Tecra A11 - 1F4 (PTSE0E-OM6052EN) which XP AHCI driver?

Similar Questions

• Tecra A11 Touchpad Windows 10 questions

  After upgrading my Tecra A11-182 (PTSE0E-0LP046GR) for Windows 10, I have problems with the touchpad. The cursor jumps from time to time in other places on the desktop, as in Word 2010. Y at - it a new version of the driver for this device? The Windows Device Manager indicates that the most recent driver is installed. Thank you for your suggestions

  Achim

  The cursor jumps because your palm makes contact with the touchpad while you type.

  The advanced settings of Touchpad has an option called "Disable tapping" or «Disable the Touchpad when typing»
  If you do not have these settings, you must update the driver for the Touchpad (Synaptics or Alps) that is compatible with Windows 10.

• Tecra A11 - problems of the more recent/video BIOS

  Hi all

  I just got a Toshiba Tecra A11 the other day which is out of warranty (Refurb). When I got the laptop there is a problem where the photo was displayed at 1024 x 768 and biased (in BIOS). Image 1-2cm off the screen to the left, with over the space of 5-6 cm black to the right of the picture, the low 2-3 cm of the image were also the bottom of the screen.

  I installed Ubuntu Studio initially and attempted to force the display to a wide screen resolution. I didn't have a chance, I also installed Win7, but still with the latest drivers, I had no chance.

  It was strange because the BIOS was displayed in the same way, so, naturally, I decided to upgrade to the latest version of the BIOS. The BIOS of the laptop is quite old (end of 2009).
  I downloaded the update to the BIOS of Toshiba web site and ran the update.

  The new BIOS has been installed and rebooted the machine.
  However there was no image displayed on the LCD screen, windows startup has done successfully, if I connect to an external monitor to the laptop I brush. When starting the laptop backlight LCD lights.

  My question is: what can I do to fix this? Is a tool of recovery or down to BIOS available? Is it possible to reflash the bios? What is recommended?

  Thank you.

  > The new BIOS has been installed and rebooted the machine.
  > However there was no image displayed on the LCD screen, windows startup has done successfully, if I connect to an external monitor to the laptop I brush. When starting the laptop backlight LCD lights.

  This means that everything is ok with the external monitor?
  You can access the BIOS by pressing F2 and you can set it to the default settings?

  Usually, you can switch between the external and internal view using the FN + F5 key combination. It work?

• Tecra A11 - cannot start the BIOS update

  Hello

  I downloaded the latest update of the Bios B2.50 - EC1.80 for Tecra A11-127 (PTSE0E. Wenn I start installing, an error occurs: "this computer is not supported", but my laptop is an A11-127 with Partnumber PTSE0E, why it doesn't work?

  Why is he not possibel to download an old Version of the Bios?

  JSpindler

  Hi jspindler,

  The question is why you want to update the BIOS? This update should be carried out only if it of really necessary. In addition, only the most recent update of the BIOS can be downloaded as it fixes most problems.

  In any case, you need to start the BIOS as an administrator and you should decompress all files from zip archive before start you. Also, make sure that the value added package is installed.

  By the way: what operating system is installed?

• Tecra A11 - 19 L PTSE0E: totally freezes sometimes

  There are times that my Tecra A11 - 19 L is freezes and shows no reaction to any intervention by the user.
  After that a few seconds I heard that the fan goes up to the highest speed-, so I guess that the CPU is running in an infinite loop.

  The only way out of this State is hard to close the entire notebook.

  Can anyone give me a tip solve this problem, or how to locate the faulty component?

  Kind regards
  WIDI

  On this virtual path, it is not easy to tell exactly what is happening, but I imagine that this happens because of some background process that blocks your Tecra. Unfortunately, we can not say exactly what is happening.

  Since when did you notice this? Have you installed any software or doing something that could be responsible for this?

• Cannot open files locked by using fingerprints on Tecra A11 - 17 H

  Hello

  I have a Toshiba Tecra A11 - 17 H - PTSE0E-03402EFR
  OS is Windows 7 64 bit

  Here's my problem:
  I blocked files (image, text) with fingerprints, while I was running Windows XP Professional.

  I copied my files without unlocked on external hard drive, and then uninstalled XP and installed Windows 7.
  After the relocation, the fingerprint reader has stopped working.
  I had to download the drivers and software on the Toshiba site.

  I then put my transferred on the external hard drive on the computer, but now it is impossible to open the file.
  Extension has been changed (automatically), an fpl. came to added after the original extension.

