Tecra A9 - after CPU fan upgrade works constantly at full power

Similar Questions

• Tecra S3-130: why fan still working

  Hello

  The fan is too loud on my laptop Tecra S3-130, because it doesn't always work, never stops. I tried the settings in the properties "Toshiba Power Saver", but after changing anything that the fan starts working again in a few seconds, despite the ACPI temperature is 46 degrees Celsius only, not much higher. This fan of work is always very disturbing.

  Thanks for any advice in advance.

  Kazi

  Hello

  The temperature is 46 degrees Celsius, only because the fan works properly. If the fan doesn't run the temperature climbs. I put t know how you use your device, but if you are working with programs of high performance fans should run because of high utilization of the processor and overheating problems. In addition if cooling method is set for maximum Performance the cooling fans work up.

• Tecra A11 - 11 L - fan still working

  I already turned on eco mode and 1 core CPU temperature is 22 ° C and core 2 is at 15 ° C.

  I have even an SSD in this laptop, so it should be cool and silent. Cold air comes out of my laptop and the whole case is still warm (really, I hit the computer laptop while at the top of the page down, everywhere!), but according to PC Health Monitor the rest fan continues to operate at 50%! It is certainly stronger than my old laptop.

  Is this a problem with my laptop, or the A11 series has this problem?

  You come in on the problems
  I put t see any problems
  The fan operates at 50% and therefore the temperature is low
  If the cooling module would not go, then the temperature would be much higher

  In any case, you can check the Win7/Vista power management.
  http://forums.computers.Toshiba-Europe.com/forums/Ann.jspa?annID=41

  In power management, you can set the performance of cooling on the lower level.

  I also recommend updating the BIOS. If a newer version is available, and then run the update.

  Welcome them

• Re: Equium A100 - 02 k - CPU fan stopped working

  Hi guys can all help to repair my Toshiba Equium A100 - 02 k model, it stops automatically every 15 minutes by overheating.
  It started after me using compressed air to clean my laptop. I don't know why something went wrong on the inside when I used compressed air to clean near the fan at the bottom of my laptop.

  could someone suggest me wat I can do in this situation, should I open the laptop and change the fan or is it possible.
  If I have to open so please let me know how to do this.

  Thanks and greetings

  Hello!

  I think that this question can be easily answered: the fan must be exchanged if it s does not.

  Of course you can do it by yourself, but disassemble the laptop is a bit tricky and you have to remove a lot of screws and parts. I put t know if you have enough experience to this
  If this isn't the case, you can contact the nearest authorized service provider. Technicians can do for you and on the Toshiba site, you can search the nearest ASP:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported downloads & => find an authorized service provider

  Good bye

• Dell Vostro 200 Mini CPU Fan upgrade

  Does anyone know what kind of CPU heatsinks are compatible with G33M02 motherboard that comes with a Dell Vostro 200 mini tour. The fan makes a lot of noise and I wanted to buy a replacement.

  Kuranado

  You need Reference Dell #JY167

  https://www.discountelectronics.com/product?product_id=3362&Product_Model=104

  Bev.

• CPU fan broke on Satellite A215-S7444

  Hello

  My Satellite A215-S7444 CPU fan stopped working which causes my CPU become very hot.

  After 5 minutes of idle my laptop turns off which makes it almost useless to my laptop.
  After reading a few forums, I decided to disassemble my laptop to check that there is no dust or debris obstructing the fan.
  However, I got so far as to take off the keyboard because I didn't know how to take off the high black/silver (please link to image).

  http://I201.Photobucket.com/albums/aa287/istanlfc_album/laptop.jpg

  Could someone please help me with this problem, I use on a daily basis of the laptop and it is important for my studies.
  I don't mind it sends out of Toshiba for repair cost.

  Jin

  Perhaps, you will find it useful:

  http://www.irisvista.com/tech/

  Be careful to disassemble the laptop, there may be hidden media

• CPU fan working after upgrade

  After the upgrade of my HP Pavilion TV m9058 for Windows 7 64 bit, I noticed that the CPU fan does more than before the upgrade. The fan runs almost all the time.

  My computer is standing in the same place as before. I removed the dust inside the computer

  The fan noise is very annoing, so if anyone has an idea of what to do, please let me know...

  Thank you

  Tommy Nilsen

  Problem solved...

  There was a thin layer of dust from the fan to the heat sink.

