Tecra M5-103: cannot get external DVI connetion to the monitor

Hello

I am unable to get the external DVI connetion to my flat screen monitor to work.

I tried to plug in there by itself and restarts, plug with d - sub and reboot, by reconnecting it with reboot is not yet etc does not work.

Someone had problems with this? Or he successfully?

Thank you

Richard

Hello

One question: the laptop supports a DVI?
As far as I know the laptop has only RGB (monitor output port) and S-video output port.

If you want to use an external monitor you need to connect it to the RGB port, then switch to the external display with the key FN + F5 combination

Tags: Toshiba

Similar Questions

  • on my laptop of his fathers ' key stopped working and now he cannot get on his laptop because the password has a S in there.

    original title: laptop trouble

    Good so recently on my laptop of his fathers has ' key stopped working and now he cannot get on his laptop because the password has a S in there. He tried to clean the key to bored all possible ways, and nothing works. He wondered if he had a Ctrl function that would allow him to put a s with the key or bypass the password lock. Also, it has no access to a USB keybored.

    If the account in question was not the built-in account named Administrator, and then log on to that account and go to control panel > users to change the password.

    The password for the administrator built-in account is blank (no password).

    To connect to the built-in Administrator account:

    Reboot safe mode: press F8 immediately after power on.  The administrator account is displayed on the homescreen mode without failure.

  • Photos appear white and cannot get images to display on the photos

    Original title: I CANNOT GET PICTURES TO DISPLAY ON THUMNAILS, THEY APPEAR as WHITE, WITH a RECORD #, WHY?

    WHEN I NAVIGATE TO UPLOAD PICTURES, MY PICTURES APPEAR IN WHITE, WITH A FILE # BELOW THEM, I CAN'T S EE THE MINIATURE OF THE PHOTOS, I DID CHANGE SOMETHING?

    Hi marvin z..

    1. are you using Windows Photo gallery?

    2. were you able to view a thumbnail preview?

    2. you remember to make changes to the computer before this problem?

    You need enable preview of thumbnails in the navigation pane.

    a. open the pictures folder by clicking the Start button, click photos.

    b. in the Navigation pane, click the folder that contains the images that you want to display.

    All images in this folder are displayed.

    c. click on the arrow next to the view button and then move the slider to change the size of thumbnails.

    Check out the link:

    View and print picture thumbnails

    http://Windows.Microsoft.com/en-us/Windows-Vista/view-and-print-picture-thumbnails

    Also check out the link:

    Change the thumbnail size details and file

    http://Windows.Microsoft.com/en-us/Windows-Vista/change-thumbnail-size-and-file-details

    Hope this information is useful.

    Jeremy K
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

    If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • VMware workstation 8 briged connection cannot get an ip address from the dhcp server

    Hello, I hope someone can help me with this problem, my virtual machines are unable to obtain an ip address from my dhcp server in windows server 2008R2.

    VMware workstation 8 is running in windows 7 proff. 64-bit OS. My gets physical computer an ip Server dhcp without problem have access to the internet and everything works fine, but my VMs for some reason any cannot obtain an ip address from the DHCP server.  I updated virtual nework Briged editor one of my physical network interface cards. Then I put my VM NIC to briged in for some reason my VMs are unable to obtain an ip address. The ips only I get are 169.254.43.129 Add 255.255.0.0. any help would be very happy. Thank you very much.

    FYI - you have posted some of the vmware.log

  • Cannot get 12.4SE to use the encrypted password for ODBC

    Hello

    We run gendata/genprint on the Linux platform and move from 11.5 to 12.4SE. The MRL is in a database of DB2 installed on MVS (and connect via ODBC). We installed the 12.4SE on the server, the engines and copied the entire folder structure, including our ISP * files, our installation of 11.5 - didn't change at all. If I run the motors with an unencrypted password, it works fine. The problem I'm running is when I run with a password encrypted in the ODBC DBHandler (that is what we have in our configuration 11.5), I get a lot of mistakes (the first letter is actually absent from these messages, I'm not myself truncating):

    Error in main(): unable to RunGenData(). See the errors file for more messages.

