Tecra S5 - Docking Station Drivers

Similar Questions

• Tecra 8200 docking station

  Hello @ all!

  I have a Tecra 8200 laptop computer and want to install a Docking Station.

  I built everything in.

  But I had a big problem:

  When I take the laptop in docking station that has contact with the Docking Station, the laptop can not find a PCI driver. I can't find this driver Notebook searches. I had installed all the drivers that was available on the Toshiba site.
  But I got the same research memoire.esolutionle Nooteboom PCI card unknown that AIDA can not find.
  And the Nooteboom cannot find the Epansion Station

  The next problem is when I take an E-station IDE cable in a drive hard or on a cdrom drive, it curbs the power for this hardwareparts.

  Could someone help me?
  Thank you

  PS: Excuse my bad English

  Hello

  you have the 1DST PA3018E? It won't be back with the PA3017E Docking Station/Port Replicator.

  Stefan

• Tecra 8100: Docking Station: Notebook reset when you try to burn DVDs

  System: Toshiba Tecra 8100 + Replicator port
  PA3017E + Expansion Station PA3018E,
  Samsung DVD Burner H552B (new firmware) built in (docking station).

  Problem: If I try to burn a dvd/CD, the system performs a hard reset and is inexplicable.

  What could be?

  Hello Stefan

  It's not easy to say why but maybe sometimes it s a burning question of the software?
  Have you tried using different burning software?
  I recommend to check if this problem occurs with different burning software.

  Best regards

• Tecra M5 docking station problems

  Hello

  I don't know if this has happened elsewhere, but my Tecra M5 (Win XP / SP 3 / fully updated on MS) boots when undocked, but hangs on the appearance of the first "Loading Windows" screen Re-booting subsequently always results in the typical menu with SafeMode etc... My amateur solution is to start offline and then just plug it in, but my logic suggests that this may not be the right solution. I have run the reinstallation CD and completely re-formatted the system twice, but anything will do. I'd appreciate more ideas... Thank you & best wishes

  Richard Taylor

  Hello

  As far as I know original Toshiba recovery image is WXP SP2 only. Am I right about that?
  This happens immediately after the clean operating system installation or after the installation of SP3?

  Recovery image has been tested with docking option and it should work. I think it's a problem with SP3 which can have a negative influence on demand for mobile extension. This application is responsible for the own berthing and departure procedure.

• Using ISA cards in the Tecra 8100/8200 docking station

  Is it possible to use old pc ISA cards in the PCI slots in the Tecra 8100 docking station?
  The Deskstation V Plus for the 8000 series seems to allow dual use in some of its slots so I wonder if it's the same for the 8100/8200 series.

  You can also the Tecra 8100 can be anchored to the Deskstation V to allow access to the ISA slots?

  Hello

  where did you get this with the AIS in the PCI slots? I've never seen a combo slot in my life so I can't believe :)
  But what about the v: Deskstation

  Yes, it can be anchored, it s integrates without problems, then you will be able to use the ISA-machines built slot.

  Welcome them

• Tecra 720cdt: screen is central docking station - 1/2 in.

  Hello

  Ive just took a Tecra 720cdt with docking station, when the 720 is on display of the battery is ok, when the screen docking station is central 1/2 in. I downloaded drivers but how and what driver do I need to use to reset the docking station for produce size full screen?

  Thank you.

  Windy morning

  As far as I know if you use the right display driver should not be a problem. As far as I know, this unit comes with Win 95 and you can find the right driver on the Toshiba download page. What operating system is running on your device?

  Check also displays the properties on the settings tab.

  Good bye

• The docking station uses Henge drivers?

  Is the Henge dock just a cable Organizer? -Seems all that is material.

  Or I need specific SOFTWARE drivers so that my Henge Dock to exploit 100% as expected?

  I use the Version B Henge Dock for my MacBook Pro 17-inch - and it all works when it is plugged.

  I just want to know if I'm missing out on something?

  THX

  Henge Docks are just a docking station, no software required, and any other features. Make sure to work your hard MBP while closed but, I think that life has been shortened on my Macbook, because it has been used mainly in the dock and couldn't cool properly with the lid closed all the time. The logic board failure.

