you can get on the page of Toshiba. -
Equium A200: Unable to connect to the Wlan - no IP address of the router
Dear readers
I have a laptop Equium A200 Toshiba.
I TI a year, a little more of it and it did work under Vista perfectly, no problem.First of a sudded 4 weeks ago my wife told me that she can no longer connect to the internet.
I thought that it was something less serious, until I couldn't solve the problem.The laptop is not receiving an IP address wireless or cable modem.
I type cmd and I get an IP starting with 169 in wireless and wireed cases.
I also tried to reset the NETWORK card, but it does not work.It's frustrating seriously because we don't change anything on the other machine, then let updates automatically, this is obviously some update that triggered connect to stop the local distribution of load and internet access now it shows only local access.
Appreciate any help out there on root causes.
So far not much dad worked. R/PaulcouHello
In your case, I would first check the settings of the router.
I put t know what settings of your router is compatible, but you should go thought the simple options (such as when the first router configuration) and should check if everything is set correctly.In addition, you should check the settings of WLan connection. In the properties of WLan connection, you would find the TCP/IP protocol. Check the properties of the TCP/IP Protocol and set all parameters (IP address, getaway, etc.) to get automatically.
If all of these settings are set correctly, then start the console (CMD) and use the command:
ipconfig / renewThis should refresh the IP address and in most cases, it helps.
Last but not least, you should check if you can update the WLan driver!
-
Satellite P300-19 q PSPCDE Win XP - unable to connect to the WLan
Hello
I just bought a P300 19 q PSPCDE laptop that I am running with win XP.
I have problems with the wifi connection.
Seems to be a common problem. I updated the driver for the Intel 5100 last, assured the wifi on the front switch is active, pressed Fn + F8 to make sure that the wireless card is enabled but I can't always see all the networks, even if my old computer display about 8 to reach wifi networks.The only solution I can find on the forums is to use an older version of BIOS. The BIOS of my laptop is indicated as v1.8 (13 August 08). However, when I check this site the latest version of the BIOS available for download is version 1.6, which is probably older.
So the question is - has anyone successfully solves the problem of connectivity using the BIOS 1.6 instead of 1.8 and if so how install you it because my computer refuses to use a BIOS older than the one already installed.
I'd be very grateful for any help before I tear in addition to my hair out trying to get the new laptop to work!
Liz
Hello. I had the same problem.
You have already done this, but
By fluke: under the control panel > Device Manager > network adapters, I saw one was "unknown device". Out of desperation and more hopeful than any other thing I've updated the driver on that, whatever it is and it turns out be a Realtek Wireless Adapter, after I had updated it.
Amazingly, everything worked OK after that,
But I don't see why he would never ship like that? And roll back a BIOS previous everything seems unfair...
See you soon
Bill -
Unable to connect to the WLAN router satellite P300
Hello everyone,
I hope you can help me with my problem.
I bought a Satellite P300. Now, I'll have some connection problems to my fritzboxfonwlan over a wlan network.
When I connect my laptop via a cable, all right. Only with wlan i´m problems.
My router ssid is displayed correctly. I can also type the key. But then the router is not to be found.I use as wpa2 encryption.
I think that Vista has problems with it. Vista has also the most recent updates and my wireless (intel agn5100) card.
I tried all the three drivers on the side of toshiba. I Don t know what I can do next.If you have any ideas, I'll be happy to hear it.
Hello
Have you checked if the address Mac filtering settings can affect the WLan functionality?
If the MAC address filtering enabled your WLan card mac address has been inserted, then your laptop wouldn't connect.Also I recommend you check the settings of the WLan card TCP/IP.
In the TCP/IP properties, you must set options for automaticallyPS: have you checked whether your P300 is the latest BIOS?
-
Satellite A500 - unable to connect to the WLan
I'd like someone to help me.
Have recently bought a satellite A500.
I'm new in the world of laptops so I'm wrong.
I connected to a router via a modem, the two netgear, the news.Had the two config for my network. Works well as long as ethernet is connected to the router of computer.
My wireless icon on the front of the laptop is orange.
If this should be green as the router?Pressing FN f8 it tell me wireless is connected.
When I remove the ethernet cable it tell me to fix the problem, I need to plug in the ethernet cable.