    Warning in RPDefDisplayProc(): display user procedure has not been defined.

    arningCountSIFileNamecratch/home/dmkr/documaker/rel124/rps100/rplib/unix /... /c/rperr.cSILineNumber099

    rrorCountSIFileNamecratch/home/dmkr/documaker/rel124/rps100/rplib/unix /... /c/rperr.cSILineNumber115

    lapsedTimeSIFileNamecratch/home/dmkr/documaker/rel124/rps100/rplib/unix /... /c/rperr.cSILineNumber193

    enData Completed-

    When I go to the ERRFILE.dat, I see:

    Transaction error report - system timestamp: Mon oct 19 12:36:33 2015
    DM12041: Error: error library FAP: Transaction: <>, area: ODBC error >
    Code1: <-30082 >, code2: < 4294937214 >
    message: 08001-30082 [unixODBC] [IBM] [CLI driver] security SQL30082N treatment failed with reason "3' ("PASSWORD MISSING").  SQLSTATE = 08001 >.
    DM12041: Error: error library FAP: Transaction: <>, area: < LBYInitializeLoaders() >
    Code1: < 0 >, code2: < 0 >
    message: failed to initialize the library < FJ§ > >.
    DM15066: Error RunGenData: could not LBYInitializeLoaders().   The system is configured to use the library, but the library could not be initialized.  Verify that the library is properly specified in the INI file and is accessible.

    == > Number of warning: 0
    == > Error number: 3

    When I look to the top of DM15066, I see:

    Explanation
    The call to LBYInitializeLoaders failed in function (GenTrn.c, GenData.c or GenPrint/PrintEnv.c). The usual reason that LBYInitializeLoaders do not is that the library is stored in a DBMS (DB2, Oracle or SQL Server) and the DBMS or database in the DBMS is not accessible.

    Programmer's response
    Check that the DBMS or database in the DBMS used by the MRL is running. If this isn't the case, please re - initialize the DBMS or database in the DBMS.

    Anyone has an idea why my installation 12.4SE dislikes the encrypted passwords?

    Thank you

    Gregg

    I hope that I am not striking myself, but I think I have it working now. I started a support ticket about not being not able to get the cryrun utility to work on Linux, and when I hit the stage 2 ("solutions"), one of the proposed solutions talked about this specific question. He explained that specifying a folder deflib allow the utility Cryruw32.exe to place a file 'Omar', and that you then this odek file in your deflib when you try to run the documaker engine. I read the release notes, pointing to the "reference help utilities" for more information, but there is NOTHING in this guide for the Cryrun utility which mentions the file "odek".

    Anywho, I made a generic file deflib, run the utility, FTP'd the file down to the deflib of my application on the Linux server, copied the encrypted password new/different in fsiuser.ini, and voila, it ran!

    For those interested, it was Doc ID 2006951.1

    Thanks for your help.

  • Tecra A10 - refurbished - cannot get it connected to my home network

    I just got this Tecra A10-104 refurbished Laptop... before I take this back I ask here in case where theres something I missed as I am unable to get it connected to my home network.

    I use a Belkin wireless router that has 2 main (LAN) directly connected PC and another PC connected wireless.
    It's my router: http://www.belkin.com/uk/support/article/?lid=enu&pid=F5D8233uk4&aid=9238&scid=0

    All PC connected and fine work.
    Now I'm setting up this laptop to connect.

    I uninstalled the Vista Business and ussed the product recovery disc that came with the Tecra XP Pro.

    Is my wireless card: Intel (r) Wireless WiFi Link 5100 (pilot Date: 27/04/2008 - the driver Version: 12.0.0.73)

    He sees the network, but no matter what I try just does not connect.

    What I've done so far (read before suggesting things I've already tried):

    Reconfigured routers WPS to the shared key system.

