Tecra A4 CD/DVD drive inaccessible function / incorrect

I have TECRA A4 with Mat * one CD / DVD R + RW 830 s with Windows XP SP2 installed (as purchased). Whenever I tried to burn a CD or DVD I get the message "D:\ not accessible; incorrect function ". When I put the blank CD it does not detect it. and when I use sonic (came with Toshiba Notebook), it detects the drive and the CD but can not burn after a few seconds of engraving, the CD is ejected and calls for a new CD. When I look for troubleshooting all it says is 'Try new CD, perhaps that the CD is not good..' Toshiba with Mat * a DVD player has consumed hundreds of my CD with the last few months, and I'm totally frustrated now with Toshiba and Mat *. Had I knew before this problem I don't him would not have bought. I do not use any other registration of software, so there is no problem of conflict. Can there be any help or solution to my problem? I need to burn data from my place of work and the purpose of having Toshiba with CD/DVD burner is simply turn out to be a very profitable investment, because it cannot burn everything. Your response and your help will be appreciated.

S. Motru

Hello

I read on some sites that, sometimes, the Sonic application could cause burning malfunction or the reorganization of DVD.
Try to remove this software and use Nero. Check the above mentioned option.
Also remove the drive from the Device Manager and rebooted again the reader should be recognized again.

Maybe it helps

Tags: Toshiba

Similar Questions

  • Portege M400 - CD/DVD Drive not accessible, Incorrect function.

    Hello

    We have 1 machine that shows the above error, and strangely enough, it is only to show this error when you try to play the DVD. CD is reading and fine engraving. The H/W is a carpet * a DVD - RAM UJ-8425. The drive is correctly activated and we have about 100 other machines with exactly the same formatting and set up using XP that do not display this error. I changed the H/W and uninstalled and reinstalled the drivers of devices, but without result.

    Anyone has any ideas that can help?

    See you soon

    Steve

    When you get this error message exactly? You get this error message if you're looking for a DVD or watch a movie on DVD?

    In your case, I would try to remove the upper and lower filters. Then follow this work around:

    (1) run Regedit (start > run > Regedit)
    2) go to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class {4D36E965-E325-11CE-BFC1-08002BE10318}
    (3) in the right pane, delete the "UpperFilters" key and delete the key "LowerFilters".
    (4) restart.

    Good luck!

  • My pc DVD drives non-functional drive

    In it these last daysas my my pc dvd player has stopped working and it appears that the hp DVD-RAM UBBI SATA CD-ROM drive is missing and I tried everyth ing to reinstall disk you required, but nothing works, please help

    Hello:

    Please read the info at the link below.

    Normally one of the resolution - 2, 3 or 5 steps solves the problem.

    http://support.Microsoft.com/kb/314060

    If none of the steps in the article for you work then unfortunately I do not have any other suggestions that you can try.

  • Tecra S3 and the replacement DVD drive

    Hello

    Portable model is Tecra S3 PTS30A-03E008
    DVD disc model is UJ - 832
    DVD player reference number is G8CC0002Q120

    The DVD drive no longer works and I'm looking to install a new one. Is the Toshiba Ultra Slim Bay DVD SuperMulti Drive
    Part number - PA3473U-1DV6 the correct replacement drive?

    Thank you

    Warren

    As I see in the paper manuals for your Tecra s user I can see two optical disk drives are listed as compatible:
    MATSU * A UJDA765
    MATSU * A UJ-832

    Reference numbers are not known to me, but I recommend you to use only compatible devices.

  • Wanted - cd/dvd drive Tecra M2 caddy assy

    An urgent need

    I bought a Tecra M2 without a cd/dvd drive.
    Bought some naked replacement dvd drive - require all parts of carriage or a unit complete and good cheap which is blown to fly parts.

    If you have it please email me - [email protected] or telephone 01395 272057

    I would like to oreganise something before Monday because the unit is shipped to Tanzania so far.

    See you soon.

    Stephen Diarmid

    Hello

    Contact service partner in your country. I'm sure they have a lot of them, and it should not be stopped. I put t believe that these parts be expencive.

    Good luck!

  • Tecra S2 - NEW cd/dvd drive

    Hello
    I just put in a new cd/dvd drive on my computer laptop tecra s2.
    Only problem, when I start under xp the cd/dvd drive works perfectly, but I need to install vista on my computer and my bios does not recognize this drive. When I change the priority of the first cd/dvd boot it skipps just my cd/dvd drive and loads as usual.
    help please

    The new drive is perhaps the correct master/slave settings.

