Tecra M9: Does not start at the local network after the value of BIOS password.

Hi all, I have configured a supervisor BIOS password on a number of Tecra M9s but later found that this does not allow books to be PXE started - and a number of them require now that rebuild.

I tried pressing the cursor keys in the first screen flash "Toshiba" (with the device down icons), but this will not allow to select the boot device - it's as if the keys are not pressed.

I also tried to get into the BIOS to change boot device priorities, but I can't just to get into the BIOS in a limited form - there is no prompt to enter BIOS password.

In brief - how can I work around this? -J' I need to know how to get the BIOS to ask the supervisor password (pressing ESC then F1 at boot only gives me the 'limited' BIOS)... Or, how to get the laptop for a PXE boot with a BIOS supervisor password.

Thanks in advance.

Advertisement

Hello

I would recommend pressing the F12 key, immediately after that the laptop has been powered.
This would allow the start on-screen menu.

Then choose the HARD drive as the boot source.
Then you could boot into the operating system and could use the Toshiba HWSetup to clear the supervisor password.

I guess the password is known to you

Tags: Toshiba

Similar Questions

  • Tecra S3 does not start when the multimedia center of Toshiba is connected

    Whenever I (re) start my Tecra S3 with the powered gigastore on (which is connected to the Media Center which is connected again to my dock via USB), my laptop only shows me the "toshiba" screen and doe not continues the start unless I turned off the gigastore and restart the laptop.

    What can I do?

    The same thing happened on my laptop while my external USB printer is connected to the computer. It has something to do with the BIOS.
    Hmmm, you can try to change the boot order in the BISO. Probably, it helps.

    I was an unlucky boy because the change of the boot order has not improved the situation. I had to unplug the printer or turn off the printer during the start-up procedure.

  • Tecra 8200 does not start with the new memory module

    Hi, ive just rode this memory to my willingness to .it tecra 8200 not initialize the message comes up / remove the incompatible memory in B / someone knows why?

    Memory for laptop IBM 256 MB PC100 144 pin SDRAM SODIMM

    IBM FRU L 33, 3070, 256 MB PC100, SDRAM SODIMM, no parity, 3.3 volts, 144 pins, 32 MB x 64

    Thanks for the replies biff

    Hello

    Well, I really put t know why this message occurs. It seems that this module must be compatible with your device. Are you sure that the module has no fault?
    Have you tried to use this memory module in Bank?

    Otherwise I found other compatible memory modules.

    PC100 256 MB (PA3069U - 1 M 25)
    PC100 128 MB (PA3005U)
    PC100 64 MB (PA3004U)

    http://www.frontline.co.UK/product_detail.aspx?pid=MEMKNG5662

    Good bye

  • Tecra M2 does not start - the power light AC blinking orange

    Someone at - it a list of codes for the Tecra M2 flash.
    My friend has a laptop that does not start at the top. the AC power LED flashes orange. a long, short, long, short, long, short, long, short.

    I checked the battery and reinstall the RAM.
    Any IDE?

    Hello

    I agree with go.
    The ASP would be able to tell what means error.

    Usually means short and 1 long: 0
    So the error must be: 1010 1010
    Due to the last significant bit (LSB), to be read by behind:
    So it now means: * 0101 0101 binary *-> it must be converted to hexadecimal-> * 55 Hex *.

    Then, you will get a hex code.
    But unfortunately, I m not very well which could mean this code

    So ask ASP for help!

  • Tecra M2 does not start successfully - zeroes appear all over the screen

    Help!

    My Tecra M2 does not start. After the toshiba logo, a series of zeros (0) appear all over the screen.

    -suspect it is caused by a virus, I formatted the HD (in another PC), but still the zeros appear
    -I might want to start in the DVD player, it seems to read the disc, but nothing happens, just a cursor flashing at the top left of the screen
    -J' I reset / replaced the RAM, but still no effect.
    -the power button works, lights and shuts the laptop but does not start.
    -CPU fan works
    -LED indicators of work are power, battery, dvd, wireless. Does not have HD LED light on.

    Any suggestions on how to solve this problem is greatly appreciated.
    See you soon!

    Hello

    I think we can exclude HARD disk failure because you are able to format it in another computer.
    As you suggest the RAM modules has been replaced but the problem persists
    So in my opinion, a motherboard problem would be possible

    But as you know, it of really difficult to say what might be exactly wrong
    I think that the technician should check the laptop then it would be possible to say what part is malfunctioning

    In any case, I think a motherboard might be affected

  • Why Tecra A3 does not start from CD/DVD?

    My laptop Tecra A3 does not react to the BIOS setting asking at the start of the CD/DVD.

