Tecra A8: Problem with the USB printer connected to the Port Replicator III

Similar Questions

• Problems with the port replicator USB 2.0 after installing Windows XP - SP2

  Hello world

  I have a Satellite M30 742 with MS-Windows XP Professional installed. I plugged most of my external devices to him through a port replicator Toshiba USB 2.0. Everything seems to work fine until I installed Service Pack 2.

  Therefore, starting my laptop computer is an adventure to recognize random port replicator: usually four USB ports are recognized, but the ports series and parallel, keyboard and mouse ports are ignored, with a message "unknown USB device".

  Uninstalling and reinstalling, them or their drivers are a vain effort, since Windows keep ignoring them.

  However, in other occasions, they are recognized without problems (even if windows insist on installing their drivers each time that it finds, even if I have already installed a large number of times).

  Please, you have an idea to solve this problem * boring * problem?

  Thank you very much in advance,
  Ricardo.

  Hello

  what you might try is to reinstall the chipset driver because I think that the USB is connected to the chipset.

  In my opinion the Windows upgrade had changed the pilot USB from Toshiba a MS a. So the Port Replicator is not recognized all the time.

  Rudi Bye

• Problems with an external monitor with the Port Replicator III and M100

  Hey all.

  I just returned from a trip where I took my laptop. Plugged into the Port Replicator port, started and everything was fine. Then after an hour or two, the monitor stopped receiving a signal. I repositioned the laptop and everything was good again. He then loses signal once again, and I was not able to get a signal via the port replicator since.

  The monitor works fine through the hole at the rear of the M100.

  I checked the pins on the Port Replicator port and portable, none folded and tried to clean any dust etc. Still no signal to the monitor.

  Someone has ideas of how to do to solve this problem?

  Jamo

  Hello

  The Toshiba 3 mobile extension is responsible for the good condition of the duplicator 3 market. Try to reinstall this utility and also check the page of the Toshiba driver for updates.

• Re: Tecra A10 - USB problem on the port replicator

  I have a Tecra A10 and sometimes, when I work with her, the devices USB stopped responding if they are connected to the port replicator.
  If I connect them to the laptop, they work fine.

  I tried to update the BIOS but now when I turn on the laptop it freezes when Toshiba red letters are displayed on the screen. I can work with the laptop properly deattached starting from port replicator.

  Have you tried to load the default settings in the BIOS after the update?

  If you have external devices connected to the laptop they remove and try again in the duplicator.
  Maybe you should also update your laptop chip set driver. You can find them on the Toshiba site.

• Tecra S1 stops when you use the Port Replicator III

  Hello

  I ve you have a problem with a Tecra S1 Notebook and Port Replicator III. When I anchor the portable station, it turns off immediately. It doesn´t so serious I m in Windows or not. The same notebook works in a Port Replicator II without any problem. My first thought was, the Replicator III may be damaged, but I tried with an another Tecra S1 and it worked! Can someone help me with this?

  Thx a lot!

  Mathis

  Hello

  AFAIK that should not be any problem as Tecra can be used with the two PRs. The only thing I can recommend is to reinstall the Toshiba Mobile Extensions.

  Good bye

• audio off when it is associated with the port replicator

  I use Windows XP with my Thinkpad T400 and I bought a Lenovo port replicator model k33415 with my computer.  I have a keyboard and a mouse attached to the Port Replicator port as a PDA sometimes.

  Whenever the port replicator is connected to the computer, the computer speakers do not work and I hear no audio.   When I restart the computer without the attached port replicator, the computer speakers are working fine.      I've tried everything!    Any ideas?

  Hello!  In fact, I fixed it on my own.   Under sound properties I adjusted the audio settings for 'Conexant HD', he made my default device, and under AUdio and then "Advanced", I needed to set speakers to computer speakers.  What I haven't done yet we see if this turns off audio when I unplug the duplicator... so I guess I need to change the default device.   You may not have the same problem, but in any case, good luck!

