Telnet TC6.0

Similar Questions

• Unable to telnet to C60

  Not sure your gus have that experience before, I was unable to telnet to codec C60 with TC6.0 (new codec). The Telnet service is enable. Access web and ping works fine.  Whenever I put telnet it keep on to message as below.   I have it set back to factory default via the web and still the same issue.  any clue?

  Command: telnet IP codec and the response was as follows:

  The name Info: localhost: success

  Temporary in name resolution: success

  connection to host lost

  DV
  

  Hello Din,

  You probably hit bug CSCue72551 (Telnet to EX90/C90 failed)

  Workaround solution:

  Make sure that DNS is running properly this codec can do a reverse lookup of the address that connects in the codec.

  Or upgrade to a version that contains the fix.

  Or using SSH. (A recommended from my point of view)

  HTH,

  Ahmed

• Open a Telnet with Firefox link and bad things can happen

  I happened to come across a site with a number of links, and I chose the one who happened to be a telnet link. This is my experience, and I had to put myself in the shoes of the average user who knows nothing about programming.

  The link that has caused problems of Firefox where Firefox was chosen to run it is:
  Telnet://DXC.nc7j.com:7300

  Click on the link and Firefox tells you you have to select a program to open the Internet shortcut Shell extension DLL. I've never heard of this, and I have no idea what to do here.

  Choose to open with Firefox.

  Now, if an error handling routine had taken that Firefox, which is not able to Telnet, was chosen by the unconscious person behind the keyboard to move forward and do Telnet, the error handler advises the user on the fact that this Protocol is not taken in charge and kill the process that is going to run out of control if not. Or to open the program which will run the Telnet session.

  Better yet, I clicked on the link Telnet and offer a better description of the choices.

  After all what happened, that I have installed a browser based on Chromium, iron and he opened a Telnet session window immediately.

  This did happen, clicked on Firefox to do this chore and was welcomed by an opening endless empty tabs and the browser is closed, he raised and I was off to the races again. And once again.

  OK, so this isn't getting us anywhere.

  Firefox opens once more, this time hitting the big red X to close it and leave asked it to close but many tabs invites when even sitting there.

  I chose to run CCleaner and I put that to blow the Firefox Cache and session. Run CCleaner and tell him to force Firefox closed when he asks that Firefox is open.

  If by chance, Firefox launches once again, the timing was perfect as the file that was the origin of Firefox open wasn't cleaned yet, then run the CCleaner a few times. When Firefox is the opening is no longer, we are in the world of mental health.

  Now, I could go to reset the Tools Options Applications tab and search for Telnet and replace the use of Firefox with 'ask me '.

  Fortunately, I know a little bit more than some about the computer, and I knew I had to use a utility to clear the Firefox cache.

  You have a description of the problem in your knowledge base, but he has Firefox open the empty tabs without end, but Firefox was closed and the situation is under control... Restart Firefox manually, start a new session, and then enter the menu Tools and difficulty setting.

  There is an article in the knowledge base on this theme, but there the user to close Firefox, and then everything is back to normal. You can open Firefox and enter the menu to resolve the problem. There was a mention in there any malware as a possible cause of the constant reopening that I lived, but Malwarebytes scans were clean.

  "Well, this is awkward!" I have seen that nice touch to Firefox for many years and may I want to congratulate those who thought of that one.

  There are a couple of settings related to resume your previous session after a crash:

  (A) resume automatically, but if Firefox crashes twice in a row, displays a list of windows and tabs and let me choose. (default)
  
  (B) does not resume automatically, always show the list of windows and tabs and let me choose; (I recommend this approach) or
  
  (C) never automatically resume and do not display the list.

  Switching to B or C requires a visit to Firefox about: config preferences editor.

  (1) in a new tab, type or paste Subject: config in the address bar and press ENTER. Click on the button promising to be careful.

  (2) in the search above the list box, type or paste sess and make a pause so that the list is filtered

  For "B":

  Double-click the browser.sessionstore.max_resumed_crashes preference from 1 to 0 (that's a zero).