• Tecra M11 - 17V - identify the serial port on the docking station

  I have a laptop Toshiba Tecra M11 - 17V, which I often use with the docking station that accompanies it.
  There is a DB9 serial port at the back of the docking station, but I don't know what COM Port.

  I use Windows 7.

  In the device, COM9 Manager - COM22 are identified as Port BT (bluetooth). Com7 - COM8 are RIM Virtual Serial Port v2, COM17 is Prolific USB-to-Serial Comm Port and COM18 is USB-Serial CH340.

  I thought that COM17 or COM18 were the most likely candidates, but have not been able to get to answer using one of them.

  I connect a Psion 5 (Comms app) to him and have developed ports and the Psion 8bits, 19200 baud, no parity, 1 stop bit.

  Hello

  > There is a serial port DB9 on the back of the docking station, but I don't know what COM Port, it is

  I think you have misunderstood something wrong
  COM ports in Device Manager are virtual com ports
  There is no link between a serial port and a virtual com port.

  I have a question: what docking station you have exactly?

  I had an express port replicator and this device required an additional serial port driver installation.

• Tecra A10 - 1GV and Docking Stations: Dynadock vs Express Port Replicator II

  Hello Forum;

  Official Toshiba site proposes to use the Docking Station Express Port Replicator II for laptop A10 1GV.

  I need for my construction work 2 monitors.

  My question: can I use with the Express Port Replicator II two additional monitors at the same time (there are 2 connectors (DVI and analog VGA/RGB). Is it possible to create two different images in this way?
  Some have said, that after a connection with the DVI - D VGA connector is turned off.

  Someone at - he experiences?

  On the other hand Toshiba offeres the Docking-station "Port replicator USB Dynadock U" -.
  This docking station is only connected via USB with the laptop. According to the data sheet - it provides an analog and a digital monitor with different views at the same time, up to 1920 x 1200 pix., extra headphones and 6 x USB 2.0. more network connection

  This official docking station works with all USB-connect computers, but in the compatibility list does not mention the Terca A10 and gives only a declaration of compatibility for the series Toshiba NB200 from Toshiba.

  Someone out there experimenting with this docking station?

  What would be the best way to work with two monitors + the computer screen?

  Thanks for all the good advice.

  Michael

  Hello

  As much as I know Express Port Replicator supports the simultaneous use of RGB & DVI only if the laptop itself also supports the simultaneous use of RGB & DVI.
  So if the Tecra A10 1GV would support the use of RGB and DVI port simultaneously then Express Port Replicator should support too.

  The Port USB Dynadock Port Replicator support VGA or DVI port. I didn't find the Dynadock, which was equipped with two ports together.
  The Dynadock can be connected to all computers with USB 2.0 and it beautiful s expansion.

• Tecra M9 - save the settings of display with docking station

  Hey there.

  I have a user who has a Tecra M9 on a docking station.
  There are 2 monitors connected to the docking station with VGA, the other with DVI. I use the Nvidia Control Panel and configure the screens and all is good in the world.
  That is until the user off the laptop, some work at home, then puts the laptop in.

  Therefore, only one monitor works, with the second out of action.
  I can go back and reset the configuration, but the user does not want that to happen every day.

  Any suggestions on how to get the laptop to save your setting as the case not docked or anchored?

  Thank you!

  > That is, until the user off the laptop, work at home, then puts the laptop in.
  Do you know what the user did in the past?
  To my knowledge there is not any special options that could save it. If you click on the button (apply) the changes are made and recorded.

• Tecra M9-104 with docking station - DVI resolution

  I wonder if anyone can help. I have a Tecra M9 - 104 running Windows XP. I also have the docking station to go with it. The great thing about the docking station, it's that it can out to two screens as the port on my M5 Replicator could not do.

  I bought two identical external screens that have a native resolution of 1440 x 900. I went into the Nvidia display configuration and set up to display both (one is plugged in VGA and one DVI port). However, the display on the DVI monitor is wrong. After further investigation I woke up the menu of the monitor on the screen to see that the resolution actually be issued is 1280 X 1024, despite Nvidia screen saying 1440 x 900 has been the output. Whatever I do, I can't increase the resolution on DVI port.

