Tecra T9100: To do wireless with WPA

Hello
I would like to take part in our wireless LAN. But it is necessary to have the WPA or WPA2. You have information, where can I find a driver for my laptop Tecra T9100 wlan?

Hello

Unfortunately, the new WLan driver will not solve your problem.
The cipher mode is dependent on hardware (card) and not the software (driver)
In this case if you want to connect the unit to the WLan with WPA encryption, you must use a new wireless network or WLan USB stick map
.

Tags: Toshiba

Similar Questions

  • SONY VAIO VGN-SZ28 cannot connect wireless with WPA encryption

    Hi guys

    I have a sony VAIO PC is unable to connect wireless if I have WPA and WPA2 encryption. When I decrease the security WEP device connects well. the laptop never asks the user name and password of the ad

    The type of security, I use WPA2 802. 1 x with PEAP-EAP-MSCHAPv2

    Please note the following:

    1. Wireless driver is updated to the latest version. I see EAP and WPA Press Cordless screwdriver
    2. Windows XP service pack 3 operating system

    no idea why I am facing this problem?

    Thank you very much

    Elijah

    Hi Elijah

    You can deal with a number of certificate on the laptop.

    If the wireless client is configured to use PEAP Protocol as you suggested the default setting is usually to check the certificate of the server. This would mean that you need to install a certificate on the laptop. However, there should be a setting on the client to disable the server certificate 'validate' If you do not want to (or cannot) to install a certificate on the laptop.

    See attached some screenshots.

    Concerning

    Roger

  • Access wifi with WPA encryption Vista giving "access: Local only.

    I've read many threads on a similar situation. I am convinced that the symptom has many different causes. Nothing I've read solves the problem for me.

    I have toshiba vista laptop and struggled until I've decided to return to the original recovery disk from the manufacturer, reloading everything from scratch. still did not help. The use of WEP encryption works, so I don't know the interface wireless on the laptop works. but it is not acceptable that WEP is such a weak encryption - basically no security. try to use the encryption WPA or WPA2, which does not work for vista. laptop is a few feet from the router, so a lot of signal strength. one other non-Vista computer laptop works well. uninstalled the trial version of mcAfee. updated the drivers and software vista for later. assign an ip address to the laptop, and when it starts up, I see that this address is assigned. Disable all the ipv6. disabled the DHCP broadcast stuff. off the vista firewall.  ipconfig/all is shown below, which seems ok to me. never had Norton or symantic is installed. tried to reset the ip stack. Wired ethernet to the router works. just to get the local access only on the wireless with WPA encryption. The router is quite new netgear WNR2000 and also tried a brand new netgear router multiband with identical results.

    Sure could use some help here.

    Windows IP configuration

    Name of the host...: FamilyComputer
    Primary Dns suffix...:
    Node... type: hybrid
    Active... IP routing: No.
    Active... proxy WINS: No.

    Wireless network connection Wireless LAN adapter:

    The connection-specific DNS suffix. :
    ... Description: Atheros AR5005G Wireless Network adapt
    Physical address.... : 00-16-E3-F2-DE-BB
    DHCP active...: No.
    Autoconfiguration enabled...: Yes
    IPv4 address: 192.168.1.99 (Preferred)
    ... Subnet mask: 255.255.255.0.
    ... Default gateway. : 192.168.1.1.
    DNS servers...: 192.168.1.1.
    NetBIOS over TCP/IP...: enabled

    Ethernet connection to the Local network card:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    Description...: Realtek RTL8139/810 x Family Fast Ethernet NIC
    Physical address.... : 00-1B-24-20-AB-E7
    DHCP active...: Yes
    Autoconfiguration enabled...: Yes

    Hello

    You said that he can connect with WEP but not WPA.

    There is therefore no connection with the router under WPA.

    For as far as the OS is concern that WPA doesn't have a general problem in Win XP SP3, Vista or Win 7.

    Encryption in many cases problems stem from the problem of drivers.

    Quote: "I'm still stuck with a non-working wireless network on my Vista laptop and the place where it is normally used. This means in technical terms.

    For example, there's something special about this wireless source?

