Tecra A9: Windows does not start after you turn off multiprocessor in BIOS

Similar Questions

• AT200-100 does not start after the turn off

  Hi @ all,

  I have a problem with my AT200-100 (bought @February 2012 in Hong Kong).
  In recent days, trying to find a solution.
  After using I turned off the tablet. When I first it overnight, it just goes to the Welcome screen "Toshiba."... "and then comes the animation of watering and then - nothing. Screen is black and start this new animation - without Toshiba's ' welcome' screen.
  After some time of the animation, the same thing happens again and again and again...

  I tried to leave it on until there is no more power then I loaded the Tablet and tried again to start. Same situation again.
  Could someone tell me what to do?
  Thanks for your help...

  Hello

  Looks like that Android has been corrupted, have you tried entry recovery mode and do a factory reset?

• game does not load after you turn off the flash of pepper

  I play a wgt golf game, the game said if I were haveng problems turn off the flash of pepper and I did it and now the game does not load happens to 77% it stops there. Ive been trying to find how to activate the pepper flash then maybe I can play the game but no luck. I can play the game on my other computer without any problem, please help

  Flash Player Help. Installation problems | Mac OS

  Flash Player Help. Installation problems | Windows

  Mylenium

• BootCamp Windows does not start after you have enabled disk encryption

  Hello everyone, I am in a desperate situation and I need your help. Here is my sitatuaion.

  I have 13-inch MacBook Pro (early 2011). I put an SSD inside as my main drive and I also put an extra drive (HDD) in the optibay instead of my drive superdrive. The structure, I had was this:

  (1) my entire SSD was my OS X disk.

  2 my HDD optibay had three partitions: partition backup Time Machine, a) b) Extra partition (for stuff like media), c) Windows partition with Windows 7 installed.

  Had that Setup for a long time and everything worked very well, my SSD has been saved on the Time Machine partition on the HARD drive in my optibay.

  Then, I decided to turn on the File Vault 2. First of all I did for the SSD with my OS X on it. Everything went well and I could always start my Windows 7. Then, I decided to encrypt my Time Machine backup (because what's the point to encrypt the main system disk if you do not encrypt the backup as well?) -Here too everything went well.

  In other words, until I needed to start Windows. I have restarted my Mac, hold down option, the picker contraption came, but there was no windows to the choice. I came once before (but), so I knew I could always start in it.

  I jumped into my USB thumbdrive with fairing on it, he chose and he gave my start on the Windows partition option. But this time it did not work, I got an error message saying my there is no bootable device or something like that.

  I have confidence in turning the things of encryption for the partition of Time Machine (which is on the same HDD as my Windows partition) screwed disc here.

  The only question is: can I fix, start Windows, without having to install it from scratch? What I want is to have encryption enabled for both drive my main SSD where I have my OS X installed AND the partition of Time Machine that is on the disk in the optibay HARD and also have a Windows partition on it, but still be able to start Windows.

  I am running 10.11.13 El Capitan.

  Can you help me somehow? Here is my list of cs diskutil:

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 128,0 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_CoreStorage Macintosh 127,2 disk0s2 GB SSD

  3: disk0s3 Apple_Boot Recovery 650.0 MB HD

  / dev/disk1 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 500,1 disk1

  1: EFI EFI 209.7 MB disk1s1

  2: Apple_CoreStorage Time Machine 150.0 GB disk1s2

  3: disk1s3 Apple_Boot Boot OS X 134,2 MB

  4: Apple_HFS Extra 300.0 GB disk1s4

  5: Microsoft Windows 49.5 GB disk1s5 data base

  / dev/disk2 (internal, virtual):

  #: NAME SIZE TYPE IDENTIFIER

  0: Apple_HFS Macintosh SSD 2 GB + 126.8

  Logical volume on disk0s2

  406F3A62-89AE-4F91-BEEF-B8CE0B16C8EF

  Unlocked encrypted

  / dev/disk4 (internal, virtual):

  #: NAME SIZE TYPE IDENTIFIER

  0: Apple_HFS Time Machine disk4 GB + 149.6

  Logical volume on disk1s2

  0567D276-3738-4776-9CC5-B69F922B0A0C

  Unlocked encrypted

  Your problem is not related to FileVault2. Your question should have begun when additional Apple_HFS was created. Please after the release of

  sudo fdisk/dev/disk1

  If you have a problem with your Mac, you can potentially lose the SSD and backup TM. It is not an optimal configuration. A TM must be physically separated from your Mac, so you can restore the TM backup to a new Mac, if necessary.

  Also, since you removed the optical drive, re - install Windows on your 2011 model is a very rough road to travel.