But I want to go wireless, I'm sure I'm missing something.Rang netgear but after that my router and it is not connected to wireless technology they could help me more.
I use windows7.Thanks to anyone who can help me.
> My wireless icon on the front of the laptop is orange.
> Should it be green as the router?The WLan led can only be ON or OFF. If the light comes on (any color) then it means that the Wlan switch is on!
It seems that the WiFi is enabled. In this case, you will need to properly configure the WiFi network.
You can use the own WLan settings in Windows or a Wlan configuration tool like Intel ProSet utility.First need choose the right SSID (wireless network name), right of encryption (WEP, WPA, etc.) and password encryption.
Please note that all of these parameters should be the same on the router WLan and WLan configuration software!Please check if the firewall does not affect the connection to the internet as well!
PS: make sure you use the latest version of the WLan driver
Here you can find the drivers:
http://APS2.toshiba-tro.de/WLAN/In addition, search and read comments here on the forum!
-
Satellite L505-144: unable to connect to the Wlan 802.11 N
Hello, I hope someone can help me with this
I've updated my old network wireless at home so I can stream media.
I replaced my old netgear G router and bought a netgear DGND3300 dual band N router to the hub and a WNDA3100.Office everything is set up ok on these as I can connect up to 300 kbps, which is good.
The current settings for the router are:
Up to 130Mbps at 5 GHz & 54Mbps 2.4 GHz"
channel 36 = N
Channel 11 = GAlthough the problem is the laptop.
Now, he says that the wireless laptop is N. When I connect to the router it connects only when G setting and I only have until 45 Kbps.Is there a way so that it can connect to BOTH channels to get the full speed or the wireless laptop is only a single tape device?
Thank you
SteveHello
Built into the laptop LAN card is a Realtek RTL8191SE 802.11bgn.
As you can see the wireless network card supports three WLan standards; 802 11 B, G and N.First of all, you must make sure that more recent Wlan driver is installed;
New WLan driver can be found here:
http://APS2.toshiba-tro.de/WLAN/In addition, you should check if 802.11 N standard has been chosen.
You should do this in the Device Manager-> card WLan-> properties-> Advanced tab.Welcome them
-
Satellite C665D is unable to connect to the WLan
Hello
My in-laws are staying with me and their C665D does not connect to our wifi network.
I can't turn on the wifi settings.I looked in to network adapters Device Manager and there is no present. I tried to add a new device through "manage wireless networks" and he says "Wireless is not currently enabled.
If I try to manually add a wireless network it comes up with 'windows wireless service does not work.
Look forward to some help on this one
The error "the windows wireless service does not work" indicates that the Wlan service has not been started.
Why? I don't know, but you can try to activate this service first.To manually start the wireless service, i.e. the WLAN AutoConfig service, perform the following steps:
1. connect to the computer as an administrator.
2. Click Start, type services.msc and press to enter.
3. Locate the autoconfiguration WLAN service, double-click to open its properties window.
4. on the general tab, change the startup type to automatic and click on the Start button.
5. click on apply, then ok.Then try to connect to the wireless connection and check the result.
-
Qosmio X 300-13 G - unable to connect to the WLan router using Project N
Hello
I purchased a Qosmio X 300-13 g (the only one available in Portugal :/) and I tried to connect it to a network wirelles N, but I always get an error message):
Windows could not connect because the defenitions of the router are different from your...Well you know why? I tried with several routers, and it is always the same...
TKS
Concerning
Is your WLan router supports 802.11 N draft standard?
Did you choose N draft standard on your WLan router?
-
Unable to connect to the WLan satellite E300
Hello
I also bought a new Toshiba e300 Satellite yesterday. I have the same problems and have updated to the latest firmware. What is complicated is, I have 3 other laptops (mac, more old toshiba & acer) and 3 iphones, they are all able to connect to my wireless network and it's only the new toshiba which cannot.
Other devices could see other local wireless in my neighborhood networks, while the new toshiba could see that my own wireless with only one bar of signal strength.
Looks like the Atheros device is the only issue. Your feedback is greatly appreciated.
>.. .updated to the latest firmware
Firmware? Which firmware?Maybe from other computers laptops don't use WLAN n standard and your new laptop computer for this. Who knows what standards to use all these wireless LANs. Try to check the WLAN settings on your router and your new Toshiba.