    Ensured that the wireless adapter's parameters defined at 20 / 40 Hz (automatic)

    Restarted the router, cable modem & laptop several times

    Laptop wireless button is turned on.

    FN + F8 to activate BLUETOOTH WIFI (ON) (OFF)

    Wireless network added to settings Auto Connect with the end SSID and password encryption method.

    Click on connect when network appear in the revamped network and Password Viewer dialog.

    Does not.

    I would add that the laptop has no problem connecting via its Gigabit LAN port.

    Something else I'm missing?

    Thanks in advance.

    EDIT: Double post deleted.

    UPDATE:

    The next thing I tried was to reinstall Vista Professional recovery disk to see if it has suffered from the same problem.

    Wireless has worked under Vista, and despite the updates I was offered, worked without having to update all the drivers.

    This got me thinking... so the question is probably DRIVER XP related.
    What I've done now is to back up all the updates driver told me to download TEMPRO (BIOS & Manager wireless updates included).

    I think part of the problem is that only TEMPRO works under Vista (not XP) so you are not informed of any updates may be required if you upgrade to XP directly after the purchase (which is what I did).

  • Cannot get T500 to display on the external monitor

    Hello
    I'm running Windows 7 on a ThinkPad T500 (type 2082.BSG), and I'm having problems after have recently updated my display on the Lenovo site software (read the list of installed software, I think that the installation of the software that is the cause of the problem is "ThinkPad features video [AMD switchable Graphics (M8x)] for Windows 7 [32/64 bit] ') version 8.752.4 - 101022 a-107489C-Lenovo). Before the update my computer has guessed what display is active (laptop screen or external monitor) and used the active display. For example, when the laptop is docked and the cover closed he used the external monitor. After the update when the laptop is connected and the lid is closed, I can't display on the external monitor. I have to open the lid and use the Fn + F7 to get the display on the external monitor. Can anyone tell me please what settings should I use to get the old behavior.

    Kind regards

    bostjanv

    The previous is an old post, but as there was no response, and I recently solved the problem, I write in case someone else runs into the same problem.

    After having encountered the problem I restored the factory default driver (which does not show the problem). However, lately I received another message to the effect that it is recommended to install Lenovo "Thinkpad video Features (AMD Switchable Graphics...). ...". I installed the software but the problem described in my original message reappeared. However, this time, the software of (the age AMD) had a "driver update" option and my video material is correctly recognized and the correct driver has been downloaded from the AMD website, after which the problem described in my original post disappeared.

    Kind regards

    bostjanv

  • Re: Tecra R840-199 - cannot get its ethernet card to pick up the IP

    Hello
    I have Tecra R840-199, Running Win 7 64 bit.
    I installed intel drivers for the network card. (Intgel 82579LM)
    the card is recognized on the system,

    but it will not pick up an IP address. (the network cable and port are working)
    Any suggestions on how to solve this problem.
    Ive updated the bios, and software service does not pick up all updated

    Hello

    According to the specifications of the laptop this laptop was offered with preinstalled professional Win7 64 bit. Original recovery image contains all the necessary drivers and after first boot all hardware components are installed correctly.

    Usually the LAN connection cable should be enough and your laptop should have full access to the network.

    Until we start the discussion, I have some questions for you:
    You use this original OS version that you got with your laptop?
    You have installed driver from the Toshiba download page?
    You may have problems at home or in your business?

  • Cannot get old backup files in the external hard drive

    Separated from this thread.

    I'm having the same problem - I did a file with windows vista and then put backup.exe at level to windows 7 and now I can't see my files. Help!

    Windows 7 can read files from Vista backup natively as they both use the same backup engine. However the files generated by the backup and restore are not .exe files

    You must run backup and restore and then access the backup image to open it.

  • Cannot get signal when you connect the TV to HDMI port.