  For "C":

  Double-click on browser.sessionstore.resume_from_crash preference to change its value from true to false.

• How to enable telnet links in FF8?

  After all the previous links on the add-in UI handlers did not work. I can't find any combination that will open a telnet session when you click on a link telnet://.

  I get the error "Firefox don't know how to open this address...". ».

  Thanks in advance for any help.

  See http://kb.mozillazine.org/Register_protocol

• ReadyNas NV + Inaccessible Frontview. How to fix with Telnet?

  I have a Readynas NV + which allows more access to Frontview. It is more than likely linked to the size of the file log and my OS partition. I recently did a factory reset and forgot to activate the SSH module. Now I'm unable to access the root directory. I was wondering if there are options for this? I tried to do it through Telnet, but without success. I have about 4 TB of data and do not want to save it to the top (it would take days) and I was wondering if anyone has any ideas.

  -Thank you

  Thanks for your help. It's that log files were too important. I had a readynasremote.log file which was very large. Delete this file, frontview was able to load.

  Thanks again,

  Stand

• How the interface telnet or PuTTY or plink software Windows with LabVIEW

  Please find the screenshot attached screen of the problem that face here.

  He is, can't open the telnet session by using the IP address of the DEVICE. But after that am not able to send commands or argument to the PuTTY or plink.

  Exec System does not accept standard input.

  In the plink.exe screenshot began operating only after sending to put manually... and after getting invited ">" if I send the command 'SEND' to plink.exe he answers returns with the data of the unit.

  Here I am not able to automate this send command Enter and SEND to get the data of the unit.

  He will be grateful if someone give me a solution.

  Thank you

  Vijay

  I solved this with Telnet VI by adding \r\n for all orders that we send to the unit.

  Pls find the attached final VI in LabVIEW 8.6

  Concerning

  Vijay

• Connect to a device using TELNET

  Hi all

  I'm again using LabVIEW afairly... I have only the subset of basic skills so far.  So I would respectfully when you reply to a catchall as possible please.  In fact, a sample project with a lot of explanation would be absolutely fantastic.

  Essentially, I have a Kollmorgan AKD motor controller device (more precisely the model AKD - 00306-x) which controls a servo controller.  It uses the TELNET Protocol, among other things, to communicate with him.  So far, I was able to use the TELNET of MS and Kollmorgans workbench service to communicate with the device with great success.  Although the workshop of Kollmorgan is a good program, I am looking for more precise control.

  Here's the question:

  What is the best method of sending the commands mulitple like that of the TELNET Protocol (to where I can enter a command, have the Kollmorgan run, enter another command, run,... multiple iterations this... with out disconnecting)?  In other words, I want to be able to enter a few commands, one at a time, and the Kollmorgan executes each command after each time that the key has been affected (with them having to restart the application... because of the disconnection).  So far, I've implemented a while loop (without success) and one for the loops (with no success).

  With the involvement of a loop, I can send a command and carry out very well... the connection becomes just disturbed/disconnected.  My working model of the program, out of the loop is attached.  You will find that it does what an execution (using the "run once").  If you use the button "Continuous run", the buffer is literally invaded (which probably you know).

  Thanks in advance.

  You have 2 problems:

  1. Do not connect a value to the N of a loop terminal for and auto-index at the same time. One or the other. In your case, you're automatic indexing. Remove the 9 constant.
  
  
  2. Your strings are not correct. If you want to enter special characters such as newline and carriage returns, your string must be in '-' display mode. Otherwise get them interpreted exactly as you enter them. You send your channel, then the character "-" and the character "n". This is not the same thing as the newline character. Right-click on the string element, and then select this mode on the shortcut menu. You will see there are two characters "\" before the "n" and the characters 'r '. Change all the double-backslashes to those unique.

• A Telnet session can be passed 1 VI at the test bench

  Test and Lab View, each of my tests open a telnet session, runs a test, close the session and is then repeated in the next step but run a different test.  So I get a pass/fail for each step.