    Have you tried a different CD Bootable? Maybe the Vista disk burned correctly (if it is a rewritable disc)

  • Tecra S5-10 X - CD/DVD drive causes BSOD with new CD not burned.

    Hello!
    I have a laptop TECRA S5-10 X with windows XP (downgraded from Vista)

    My computer has trouble dealing with discs not burnt from the interface of microsoft. Make a right click on the drive takes more than 20 seconds to answer. After 2 - 3 times (sometimes right the first time) with or without ejecting the disc, I get a blue window of death "DRIVER_IRQL_NOT_LESS_OR_EQUAL".

    I tried the Toshiba DVD Diagnostics passes.
    I tried to uninstall and reinstall the driver.
    I tried to do repair for windows
    I installed service pack 3 for Windows XP
    I've updated the bios
    I've also updated the (Microsoft says it might be useful) NvIdia video card driver

    Nothing helps.

    I'll be very happy to get any other suggestions that will help me avoid a reinstallation of windows.

    Thax in advance

    H.

    I think you should try to remove the top and lowerfilters as Akuma said. This often solves problems with the CD/DVD drive.

    In the worst case, you must reinstall Windows.
    You also have this problem only with XP or Vista?

    I doubt that it is a hardware problem so reinstall Windows could solve it.

  • In Tecra A8 DVD drive replacement

    My DVD player is down, I already have a replacement drive.

    Does anyone have an idea where the output of the DVD player is located so I can get out? I unscrewed a few screws, but it won't come out.

    Tecra A8 is the same as the Satellite Pro A120

    To swap the DVD drive, you must remove the keyboard.
    It's a little tricky and in my opinion if you n t have much experience with this you should go to a local ASP and ask a technician for help.

    Here, you can search an ASP:
    http://EU.computers.Toshiba-Europe.com-online decision-making supported downloads & => find an authorized service provider

  • HP Pavilion p7-1234: functional CD/DVD drive will not boot Clonezilla disk recognize

    Have three HP p7 in small desktop running Win 7 64 bit. (Avast free version)

    None of them will recognize a bootable Clonezilla ISO or Zip, whether on CD/DVD or USB.

    Measures already taken:

    BIOS set to boot from CD/DVD

    In turn the BIOS configured to boot from USB

    Have used any compatible version of Clonezilla downloads based on my operating system and the processor, including the generic i686 ISO and Zip. (and makes bootable USB drive)

    CD/DVD and USB function perfectly well otherwise. Able to access the other disks and USB media with no problems.

    Also able to see the Clonezilla ISO when I look at the CD/DVD drive.

    It starts simply what whether Clonezilla.

    If someone has encountered this, I would like to share your experience.

    Thanks for your time.

    One rookie mistake.

    Problem:

    Bad, I carved the Clonezilla ISO to CD/DVD disc.

    Solution:

    1. download the ISO Clonezilla appropriate for your computer, on your desktop.
    2. place the disc in the CD/DVD drive
    3. "right click" on the Clonezilla ISO on your desktop.
    4 Select "Burn Image" and follow the default values.

    Now you have a proper boot Clonezilla disk.

    Next:

    1. make sure the BIOS is set to CD/DVD is bootable.
    2. place Clonezilla disc in open the tray of the CD/DVD drive.
    3. restart the computer and close the CD/DVD tray
    4 put your finger on "F9" key and now wherever the blue HP screen appears, press "F9".
    5. boot Menu loads.
    6. move arrows down to the first line indented under "ATAPI CD/DVD DRIVE...
    SATA2 or SATA3 will be according to your system.
    7 hit ENTER.

    Clonezilla immediately, boots and loads.

    I hope it works for you.

  • Can Tecra M1 - I use my DVD drive in an external enclosure?

    Hello

    I had one laptop Terca M1. Now, I have another PC Toshiba laptop which Bay is not compatible with the M1. So I can't use my 'old' on this new laptop dvd player.
    Is there an available accessory Slim external enclosure to use my dvd drive external usb?

    Thank you

    HP

    Hello!

    Which is a good question, but as far as I know that it doesn't have these adapters.
    But you can look on eBay or ask your computer dealer for this.

    And I agree with Akuma. I think the best solution would be an external USB DVD drive.