    * Original title: HDMI Signal

    Hello. My nam is Kieu. I have a problem and and we hope you guys can helo me. I just bought a Gateway desktop all-in-one computer and tried to connect it to the TV via the HDMI port, but I could not get signal on my TV. Help, please.
    Thank you very much

    Hi David,

    Thanks for posting your query in Microsoft Community Forum!

    According to the description of the problem, it seems that you are unable to get the signal when you connect the TV to HDMI port.

    I will certainly help you with this issue.

    Here are some steps that you can try in order to solve the problem.

    Step 1. First you need a video cable to make the physical connection. For a better image quality, you need to connect the computer to the TV using standard VGA ports or via DVI to HDMI Cable provided your TV supports these ports.

    Step 2. Open thedisplay settings' ' in your Vista computer and Activate the output to the TV screen. You can reflect the content of your computer on the TV or extend the display as a double screen control.

    Step 3 Pick up your TV remote and switch to "External inputs" in the menu. You need to change the value by default "Video 1" to a different selection which may be "HDMI 1" or "video 2" depending on how you made the connection. "

    Important: Make sure you connect the cable to the TV before turning on the computer, because sometimes it may not recognize the external display.

    You may also change the resolution of your TV screen using the display settings in your panel of control remains the image may appear distorted.

    For more information, see the article.

    Connect your computer to a TV

    http://Windows.Microsoft.com/en-us/Windows-Vista/connect-your-computer-to-a-TV

    If anything in my post is not clear or if you have any questions on Windows, feel free to let us know. It is our pleasure to be of service.

  • Cannot get my sync data after the reset password

    Greetings,
    I have reinstalled the OS on my laptop and tried to Resync all my favorites etc. Last time I did this, it was no problem. However, this time, it would not accept my password for some reason any. It kept showing me "password incorrect" even if the password was correct. I had to reset my pass and after that I do not seem to have my data synchronized back. How can I solve this problem and get everything I need again?
    Thanks in advance.

    The synchronization service uses a synchronization key to encrypt the data locally before you download
    This sync key is generated internally from the password of your account from Firefox, you need not worry about this.
    Without the password, it is not possible to decrypt the data stored on the server, because the good sync key cannot be generated.
    This synchronization key changes when you change the password of the Firefox account and you will lose all data stored on the server when you change the password of the account synchronization.

  • Cannot get administrator access to download the Windows 8.1 upgrade

    Hello.

    I have a new XPS8700.  I was able to download the Windows 8.1 since the MS. Store upgrade  My first problem is the lack of updates from Windows, I did, and now I can see the 8.1 update in the store.  I can also download updates to other access points.

    My problem is a continual notice whenever I hit the download that I must log in to an account with admin access.  Best I can tell, this and other forums have shown me how to add the Admin feature with the command prompt.  I even created a second account and did the same thing.  In the summary screen of the user in the Control Panel, the two users show "administrator."  But I still can't access

    I tried "net user administrator / Active: Yes" but also tried the same thing with permutation of my name for the administrator

    The real ' administrator' user cannot do anything in the App Store.  This seems to be what's supposed to happen.

    Does anyone have advice?

    Very frustrating to say the least

    Sounds like a bad set-up. I would advise to uninstall KB2871389 and put it back manually. Also uninstall McAfee and then retry the update.

    http://dellwindowsreinstallationguide.com/download-Microsoft-Windows-and-Office/Download-Microsoft-Windows/upgrading-to-Windows-8-1-from-Windows-8-0-via-the-Microsoft-store/

    I also recommend asking a reinstallation DVD Windows 8 of Dell.

    http://dellwindowsreinstallationguide.com/download-Microsoft-Windows-and-Office/Download-Microsoft-Windows/request-a-reinstallation-DVD-from-Dell/

    Personally, I prefer a clean install and certainly have a way to clean install would be beneficial to you if you are having these problems with the factory settings. For instructions on how to clean installation guide reinstalling Windows / A Clean install of Windows 8.1:

    http://dellwindowsreinstallationguide.com/

    Unfortunately, the combination of policies (blocking Windows 8.1 media to accept product keys Windows 8.0) Microsoft and Dell systems with Windows 8.1 not marketed is problematic for the end user. Dell won't be able send you reinstalling Windows 8.0 media. If you can get your hands on the Windows media 8.1, then you can clean install with him using the following arounds:

    http://dellwindowsreinstallationguide.com/a-clean-install-of-Windows-8-1/Microsoft-product-activation/

    Note If you ask to request installation media the DVD and not the USB as DVD can contain additional Dell drivers that may cause problems similar to the factory settings.

