Tecra M3 - when the motorized screen is completely black

Similar Questions

• When the computor screen projector turns black after hitting fn F8 and screen projector flashes

  When you use a projector my computor screen turns black after hitting the fn F8 and screen projector flashes in and out, how to fix?

  It never worked correctly?
  If Yes
  Did you change since then?
  You can use system restore to revert to this point?
  If not.
  You try to play on the computer and the projector at the same time? What happens if you just play through the projector?
  Try to update your driver for graphics card via the laptop manufacturers site or the manufacturer of the graphics card if a desktop computer, do not use windows update.
  Update DirectX
  Reduce the graphics acceleration of the map - http://www.myvideoproblems.com/Tutorials/HowDoITurnOffAcceleration.htm
  Disable other programs running.

• The button on my lockscreen does not work on my phone. Recently, my screen went completely black. I can turn on siri. How can I get my screen to turn back?

  My 5 IPhone lockscreen button does not work so I use touch help to the screen power off and screenshot. As I was using my phone my screen went completely black. I tried to plug it into a charger and call but the screen still won't turn. My phone vibrates when I call and I can't turn on siri. I tried to search the Internet on how to re-enable it. Everything I've seen involves using the screen lock button but obviously I can not use it. How do I reactivate it?

  Hello tumbler3100,

  Thank you for using communities Support from Apple!

  I understand that your iPhone screen is returned while you were using it and the on/standby button does more either. Because your iPhone is always vibrate when you call and you are able to use Siri, it seems there is a problem with the backlight on your iPhone.

  Because you have a separate hardware two related issues going on with your iPhone, I suggest putting your iPhone in an Apple Retail Store or Apple authorized service for an assessment of your device provider. More information about these options can be found in the following link.

  Apple - Support - Service Response Center

  See you soon!

• tried to install a new copy of Windows XP Home. Everything is OK until the final phase, when the "blue-screen" appeared during the installation of the drivers.

  Installation of xp and blue screen of death

  Hello

  I recently formatted the partition boot and recovery of a laptop Medion2230, then merged the two partitions in a single NTFS partition.  Don't ask why, it's a long story.

  Then, tried to install a new copy of Windows XP Home.  Everything is OK until the final phase, when the "Blue Screen of death" appeared during the installation of the drivers. Restarted and installing XP as normal to repeat the first onboard staged and went to the "blue screen" at the same point as before.

  Using some diagnostic software, I reformatted the drive again, loaded XP set up and I had the same problem.

  Someone knows what to do?

  Thank you allionii123

  Now solved and pc with Windows XP home.

  Discovered a trick online, who said that at the beginning of XP installation, press F5, and this leads to a screen option - select 'standard pc' and continue with the installation of XP.

  (Again), formatted hard drive ran XP installation and followed above point.

  Worked the first time.

  Thank you very much for your advice.

  I think you can pressing F5 or F7...

  How to impose a layer of HAL during an upgrade or an installation of Windows XP

  Impose a HAL

  To prevent Windows XP to automatically determine the system HAL during the upgrade or installation of Windows XP, you can manually force in a system HAL. To impose an Abstraction Layer HAL during a upgrade or installation of Windows XP, follow these steps:

  1. During the phase in text mode of Setup, when you receive the message at the bottom of the screen, press F5:
     Press F6 if you need to install a third-party RAID or SCSI driver.

     Note If you press F7, the Standard PC HAL loads and the ACPI enforcement is bypassed.

  I would not need this except in the systems of many older and low end... :-(  After all, in the same article, for Standard PC they say: "the CPU can be a 386, 486, Pentium, Pentium II, or Pentium III '...

  Thanks for letting us know what you were doing.  Do you have all the necessary drivers after loading Windows XP?  I would not recommend using the default drivers for any hardware - always see what the manufacturer offers on their web page for each component of your system - card motherboard chipset, audio, video, network devices, etc.

• I downloaded the trial of the creative cloud vision. But why does the application display a completely black screen?

  I downloaded the trial of the creative cloud vision. But why does the application display a completely black screen?

  I can open the CC but I don't see anything in it.

  I downloaded and months before photoshop. I still see something at the window right there.

  But now, I see the dark window. So I couldn't download the Adobe Illustrator.

  Please help.

  Hello

  Please see the thread below where this issue was discussed:

  Re: screen creative black cloud

  Kind regards

  Sheena

• How to print photos when the display screen is white? The image is missing in it.

  How to print photos when the display screen is blank?  It shows only a white screen empty when I select the photo and press on print.