    You can try to check the integrity of Vista using the SFC - http://support.microsoft.com/kb/929833

    If I were in that situation, I'll borrow a wireless USB network who knows work and try to make sure that it is not wireless card related problem.

    BTW, have you checked the process that there is no residual "junk" left by the safety test.

    Download it, run it and take a look at changing it running.

    http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653

    Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET

  • Wireless LAN on Equium A210-1AS connection with WPA-TKIP encryption problem

    I have a 1AS Equium A210 with Vista but cannot connect to the internet via a wireless router cable modem NTL using WPA-TKIP encryption and 5600 philips.

    The laptop shows the base station wireless with a beep sound intense but said that the base of the station is not responding or is hidden when I try to connect to the internet.

    I'm using the correct password.
    I am able to connect to the internet via the base station when connected via the ethernet cable. Other old computers connect wireless with no problems.

    I heard that some combinations of chipsets with Vista can be the cause of some of these issues.

    Clear advice or ideas on what I could try to get wireless internet would be greatly appreciated.

    Have you checked to connect the laptop to the router WLan with WPA encryption settings? Please do. You must disable the WLan encryption to test the WLan connection

    If the laptop could connect properly, then encryption is certainly the reasons why the laptop can not establish the WLan.

    Maybe your wireless network card does not like this on the encryption support or you simply have to update the Windows operating system and the driver WLan.

  • Extension of memory Tecra T9100

    Memory modules can be installed in Tecra T9100 with PT910E-00DYG-GR part number?

    I have 256 MB, I can install a module with 512 MB?

    Hello

    Yes you can. This laptop supports these modules:
    PC2100 128 MB (PA3126U - 1 M 12)
    PC2100 256 MB (PA3127U - 1 M 25)
    PC2100 512 MB (PA3164U - 1 M 51)

    You can also expand max. 1024MB (2x512MB) memory
    concerning

  • Wireless and WPA - PSK on the Satellite L505 - 10 p

    Hello world!

    I recently bought a new laptop, Satellite L505 - 10 p. I installed Windows 7 Pro (64 bit), but the wireless card was not recognized first (it is a Realtek RTL8191SE Wireless LAN 802.11n PCI-E NIC), so I went to realtek drivers page and downloaded the drivers but it didn't work, so I went to the toshiba support page and then I found the package with drivers fully functional under 64-bit windows 7... Well I thought.

    I have two wireless access points I needed to connect: with WPA (TKIP + AES) protection and the other with WPA - PSK. Initially, it didn't work at all with the windows Connection Wizard, the wpa key interpreted... and he was always asking for it. So I installed ConfigFree toshiba web site and I have connected to my WPA (TKIP + AES), but the other doesn't work at all, it always says "connection error" (with ConfigFree)...
    I know that the L505 series is very recent and that she needs an appropriate driver (not only in Windows, but also Linux).

    You encounter this kind of problem?

    Thank you

    It's me again! Forget everything I said... it was just the Mac filtering on my router blocking the connection...

  • Poor performance on Tecra T9100

    Hi my Tecra t9100 runs very slow even if theres no activity, Windows Task Manager watching > taskmgr.exe process is active and takes the largest part of the treatment. Performance > historical usage CPU running at about 95 to 100% which gives very little idle system.

    can someone help please...

    Hello

    On this path, it is not easy to say why the performance is so bad. I have a unit in my office with 512 MB of RAM and it works well. I sometimes use it for graphic editing, and there is no problem at all.

    Each unit's individual configured and preinstalled. I recommend you to check all running processes. I noticed that many antivir tools are responsible for slow laptop performance. Disable all unnecessary processes and on this way, the CPU will be more power for other applications.

    By the way: how much RAM is there?

  • Unable to connect wireless with Photosmart 2510

    I just upgraded my router from G to N.  I have a Linksys WRT10N.  My network is secured with WPA-Personal.  Since I upgraded from G to N and WEP to WPA, I'm unable to get my 2510 Photosmart to connect to the wireless network.  Initially, I was in WPA2 and downgraded my network to WPA with on security a bit of luck.  I entered all encriptación WPA data in the web browser integrated prior to installation.  I tried to install it several times and everything seems to go through OK but the blue light on the cover of never turns on again when the ethernet cable is disconnected.  When I run the network config. page it says "scanning" status of wireless.