-
Equium L10-200 - unable to connect to the WLan router
I have a 200 L10
When I tried to connect WiFi my suburb does not connect with the router at all. Looks like it was trying to access the Internet.
Then window took to replace my IP address. But as I can not connect on it cannot be a substitute.How can I get them back.
Cable and work for laptop computer to my wife on the same router work ok.I am running XP and connect to the sky
Hey mate,
Why you can t replace your IP address?
First to connect properly, check if you need a static IP address or if you get an IP address from your router (DHCP).If you use encryption, make sure you typed the correct password. Disable filtering of MAC addresses in the router to connect properly.
Last but not least, make sure that you have installed the new firmware on your router.
-
Satellite L505-12 q - unable to connect to the Wlan on Draft N Router
Hello.
I have a Toshiba Satellite L505-12 q who that I connect to router Edimax br 6524n.
My problem is that when I connect to the router the laptop does not use n 802.11 g... The network card is Realtek RTL 8191se... He supports the project and it is configured to receive B G and N. When I set up the router to use only the band N the portable project sees the network, but when I try to conect it can not...
Can someone tell me where is the problem?
I updated the firmware on the router and adapter driver and still nothing good... :|Thank you.
Post edited by: Matt1990
Hello
First you need to update the WLan driver.
Here is a page with all the drivers:
http://APS2.toshiba-tro.de/WLAN/After that, go to Device Manager-> properties-> Advanced tab WLan card and check if the Draft N has been selected.
Restart the device and then try again
-
Equim L350 - unable to connect to the WLAN
I have a L350 Equim running Windows Vista Home Edition.
I was connected to my network wireless for a week with no problem and then more nothing.
My Atheros wireless network card can no longer recognize my network and it really baffles me.All my other devices connect to my network without any problem and the laptop can pick up just about everyone elses network except mine. . I'm reduced using a dongle on a laptop wireless, a little weird.
Any ideas?
Hello
Really strange what s
My first idea was a driver update maybe it helps.
You must check the WLan card status in Device Manager.
If there is some yellow exclamation points, so there is a conflict with the Wlan card.If the yellow exclamation point appears or not, you should try to update the WLan driver and then you should check if the TCP/IP protocol settings are set to automatic.
Best regards
-
Unable to connect to the WLAN because FN + F8 does not work!
Can anyone help or I have to do my warranty book. I have some problem with my computer WiFi functionality because FN + F8 does not work. I bought my laptop 3 days ago, and it's a very big problem for me. I do the Wi - Fi connection.
Help, please
Riuno
Dear Ruino
At first, I must say that it will be interesting to know what model of laptop you have. It will also be interesting to know the flash cards exist at the top of the screen if you press the FN key.
Otherwise please go to START all programs utility from Toshiba and click on restart Flash Cards.Please also make sure that the WLAN antenna is turned on. WLAN LED should be on.
Maybe you are looking for
-
Rearrange the toolbars? + Remove some info menu bar?
In the 18.0.2, version I want to rearrange the tabs toolbar so it appears under the search bar, and hopefully, the toolbar of bookmarks. In addition, the Menu bar shows unnecessarily that I am on the page - I don't know who. Is it possible to get rid
-
HP Roar Bluetooth speaker: connection/couple failure - ROAR HP and DELL Laptop speaker
Anyone know how to get my HP Bluetooth speaker ROAR to pair with my laptop DELL Inspiron 15 (series 5559) (10 Windows 64-bit)? I get connection failure messages. I had no problem pairing the speakerphone with my iPhone 6 Plus. The two units (speak
-
Why can I not have all my iTunes on my new phone (6 s)?
Help! Why not transfer all of my music from my iPhone to my new 6 s 5s? 77 albums and more than 600 songs on my 5, 35 albums on my new s 6? The strange thing is a few albums and songs that were not purchased via iTunes have shown up on my new phone a
-
HP Envy: How to reset my laptop to factory setting?
I want to whisk all my data from my computer before giving it away. How can I do this?
-
BlackBerry Smartphones email suddenly stopped working
I run two out of my phone e-mail accounts and one suddenly stopped to receive or send emails. When I try and send an email by the wrong account a small red cros appears next to him and it is not sent. Any ideas?