• Windows does not start after you use vaio recovery

  I tried to reset my computer to factory settings and programs. I used the for Vaio recovery tool do. During the course of my computer restarted as it should. But as Windows was returning back I get an error of "Windows Boot Manager" say a file called ntoskrnl.exe was missing or corrupt with status 0xc00000e9 upstairs he provided a way to fix: cannot start Windows. A recent hardware or software change might be the cause for the problem:

  1. Insert your windows installation DVD and restart.

  2. choose the language settings, click Next

  3. click on repair your computer

  After step 3, the repair tool said that it could not solve my problem.

  I tried to redo the recovery twice for nothing doesn't.

  I tried to use the memory diagnostics.

  I tried to change the default BIOS settings.

  I tried to use the chkdsk command in the console installation disc

  I don't have a backup disk.

  You could try System Restore option under the recovery tool if startup repair option has not resolved the problem. After the execution of the Image recovery system on your VAIO computer and you still have the same issue, then you may need the recovery disc. If you have any errors after the diagnostic equipment, then the recovery partition was damaged already.  You can buy the recovery disc for your computer of Sony parts and accessories or parts distributor authorized Sony.

  If my post answered your question, please click "accept as a Solution.

• The browser does not start after you have turned off and turned on the computer

  The browser does not start after you have turned off and turned on the computer. I tried to remove the program entirely (as well as personal preferences), to create a new account, install a different browser versions. All this has not helped. (I have Windows 7). Help, please! Every day I have to reinstall Firefox!

  Hello Nastena, try a clean reinstall, some Firefox issues can be resolved by performing a clean reinstall. This means that you Remove Firefox program files and then reinstall Firefox. Please follow these steps:

  Note: You can print these steps or consult them in another browser.

  1. Download the latest version of Firefox from http://www.mozilla.org office and save the installer to your computer.
  2. Once the download is complete, close all Firefox Windows (click on quit in the file menu or Firefox).
  3. Remove the Firefox installation folder, which is located in one of these locations, by default:
     • Windows:
       • C:\Program Files\Mozilla Firefox
       • C:\Program Files (x 86) \Mozilla Firefox
     • Mac: Delete Firefox in the Applications folder.
     • Linux: If you have installed Firefox with the distribution-based package manager, you must use the same way to uninstall: see Install Firefox on Linux. If you have downloaded and installed the binary package from the Firefox download page, simply remove the folder firefox in your home directory.
  4. Now, go ahead and reinstall Firefox:
     1. Double-click on the downloaded Setup file and go through the steps in the installation wizard.
     2. Once the wizard is completed, click to open Firefox directly after clicking the Finish button.

  Please report back to see if this helped you!

  • Also check if your antivirus or other access security software (firewall, antispyware etc.) blocks firefox.

  Thank you

• Windows does not start after the update...

  Hope someone can help with this,

  I just installed the update sp1 for my computer for Windows Vista Premium Home dir all installed with no problems, but when I restarted my pc, Windows wouldn't start. The only thing that is on display is a black screen with Windows Error Recovery on top, then he said "Windows does not start. A recent hardware or software change might be the cause. I tried to restart it in different ways, but nothing. Then he said: I have to insert my OS drive to try to fix, but that's not even start. Everyone knows about this problem? This has happened right after that I installed the update...

  L.Butler,
  Are you able to boot from your Vista DVD or recovery partion and run the Startup Repair tool?  If you do not have a Vista disc so make sure that your computer is configured to boot from the CD drive before booting from the hard drive.  Once you start with support for Vista select the "Repair your computer" option and first run "Startup Repair".  If that is not correct the problem then boot with Vista support and select the option "System Restore" and choose a date prior to the update install.
  Once you are able to boot normally again, then I suggest that you are looking for virus\malware.  SP1 was released in April 2008.  So if you install earlier means there may be other problems on your system.  If you have a backup of your current personal data then I recommend to do a clean restore to install\factory.  Then immediately install antivirus software, and then do all Windows updates before installing other software. Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Help my pc does not start after you have uninstalled the video driver

  Please help my pc usually start more after I uninstall my nvidia driver mx/mx 400 with YourUninstaller I try to use this option to uninstall my driver in super mode then prompt YourUninstaller and asked "do you want to restart your computer now" then I click Yes but YourUninstaller software now on the race because the YourUninstaller has finished remove the registry left behind by uninstalling normal after that there is no register found after scanned. Then I click Next, then I closed this request. Then I restart my computer manually but blocked windows then I wait 5 or 10 minutes, but do not restart Windows. I turn off my APR, then I turn on my pc then windows does not start. I try to reformat but it's the same story that windows does not start. I try to remove the cmos battery hoping it will solve then it works. But the problem is that I insert my bootable cd, it runs automatically even I don't not press a key on the keyboard, the process to continue installing windows, it sounds I can not install my windows correctly. When he restrart the process goes again to load all the drivers everywhere why did this happen? Is there something wrong with my HARD drive once I used YourUninstaller?

