Tecra M4: TMESBS32. EXE stops hibernation

Similar Questions

• Tecra S11 - 11 H - stop with the fan turns

  Tecra S11 - 11 H stops - seems ok, but when the screen is off, after 3 seconds, CPU-fan begins to operate.
  Pressing the power button / stop a few seconds turns off the machine and shut the fan.

  Support put me to upgrade to the latest version of the prints digital-device driver, but I found the software, no drivers.

  They also told me to upgrade the bios to the latest version.

  Problem is that this update of the bios will not start. He complains about power cord power supply not connected or battery power is low.
  The two isn't true - power cord is plugged in and the battery is fully charged.

  What could I do?

  TIA

  LGKF

  Hi lgkf,.

  Yes, I think the support from Toshiba is just because I found this article on the Toshiba page:
  http://APS2.toshiba-tro.de/KB0/TSB0C032L0000R01.htm

  As you can see, update the fingerprint software can help you get rid of this problem, then you must update the software of fingerprint. The pilot is a part of the software, then download the package for fingerprints on the Web from Toshiba site.

  Uninstall the older version, reboot and install the downloaded version.

  Check this box!

• TosSmartSrv.exe stops working when you start up Vista

  TosSmartSrv.exe stops working whenever I start my computer (Vista)

  What is this file, and what I can do to resolve the situation?

  I have a new Satellite Toshiba Quad Core and have not seen this message on my old Toshiba Satellite.

  Hello

  Toshiba Satellite Quad Core says nothing about your model of laptop so what model you have exactly?

  I tried on my laptop for this file, and it seems that it is for the utility alert SSD HARD drive. It s stored in this directory:
  C:\Program Toshiba Toshiba HDD SSD Alert

  In your case, I would try to reinstall the utility. I also checked the Toshiba page and there you can download. Just search your laptop model on the driver download page and you will find! ;)

  Welcome them

• Explorer.exe stops when the computer is shut down

  Explorer.exe stops when the computer is shut down

  Hi DickKimberley,

  ·         What exactly happens when you try to shut down the computer?

  ·         You receive an error message error code?

  ·         Did you do changes on the computer before the show?

  Follow the suggestions below for a possible solution:

  Method 1: I suggest you to consult the article in the Microsoft Knowledge Base and check.

  Advanced Troubleshooting for shutdown problems in Windows XP

  http://support.Microsoft.com/kb/308029

   

  Method 2: If the method above doesn't follow the article mentioned below.

   

  Windows stops responding during Windows XP shut down

  http://support.Microsoft.com/kb/307274

  Let us know if that helps.

• CAgent32.exe stopped working and was closed at the start of windows.

  Original title: CAgent32.exe stopped working and was closed

  Whenever I start my computer a Windows tab will appear that reads CAgent32.exe stopped working and was closed? How can I fix it? Thank you

  Hello

  1. what happens when you try to uninstall or disable the program?

  2. you receive messages or error codes?

  3. have you made a recent software or hardware changes to the system?

  You can read the following article and try to run the Fixit and check if it helps.

  Diagnose and solve the program installation and uninstallation problems automatically

• at startup I get the error message that the gamevance.exe stop working

  original title: gamevance.exe for vista

  at startup I get the error message that the gamevance.exe stop working, I went to start to delete, but do not have the option to remove it.

  Hi JoAnneKimmey and pugmolly,

  When looking for this, it seems to be malware, so I'll include a link to a useful thread in which you can find a solution:

  How to get rid of malware

• mysqld.exe stopped working and was closed

  Whenmy computer starts, I get and error message "mysqld.exe stopped working and was closed". What is the solution?

  Hi vinaypahwa,

  Looks like you have an unwanted program that loads when Windows starts.
  The solution is to disable this program of commissioning by performing a clean boot:
  http://support.Microsoft.com/kb/929135
  You can also manually check which starts up by looking at the startup of the System Configuration dialog box tab and disable what you do not want to start.
  I hope this helps.

• Launcher main exe stopped working so my logitech webcam does'nt work, what can I do?

  My webcam logitech 170 does'nt works because Launcher main exe stopped working what can I do about it?

  There are a number of discussions in Logitech forums at the topic "main Launcher" (not sure whether an any of them will be useful): http://forums.logitech.com/t5/forums/searchpage/tab/message?location=Board%3Aquickcam_software&q=launcher+main#message-list

  Logitech product support can also help: http://www.logitech.com/en-us/support-downloads?debug=0

• Explorer.exe stops and restarts constantly - I have a solution but its only temporary.

  Had no problems with Windows 7 for a year. Then recently explorer.exe stops and restarts repeatedly, over and over again each 5-10secs. Our Event Viewer error is a .dll module in User\User blame name\Apps\Local\, called eciwavatebiwe.dll. I find this .dll and when I rename the judgment falls down, but instead I raise an alert at startup that windows does not find this file (I click just the red x).

  I used virus and sfc/scannow ladies, but no error reported.

  The file in question announced swapper Windows NT caps lock ctrl but Googling is not this .dll anywhere.

  Any ideas what going on?

  Chris

  eciwavatebiwe.dll is a virus what I see. Remove it and start regedit.exe and findeciwavatebiwe.dll and delete everything you find.