  Is it possible to open a telnet session in the format box test (using a VI created in lab mode) and move this telnet session to another VI in the main area of testbed.  (VI) test steps across would not open a session, saving time.

  Thanks to all who responded.  To solve my problem, I created a VI that opened a telnet connection.  I did that Vi the Telnet on a control that I traced on a connector.  I placed this VI in my SETTINGS teststand.  In teststand, I made the telnet on a variable FileGlobal (called Telnet_Connection).  Then, in the region of the hand of teststand, I place a VI that performs a test on the telnet with on opening a connection.  I did the Telnet in a control and it mapped to a connector in the VI.  TestStand I made the telnet in the same variable as the telnet on created in the Setup program, Telnet_Connection.  Run the test and it worked.  My biggest problem was not knowing not how to create a variable or pass a variable in Teststand.  Thanks again for your help.

• LabVIEW does not listen to teststand while that connected to telnet

  Hello

  I have a telnet open to some hardware connection and I'm passing in variables my LabVIEW that speaks to this telnet.

  The telnet runs from my command prompt (which I run as an executable at the beginning of my teststand sequence).

  My problem is when the command prompt is started, and the connection is made the variables being passed to teststand to labview are ignored (this is perhaps due to being of labview single thread to the telnet session?). I can't stop the connection to the command prompt at all (if the connection is lost the test fails) I am looking for a solution where I can leave the session running telnet as my labview is always listening to what is spent to teststand.

  I know its what invite telnet session the origin of the problem because as soon as I close my variables can be seen at the entrance.

  Any ideas are appreciated

  Sort my own problem, I think.

  The example provided by labview has a while loop in it. This means that it ends just place locked in this while loop, the first time his name. Sort by removing the while loop (and a little bit of editing) teststand which gives a chance to talk =)

• From the telnet session between calls of LabVIEW, TestStand

  TestStand, I'll call telnet.llb VI.

  In a step TestStand am opening a telnet session to IP address and the collection of the telnet (U32) connection. In the next step of TestStand, I pass the telnet connection to a telnet writing VI, but this error occurs.

  "Dequeue item to acquire Semaphore.vi:1-> Write.vi:1-> Telnet Write.vi.ProxyCaller Telnet"

  The telnet open, write, read and close the excellent work if I get the number of telnet in the same VI session. But I need to keep the session open between TestStand calls because a huge VI is not possible.

  Thank you

  Josh

  Verify that your adapter for LabVIEW has reserved the execution. If it is already, I don't know, you may need to create a parallel thread that keeps the session active.

  CC

• Telnet buffer issues

  Hello

  Modems are configured to him telemeter data to a LabView VI.  The LabView VI works as expected when cable to the instruments.  A modem and an internet connection now replace the electrician, so a reconfiguration of the VI was required using Telnet reads/writes instead of VISA reads/writes.  Initially there was some deformations associated with the configuration of the modem, but those who have been developed.  Pattern of backstory: I think I've isolated my question how do I use/configure Telnet Read.

  My question: drop-outs of data and incomplete data packets.  I get 25 bytes of binary data per second, easiestly considered Hex when it broadcasts in.  A valid packet looks like this:

  0119 81CC 4 47 884B 5722 7ECA 000D FA37 7E52 FC66 7CF7 25 0 04

  where 01 begins the sequence and 04 ends the sequence.  All the mess inbetween is useful for me but totally uninteresting to most sane people.  Attached are two examples of code.  The first, TelnetEx.vi, is a simple version of how use the Telnet Read.  When I use this Setup, I think I'm buffering 25 bytes of data, then end the line each time a hex04 is observed.  Too often, I receive packets that are not 25 bytes long, but end in hex04.  Moreover, I could not help gold '' normal' immediate' mode with the Telnet Read - I get some sent to all data packets.  (??)