  Not easy to detect...

  

• My slimline s5212y cpu fan seems to work fast constantly.is it an update of the bios for this?

  Hello

  I replaced the motherboard on a tower of s5212y slimline (the same Board of model). Everything works fine, but the cpu fan seems to work too quickly, constantly. Y at - it an update of the bios that fixes this?

  ICU wrote: Hi, I have replaced the motherboard on a tower of s5212y slimline (the same Board of model). Everything works fine, but the cpu fan seems to work too quickly, constantly. Y at - it an update of the bios that fixes this?

  Hello uti, I checked for an update of the BIOS of your system but could not locate a.

  You can try to reset the BIOS, either by removing the CMOS battery, or perform the jumper pin method.

  If you remove the CMOS battery, boot the system and enter the BIOS and reset the time, day, and year, save these settings and reboot the system.

• Re: Tecra M5 PTM51E - CPU upgrade question

  Hi, I have Tecra M5 PTM51E model with processor Yonah T2600 (2.16 ghz, 667fsb) core duo, a few days ago that I just replaced the processor with core 2 duo - Merom T7400 (2.16 ghz, fsb667) and everything works almost well... the processor is correctly recognized, I was able to install win7 64 bit.

  The only problem I have is the fan speed, it goes full speed laptop to stop, I have the latest BIOS 3.70, Toshiba Power Saver - no matter what I put the fan goes 100% speed, temperatures are ok, HWmonitor presents the 28-30 C idle and 60 in stress and fan was cleaned up during the replacement of the central processing unit.

  I guess I need media diagnosis/service of toshiba to set correct values for the speed of the fan on the processor?

  I appreciate any suggestions, thanks!

  > I upgraded the CPU. It works very well outside the CPU fan runs constantly at 100%

  You have installed a stronger CPU that is faster and produces more heat dissipation.
  It s nothing unusual that your fan runs faster.
  The cooling module must run more quickly to make sure that the CPU would be cooled properly.

• Tecra S11 - CPU fan is high speed

  Hello

  We have a problem with nine Tecra S11 / Windows 7 64-bit. The CPU fan is noisy high speed during ignition and start Windows. No change after logon. Speed remains unchanged up to go to the sleep mode once. After waking up, everything is OK.

  For me, it seems to be a problem with the firmware (BIOS). Update V1.70 but no change. We have same problem with the S11.

  Any ideas?

  Cordially Stevep

  Hi Stevep_1,

  Have you tested different cooling options in Windows power management? Check it for each profile, and then select battery optimized cooling.

  It work?

• Pro M30 satellite cpu fan works not

  on two occasions, I replaced a system on a satellite pro m30 card so that the cpu cooling fan no longer works. This is the case even after recovering the OS from the disk.

  is there any other known this.

  I talked to others who say that I need to improve the DMI

  any help please

  Hello

  Well, I put t know if the DMI update will solve it, but as far as I know the service partner should upgrade the DMI. After the replacement of the motherboard it is also important to start the diagnostic program and special test, because without this procedure, the CPU can t works with a maximum return. This can be done by the service partner. The update of the BIOS is also a possibility

• Satellite L30 - 10Y - upgrade successful but CPU fan is running

  Hi ppl,
  This post is more than a FYI post.

  I gave myself a defective Aspire 5610 and decided to whip the CPU out of it and put it in my Toshiba Satellite L30 and it works! CPU of the Satellite is a series of Intel Celeron M @ 1.87 Ghz, while the Acer processor is an Intel T2300 Centrino Duo 1.66 GHz. So my Satellite is now slightly faster, but added to it's 2 GB of RAM and a hard drive upgraded to 320 GB under Windows 7 Ultimate. While its still not a game machine, it creaks all the numbers that I throw at it!
  Hope this helps someone.

  I noticed that the fan runs almost constantly, suggestions?

  Concerning
  Markkyboy

  Hey,.

  Thanks for this very interesting article! It of Nice to hear this new CPU works fine, but I have to say there is no guarantee for this, but you have chance ;)
  Update CPU's official not taken in charge, but in some cases, it may work, depending on the motherboard, BIOS and CPU.

  In any case, I think the fan runs almost constantly because the newer and more powerful CPU producing much more heat and it must be cooled cooling system that is designed for your older CPU.
  All you can do is to clean the cooling system, but I think you have already done this during the exchange of CPU and use of grease thermal correct amount.