  • Live2011 Windows Messenger. cannot get at any stage of the operation can not even log in I have deleted the program and down he loaded several times

    Windows live messenger, message get the application could not start due to its configeration side by side is incorrect. see the application log. This means nothing to me. I have uninstalled and reinstalled several times?

    The issue is part of Windows Live Solution Center.
    Thanks for posting to the category of Messenger: http://windowslivehelp.com/forums.aspx?productid=2 for the benefit of other people looking for answers, please mark as answer suggestion if it solves your problem.

  • I get "unable to send" Ox800c0014 error code and I cannot get it off and delete the message. Can help

    I obviously sent an e-mail that caused the response above, and I can't seem to understand how to remove the message to get rid of this pop up whenever I try to sync. Can anyone help?

    Hi Richard,

    Thanks for the post. I'd be happy to help your with the question.

    To help you with the problem, we need more information. Please answer the following questions:

    1. Which e-mail account do you use?

    2. How do access you your email account (using the web browser or Windows Live Mail)?

    3. Did you of recent changes to the computer?

    While you answer, try the suggestions below. R feel, renew all connections.

    Click Start, click principally made programs, Accessories, right-click guest, and then click run as administrator.

     

    Enter the command below and press ENTER.

    Ipconfig/release

    Enter the command below and press ENTER.

    Ipconfig / renew

    Enter the command below and press ENTER.

    netsh winsock reset

     

    Try this steps and check if this solves the problem. If the problem persists, please respond with more information and we will be happy to help you.

  • Cannot get on parent account saying the password is incorrect

    Could not get on the parent account he repeats to me password is incorrect

    By parental account , I assume you mean your account that has administrator permissions?

    You might be able to get into the native administrator account and reset the password. See this help possible partularly response by Malkeleah on native admin account activation in method 1 access to its post. By default, the native admin account is disabled when Windows 7 is installed.

    http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-security/lost-administrator-account-on-Windows-7/62a99dcc-B976-4AD1-9ac5-e7bf803eab83

    Also if you changed the password, ask them to help.

    Finally, make sure that your switch is not lit. Its possible your using the correct password but in all uppercase for example...

Maybe you are looking for

  • "Icons and text" style toolbar buttons have borders

    Don't know whatever the title, I can say, I've updated for Firefox 8 and the text/icon style icons have more distinctly bordered. If it was intentional, I have trouble finding the option to disable this visually discordant style change.

  • Satellite Pro - strange question when I type fast

    I know it's a Satellite Pro because he says on this subject on the front, but I was wondering if a new body what was wrong with it when I type fast, it hit stop or it goes to what I have already written and write half of the senses, although he. Anyo

  • Problem with the Acer, c/o Windows 7 laptop installed with the loading games

    I'm having a problem with Windows 7 which is preinstalled on a laptop Acer Aspire. Unless the laptop is on battery to 100% or pluged, games does not load upward. Because it is preinstalled serial numbers are not match so I can't get help from M/S.  A

  • small amount of soup at the event, display problem

    Small amount of soup contacted the side of my laptop, where evacuation, the laptop has flashed blue waves. Sometimes, it works very well but most of the time, it flashes waves blue and sometimes black or gray rest until never. Help, please

  • E1550 sees no USB storage drive

    I had a Toshiba HDD (1 TB) connected to my E1550. 8 months that the reader has twice had a problem with being able to save/replace the files after he successfully files for a period of time. Given that my storage device was not on the list of "approv