Tecra S3 - HDD was not detected during the intallation of win7

Similar Questions

• Media information was not found during the rip?

  Recently it started to happen. The information is not being downloaded. None of this. Am online during extraction is performed.

  Has he started recently?
  If so, you can try using System Restore to when it was working properly.

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-system-restore

  Alternatively, you can try to manually update the information manually and see if it works.
  http://Windows.Microsoft.com/en-us/Windows-Vista/add-or-edit-media-information-in-Windows-Media-Player

• Add a homegroup password after that put Windows in place is over and a password was not entered during the set up process

  Hello

  I had a hard drive crash and had a new hard drive installed.  At the end of the recovery process, I was asked to answer questions such as the choice of a language.  I also had the opportunity to put a password in a homegroup. Not entered a password.  BIG MISTAKE.  I can't reach my home group now because I do not have a password.  I don't have the ability to change the password that I never entered one in a first time.  Unless someone can help me, it seems that my only option is to make the process of recovery everywhere.  My concern, there is that I won't be able to download Microsoft Office almost again because it won't let me this time.  I activated once and he didn't allow me to activate again. But he did.  I think that he won't let me activate a third time.  Can someone tell me where I can go to add a password to my homegroup.  No help from HP or Microsoft Windows has been useful.  I have Microsoft Windows 7 Home Premium.

  Hi kschoff.

  
  Thanks for posting your query in Microsoft Community.
  
   
  From your description, I understand that you are unable to add a password for home group after that Windows set up was complete.
   
  I suggest you create a new group home and check.
  
  Follow the link that will help you create a new group of home.
  http://Windows.Microsoft.com/en-us/Windows/HomeGroup-help#HomeGroup-start-to-finish=Windows-7&V1H=win8tab1&V2H=win7tab1
  
  Hope the above information helps.
  Make it happen to us and made me know the status of your question so that I can fix it as soon as possible.

• Plustek OpticBook 3600 will not install error that an error occurred during the installation of the device. The required section was not found in the INF

  Original title: Plustek OpticBook 3600 is not installed

  Found new hardware wizard runs, but after scanning stops the disc from the manufacturer with the message ' year error occurred during the installation of the device.»  The required section was not found in the INF"

  PC system is homebuild which, in theory, exceed the minimum requirements of the system of manufacturers.  Operating system is Windows XP Pro with Service Pack 3.  The scanner is connected to the USB 2.0 card that is not separately powered, but installed in the PCI slot.  I suspect that the problem lies in the PC rather than the scanner. but do not know what the problem is.  Any help would be appreciated!

  Hello
  You can try the troubleshooting provided in the link below steps to fix the problem.

  You receive a "unable to install this hardware" or "an error has occurred during installation" error message when you try to install a PCI device

  http://support.Microsoft.com/kb/841567

  Note:

  To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows

  http://support.Microsoft.com/kb/322756

  See also:

  Error message: cannot install hardware. An error occurred during the Installation of the device

  http://support.Microsoft.com/kb/810882

• HARD drive not detected in the BIOS on Satellite A215

  Hi all

  I could use to solve this problem: bought this laptop computer without a disk of the auction. Installed again 2.5 inches HDD SATA 250 GB, which was not detected in BIOS and also not detected when using a MS Vista installation disc. When trying to install Vista, get a message no drive seen HARD and demand for pilots.
  I flashed the BIOS with version (2.0) of lates without problem through the CD drive, but still no detection of HARD drive.

  The drive partitioned and formatted NTFS without problem by using another computer and USB SATA adapter using the command line method. Just for additional verification, I went on the new HARD drive to an extra 2.5 "SATA HDD used for backups, but that the HARD drive has also not been detected.

  It is not a "compatibility" option in CMOS to select SATA or Auto, etc..
  There is not a second HDD, so this isn't a question of slave/primary. There are no jumpers on the new HARD drive.
  Set the CMOS settings 'by default' does not solve the problem.

  The SATA connectors on the HARD drive and laptop computer are in perfect condition.
  Also, the drive is not detected on the laptop connected via USB to SATA Adapter, but of course there is no OS installed to support this connection.

  In any case, I just can't come up with any more ideas to try.
  Any suggestions would be really appreciated!

  Best,
  Glenn

  Hello

  The BIOS should recognize the HARD disk even if the SATA mode would be compatible or AHCI. This should not affect the recognition of the HARD drive.

  You said that you have tested the condition of the HARD drive and it's ok, so I guess that it s no disc HARD question.
  Hmm, you could try to format the HARD drive once more and then connect the portable computer HARD drive.

  Another idea: Remove/Disconnect the CD/DVD drive and then connect the HARD drive to the SATA connector.
  If it does not, then I recommend to test another HARD drive, otherwise if the new HARD drive would not work, then a SATA controller may be defective.

