Tecra M2 PTM20E Wireless problem.

Hey

I just bought this laptop that was used I installed very different drivers for the wireless, but none of them work. I also have a problem with the battery.

I think there is a problem with the network card if yes is it difficult to replace?
Thanks for any answers I've attached screenshots here below

http://Tinypic.com/r/246883k/6 - network driver cannot click anything that nothing works

http://i45.Tinypic.com/fdesya.jpg - problem battery sound in a foreign language, but it means windows can't find a driver for battery

http://Tinypic.com/r/2vtnm7a/6 - no internet connection that you can see that the window is empty

http://i49.Tinypic.com/bis86c.jpg - home edition everest showing the map as a one intelPro.

Sorry for the foreign language: P

One of the photos shows the network cards and it seems that your Tecra supports processors Intel 2200 802.11 B/G WLan card

Go to Device Manager and check if the WLan Intel 2200 card is recognized.

If it s not, install the driver WLan Intel (Intel PRO/Wireless 2200/2915) which can be found here:
http://APS.toshiba-tro.de/WLAN/?page=downloads

the first photo shows only Intel ProSet is just and only the tool for configuring Intel Wlan driver and NOT so possibly the driver WLan is missing.

Tags: Toshiba

Similar Questions

  • Tecra M2 PTM20E - 598 Mhz processor speed

    Hello
    I have no model tecra M2. PTM20E-4MP1N-GR.
    One of the problems was appear:
    Speed of the processor is clocked at 1.6 GHz, but when I check in the Windows system properties, the speed is 598 Mhz, and the system is very slow.
    How to change on the rise?

    Tab CPU are not displayed in SWsetup.
    It is also not possible to change the standard configuration after reboot.

    Help, please. :)

    Best regards
    DarJan

    Hmm. very strange

    Did you change the motherboard or you did a hardware upgrade?

    As far as I know, such behavior can occurs after replacing the CPU or the motherboard.
    After the replacement of the microcode must be written again.
    If the technician forgets the microcode update then the CPU goes only to ~ 600 Mhz.

    I'd appreciate feedback.

  • Tecra M2 PTM20E 'network controller' and pilots 'base system device '.

    Hello.

    I can't find drivers "network controller" and "base system device" Please tell me the exact name of the driver and the place for these drivers to download, I already checked under tecra M2 section but can't find any, please help.

    My operating system is windows xp

    Not for my machine model is toshiba tecra M2 PTM20E

    If I go to system information then I see problem thing it shows

    PCI\VEN_8086 & DEV_1043 & subsys

    Concerning

    Hi search this forum - tecra m2 - to 'base' or "yellow exclamation" and see my post that will sort you if all goes well.
    I don't know how to tie a link in this forum for you take directly to her.
    Posted by jarviei.

  • On Tecra A9 BIOS password problem

    My computer laptop Toshiba Tecra A9 have a problem with the BIOS password and I was wondering if you could provide me the password because I can't access anything whatsoever, without it

    BIOS password is very important security feature and these issues cannot be clarified on public forum.
    Any problems with the BIOS password must be clarified with the Toshiba service provider.
    If your laptop is blocked by password and you cannot access, please contact the nearest service Toshiba and they can remove it for you.

  • WAG320N wireless problems

    I am having major problems with my Linksys WAG320N. Hoping someone here can help as I am quite clueless when it comes to networking.

    Without changing the settings, the other day that my Macbook Pro could not connect and he kept saying 'timeout '. From that point my iPhone also refused to sign, although access to the internet on my MBP viaethernet was fine.

    I did a hard reset according to the instructions of this forum, and then re-configured with the installation CD. The router wireless light was turned on but my MBP did not see the network. Finally, I managed to connect after I restarted my laptop and enjoyed every 10 minutes without internet connectivity before wireless problem network come fall and now does not appear in my list of networks once again, even if the wireless light is still on.

    Ethernet connection still works, but not via the wireless.

    I restarted my laptop and the router and tried switching channels on the router, all to nothing done. Very confused and frustrated!

    Someone at - it suggestions? Thanks in advance for any help.

    What is the wireless settings you have set up on your router (SSID, channel and security mode)?

    Connect to your router configuration page and click on the Wireless tab and click on the "Advance Wireless Settings" sub-tab and under change 75 beacon interval, change the Fragmentation threshold to 2304, change the RTS threshold to 2304 and click on save settings...

    Now let's see if you can locate your wireless network and try to connect...

  • T40 2374-PU3 wireless problems

    T40 2374-PU3 Wireless problems - I tried every driver and followed instructions to install several times.  I was able to install it successfully in the past (about a year), but do not remember with the version of the driver that I used.  Using WinXP SP2 - just installed.

    Help, please!

    Thank you!