  You click on a film image in the print module? And, I guess you don't have to go to the Print module, right?  Additionally, make sure that you have chosen to make a custom package.  If you chose the custom package you need to drag and drop images and organize them.

• Video without stopping on the last image, when the splash screen appears

  I'm having what looks like a subtle bug in v20. I have an application one question. The opening in a 7 second video screen. I have a MSO under the video, which is set to auto-play, every 2 seconds, play 1 time, finally stop image. The first State of the DSO is a black screen (to match the beginning of the video), and the second State of the ASM corresponds to the last frame of the video.

  I did this same technique many times before, and it worked fine. It works perfectly here when I preview the app in the content viewer. But when I built the app and view the developer app on my iPad, something funny happens:

  The first time you run the application, the startup screen appears of course while the application loads into memory. Then the video opening plays, but when the video is finished, a black screen (probably the first State of the DSO). Whenever you come back on the video, the same thing happens.

  But, if I glisser drag on the third screen, quit the application and then go back into the application, then the opening video and the mso works perfectly. Until I double click the home button, remove the application from memory and run it again fresh, then the startup screen and then I can repeat the problem.

  This smells like a bug to me. Any ideas for workarounds that anyone can think?

  Have you tested it on the iPad? There has got to be a v23 folio in a viewer v23 on an iPad or an iPhone.

• Satellite A500 - screen is completely black

  I got my laptop Satellite A500 for about 4 months and already there is a problem with it.

  After that I had played a few MMO on it for a while so I decided to power out of the night. The next day I started my A500 and there was a completely gray screen and I waited for at least half an hour before holding the power button for 6 seconds just to restart, so when my A500 started to the top of the screen was completely black, but the power LED light was off, but the only lights which were the key commands on the Panel next to the screen and the power light to indicate that it carried out.

  After several tries, the problem had been held, is anyway to fix this?

  Hi mate,

  Have you plugged an external monitor? I mean without it it's hard to say what causes this problem, but I guess that he associated material s. So if the external proceedings, I think that only the internal display is the cause maybe the FL inverter?

  Anyway, in both cases you need assistance from an authorized service provider. Guys can check your laptop and fix it for you. :)

• Satellite L500 - screen is completely black after stand-by

  I have a L500 and after that my computer is on standby, the tried to reactivate it. Now it will not display anything on the screen its completely black and have no idea of what should happen or do.

  Can anyone help?

  Hey,.

  You see something on a screen? The internal screen is probably defective, so you don t see anything.

  If an external monitor stays black I would try to remove the battery and unplug the AC adapter. Then wait at least one or all the night. Now connect the AC adapter and install the battery. Before you turn on the laptop, make sure that the battery is fully charged. Now, try to start your laptop and check what is happening.

  In the worst case it serious hardware malfunction and that means that you would need professional assistance service authorized in your country.

• My screen goes black after a short so that after starting my laptop. I plugged an additional screen now to be able to use my laptop, but the laptop screen keeps turning black shortly after. How can I fix it?

  My screen goes black after a short so that after starting my laptop. I plugged an additional screen now to be able to use my laptop, but the laptop screen keeps turning black shortly after. How can I fix it?

  Hello

  I'm sorry to say this, but it points to a UPS of material about to fail.

  You will need to bring the laptop to get it replaced.

  Slan go foill, Paul

• My laptop screen went completely black when I plugged in the charger. Help, please!

  My dough went critical at seven percent (7%) last night and I went down to the charger plugged it. The screen is totally black, but its still on.

  PS. It is not a problem of screen brightness.

  A concerned customer.

  You need to make a diagnosis.

  If your laptop has a VGA video port, try connecting a monitor to it.

  Have you tried a full stop and restart?  Stop, remove the battery.  Hold the button for 7 seconds.  Now, without the battery, a power.  If this brings a screen, stop it again and re - install the battery and try again.

  Until you can provide more specific information, no one will be able to help you.

• SWITCH UPWARDS A NOTICE + PRIVACY PROBLEM WHEN THE FIRST SCREEN LOCK

  Hi all

  I have an Iphone 6 and since I did the update for IOS 10, I have a few problems:

  I can't pass up a push notification when arrive on the screen with your finger, the little thing do missing since (I also have an iphone 5s and I can still do it, also with 10 IOS installed on it) is so very strange to me, I tried to change phone etc... but nothing to do.

  Then, my second problem is confidentiality on the first screen of the phone lock. When I receive an email from outlook, for example, anyone who does not know my zaihon can open, reply, delete, even for the notification of whatsapp etc...