    CD/DVD is the first place in the list of bootable devices (defined through F12 in boot sequence) the operating system starts with the HD. I have a chance to start with a bootable CD!

    The configuration is the following:

    Tip: TOSHIBA EAT10/EAT20
    BIOS: TOSHIBA V2.80 10/25/2006

    Any advice is welcome!

    Thanks in advance

    Antonio Giarrusso

    Have you tested with different CD bootable?
    Also try to start computer laptop using F12 and choose ODD as the first boot device.

    You can use ODD in Windows OS preinstalled?

  • Mac does not start and the fans going crazy

    Computer does not start and the fans work hard and fast. Someone has an idea what is the problem and how can I solve this problem?

    OLA I will try help EU tenho um macbook pro, mas esse problema não me it happened ainda EU acho seria o seu mac origem help esse problema pode formatar better.

    SE nao tem'm ligar o seu osx para formatar use cmd + r e ligar pressionar cmd + r ele deve AI PODES ligar restore o seu novo osx.

  • Satellite Pro L300-21F does not start and the screen remains blank

    L300-21F is aged 18 months, so out of warranty. When you press the power button, you can hear the fan and a "click" but the hard drive does not start and the screen remains blank. The power and the battery on the headlight LEDs, but the switch light does not work. I checked the power supply and it is 19.3V and substituted a good known. Removed the battery, tried with just the power cord and still nothing. Pressing ESC or F2 when you press the button power does not bring to the top of the screen of the bios or any other message. I have concluded there is no power the jury. A friend he had its technology take a look and he concluded Council is probably a friend.

    So my questions are:
    1. He's probably right?
    2. is it a common problem with an easy solution?
    3. what else can do before shelling out for a new Board of Directors?
    4. is there a link where I can find how to disassemble the case?

    Any help appreciated

    Hello

    > 1. He's probably right?

    Yes, it looks like motherboard failure

    > 2. Is this a common problem with an easy solution?

    If it's a motherboard problem, the whole motherboard is replaced. Quite expensive part...

    > 3. What else can do before shelling out for a new Board of Directors?

    I don't think you can do anything with fried mobo

    > 4. Is there a link where I can find how to disassemble the case?

    Take a look at the site called irisvista.com

  • I want to install WIN 7 on my Dell XP computer. The disc I bought says that the hardsrive must be clean first. The disc does not start on the existing XP. How can I do this?

    I want to install WIN 7 on my Dell XP computer. The disc I bought says that the hard disk must be clean first. The disc does not start on the existing XP. How can I do this?

    Hello

    Have you changed the boot order?

    You need to change the Boot order to make the DVD/CD drive 1st in the boot order and boot from the Windows 7 DVD:

    How to change the Boot order in BIOS:

    http://pcsupport.about.com/od/fixtheproblem/SS/bootorderchange.htm

    Do install a cleaning, removal of the existing XP partition and create a new partition to install 7 on in the own installation process:

    http://www.SevenForums.com/tutorials/1649-clean-install-Windows-7-a.html

    See you soon.

  • My pc says that windows does not start because the following file is missing or corrupt: \WINDOWS\SYSTEM32\CONFIG\SYSTEM.

    My pc says that windows does not start because the following file is missing or corrupt: \WINDOWS\SYSTEM32\CONFIG\SYSTEM. It is said it can be repaired by using the original installation CD, but we do not have. Any ideas please?

    The file is missing or corrupt is one of your files in the system registry.

    By far, the best way to recover from this is to go to another computer and create a free Hirens Boot CD.
    Download Hirens: <> http://www.hirensbootcd.org/download/ > (link at the bottom of the icon of the disk)
    Hirens CD burning <> http://www.hirensbootcd.org/burning/ >

    Once you create the CD, and then start your system of problem with this CD.  In the first window, select "Mini Windows XP" and wait for the system to start.  When it starts, go to the Hirens Boot CD menu and select
    Register-> Registry Restore Wizard.
    then follow the prompts.  This wizard will return a copy of your registry database from backups that are stored with your system restore points.  After the restoration, stop, remove the CD and restart.

    When you start your system, it is recommended to perform a system restore operation to ensure the consistency of your system
    "How to restore Windows XP to a previous state"
       <>http://support.Microsoft.com/kb/306084 >

    Also, this error is almost always accompanied, if not caused, the corruption of the file system.  Also a good idea to perform a check disk (chkdsk) operation with the option "repair".
    "How to perform disk error in Windows XP check"
       <>http://support.Microsoft.com/kb/315265 >

    The hard way to get back is covered in the following Microsoft KB article, but if you have installed a large number of service packs for your installation of XP, I don't give you many chances to get past part 1. (And there's also an installation CD to access the Recovery Console)

    "How do I recover from a corrupted registry that prevents Windows XP boot"
      <>http://support.Microsoft.com/kb/307545 >

    HTH,
    JW

  • Problems with my installation of Windows XP and my computer does not start on the CD.