• Satellite M30x + Win7: DVD not detected by the CD/DVD drive

  Hello

  I use a M30x since 2004 with its CD/DVD drive * a S mat. DVD-RAM UJ-831
  When I was with Windows XP, I have never had problems to read or write on CD, CD - R, DVD, DVD - R or DVD - RW. But recently I installed windows seven, and since that day the drive won't recognize the DVD. I can still read and burn CDs and CD - R. I'm burning the same Virgin DVD-+ R/RW as before, but the drive won't detect them. Those I have already burn are not detected or the other.
  My computer says that the CD/DVD drive work properly and drivers are up to date.
  I tried to clean the lens, but nothing has changed. And I tried to reinstall the drivers, but I could not found for windows seven.

  Thanks for the help.

  Hello

  Have you tried to delete the upper and lower registry Filters >
  Pleas check it!
  http://support.Microsoft.com/kb/270008/en-us

  You will find the registry key where filters must be removed.

• Application has failed to start because msa32dl was not found, reinstalling the application may fix the problem

  How can I fix it?
  application has failed to start because msa32dl was not found, reinstaling the application may fix the problem

  First make sure that your system is clean in:

  Download, install, update and scan with these full free malware detection programs:

  Malwarebytes (MMFA): http://malwarebytes.org/

  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/

  http://www.Microsoft.com/security/scanner/en-us/default.aspx Security Scanner   

  http://www.eset.com/us/online-scanner/ eset online scanner

  Then answer the following questions:

  brand and model of the pc

  current antivirus

  Operating system and service pack

  What application fails to start?

• HP X 360: hardware virtualization enabled in the BIOS but not detected by the installation of Intelhaxm.exe

  Hi all

  I'm trying to get Android studio works on my 360. Everything is fine until you try to run virtual device/emulator.

  This does not work because the Virtual Machine is required. When I looked in the BIOS I was surprised to see this small handbook has the functionality that has been disabled.

  I now activated but still not detected by the software. Can anyone help with this?

  See you soon

  The problem was Avast antivirus. I uninstalled and hey presto, intelhax went very well.

• Video card GeForce GTX 660 not detected by the motherboard Windows 7

  I recently upgraded my PC with an Asus z97 - a motherboard and processor Intel i5 4. After the reinstallation of Windows 7, I was able to get a signal from my video card 660 geforce gtx for a few hours. After Windows install several updates, however, I am unable to use my video card without receiving an ENTRY NOT FOUND both of my monitors. My video card is also not appearing in Manager devices, or BIOS and use rather Intel HD Graphics. Cause of the undetected video card, I am unable to install the latest drivers for my card and I have no idea what to try next. I also made sure my current diet provides enough power for the card. Is powered without a doubt the map because the fans spinning, I'm positive that I've attached all required power cables, and the card is inserted completely into the motherboard. I tried all PCI-E ports in my motherboard, but it continues to not display. I tried to install the drivers manually, but the video card should be detected before this is possible. Any help would be greatly appreciated.

  My specs:

  ASUS card mother Z97 - A

  Videocard GeForce GTX 660

  Intel i5 processor 4

  8 GB RAM

  700W ATX power supply

  I should point out that I have tried almost every technical troubleshooting that I have met, with the exception of disabling Intel HD Graphics. I fear that if, due to there not being any trace of my video card in the BIOS and Device Manager, if I disable this will also lose signal from the motherboard of DVI and HDMI, ports that are what I currently use.

  Hello

  As the graphics card is not detected by the motherboard, you will need to contact Asus for more help on this issue. You will need to check if the graphics card is detected in the BIOS or not, if not then contact the computer manufacturer is the right point of support.

  Support from Asus: http://www.support.asus.com/

  Please do not hesitate to visit our Web site for any help with the Windows operating system.

• "Setup could not detect all the printers.

  I've recently set up a new computer and the network.  The host computer is running Vista.  I have connected a Deskjet 6940 via an ethernet cable into the Linksys router and can print from the host computer.

  I have a laptop which is under XP Pro, and who has a connection with the network.  I downloaded the driver from HP on the laptop to try to connect with the 6940, but during the install process, I get the message "Printer not found - Setup could not detect all the printers on the network."

  Firewalls on both computers is disabled.

  When I type the IP address in the address of the host computer or on the portable bar, I page of the printer, including its SSID.

  I tried to type the IP address in the field suitable for the installation of HP on the portable routine, however and always got the "printer not found."

  Ideas?  TIA

  The Deskjet 6940 being on the network, we will try to add the printer manually. Here is the sequence to XP:

  1. Click on the button 'Start'--> Printers and fax machines.
  2. Under print jobs, click on "Add Printer".
  3. Click 'Next' in the Add Printer Wizard window.
  4. Select " printer local to this computer. Deselect "automatically detect and install my Plug and play printer." Click "next".
  5. Under Select a printer Port option, select "Create a new port" and choose "Standard TCP/IP Port" and click "Next".
  6. In the "Welcome to the Add Standard TCP/IP printer port Wizard" make sure that the printer is turned on and connected to the same network that your computer is connected to. click on the button "next".
  7. Under "Add Standard TCP/IP printer Port", enter the host name of the printer . You can also use the IP address of the printer if it is static. Click 'Next' and then click 'Finish '.
  8. Now, select HP in the manufacturers list, select your printer from the printer model list and click the button "next".
  9. If you can't find your printer, you will need to find the installation CD and use the 'Disc' option to select one of the files hp*.ini. You can also select another model of the same type HP printer.
  10. Add the name of print spooler and click on "next".
  11. Click "next".
  12. Click "Next" and "Finish."