  I tried fpl removed, but nothing happens.
  When I right-click, I do not have the option 'unblock, but rather "to protect the file".

  I understand (reading the forum) that fingerprinting technology TPM consists of a microchip containing a unique computer decryption key.
  Theoretically, it would be possible to unlock my files, since it is the same computer...

  Help me please...

  Please read this:
  [Cannot access protected fingerprint after recovery files | http://aps2.toshiba-tro.de/kb0/TSB9802O50000R01.htm]

  _Issue: _
  A user can access its files of fingerprints protected when you save these files on external storage as for example a network drive and perform a recovery or reinstallation of the operating system on the computer where the files are protected.

  Individual: _
  AuthenTec fingerprint software provides a feature called 'the file/folder protection' which gives the user the ability to protect files without worrying if stored locally, on an external (USB flash memory) or network storage with either a password or stored fingerprints. After you protect the files, they cannot be moved/copied/deleted until the user Déprotège them.

  The first cause of the above mentioned scenario is due to the fact that the fingerprint software "Authentec" creates a link between material installed fingerprint and file system on the HARD disk that functions as a key. This connection is deleted after a formatting or removal of the hard drive of the computer. Without this connection, the files are no longer accessible and the user will not be able to unprotect them since there is no "key", that could unlock the file protection.

  _Resolution: _
  To avoid any loss of data caused by this scenario, * you need to unprotect the files before storing the files on external media * for purposes of backup/storage and then reinstall the operating system.
  Generally, users should make sure to keep a backup accessible to external storage of data corruption and data loss.

• Tecra A11 - less than 10 ips in Skyrim on

  Hello
  I have a Tecra A11 i7 which came with a wiped HARD drive
  I installed win 7 pro and the drivers from the Toshiba site, including the pilot Intel Turbo Boost Technology.

  Even with all the settings set to low temperatures, vid Skyrim runs only less than 10 frames per second.
  I upgraded 4-8gig ram, but this did not help.
  The GPU is Intel, so I can't use Geforce experience.

  I have a Dell Vostro V131 i5 which takes place to better Skyrim.
  But the screen is smaller and i/o ports are 90% of dead, so I'd rather use the Toshiba.

  There are 4 "unknown devices" in Device Manager, but none of them look relevant.

  Does anyone have any ideas?

  Thank you

  To be honest, I have no reasonable explanation because I don't have this video game and can not test it on my Tecra A11 - 19M.
  In my opinion this Tecra is typical business very bad for the games and the machine for office work.
  It does not offer good graphics performance and it is not the best for gaming.

  I use it for daily activities and games use different model Satellite P with nvidia GPU.

• Tecra A11 - 17 C - impossible to boot from LAN

  Hello

  For the last few days I worked on a Toshiba Tecra A11 - 17 c PTSE0E - 02W01GEN.

  I work in a school and we have about 15 of these laptops. I was not the person who did the origonal installation and this person has not left.

  One of the computers needed a re - build. We use an installation of LAN to windows 7 so I put prioraty device that the network card, save it and re - start.

  Then, sometimes with the error PXE - E61 Media Test failed, check the cable.
  Now, I know the NIC works fine beuse it worked before I did any messing around.

  I then checked the other laptop and I get the same error PXE - E61 Media Test failed, check the cable and they all fully functional network ports.

  So I thought ok there is something in the BIOS.
  I found nothing apart an Enable lan option that is enabled.

  It was suggested to relax the default BIOS and then format the hard drive.
  So I thought ok well first I'll try it with the BIOS reset if that does not work, I'll do a format.

  So after that it does not work I thought Okay I'll just clone your laptop work with clonezilla.

  Do I get to the windows flag then instantly the blue screen of death, I can't read it so I is much too fast.

  I thought ok I swap hard drives with the work there. The boots work the clone hard drive just fine without error at all, but the work PC hard drive load the windows flag then blue screen of death.

  I then used a product recovery disc now, it's a drive of windows XP is usless. But I did anyway, and same thing again, it turns the disc fine install XP fine but the flag windows and blue screen of death.

  I finally intertwined a hardrive work 1 different working laptop and a same new blue screen of death in wondows flag.

  It seems to me there must be something on the bios that is
  (A) stop the network port in the bios
  (B) stopping the different hard drives to work in the laptop, even if it's exactly the same laptop.

  They built from the network before for the wondows current installation works, but I have no idea what to do now.