    I talked to Linksys and they told me that the network N should work down to a B network printer.  Does anyone have any suggestions?

    Thank you!

    Hi Kim,

    All printers inkjet wireless HP since 2004 supports WPA - PSK and WPA2-PSK.  All new HP inkjet will certainly support WPA - PSK and WPA2-PSK.

    I'm more familiar with the WRT54G, but the WAPG works as well.  Here is how to convert the WRT54G in a simple access point:

    1. Connect LAN port of the WRT54G #1 and open the web without wire-router page (it should be 192.168.0.1 or 192.168.1.1)
    2. Go to the wireless section of basic wireless settings.  Create a new SSID and choose a channel without overlap, which differs from the WRT160N.  In North America, the overlapping channels are 1, 6, and 11.  Press to save the changes.
    3. Go to the wireless security section and the configuration up to WEP.  Press to save the changes.
    4. Return to the configuration page.  Disable the DHCP server and set the router IP address to something other than then the address IP of WRT160N.  For example, if the WRT160N IP address is 192.168.0.1, and then set the WRT54G to 192.168.0.201.  Make sure that the first three groups of numbers of the IP address are the same.  Press to save the changes.
    5. Now, connect an Ethernet cable between WRT54G #1 LAN port and one LAN of the WRT160N ports.

  • Tecra T9100 recovery disks

    Hi guys. I was left a Tecra T9100, model No.: PT910E-5XQ1N-EN laptop and I desperately nreed to ge the recovery disks for it that I can't get one of the drivers, audio, video, wireless etc to work by setting up from scratch.

    Do you know where I can get these discs?

    I would really appreciate your help.

    Can you contact me here or on my email address, please

    [email protected]

    Thanks guys,.

    See you soon

    Hello

    Simply contact a partner of service authorized in your country because they can send a request to toshiba for ordering the recovery media for you.

    You can find the nearest ASP by clicking on the next page-> http://eu.computers.toshiba-europe.com/-> Support and downloads-> support-> repairs maintenance home page &-> find an authorized service provider

    Welcome them

  • Satellite A100 - 003 WLAN (with WPA - PSK) connection timeout

    I have a laptop Satellite A100-003 with preinstalled in Windows Vista.
    When I try to connect to my router with WPA - PSK (TKIP) I have error:
    Wireless authentication failed because of a time-out.
    My laptop and the router configured properly! I installed the new drivers intel 3945ABG chip.
    WPA2-PSK and WEP are working very well.

    Hello

    The same thing happened on my old laptop.
    I was not able to establish the WiFi connection for more than 1 min with WPA encryption.
    I downloaded the latest Atheros driver and updated everything.
    Everything works very well with WEP but not WPA.

    Then I disabled the option to clean Windows configuration and use the Atheros utility. Now everything works fine!
    I recommend using the Intel Proset utility and check all the possible settings!

  • Need help to set up: 2 different wireless with SSID 2 routers on the same network

    Hi all:

    I read on the forum trying to find the answer to this question, but have not found a very clear answer that satisfies all my requirements autour.  An explanatiion more in depth.

    I have 1 IP coming via cable modem.  I want to configure two wireless routers (one secured with WPA-TKIP and a non-secure network - a 'guest' If you want to) each with different SSID.  The secure network would be for my server, PC home, webcams IP, DynDNS, update; While having an unsecured wireless router that friends and family can access.  Ideally, I don't want any person who accesses the router unsecured wireless to access my secure network.

    Is someone can you please tell me if this is possible.  I think that it is based on some posts, I've seen, but specific details about how to do this would be appreciated.  In addition, my DynDNS must always be able to be updated with the IP of my ISP so that I can access my server and webcams home.

    MATERIAL

    2 WRT54G

    1 EZXS55W

    1 WVC200

    1 WVC54GC

    (all my stuff - webcam, dyndns, server, etc. - working on my secure network.) I just need to add the non-secure network)

    I know it's a lot, but I'd appreciate any help.  Thank you.

    You must be connected to the modem router WRT54G main. Set up the network secure on the main router wireless. Connect all of your computers or wireless devices for the main secure wireless network.