• iCloud backup after iOS 10 - some files were not available during the last backup

  HI - we are a company with about 350 users of iPhone and iPad.  I put this in the iCloud in the community section, but I've seen other users have the same problem in this section, so I thought I would add here.

  In order to stop users add their own e-mail accounts on the iPhone that lock us the device through restrictions - deactivation of the accounts section.  It stops and then access the iTunes settings.  In the test of iOS 10.0.1, we have one of the devices (a 16 GB 5 s, who had been a backup at 7:20 that morning), improved 9.3.2 that went well with no obvious problems, then, after a few days to leave the handset to the function, we have lifted the restriction and the backup on iCloud to find any backup not occurred since the upgrade and a message 'some files were not available during the last. backup"in its place.

  If all our staff upgrade their phones (we gave says not yet) then the backups look like they stop.  It is easy to fix, as a manual backup, will complete the process, but you have to remove the restriction to do this.

  We tested on iPhone 5, 5 s, air iPad iOS 8 to 9.3.5 and all have this problem.

  I have exactly the same problem, 16 GB iPhone 5s as well. I plan on raising at my Genius Bar appointment today.

• Satellite U500 - 1 DR series Notebook is not detected by the TOSHIBA site

  Hey,.

  My Toshiba Satellite U500 - 1DR Series notebook (Serial No. 1A058758R) is not detected by the automatic detection of TOSHIBA online system. When trying to get portable detected manually on the site, I stopped fingd the model (Satellite U500-1 DR) is listed in the list of available templates or models. I'm unable to download software/updates on the site.

  Hello

  If the work of autoetection doesn t you can find manually but not not using the name model but the model reference number. Your DR U500-1 has part number PSU9ME-xxxxx then please check under http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp Toshiba download page and look for Satellite U500 with reference number or model number short PSU9ME.

  Can find you it?

• niDMM.cs exception: "the device was not recognized. The device is not supported with this driver or version. »

  Hi all!

  I have a question about using a DMM (PXI-4065) with VStudio 2008 and Measurement Studio 2009.

  Because DMM are not always supported in .net, I downloaded niDMM.cs 3.0 wrapper of the web site of NOR.

  I also downloaded example c# measure DC Voltsto compare with my request.

  Both an example and my application fail trowing the exception [-1074118656] 'the device was not recognized.  The device is not supported with this driver or version. " class constructor is called.

  DMM = new InstrumentDriverInterop.Ivi.nidmm ("PXI3::12:INSTR", true, true);

  I guess it is function of device PXI!

  I also tried to use a VISA alias as "pippo" and then I tried to insert a device unexistent name. In any case the same exception was trown.

  NOR-DAQmx 8.9.5

  NOR-DMM 3.0.1

  NI-VISA 4.6.1

  NOR-MAX 4.6.2f1

  Roberto

  Hello Robson,

  Maybe you areusing an incorrect descriptor itrument, try please the instructions contained in the following document:

  KB 33A96PCW: receive error-1074118656 when running OR DMM screws

  Let me know if this might help.

  Best regards.

• Digital mp3 player is not detected on the computer.

  Original title: my phone dosnt recognize my drive digital mp3. When I plug it into the usb port do not get an icon. so I can't load music can help you

  MY LAPTOP DOES NOT RECOGNIZE MY MP3 DIGITAL PLAYER. WHEN I PLUG IT INTO THE USB PORT I DON'T GET THE USUAL ICON. SO I CAN'T DOWNLOAD MUSIC ON IT. CAN YOU HELP ME PLEASE

  Hello

  Thanks for posting your question in the Microsoft Community Forums!

  If I understand the question, digital mp3 player is not detected on the computer. Please let me know if this is not correct.

  Before I continue with the troubleshooting steps I may need a few more details to better understand the issue.
  1. what operating system do you use?
  2. do you receive any error messages?
  3. are you having the same problem with other USB devices?
  4. have you tried plugging the machine into the other USB Ports?
  5. did you of recent changes on the computer before this problem?
  6. What is the serial number and model of the MP3 player?
  Method 1:
  We will first try to plug in other USB Ports and on another computer to make sure that there is no problem with the digital mp3 player.
  Method 2:
  If the first method does not resolve the problem, run the hardware and devices Troubleshooter and check if it helps.
  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/mats/hardware_device_problems/en-us
  For more information, please see the link.
  Tips for solving problems of USB devices
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices
  Respond with the required information so that we can help you solve the problem.

• DVD rom not detected in the Bios & windows

  Mr President, in my computer the dvd rom is not detected in the Bios & windows. Send me a PSE with solution please.

  Hello

  1. which version of the windows operating system is installed in the computer?

  2. What is the brand and model of the computer?

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/982116

  Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756

  (http://support.microsoft.com/kb/322756/)

  How to back up and restore the registry in Windows

  I also suggest you to connect with the computer manufacturing and update drivers for BIOS.