    Welcome to the forum!

    Here is your wireless driver:

    http://www-307.IBM.com/PC/support/site.WSS/document.do?lndocid=MIGR-42683

    After uploading, be sure to check out according to the instructions on the download page.

    I hope this helps.

  • S10 - 3T wireless problem

    My rig to receive yesterday and fought wireless problems.  Thought, he was my network for some time and found if I close the 3 t of the network works fine.

    The 3 t at this point works well on the network but sometimes slow.  However any TIME that I try to download a file, it works as usual for a while then just dies.

    Stop downloading and it is surfing.  It seems also to kill or slow down the network to a crawl at the same time.

    I tried to update the drivers in Device Manager and it says they are the best already.

    Any thoughts?

    Thank you for your understanding.

    The ends of the ongoing saga I think.

    I went to Burger King this morning and connected to their hot spot and the thing that worked great - downloaded a large file on site.

    Lenovo, I called and they told me to uninstall the software Lenovo 5 ready.  I did and rebooted and it worked fine and still seems to work very well ;-)  They said that it causes conflicts.

    Worked on my unit anyway.  This happens on a platform of Asus here one year, their uninstalled software and it worked fine.

  • Tecra M2 and wireless network - signal strength problem

    Need advice buying wireless kit.

    I have a DSL phone line connection and I am currently using a Speedtouch USB modem connected to my workstation down.

    I have a laptop Toshiba Tecra M2 with construction of wireless support. I want to be able to share the internet connection which comes in the workstation down. I guess that my options for the workstation are to use a DSL wireless modem to share the internet connection or to use a PCI card in my computer. I tried them both.

    I first tried to set up an infra mode network with the laptop using a LinksysWAG54G which was connected to the telephone line and a computer. But the problem with that I was t couldn't do accept the subnet mask that my ISP (Lixxus) provided 255.255.255.255 (PPoA). This modem has all the masks of SN in a dropdown list, but mine isn't in this list. I returned this modem.

    I tried then set up an adhoc network purchase buy a PCI Wireless card for my desktop, and internet connection sharing etc. on the workstation. However, while it worked, and I could see the desktop of my laptop, the problem has been the wireless range. The signal disappear when I wore the laptop in the back room on the first floor. It would have been a distance of 10 meters in a straight line between the laptop and desktop. There are walls two bricks and a floor between the two machines. It seemed hopeless, so I sent the PCI card.

    I'm not sure what to try next.

    Any suggestions that I could try next?

    Suggested hardware?

    Signal strength - could the problem be that the antenna in portable insufficient Tosh - it too small?

    Hello

    I have the same situation at home. The best solution for this is to use the wireless router. Here you have the possibility to connect several computers desktop or laptop. In this case the configuration of wireless connection is very easy and it works fine. I also use it at home and in front of my house with no problems.

  • Tecra M3 & Port Replicator III wireless problem

    I just bought a Tecra M3 and a port replicator III. When undocked the M3 connects to my WiFi without problem and remains connected. Once anchored it continues to have problems connecting, despite full status of the receiver and after connection bar / disconnect for a while he just gives up and says unable to connect. If I disconnect then it can connect ok. Someone at - it ideas. It can see the network fails to connect properly.

    Hello

    Very simple to solve, you must upgrade the driver Intel Wireless 2200 b/g Intel 9.0.2.25 card or higher.

    Good luck

  • Tecra A9 - wireless problem

    After that I installed XP on my Tecra, the wireless seems to respond slowly. After I turned on my laptop, the Wireless 'most of the time' is directly connected to the network (even though) I have already implemented etc preferred networks. And many times it says "no wireless networks in range" when my wireless router sits beside my laptop... my other works laptop fine tho...

    I try to reinstall the driver of Toshiba Europe pilots, but it doesn't seem to change anything...
    It's my router or my laptop (but the bluetooth works fine)?

    Have you checked the BIOS updates recently? Where the wire is disconnected very often, BIOS and driver update allows in most cases.
    Windows XP service pack 2 is installed, and all necessary updates have been made.

    The same thing I had with my desktop PC with the wireless device. Router was next to my material, but I've always had these disconnections and updating of drivers and BIOS helped.

    Can you try this, oh and check if no device interfere is close.

  • Tecra 9100 - no wireless connection

    Can anyone help please?

    The wireless in the toolbar icon has a red x and will not let me connect even though I see my router.
    Can someone tell me how to solve this problem? I have Tecra 9100 with Windows XP SP3.
    Thank you

    Hello

    The icon in the toolbar with a red cross?

    Well buddy, have you checked if the WLan card is properly recognized in Device Manager?
    Usually a first step to clarify if the wireless card is ok or if something breaks down.
    In the device-> network card Manager, you should see the wireless network card.
    If there is a yellow exclamation point, then try to update the WLan driver.