    Good bye

  • CD/DVD drive is not detected or functional

    Title:

    FixIt error 0 x 80092003

    Restore the computer to factory settings, ran RegistryBooster to fix registry errors and defragment, CD player continues to ruin, tried to run FixIt, but get error 0 x 80092003 each time. What should I do?

    Hello

    You can try to run the manual steps from the link below.

    Your CD or DVD drive is missing or is not recognized by Windows or other programs

    http://support.Microsoft.com/kb/982116

    Hope this information helps.

  • DVD drive does not write - Satellite M40X-175

    Im having a problem with my dvd. I tried to burn my movies, music and my files on a dvdr or cdr, I tried DVD - RW and CD - RW but I do it every time gives error "d:\ is not accessible incorrect function". but when I try to watch a dvd movie or use my music cd, it does not work. He reads. Does this mean that my dvd drive cannot be read and not write?

    [Edited by: admin on 4 February 06 20:23]

    Hello

    Satellite M40X sounds new enough to have CDs of feature writing. Seems to me a HW question but you can try:
    1 - Clean the blank CD with a cloth dry
    2 - blow to the goal and do not forget that there is no dust
    3. you can uninstall the driver from
    -> Panel-> system-> hardware-> Device Manager-> DVD - RAM-> (right click) properties--> driver uninstall-> restarting your laptop.

    If they do not contribute, you can contact a Toshiba authorized Service partner. You can find the one nearest to http://217.45.123.236/toshiba/resellerselector.nsf/WebServiceProv?OpenForm

  • My CD/DVD drive will not appear in the Device Manager, but present in the BIOS.

    DevCon didn't find it. It will not open even if I don't get to Device Manager and check for changes to the system. I deleted the registry entries upper and lower limit. Any other suggestions? For additional emphasis, he does not show even in the Manager of devices so I cannot restore or reinstall the drivers from there. It might also help that I use Vista Home Premium on a Compaq Presario F755us.

    Hello

    (1) does the BIOS see the main hard disk drive or a secondary hard drive?

    (2) remember to make changes to the computer before the show?

    You know may not be not that most systems are set to show only the splash screen. If you go into the BIOS Setup, it should show the disks that have been detected on two primary and secondary IDE channels.

    Note: the basic procedure to change the setting of the disk controller is to restart your computer and enter the system BIOS. The most common method is to press F2 to enter Setup, (another PC may use a different key). On the BIOS screen, find the setting that offers the AHCI, ATA or IDE and RAID. If the parameter is set to AHCI, change the setting to ATA. Restart the PC on the Windows installation disc

    Warning: Incorrect settings in the system BIOS can cause your PC function incorrectly. If you are not familiar with the configuration of the BIOS of the system, you must contact the PC manufacturer for assistance.

    Try the steps in the following article and check if it helps.

    My drive does not appear in Windows Explorer

    http://support.Microsoft.com/kb/330140

    Registry warning: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: http://support.microsoft.com/kb/322756/

    You can also check the following items.

    CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista: http://support.Microsoft.com/kb/929461

    Error: A required CD/DVD device driver is missing - when you boot Windows 7 or Windows Vista installation disk: http://support.microsoft.com/kb/952951

  • My laptop does not recognize the cd/dvd drive, gives the error message 19 and cannot load/reload driver TSST. Any suggestions?

    Device Manager says: "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged (code 19).»  Mr. Fix - it (Microsoft) indicates the CD/DVGW TSSTcorp TS-L632M ATA Device drivers & filters are corrupted or damaged.  Mr. Fix - it could not download the updates/drivers for TSST.  Mr. Fix - it has been able to get the computer to recognize, but unable to take the function of CD/DVD.

    Hello

    Perform the following methods and check if it helps.

     

    Method 1:

    Please run the difficulty of following article and check if that helps.

    Your CD or DVD drive cannot read or write media

    http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

     

    Method 2:

    You can read the following article to see what might cause this problem.

    When you insert a CD or a DVD, Windows Vista may not recognize the disc

    http://support.Microsoft.com/kb/939052/en-us

    If you had recently upgraded the computer to the Vista operating system or install the Service Packs, then try the steps as described in the following article.

     

    The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista

    http://support.Microsoft.com/kb/929461/en-us

    Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

     

    How to back up and restore the registry in Windows

    http://support.Microsoft.com/kb/322756/  

    Hope this information is useful.

  • CD/DVD drive is not detected.

    For some reason my CD/DVD drive is more functional.  I can't even eject the disc that is in it and it does not recognize.  I have searched for corrections and so far all I've done was to remove the filter lower and upper filters in the registry.  I'll try to uninstall and reinstall this drive, but I can't even find on device manager

    Any help would be appreciated... Thank you!