  If anyone knows that a solution would be very nice to share.

  Thanks in advance,

  Maud

  You can disable the mail view in the screen to notify in settings/Notification Center / Mail:

  Use the Notifications on your iPhone, iPad and iPod touch - Apple Support

  You can also delete the Widget for this:

  Use Widgets on your iPhone, iPad and iPod touch - Apple Support

• Laptop turn on but the screen is completely black

  Hi guys,.

  I was wondering if someone have an idea as to why my laptop (which was working perfectly last night), now has a black screen when I try to turn it on.
  I read in some other forums who offered to take out the battery and hold the power button, but that didn't work...

  Remedies?
  Thank you.
  Jess.

  Hi Jess

  Is a busy HARD disk when you start your laptop?
  You hear Windows sound?

  If possible try to connect your laptop to the external screen or a TV to see if you can see anything on an external device.

• Windows XP: Windows XP automatically restarts when the logon screen is delivered.

  I installed Windows XP last year. But recently there is a problem with my Windows XP. (My Windows XP is joined to a domain).

  When I booted my Windows XP

  (1) I joined to a domain.

  (2) I turned on my computer.

  (3) when the "Windows XP" loading screen disappeared, the opening of session came.

  (4) until I press Ctrl-Alt-Delete, it is automatically restarted my computer.

  Can anyone suggest me some ideas?

  I started in safe mode. Nothing happens.

  I also tried to press F8 and select "last good known...". «It worked, no automatic restart, I don't want to press F8 and select "last know good...» "each time when I tuen on my computer.

  In mode "last known...". "I was able to login but when I want to stop, the system has restarted rather than stop it.

  Additional information to my Windows XP:

  Windows XP Professional, Service Pack 3. 1.95 GB of RAM

  Hello

  Like you are on a domain, the question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads

• HP 15 Notebook PC L3Q92EA #ABU: HP Pavilion, 8.1 Win "Please wait" when the unlock screen saver

  Just bought an HP 15 Win8.1 running laptop.  I think it's a huge pain to use.  Once the screen lock is committed, it takes forever to get the login screen to appear.

  I move the mouse or press a key to get the screen to go back, but I see is the screen "Please wait" for more than a minute then a background appears.  Click the mouse and I have one more minute of "Please wait" before the logon screen appears.

  Can anyone help, until the laptop goes through the window?

  Hello

  Thanks for posting your concern on the Forums for Support and sorry about the problem you are having. I went through your post and it sounds like I should be able to help with the problem.

  I suggest you perform the test (Test of the HARD disk) on the computer. Follow the steps below-

  • Switch off the appliance.
  • To turn back press the power button and as soon as you release, keep pressing the "ESC" key, unless a screen comes up, you might want to wait a minute while tapping the button.
  • In the start menu, choose F2 - System Diagnostics.
  • HDD test would be under the Test component. (usually, it is recommended to test rapid and wide, but for now because the PC is new I rather suggest you simply run the Quick Test).
  • After you choose the Quick Test, click on run once.

  If he succeeds, you can proceed with the recovery, part if she fails to give a call to tech support at the number mentioned below, since the unit is under warranty, you should be able to get help to get the drive replaced.

  On the recovery procedure, its complete restoration of unit settings factory which means that the data on the computer is cleared and with it, the software that can be installed on it. Please follow the steps below to perform recovery-

  • Switch off the appliance.
  • To turn back press the power button and as soon as you release, keep pressing the "ESC" key, unless a screen comes up, you might want to wait a minute while tapping the button.
  • In the start menu, choose F11 - system recovery.
  • On the next page of options, you can choose - "troubleshooting." (If it is a unit of windows 8, or you can skip this step)
  • On the next page, you will need to choose "Recovery Manager". (If it is a unit of windows 8, or you can skip this step)
  • On the next page in the first column, under "I need help immediately", you must choose "Reduced Image Recovery"
    • Now, here, you can get an option to backup your files, because it would be an option to say - recover after saving files or recover without backup of data.
    • You will need to insert the disc followed the screen - instructions here on and unit should be returned to its original state.

  Now if you need help email us back or call HP SUPPORT @ 1-800-474-6836 [24/7 SUPPORT].

  Although I work for HP, but I am personally.

  Please click "Accept as Solution" If you feel my post solved your problem, it will help others find the solution. Click on the 'Bravo Thumbs Up' on the left to say 'Thank you' for helping!

  Concerning

  Aks3621