  Also scan your system with your scanner, AntiVirus and Malwarebytes' Anti-Malware (http://www.malwarebytes.org/mbam.php).

  André

  "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

• Tecra M2: Traveling around in hibernation mode?

  Dear Sir.

  I use my tecra m2 for medical purposes for most, I'm patient and each time I have to open and close windows: one thing a lot of time: is it possible to travel in a hibernation and is it safe for the HD?
  Or it is better each time to stop?

  Thanks in advance

  Hello

  To save energy, the laptops can go into hibernation mode, preserving the autonomy and your work. Hibernation is a great feature that is often sadly ignored despite its great benefits. It's like the Stand By mode where you save the battery, but instead simply to enter a low power state, the computer is actually off. Everything in memory is saved, however, so that when the computer is turned on again, it's like you never left.

  Remember that it is advisable to restart the unit from time to time. ;)

• Tecra M2: sound system stops working after a while

  Hello

  I used my TECRA M2 a year without serious problems. A moth started it my problems with audio - after the start (no matter if via boot or wake up from hibernation) his (speakers) system is functioning normally. After a while (several tens of minutes, hours) sound system stops working (no sound from your speakers or headphones). No errors appear, but not sound. When you try to adjust the volume via the Windows icon on the bar the task CPU usage becomes very high.

  I decided to reinstall my M2 - the first attempt was clean install of WinXP SP2 standard support - sound problem has not changed. Today I decided to restore the system recovery CD, but the result is the same :-(

  Any idea? -I suppose that problem Council... Now, I made a mistake when entering - beeps system (such a beep as during startup) - interesting :-/

  Except sound problem - another strange thing - when I send my XP to restart in about 10% of the attempts he goes off and does not start. Starts normally after pressing power button...

  Any ideas would be much appreciated
  TX

  Hello

  Looks like a hardware malfunction.
  Maybe it s caused by overheating.
  Check the cooling modules and try to clean it with the vacuum cleaner.

  If it doesn t help you should contact the Toshiba ASP.

• Tecra A8 - Touchpad has stopped working

  Hi all!

  I have a Tecra A8 (model: PTA83E) who has an ALPS touchpad. The touchpad has stopped working even if it is visible and fully operational in 'Device Manager' and also the 'Control Panel '. Apparently there is nothing wrong with it but the touchpad does not meet the clicks or touchs, it seems as if it has been disabled, but said, in Device Manager, the information is 'this device is functioning.

  I updated the OS to Windows 7 Enterprise and I would like to activate the touchpad if not I should always use a usb mouse. I searched the touchpad drivers but it seems they are Don t.

  This is the information that I can view in "Device Manager", about the pilot:
  -Controller version: 7.0.302.3
  -Date: 26/09/2006

  Thanks to you all.

  Hello

  You have activated the touchad by pressing FN + F9?

• All new Tecra A10 won't stop beeping... 3 beeps HI-LO-HI

  Hello there are experts...

  I just got a new work for laptop Toshiba Tecra A-10, and it won't stop beeping.

  Everything works fine, but every 2 minutes, or until you get 3 beeps, low high high. I can mute the PC so I can't hear it... But what the hell is wrong?

  Beeps start as soon as I get to the login screen after you start the system. The start process seems fine, I get the beep POST so I guess it's all good.

  The battery is full, and the beeps continue with the power cable in or out and any battery capacity. I restarted many times and still do not know the computer on top of his head and he's away until Monday. I just want to go to the bottom of this myself, I'm sure it's something simple. The laptop is brand new also probably isn't a BIOS warning (I'm no expert - it may be).

  I wandered through forum after forum and no one seems to have the same problem, then it might be something like one of these Toshiba applications was trying to tell me something?

  Please help, anyone out there with all the answers?

  Thanks guys,.
  Steve K

  In addition, there are a few programs installed since the laptop is... including the ABECAS and a few other software packages business including the TREND. Could this be something to do with those?

• HP 7 flow won't stop hibernating

  I have upgraded to Windows 10 recently... and things have been slow but now I turn on my Tablet and there are points of loading in circulation and it says hibernating...
  How can I stop this and use my Tablet?

  Hi there @Rkbarb1,

  Welcome to the Forums of HP Support!  It's a good place to find the help you need, other users, HP experts and other support staff.  I understand that your tablet is often stuck in hibernation after upgrade to Windows 10.  I'm happy to help you with this.

  I suggest that you work well this paper: computers HP - sleep and hibernation problems (Windows, 10, 8)

  On the question of the overall sluggishness, you can find one or two of them help: HP PC - computer is slow (10 Windows), HP - slow Internet troubleshooting (10, 8 Windows) computers.

  Please let me know if it works for you and if it does not solve your problem, please mark this message as a solution. Bravo would be appreciated as well.

• Tecra A8 don't stop

  Hello, when I try to stop the Tecra A8 or Satellite Pro A120 specifications they will block empty background. All solvings without having to reinstall all of the machines?

  Hello

  have you recently changed anything on your software or installed some new firmware? Maybe you did some driver updates?

  Would be interesting since these errors are often caused software problems hollow.
  It would be nice to hear comments on what you have installed/updated / uninstalled on your system.

  By the way: what operating system is installed on your machine?

  Good bye