  The only thing I could find on Google and these support forums is that the maximum resolution on the DVI port on a port replicator is 1280 x 1024, but it was for the M1 and M2 series. This laptop is the last series and as such, I expected that the spec had been updated at this time.

  Someone at - it ideas?

  Could be due to a limitation of the video driver on the laptop, or you can try to download a utility that requires to use a different resolution, its called Powerstrip (do not have a download link sorry).

  Be careful with it though, you can mess up your video driver

• Tecra M2 not to close on docking station

  I have a Tecra M2, of which most of the time is used in a docking station. However if I'm on the docking station for laptop computer does not shut down (it sticks to the "Windows is shutting down" screen... unless I have physically remove the laptop from the docking station, and then he finished the process to close.)

  If the laptop is not on the docking station, there is no problem of closure.

  I tried to remove all the devices that are connected to the docking station, but that makes no difference.

  I use v3.65.00.XP Toshiba Mobile Extension.

  Also note that I do not and never have been, a 'disconnect the computer' as an element of Start Menu (there also no "NoStartMenuEjectPC" button anywhere in the registry.

  One last thing; If the laptop is cold (IE only used for a few minutes), then it will sometimes close ok on the docking station.

  Any suggestions very welcome.

  Tennant

  Hello

  It is not easy to give you a good explanation, but you can try to reinstall the mail Mobile Toshiba is perhaps also an application that runs in the background, the reason for this.

  Your device comes preinstalled with recovery DVDs?

• Docking station for Tecra M5

  If there is a docking station (universal or special) for Tecra M5 laptop computers?

  Rgds

  Hey

  What do you think of a Dynadock?
  There's a Dynadock who takes in charge a VGA (PA3541E-2PRP) or DVI (PA3542E-2PRP) port.

  Otherwise I recommend to use an Advanced Port Replicator III more PA3474E-1PRP which is compatible with the Tecra M5.

  Google just for the part number and you will get some info on the Advanced Port Replicator III more

  Welcome them

• Tecra M10 - 17 H no support DVI via docking station not

  There is already a message asking this, but I wanted to point out that it is a problem affecting more than one user.

  Too, I bought a Toshiba laptop for my business as it was supposed to be a laptop a serious matter. However, I must say that I am losing confidence that Toshiba understands what needs a company.

  The docking station is frankly a joke. USB KVM will not work with it, probably, there is no PS2 port you can not use a KVM PS2 instead. Even if you could, the VGA dock does not detect the external VGA is present when there is a KVM. Of course, the answer is "simply" open up the laptop and set it up on the Panel, then switch to external whenever you turn it on. How can anyone think that is a response in a business, or any other environment is beyond me.

  Now, I find that my laptop has an Intel graphics card I can't use the DVI port on the dock either. Which is really annoying, is that I could buy a laptop at half price, but wouldn't because I wanted a laptop class business that disintegrates not in respect of the use. I didn't pursue a fantastic graphic option because I did not doing anything fancy either, but graphics without the supported DVI via the dock is just simply ridiculous.

  Now, I regret bitterly, to get rid of the old Dell D/Dock that although several years worked without fault and with DVI, with any old KVM and without any problems at all.

  Sorry for the mug shot, but I am bitterly disappointed that I bought a cheap puppy that I can't afford to write off for a good while yet. Meanwhile despite works well when it works, the laptop is a right royal pain to use when the dock is therefore unnecessary.

  What to tell boyfriend
  Is a really nice laptop Tecra M10 and Portégé series and series Tecra laptop computers Bussines there.

  But it seems that the DVI port on the Port Replicator Port Express is supported only on computers with ATI graphics card or nVidia.

  I found this Toshiba document:
  http://APS2.toshiba-tro.de/KB0/TSB7B0201000CR01.htm

  It s on Tecra A9 but maybe that it s a Tecra M10-related too

• Tecra S10: What Docking Station should I use?

  My boss got a notebook S10-106 of the headquarters and would like to buy a docking station for this, please advise what compatible docking station.

  Thank you much in advance.

  Best regards
  Celia

  Hi mate

  I googled a bit and found information on the compatible ports replicators;
  You can use the Port Replicator II.
  It should be compatible with the Tecra S10.

  See you soon