• Portege R500: external monitor does not work with the Port Replicator Port 2 and DVI

  I have a Portege R500 running Vista with a slim Port Replicator II and digital monitor Viewsonic.
  I connected the monitor to the DVI port on the port replicator and got it to work OK.
  Press fn + F5 would switch between the computer screen and the external monitor.

  Then it stopped working, and I can't make it work at all. F5 recognizes just the laptop screen.

  If I connect an analog display, it is fine, and I can pass between the two screens without difficulty.

  The strangest thing is that, if I reboot when the Portege R500 is docked, the digital monitor begins by displaying the boot sequence, but then the signal is lost as soon as the screen stops the display of the progress (in low resolution) bar.

  I spent an hour on the phone to support Friday, and he made me nowhere.
  They finished by saying that he should never have worked! So what is the DVI port because then?

  Any ideas?

  David

  Connect your monitor directly to your laptop and see if it is recognized and you can go through FN + F5 between the two views.
  If it works, then connect with port replicator, and then try again.

  It's probably best if you reinstall display drivers. Maybe there are new too on the download page.

• Tecra Z50-A-12 X is not properly connected to the Port Replicator III

  Hello

  I just bought a TECRA Z50-A-12 X with HI-speed III 120 replicator Port Replicator.

  It works but the computer is not stable and I fear that this will eventually damage the port see me problems when using.

  Indeed, the PC sits well in the Replicator.

  Is there a solution or did not have this app?

  Thank you for your response.

  Nice day

  Hello

  Please don't get me wrong, but you should clarify this with Toshiba directly. Here on this forum, you can hear some useful opinions and comments, but I think you should get info straight from Toshiba directly.

  You can also do is to contact the nearest Toshiba service provider and ask for help. You can visit ASP and demonstrate how it works and I hope that you will get a professional opinion on this problem.

  Long ago I had a Tecra laptop with port replicator, and he was well in place and really does so port replicator he not there no danger of damage to the small port located in the lower corner.

• problem with the ports of the two SLM2048

  Hello:
  I have a problem with two models of SLM2048.
  I only as configured in these devices was 4 VLAN and link aggregation port between these devices.
  I detect some Don t work ports (I connect to a workstation in the port and the Don t upward, but in the other port if upward)
  Could be a hardware failure? or maybe the switch block these ports?
  Best regards

  I'm not sure that I fully understand your port problems.  Is this a failure of single port or you have a problem of end-to-end between ports on two different switches?

  Andrew Lissitz

• Just bought Wndows Vista and having problems with the port for Palm 125

  I just bought a Windows Vista-based computer and have problems with getting my 125 Palm to synchronize with the desktop computer.  I get an error message saying: "No available Com1" what should I do?

  Thank you

  Frustrated

  Don't ask me the procedures step by step that I did, but I finally success!  I uninstalled Palm Desktop and started from scratch.  I unplugged the Hot Sync cradle by the USB port, then I installed Palm Desktop from my drive and then update Palm Desktop on the Palm for Palm M125 site.  It still does not, I manually added a port and manually changed to COM1.  I then pressed the Hot Sync button and in the Device Manager, a folder has become available "device named" with Palm Desktop as a subfolder.  It is always active, I updated my computer for Palm USB driver.  Miraculously it worked.  Thanks for your help, but as usual everything it needed, it was patience and trial and error to solve the problem, since it does not seem to be a quick fix related this topic.

  Message relates to: Palm m125

• Tecra S1 - problems with the touchpad after update BIOS to 2.50

  Hello
  After the BIOS-update to version 2.5, the touchpad does nothing. From the docking station, the l' option option mouse PS2 works without any problem. Starting late, the touchpad no longer works. Normally - before the update - the touchpad began its work immediately after starting not rooted.
  What can I do to reactivate the touchpad?
  Juvenay clevain

  Hello

  Are you sure that your touchpad was not disabled?