    Here is the solution I mentioned earlier. Good luck and thank you Greg!

    I thought I had posted the solution.  The upper and lower filters need to be refreshed.  Here is a solution I found on the Adobe forums. http://kb2.Adobe.com/CPS/402/kb402306.html

    Refresh the CD and DVD drivers list in the Windows registry.

    Warning: The registry contains information on the system that are critical to your computer and applications. Before editing the registry, be sure to make a backup of it. Adobe does not provide support for problems that result from incorrectly modifying the registry. Adobe strongly recommends that you have experience editing system files before you modify the registry. For more information on the Windows Registry Editor, see the Windows documentation or contact Microsoft Technical Support.

    To refresh the CD and DVD drivers list in the Windows registry:

    Important: After you refresh the list of drivers in the Windows registry, you may need to reinstall any other CD or DVD on your computer to write applications. If you restart Windows after this procedure and other burning CD or DVD applications do not recognize the CD or DVD drive, and then reinstall those applications.

    1. Uninstall your Adobe application.
    2. Open the Registry Editor:
      • On Windows 2000 and XP: click Start > run. Type regedit in the box text open, and then click OK.
      • On Windows Vista: Click Start. Type regedit in the search text box, and then press ENTER.
    3. In the left pane of the registry editor, navigate to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class and select the {4D36E965-E325-11CE-BFC1-08002BE10318} key, which appears as a folder.
    4. Select file > export (Windows XP and Vista) or registry > export a file from the registry (Windows 2000).
    5. In the export registry file dialog box, select the branch selected under export range, name the file (for example, CDDVDkey.reg) and click Save to save the file to the desktop.
    6. In the Panel to the right of the registry editor, select the LowerFilters line, and then choose the editing command > delete. Click Yes in the dialog box confirm deleting key.
    7. Select the UpperFilters line, and then choose the editing command > delete. Click Yes in the dialog box confirm deleting key.
    8. Close the registry editor.
    9. Open the Device Manager:
      • On Windows 2000 and XP: click Start > Control Panel. Double-click the system icon, click the Hardware tab, and then click Device Manager.
      • On Windows Vista: Click Start > Control Panel, double-click System, and then click Device Manager in the task pane.
    10. Click on the symbol more then to CD-ROM/DVD-ROM drives.
    11. For each listed DVD-ROM or CD-ROM drive, select the icon then choose Action > uninstall.
    12. Restart Windows.
    13. Windows will automatically detect and reinstall your CD-ROM or DVD - ROM drives. You can check that the drives are installed in the device (see step 9) Manager. If the drives are not present, open Device Manager and choose Actions > Scan for hardware changes.
    14. Reinstall your Adobe application.
    15. Restart Windows.

    Important: If this solution doesn't solve the problem with the application you reinstalled, then you must restore the CD and DVD drivers list in the Windows registry.

    To restore the exported CD and DVD drivers list:

    1. Double-click the registry key that you exported.
    2. Close the registry editor.
    3. Restart Windows.

Maybe you are looking for

  • author of iBook did not support Arabic and Urdu, I want to make Urdu ebook How can I

    I have Purchesec mac do ebooks Urdu but author ibook did not support Arabic and rtl language urdui.e's note

  • Screen turns off and the keyboard hangs on satellite

    My laptop screen goes black all of a sudden but I still hear it work and sometimes the backlight stays on but the keyboard hangs totally.I have to restart every time. Upon restart, it indicates that windows not stop correctly. I was wondering if mayb

  • Satellite A200 - the fan speed with BIOS v2.50

    Hello I have laptop Satellite A200 - 28 p PSAE6E I bought 2 monts ago. I made a terrible mistake 2 days ago and updated the BIOS on the computer of the Toshibas website to v2.50. fan began acting very strangely that he starts every time that runs for

  • HP laptop battery does not load

    Recently, I thought that my laptop died a GPU, but it wasn't the problem, I changed my battery sister and my entire battery and I used his and my laptop turned on miracle, but the power of the battery keep going down by 2, for example if the power of

  • Access Violation PCHealthDocunzipped.exe

    I run Windows XPI regularly "breach of access to the address 006249 has 8 in module PCHealthDocunzipped.exe"appear with deaf guests during my work or sometimes when I turn on first.  My only way to continue is to shut down my computer.Can someone hel