  The error PXE - E61 Media Test failed, check the cable means that the laptop has attempted to boot from LAN, but the configuration of the installation could not proceed.
  Why?
  I m not very well why, but probably there is something wrong with the PXE server settings, etc.

  Are you sure that PXE server has been correctly configured to 100%?
  If this is not the case, check this box.

  > I then used a product recovery disc now, it's a drive of windows XP is usless. But I did anyway, and same thing again, it turns the disc fine install XP fine but the flag windows and blue screen of death.

  Always is Win XP installation could be completed, and this means that the HARD drive should be ok.
  The BSOD could be due to incompatible software or wrong / driver that is part of the recovery disk

  Are you sure that the Win XP Recovery disk you used was the right one?

  How about installation using charge Windows 7 system using the disk of Microsoft?

• Tecra A11 - cannot burn CD - R

  Hello

  My Tecra A11 with Win 7 Pro 64 and a carpet * a DVD-RAM UJ890AS is not able to burn on a CD - R. CD - RW and DVD no problem, but when you try to burn a CD - R I got following error Code: 060277-26 - 2A 031000

  I tried the solution in
  http://forums.Toshiba.com/T5/computer-troubleshooting/error-code-380381-26-2a031000/TD-p/172666
  -without success. There is no filter in case key in my registry.

  I have tried 3 different brands of CD - r, I tried CDBurnerXP and the Toshiba Disc Creator - still the same error. It is written (copy of a music CD) track list, then the error pops up. The CD - R is not usable more after that.

  What can I do? Is it possible to Flash the firmware of the drive from DVD - if yes, where can I get the fw?
  Thanks in advance!

  Hello

  Have which brands you tried?
  I use TDK R and they work properly.

  In addition, I recommend the alcohol laser lens or cotton cleaning tip.
  Has also had problems reading and burning the discs that have been fixed after cleaning the lens.

• Tecra A11 - 005 00K for SCCM OSD mass storage driver

  I need to know the Tecra A11 mass storage driver so that I can laydown XP WIM of images using the SCCM task sequence. Well, any help would be appeciated.

  I tried the driver Intel ESB2 SATA AHCI Controller but need the correct model in the pilot. (IE. Intel ICH7R/DH SATA AHCI Controller)

  Thank you

  You can get the provider and the device for me id?

  You can get this by going to your device manager, the device in question, right-click, select Properties, click details and select the hardware ID from the drop-down...

  copy beyond what is inside of her and post here and I'll see what I can do...

• Tecra A11 & Express Port Replicator II - USB problems

  Hello

  I'm having a problem with a port replicator that I simple couldn't have resolved for months. I'll try to explain this as best I can.

  We have a Tecra A11, which seems to work fine running on Windows 7 Professional. When the Tecra A11 is pluged in an Express Port Replicator 2, not USB ports in the port replicator's work at all. Very good cell phone fees and the LAN switches on the replicator fine, but the USB ports simly does not work under any circumstances. It would also be interesting to note that the green light next to the "eject" button lights never really.

  I downloaded and installed the latest series driver for Windows 7 from the Toshiba support page which has no effect. We had 2 replacements for Toshiba because they also agreed that the previous, we had were not woring correctly, but this obviously was not the case because we still have the same problem with our 3rd unit. The Tecra A11 was sent back to Toshiba with case notes clearly describing the question, and he was sent to us "no fault found".

  Unfortunately, we don't have any other laptops to test on the port replicator. but I'm seriously suspect that the problem lies in the laptop, rather than the port replicator. For any idea or suggestion will be greatly appreciated.

  Kind regards

  Steve.

  Hello

  According to your message, you are not sure if the problem is related to the defective laptop Tecra or express port replicator.
  Hmm theoretically the problem might be related to defective express port replicator or Tecra.

  If found some information on the USB ports and the repliators port:

  + Make sure that the element of Legacy USB in the BIOS emulation is set to "Enabled". This feature only works for the keyboard and mouse. Also note that the keyboard and mouse must be connected before you start the computer. A USB mouse, keyboard or the floppy drive connected to the Port Replicator via any other connection that a hub of the first level, will not work until the operating system has started. +

  I also recommend to check the version of the BIOS; If the most recent BIOS is available, then you need to update this

• My Tecra A11 - 11K new comes with w7-64 bit, but I need w7 32bits

  My Tecra A11 - 11K new comes with w7-64 bit, but I need w7 32-bit because of an old program that I use for professional use.

  I bougth a w7 32 and 64 b license.