  I mean the FN + F9 key combination to activate and disable the touchpad.

  This is why you should check this first.

  On the other hand a 3rd mouse driver part could affect the functionality of touchpad too.

  In my opinion, you should try to reinstall the driver for the touchpad and test it without connected part 3 mouse.

  Good luck

• Tecra S3 - problems with the new ram in slot B

  Hello
  I have a new 2 GB of ram. When I put it in the slot A (location B is empty) it works perfectly. When I put my old ram (1 GB) in the slot B now and try to powerup, I hear beeps: 1 x long and short 4 x. The screen remains black. Do you know what it is?
  Thanks for your help!

  Hello

  The beeps mean that the POST (power on self-test) could not be passed correctly.

  Your dysfunctions of slit B or the laptop needs 2 modules of memory installed in two slots in order to use the also the second memory location.

  But my assumption is that your second slot may be defective.

  Welcome them

• Trouble with the port replicator. Use of 2 screens and now only have 1

  Have a new laptop. (Lenovo) also bought duplicator. Hung, everything works fine. Got online to get assistance with updates is not crowned success, after that I just use of screen on laptop, any other monitor disappeared. Can't get it back

  Hi Tom,

   

  Thanks for posting the question in the Microsoft Community!

   

  You are unable to get the display of multiple monitors.

   

  I suggest you to contact Lenovo to get help for this issue.

   

  You can try to get help on the site:

  http://support.Lenovo.com/en_US/feedback/contactsupport.page

   

  If you need any other assistance, let us know and we would be happy to help you.

   

   

   

   

• Problems with the Display Mode target on end 2009 27 "iMac

  Used late 2009 iMac 27 "in the view target in conjunction with a Dell XPS tower with i7 processor, Windows 7 and the best graphics card I could afford at the time connected by HDMI to mini display port cable.  Worked well for years.  Set aside Dell for a few months and the update of the iMac to El Capitan OS 10.11.3.  Recently tried old setup with same Dell PC and was able to move from Mac to PC, but the PC screen resolution was at the lowest setting. I got an error message when enabling/disabling to PC who said there was a problem with the port causing mini display of the system back to the lowest resolution. Impossible to reset at a higher resolution.

  I tested the Dell PC on another monitor, and it works very well at higher resolution (2560 X 1440). Now, when I reconnected it to the iMac (which works fine), the screen becomes black.

  Is it possible that the operating system upgraded (El Capitan) is not compatible with the targets using mini display port Display Mode?  Any ideas?

  Use your iMac as a display with the target - Apple Support Display Mode , also consider having a bad cable or connection. Does not hurt to try different cables, they can and will the bad!

• Portege Z30 16 GB with high speed Port Replicator III and two monitors - resolution

  I have a Portege Z30 with 16 GB of Ram, connected to a Toshiba high speed Port Replicator III which is connected to two monitors running in mode extended.

  The monitor attached to the first section of the video is 1920 x 1200 running.
  However the second monitor is only show support for a maximum of 1280 x 1084.

  The monitors are identical, and both are connected by DisplayPort cables.

  I tried to lower the resolution and save the settings on the first monitor to see if it offered options on the second monitor, but the options remained the same.

  At this point, I have narrowed down to 1280 x 1024 so that it conforms to all the monitors but would like to a plus-res solution.

  Does anyone know if there is a fix/work-around for this?
  If this is a hardware limitation, has anyone tried a USB 3 to DisplayPort adapter in a similar configuration?

  Thank you!

  At the same time using two displayports?
  I wonder how it is possible, because of my knowledge it is not possible... as far as I know the Port Replicator III supports two DisplayPorts but you could choose and use one of them...

  In any case, you can use both with a lower resolution, I guess that this problem can be caused due to incompatible display drivers.
  I suggest you to uninstall reinstall or update the display drivers and check if it helps