    Consider that the IP address of the main router is 192.168.1.1.

    Now connect a single computer to Port 1 on the second router wireless.

    Open the second wireless router configuration page. Settings wireless SSID, unsecured.

    Change the IP address of the second router 192.168.2.1. Save the settings.

    Connect the cable from the Ethernet port on the main router to the Internet second port router wireless.

    The second power cycle wireless router.

    Now the host computers connected to the second network unsecured wireless Wireless will be able to access the Internet only. They will not be able to see the computers or devices connected to the first router.

  • iPhone 6s doesn't sync wirelessly with iTunes

    I have a new iPhone running OS 9.2.1 6s.

    Is set upward wireless at the Apple store, restored from my previous iPhone 5 and me kept updated iOS and phone saved wireless, and had not annexed it with iTunes on my Mac, until today.

    I have the gasket with the USB cable into my iMac running the last El Capitan, iTunes 12.3.2

    The iPhone has shown in the section "My devices" in iTunes, but I immediately got a message "there is a new version of iOS for the iPhone (9.2.1). iTunes started download iOS 9.2.1 but I stopped, because the phone has already 9.2.1.

    I checked the preferences to allow the iPhone to sync wirelessly with iTunes, applied and then ejected from the iPhone.

    My iPhone is connected to wifi, but when I restarted iTunes it does not connect wireless - the wireless only showing in iTunes is my iPad.

    My questions are so

    (1) why only iTunes can only see my iPhone 6 is already running the latest version of the iOS software

    and

    (2) why didn't it connects wireless when I set the preference to do?

    Thought I'd ask advice here before that I contacted Apple support.

    Thank you

    Caroline

    There is a different verson of 9.2.1 released by Apple to fix the error 'January 1, 1970.  It is only available through iTunes, not live.

  • My Tecra A11 - 11K new comes with w7-64 bit, but I need w7 32bits

    My Tecra A11 - 11K new comes with w7-64 bit, but I need w7 32-bit because of an old program that I use for professional use.

    I bougth a w7 32 and 64 b license.

    My question is how to install w7-32 more than 64. I think that it is as easy as plug-and - go CD. Yes?

    But I want to preserve utilities Toshiba, other programs that come with the w7-64 pre-installed. Where can I get them? The Toshiba Download Center?
    And which one I need? All the?

    Thank you for your help.

    > My question is how to install w7-32 more than 64. I think that it is as easy as plug-and - go CD. Yes?

    Do you mean that you have a Toshiba Recovery disk?

    If Yes, then it's like you said; put the recovery disk in the CD/DVD drive to start this disc and during the procedure, you will be asked which version you want to choose.
    Then choose 32-bit that s it ;)

  • Tecra A2 - Display driver compatible with Windows 7?

    Hi all
    I've recently updated my Tecra A2 to Windows 7 (obviously without checking compatibility). It is working very well, but I can't find a driver (if it exists) for my graphics card. I've exhausted all over support of Toshiba and the forums pages, and I feel like the only solution is to buy a new card.

    Can anyone help?

    See you soon

    Hello

    I m asking you to install Windows 7 on older Tecra A2. Are not satisfied with the operating system preinstalled?

    Normally, you can get all the drivers on the Toshiba page. I checked and I can't find a driver for Windows 7 or Vista (most Vista drivers are also work on Windows 7). What can you do now? That's strange but as I know the Tecra A2 is equipped with an Intel card and you should check the Intel website for a pilot. Normally it should good one.
    Check it!

  • Can not put on wireless with FN + F8 on my Satellite L750D - 19 c

    Hello

    I can't put on wireless with FN + F8 on my Satellite L750D - 19 c with windows 7. It stopped work at shot, and I cant get it up and running again. I tried to install the latest drivers and the disabled option 'save energy '.

    / Magnus

    Hello

    I have the same problem with my satellite L670.

    The FN keys do not work and I am not able to use my Internet connection. : () o

    I used to get these buttons to apear on the top of my screen to get the mouse towards the edge.

    So I could turn the wireless on / off power with the mouse.

    But these "maps" doesn't apear. Or my settings on the camera to the left of the screen.

    Thank you very much.

    Post edited by: PearlSabian

Maybe you are looking for