  My question is how to install w7-32 more than 64. I think that it is as easy as plug-and - go CD. Yes?

  But I want to preserve utilities Toshiba, other programs that come with the w7-64 pre-installed. Where can I get them? The Toshiba Download Center?
  And which one I need? All the?

  Thank you for your help.

  > My question is how to install w7-32 more than 64. I think that it is as easy as plug-and - go CD. Yes?

  Do you mean that you have a Toshiba Recovery disk?

  If Yes, then it's like you said; put the recovery disk in the CD/DVD drive to start this disc and during the procedure, you will be asked which version you want to choose.
  Then choose 32-bit that s it ;)

• Dual boot with Windows 7 and LINUX - Tecra A11 (PTSE1A - 005-00L)

  Hello

  I bought a new Tecra A11 computer laptop running WIN7 Pro. I want to install LINUX also. This means that I want to run my laptop in dual boot Win7 Pro/LINUX (a Distributor). Please tell me how to do this.

  There are 5 partitions on the HARD disk:
  1 active, recovery partiton 1.46 GB (without drive letter)
  2. principal asset C: start 145,04 GB (NTFS)
  3. active logics E: 78,13 GB (NTFS)
  4 active logical F: 64.25 GB (NTFS)
  5 primary Partition 9.2 GB (no drive letter, the unknown application)

  Hey, I need because I was admitted to a course of RHCE (Red Hat Certified Engineer)

  Please help me

  Hello

  I can't give you a step by step explanation, but most distributions offer today a possibility to coexist with Windows.
  When installing the unused free space will be taken by Linux (with the consent of the user of course!)

  What exact configuration you need is impossible for someone else to say, but I would say to make the space occupied by the F player available for Linux.
  You seem to have of enough space for Windows and Linux operating system doesn't have much.

  Some thoughts about setting up your score:

  I touch NOT 1,2 and 5 no matter what. They are your system and a system of internal partitions (recovery and data environment) and wouldn't it be fun to lose.

  1 active, recovery partiton 1.46 GB (without drive letter)
  2. principal asset C: start 145,04 GB (NTFS)
  3. active logics E: 78,13 GB (NTFS)
  4 active logical F: 64.25 GB (NTFS)
  5 primary Partition 9.2 GB (no drive letter, the unknown application)

  Then choose a Distro (Ubuntu, Mint, Fedora and OpenSuse - suggestion Fedora will be as close as possible associated with RedHat) that will guide you in the steps to allocate space for Linux.
  I suggest however to remove the disk F in Windows for Linux does not start from resizing all partitions.
  I do not know which works perfectly, but will just take time, and will most probably remain pretty useless drive F.

  If you have valuable data on your device, make sure to save! No software comes with warranty :)
  Last but not least - make 100% sure to create a collection set using the Toshiba Recovery Media Creator before you start the installation of Linux.
  If something goes wrong you have the opportunity to put the unit in factory condition.

  Good luck and keep asking you if you need extra help!

  Tom

• Tecra A11 - serial port does not

  I have a Tecra A11 running windows 7 Professional (32-bit).
  My serial port does not seem to work as I am no longer able to connect to the industrial PLC automation which requires the connection to the serial port for programming.

  Some of the software I use is a RSLinx, Easysoft and others.

  Any help on this will be greatly appreciated.

  Hello

  The serial port is properly recognized in Device Manager?
  Do you have signs of yellow exclamation point there?

  Try to remove the serial port of the Device Manager and reboot the machine to get this recognized again port.

• Tecra A11 - 17N - reading Blu - ray?

  Running a Tecra A11 - 17N with Windows 7 and an eSATA (or USB) plugged the external Blu - ray writer. The supplied software (Cyberlink) for Blu - ray playback has an "Advisor", which reported on the ability of the various functions of reading Blu - ray discs (BDs). I appears that it is only the graphics card Driver / which is the problem, see the picture here:

  [http://www.headspin.plus.com/store/tecra_bd.JPG]

  The 'i' link info tells me to check that everything is up to date with Intel drivers, what I did (I think!).

  One got a Tecra reading Blu - ray discs?

  If I understand you right you have problems to read the external ODD connected Blu - Ray disc?
  With other preinstalled words Cyberlink doesn't have access to the drive externally, right?

  To be honest, I'm a bit confused because your laptop has no internal feature of Blu - Ray and Blu - Ray player. According to the specifications of the computer laptop Toshiba DVD player must be installed on this computer.
  are you sure you've got this Cyberlink with original Toshiba recovery image?