• 850 - 009na M1Z34EA #ABU: CPU fan for the 850-009na feel like Phoenix does not turn down after the power - on self test unless the BIOS is entered

  Hello

  I have posted responses to other posts on this topic, but thought I'd start a new thread to gather my conclusions. I'm sorry for a trial

  This PC is virtually brand new (only a few weeks now) and otherwise perform exceptionally.

  Basically, if the machine is disconnected from the power grid (i.e. the power is off at the plug or the power cord removed), when the machine is supplied then the CPU fan turns over 2000 rpm and stays there. All the other PC that I do this too, but the fan will slow down after turning upward. I know that this is done as part of the POST to check that the fan is running.

  If I go into any installation of seed, start-up or BIOS for example (i.e. by pressing ESC or F10 etc.), the fan will slow down immediately up to 700 rpm. It will stay like that until the next time the machine is started against the cold. If I shut down the PC - watch or stop - but do not cut the power supply, then the next time the machine is started, the fan is still about 700 rpm. It is not to turn up to 2 k + RPM when lit.

  As soon as I unplug, then the next time the PC boots, it will turn to the top and I have to repeat steps - off, boot, enter the BIOS, exit and continue. It is something to do with the cold start.

  Note that I don't have to do anything in the start menu - I for example go to the BIOS settings, exit without saving the changes, and the fan will still slow. It's going in the boot sector that slows down the fan.

  When the PC started out-of-the-box, I opted for the upgrade to Windows 10 during installation. I have read in various places that people had experienced after the upgrade, so I reset the machine to factory settings (Win 8.1) and have not upgraded, but the problem persisted. However convinces me that Windows 10 has been removed completely, as when I went to restore the backup image (i.e. dating back to what I had before the factory reset) there are references to 10 Windows (for example, it says 'Continue to Windows 10' as well as various food options). I do not understand UEFI so I don't know if that was involved.

  I tried to change the power plan options "Processor power management-> cooling system strategy" on the liabilities side, but no joy there.

  I think that the fan and sensors work, based on the findings below. These readings of temp and fan are taken from AIDA64

  After starting cold (current was cut, without entering the BIOS), machine runs dry without load

  

  Exactly the same thing--starting in cold, but go in the BIOS, do nothing and continue. Once again, no load

  

  This is after power off and resarting, but to let the PC network

  

  After the above, I used Prime95 to put the CPU support (use of 95-100%), and after an hour, the readings are:

  

  Note that even so, the fan was not particularly strong, but it's at 2222 rpm as in the first reading.

  If I play at 4K (the whole point of the PC ) the CPU so far got very warm, the GPU is but his fan turns up as planned.

  In conclusion, it seems that the POST has a problem because it does not slow down the fan after the test.

  I can live with let the machine always plugged into the sector (for example, most of the time) and I guess that's what most people do, but I would like to know what the problem is (for example if it's really something 10 Windows, or a bug in the BIOS/UEFI)

  Thank you very much!

  John

  Explain you a lot of people who maybe have returned their system immediately because of this? Others might judge normal sound. Not irritable average is not coming here to complain. Others might judge her so little. They simply don't like. You will never convince me that is not a BIOS problem. As the problem resolves itself when you enter manually each time. It can be reproduced every time.

• Tecra 9100 stopped after one hour of work

  I bought a Tecra 9100 and he stopped after an hour of work or less like frozen.
  Using the keyboard or the mouse to restart did not work.
  I have to use the power button to shut down and restart after stop down.
  I tried to reinstall windows xp and change the ram, but still the same problem.

  Thank you very much!!

  Hello

  How long have you used the laptop?
  Eventually the temperature inside the laptop could be responsible for these issues of freezing. A similar problem occurred on my laptop. He frisottés due to overheating.
  I just cleaned the fans and cooling grids modules with the vacuum cleaner and the problem disappeared.

  I think you should also check the cooling modules and try to clean it carefully.

• 500-210qe Pavilion: Pavilion 500-210qe: cpu fan not detected after update BIOS

  Pavilion 500-210qe started showing ' 511: cpu fan not detected; F1 = boot' message.  I checked the BIOS rev level and set to upgrade to the latest (80.13 FRIEND) but the problem persists.

  At startup, the cpu fan is not running, but after pressing F1.  Please notify.

  From the least expensive option, replace the cpu fan (which comes with the heat sink) has solved the problem.