  RAM of a problem with you, I guess. Remove the RAM and clean including the slot of the motherboard.

  http://www.computerhope.com/beep.htm

  If this post answers your question, click mark as answer .

• IdeaPad Y530: windows does not start after that laptop went to sleep mode.

  Hello

  More great frustration in my life have laptop brand new, this for me.

  After that the laptop goes into mode 'sleep', I'm not able to go back to Windows. All light are there and watch as usual, but there is no Lenovo Welcome logo or any other sign of normal behavior. I can turn it off by holding the button market / stop, but when I turn back the problem is still there. Windows does not start.

  I was able to go back to Windows that day after leaving just laptop without any power and battery.

  I called Lenovo and they suggested to disable the standby modes use put into hibernation. I did it. When the screen saver started, something went wrong, computer got froze and I had to restart, but then again, black screen and no reaction.

  Anyone have any ideas?

  Thanks for the reply.

  That's what I end up doing. OnKeyrecover does not work either so what spoke on the phone with Lenovo. Then he is gone now for repair.

• Portege R830 - Windows does not start after I have install Comodo Firewall

  Good afternoon

  I bought today a Portege R830, and after the Windows configuration, the first program that I installed was the popular free Comodo Firewall. After that I restarted, Windows 7 unbootable. It would be stuck on the user login screen and I know it's a problem with the firewall because if I do a system restore to the restore point created by Setup of firewall, windows restarts.

  So I ask if there is any inconsistency between the firewall and software on the Toshiba. A that someone already had this problem? I tried to solve this problem throughout the day with no results. I even re-installed Windows 7 using the Toshiba Recovery and the problem persists. I really like the Comodo and I want this firewall on my laptop, but Windows does not just start!

  Any help would be apreciated.

  Hi jillefsky,.

  Have you disabled the Windows Firewall before you start with the installation of Comodo Firewall? As far as I know, Portege R830 is delivered with preinstalled McAfee security software and you must remove this program before you install other security tools.

  Generally this has nothing to do with Toshiba and it s advisable to contact Comodo directly. They may know about this so they can give you a proper answer.

  But I put t understand why this program is so important to you. Windows already has an internal firewall so that these programs are not necessary in my opinion. Just install a good antivirus like AntiVir and enable the automatic updates of Windows. All that s!

• Windows does not start after Windows update.

  Original title: udate Windows vista problems

  I have dell dimension e520, Windows Vista home Basic, 32-bit SP 2, and in January, I upgraded RAM to 4 GB to 1 GB. McAfee security on the computer. The system worked until the last updated (March 2012).  The computer does not start correctly after March 2012 update and System Restore restores to February 21 implemented to date.  The computer will then automatically install the updates again and restart, after which the computer will not start up again (an annoying loop).  I also lose saved data after the system recovery sets return date.  I tried Microsoft Fixit, which did not help.  Thanks for your help. Hurry LOL available updates.

  PS computer says 'patch blocking windows to start.  Some updates successfully installed previously, but on the next time you download windows updates, that try to download updates and others have "failed."  Sorry for the confusion but I'm rushing and I try to include all the symptoms, I don't see dealing with the problem I have.

  I had to take it to get fixed, thanks to the effort.  The person fixing said he ran a few cleaning tools and which appeared to fix.

• Tecra M2 - Windows does not start correctly

  My computer recently crashed and I suspect that this has affected the BIOS. I believe that the cause was a hardware problem or Trojan horse, as when the computer is restarted it will fail to load the BIOS at all 9/10 of the time. I found the Toshiba Tecra M2 BIOS V1.50 and it says it takes V0.06.00 of Modules common Toshiba, which was more difficult to find and could not solve the problem. Installation of an updated BIOS failure as well.

  For now, Windows loads up with lines running down the screen; When the windows startup failed and by displaying the "Windows did not start successfully screen', some letters are altered," soory for you e afconvenaence, but Wandows dad ngt star ^ correctlq'. "

  A new installation of Windows has failed to achieve anything more. If anyone has an idea how to solve this problem, it would be greatly appreciated.

  Hello!

  I think that it is a problem of material caused by the BIOS or the graphics card.

  However, it s not able to change the graphics card because it s soldered onto the system board.

  Perhaps an ASP can help you and do a downgrade from the BIOS, but I think that you need a new mainboard.