    If the driver has been installed correctly and there is no yellow exclamation mark then the next step would be checking the settings of network connections.

    Check if the wireless network connection is enabled (Start button-> settings-> network connection)

    Check it out!

  • Broadband Tecra R10 - 10J 3G problem

    I have a new Toshiba Tecra R10 - 10J

    I can't operate the 3G.
    I put my 3 G SIM card in the slot (behind the battery)

    High-speed 3G Toshiba F3507G appears three times in the device (network card, modem and com port) Manager

    However, when I start the Wireless Manager, the 3G device is not recognized!

    Thanks for your help

    Concerning

    Thanks for this second info
    In many cases the computer reboot laptop new solves many strange problems ;)

  • Tecra A4 fluctuating wireless.

    I have a new Tecra A4 and a BT Voyager 2100 router.

    I had the router for some time and never had a problem using it with any products before, I have other laptops that connect to it and can use it without any problem.

    However my new A4 seems to have 'questions' to a clean boot, with no applications running, a ping to the router can fluctuate from 1 ms to expired and all points between. The speed of the network can also fluctuate from 54 Mbit/s to 1 Mbit/s and also often loses the connection.

    As I say, other devices with the same network configuration do not have this problem and the distance between the router doesn't seem to be a factor either, as happens in the same way in any room of the House. I've removed the other sources of interference, I tried to change the network type / speed / channel and the problem persists. Im not sure what else to try, can someone point me in the right direction please?

    Hello

    Is a wireless card disabled when you use Bluetooth? You can turn it off using the FN + F8 key combination. Disable the wireless connection while using Bluetooth. Maybe it helps.

  • BOUNCING Tecra M11 - 11K wireless signal

    Hi all

    I was wondering if anyone has had problems with a Tecra M11 - 11K running on the latest service pack of Windows 7 Professional 64 bit.

    In it, the wireless tends to disconnect sporadically, no matter how clean the signal is WAP, or what type of encryption. All the other machines work very well and it has the same behavior when using hotspots public or closed...

    We also tried to use the latest drivers provided by Intel, nothing helps.
    The machine also has a system to install.

    Clues or tips would be greatly appreciated.

    Hello

    Have you tried to deactivate the energy saving function?
    Windows 7 power management offers various options in order to save the battery.

    If this may affect the Wlan functionality.
    Please check the Windows 7 power management and disable the Wlan to save energy.

    Also you can go to-Wlan card-> Advanced tab > Device Manager and could check the available options.
    I can't tell exactly what options are available, because it depends on the Wlan card.

  • No noise in Tecra M2 (PTM20E-01MX2)

    Hello

    I just reinstalled windows for the second time, and I still get the same error when I try to install the soundmax software and driver. The device driver was not found. And it's true that it can not detect the sound card on my Tecra M2. In the bios the device SD is enabled, so it should be ok. My BIOS version is 1.50, I ve download 1.60 version but when I try to install says it is not compatible with my laptop, I ve already checked and I ve download version PTM20E.
    If the sound card is damaged? Is there something more, what can I do?

    Best regards

    Pedro Sousa ML

    Hello Pedro

    At first I must say that your ad is quite confusing. If I understand you right in two sentences, trying to describe 3 different problems:
    -1. Audio driver installation
    -2. Features of SD slot and
    -3. Update BIOS
    Am I right about that?

    Before starting to discuss can you please tell me what version of Windows you have installed on your laptop Tecra?

Maybe you are looking for

  • I accidentally deleted my folder "Downloads" from the dock. How can I get it back?

    Hello I accidentally deleted my "Downloads" folder / icon in the dock and then loses in the sidebar of 'Finder '. Grateful for advice on how to pop it back. It is ElCapitan of iMac. Thank you.

  • Satellite L670-11R - black screen

    Hello! My mother's cell phone has a problem since yesterday. Its a L670-11R. When you start, the screen remains black. I tried different things, expectation, remove the battery, press F8 and also tried another monitor.Nothing has worked. Any ideas? W

  • Device Manager - unknown device + Hig Defintion Audio Device (Point of Exclamation)

    Hello I hope that someone can help you. The hard drive on my laptop of HP ENVY TS 15 (product number: E3S19UA #ABA) out crapped and I reinstalled Windows Enterprise 8.1. I downloaded and installed all the drivers from the HP website. When I look at t

  • What is smax4pnp.exe?

    What is smax4pnp.exe? He takes over at the start.

  • Windows RE image is not found

    Hi, I have an Aspire V3 - 772G. I can't create a recovery drive more. I ran reagentc.exe in command prompt and it points to the correct location of recovery, but Windows RE is disabled and for some reason I can't reactivate it. Someone knows how to f