    Hi, I need BIG help here please!... I wanted to do a fresh install of Win XP Pro, but my PC didn't boot from the XP CD... I changed the BIOS settings, the sequence start on CD, restart my PC and he kept boot from the HARD drive and the PC does not recognize that there is a CD-ROM drive. Once the start-up of the PC from the CD, I wanted to delete the partition and format the HARD drive, but it says "Setup could not format the partition...". "something like that... so what I did I have the PC from the boot CD, click in the command line and 'R' for repair, I wrote"format c:"and after that, I wrote" diskpart remove C:' so I deleted the old partition, create a new and when I wanted to install XP on it, I could not because the PC does not start from the CD... how can solve this? "

    Thank you!

    original title: HELP for the installation of Win XP.

    Hi Jorge,.

    So the only thing I can think is that it is a sort of master/slave thing.

    Your IDE HDD will be a Knight, probably alongside where the power cable is inserted, to dictate whether the player will be considered to be a master, slave, or cable select. Assuming that it is the only HARD drive in the PC, make sure it is designated "master". Then, in the BIOS, make sure that the boot order is specified as HDD0 first (as opposed to HDDx where x is greater than zero).

    In addition, assuming that the data cable is the new type of Ribbon with strands of 80, make sure that the blue connector of the IDE data cable is in the motherboard and that the end of the black connector is in the HARD disk and, if it is a two-disc data cable, do not use the gray connector.

    Tricky

  • XP Home Edition does not start without the installation CD after reinstall.

    I reinstalled XP Home Edition on my PC without formatting the drive first in order to keep all of my data.  I have installed all service packs.  However, for some reason, I had to call Microsoft to get validated.  The only problem I have now is that it does not start without the installation CD in the drive.  I have XP on the half before the C drive and me on the back of half.  The reader is a digital WD800JBRTL of Western.  Well it worked like that for years. Why can I now not start without the CD?

    HiNeal2660,

    It seems that the NTLDR file is not on the C: drive. NTLDR is the boot loader for all versions of Windows.

    You can perform a Windows XP repair installation & check if you are able to start normally.

    For more information, please visit this link: perform a repair Installation

    Hope the helps of information. Please post back and we do know.

    Concerning
    Joel S
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • I just installed a SSHD and cloned my old SATA HDD through him. My CC 2015 apps work okay but the creative cloud app does not start. The circle of rotation right guard go. What should I do?

    I just installed a SSHD and cloned my old SATA HDD through him. My CC 2015 (Photoshop and Lightroom) apps work okay but creative application cloud does not start. The circle of rotation right guard go. What should I do?

    Sorry to have troubled you. I rebooted and everything works now.

  • Tecra 8000 does not start after the BIOS update

    From one day to the other does not start my Tecra 8000 (400 MHz/256 MB BIOS 9.30 for years). After start-up, the disc starts to turn, but the screen including the backlight remains completely black, without red logo TOSHIBA BIOS is not accessible.

    I got a new mainboard on stock, so I replaced it, and it worked. Unfortunately now my WLAN card now did not work properly. I tried several settings of the BIOS with no results, so I decided to do an update of the BIOS from 7.50 to 9: 30. After the upgrade, I get the message "ROM WRITE successful, utility completed. LEADER BIOS: Tecra8000 v 9,30 ". Because what either kept silent, I pressed the power button to restart and heard a long and many short beeps (endless). I could interrupt what pressing the powerbutton for 5s.

    After turning on again I have the same problem as described in the first line :-( I can't get into the BIOS, but I can again update (with pressed F12). Once again these beeps.

    What to do with these beeps after average BIOS update? I replaced the MoBo connector LED with pension. Processor, memory, keyboard and HD has remained the same. So, before I start disassembling the machine, please notify, your help is very appreciated.

    Hello Joachim

    I'm not a technician and don t know what the beeps but I am afraid that the BIOS chip is damaged. Because of this, the unit is completely dead. Sorry, but I really don t believe you can do anything. Maybe the new motherboard again :(

  • After the motherboard replacement Tecra S2 does not start

    Hello

    I replaced the motherboard in my Tecra S2 and now it does not start, the power light is on but nothing on the screen. I can hear the h/d running DVD lights.
    I tried to remove the RAM.
    Also checked the CPU and still nothing.

    NEED HELP.

    Are you sure that the display is OK and correctly connected?
    Is busy, I mean drive HARD HDD LED flashes?

Maybe you are looking for