  Good bye

• Satellite Pro A60 EN does not start after you have used the recovery CD - isapnp.sys missing or damaged

  Help am stuck with it.

  Necessary to perform a recovery on the laptop and used the recovery CD 2 they seem to work OK. No error during installation, but after that they finished and it restarts didn't get the following message.

  Windows could not start because the following file is missing or corrupt:
  System32\drivers\isapnp.sys

  You can attempt to repair this file... etc but I don't have any original installation CD all have is the recovery for the Toshiba.

  I have a setup of Windows XP for the PC disk, but when I try to run which, but it starts just the configuration. Setup is loading files and after the kernel debugger get error

  "File ntkrnlmp.exe could not be loaded.
  The error code is 4, sometimes it's 7.

  I tried to delete and recreate and formatting partitions, so I can see and I can copy a file to the C: drive

  So any suggestions as to what wrong here

  Thank you very much

  I put t know if this Microsoft Knowledge base article would be useful for you, but you should check it out.

  [You receive a "Windows didn't start because the following file is missing or corrupt: Isapnp.sys" error message at startup | http://support.microsoft.com/kb/315311]

  Microsoft has a solution, and I would like to know if you can solve this problem by following the steps of the solution described in the article.

  Feedback would be much appreciated

• Windows does not start after update

  Stop PC last night and let it install 3 critical updates at shutdown. On the PC this morning, it won't start. Repair of the system indicates it cannot automatically repair...

  Restores the auto system restore point before the decommissioning, and it now boots normally...

  Then, Mr. Gates, who, following updates kills my PC? :::

  Update security for Windows 7 (KB2419640)

  Download size: 857 kb

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  A security issue has been identified that could allow an unauthenticated remote attacker to compromise your system and take control. You can protect your system by installing this update from Microsoft. After you install this update, you may have to restart your system.

  More information:
  http://go.Microsoft.com/fwlink/?LinkId=204803

  Help and Support:
  http://support.Microsoft.com

  Update for Windows 7 (KB2454826)

  Download size: 4.7 MB

  You may have to restart your computer for this update is taken into account.

  Update type: recommended

  This is a reliability update. Install this update to enable a set of performance and features updated graphics, Media Foundation and the XPS components on Windows 7 systems.  After you install this item, you may have to restart your computer.

  More information:
  http://support.Microsoft.com/kb/2454826

  Help and Support:
  http://support.Microsoft.com

  Update for Windows 7 (KB976902)

  Download size: 4. 3 MB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  Install this update to enable future updates to install successfully on all editions of Windows 7 or Windows Server 2008 R2. This update may be required before you can install the selected future updates. After you have installed this item, it cannot be deleted.

  More information:
  http://support.Microsoft.com/kb/976902

  Help and Support:
  http://support.Microsoft.com

  Windows malicious software removal tool - January 2011 (KB890830)

  Download size: 999 KB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  After the download, this tool runs once to search your computer infections by specific, prevalent malicious software (including Blaster, Sasser, and Mydoom) and remove infections found. If an infection is detected, the tool displays a status report the next time that you start your computer. A new version of the tool will be offered each month. If you want to manually run the tool on your computer, you can download a copy from Microsoft Download Center, or you can run a version online from microsoft.com. This tool is not a replacement for an antivirus product. To help protect your computer, you must use an antivirus product.

  More information:
  http://go.Microsoft.com/fwlink/?LinkId=39987

  Help and Support:
  http://support.Microsoft.com

  This thread seems to describe the problem you are experiencing:

  Windows 7 - KB2454826 fails and only recover after reboot

• SRM does not start after you have moved the database

  We're under 4.1 SRM and moved its sql database to a new server sql (new server sql a different host name).  We moved successfully to the virtual center & Manager Update bases sql data, but after moving srm4.1 database, the srm service does not start...

  so far, I uninstalled SRM (DO NOT remove the SRM database)... After uninstalling SRM, I rebooted the server.  Then I have re-directed the SRM installation and started going through the installation of MRS... After pointing the SRM installed on the server vcenter, port 80, and pointing to an existing sql database, etc., I get a thumbnail of certificate message and a prompt on the creation of a new certificate, which i say 'yes' to... Installation continued on and arrived at the end when it says "create certificate"... then does not say "cannot install the certificate...". Database error has occurred. "At this point, the installation failed

  Any ideas on how to remove the old certificate or work around this error?

  Thank you

  I think the error message is misleading in this case and the problem is not related to the certificate.

  I still think that it is permission DB / configuration number.

  Following links may be useful:

  http://communities.VMware.com/thread/212157

  http:// http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=1015883

  Michael.