  So I thought if I could electrician a way to detect the package of 25 bytes of data in the buffer, then I would outwit the incomplete packets (an incomplete package causes false ears in my data as the VI is wired to look for data in a location particular byte in the data packet). An example of this attempt of poor quality is shown in TelnetEx.vi.  When I apply this filter, I don't get any data.  The filter is supposed to find hex01, then search for hex04, then count to see if they are 25 bytes apart and if they are, send these data to the rest of the VI because it's a package valid.

  One last note: I've been tinkering with the VI and found that if I use the delay time at a sampling faster (10 Hz) that my instrument (instrument = 1 Hz) rate so less I delivered incomplete packets and sometimes there is a break which resembles an abandonment of data and then I get several packages at once.  It's probably a problem of connection/packet delivery, but maybe someone has seen this before and knows a good way to deal with?

  Is the buffer of Telnet Read a FIFO?  Is there a more sophisticated method to check the validitiy of a packet of data that my attempt mutilated?

  Thank you

  ~ Tristan

  It's here.

• How can I stop people to send e-mails via telnet from outside

  Hello

  I am looking for a solution for 1 month, we exchange server 2010 with local antispam (integrated with the firewall)
  anyone can make (public ip Exchange) telnet port 25 and can send emails for mailboxes mailbox internal * address email is removed from the privacy *.
  How can I disable the telnet so that if someone tries to send e-mail from outside the local domain to get error or request password.
  We had a serious problem because of this, someone outside email sent using telnet to our Chief Financial Officer and he thought it was a valid email address :(
  Please help please

  Hello

  I am looking for a solution for 1 month, we exchange server 2010 with local antispam (integrated with the firewall)

  anyone can make (public ip Exchange) telnet port 25 and can send emails for mailboxes mailbox internal * address email is removed from the privacy *.

  How can I disable the telnet so that if someone tries to send e-mail from outside the local domain to get error or request password.

  We had a serious problem because of this, someone outside email sent using telnet to our Chief Financial Officer and he thought it was a valid email address :(

  Please help please

  Try asking in Exchange Server Forums:
  http://social.technet.Microsoft.com/forums/Exchange/en-us/home?category=exchangeserve

• string of Telnet to excel

  IM new to programming so im sure im missing something but...

  Im trying to collect data reception IM of a telnet session. Its in a string format.  Data gets displayed in a tabular presentation, and I would like to take this and in his bed in excel.  I'll also have to configure to several polling stations of the data and add each one to the file.

  so should I create several strings that analyze each data point, and then build a 2d array to put in simple table vi in the report general toolkit?

  or y at - it an easier way?

  What is not easy about it? You already seem to create a 2D array in order to display the data on the table, in order to have the data. With the Excel simple table VI, you can specify the cell where start by writing, so you really don't have to write the entire table, only what you just got at this precise moment in time. I don't know what your Excel file is supposed to look like, but if you're just enregistrer to save on file that you could use instead write it into a spreadsheet file. He recorded in a text file delimited by tabs you can open with Excel.

• WMI Telnet Port number

  I'm not able to port WMI telnet to a particular server. At the same time, I was able to telnet to the port even other machines that I have connected.
  Please help me solve this problem.
  Thanks in advance
  Aldo

  Aldo, could you please verify if WMI port is listening to this server.

  Port number: 135

  Concerning

  Nithin

• Bytes to the port for Telnet sessions

  It is my first foray in communication with a Telnet Server.

  I put my old code to level to navigate the structure of menu on our previous devices that use a serial port now communicate by Ethernet using Telnet.

  Because the read VISA you should know how many bites to read my old code is highly dependent on 'bites at the port' vi.

  Is there a similar way to do this for a Telnet connection?

  Now I have to count the bytes and put it in a test outside, play with the values until I find something that works.

  The problem is that I don't know exactly how many bytes will be returned after entering a command because the unit will "inject" error messages and system of right on the telnet port.

  Telnet is mainly a line oriented protocol. So, basically, it should be enough to activate the mode of termination in VISA and simply start reading data with a fairly large number for the bytes to be read for you ensure that you always get at least one line. VISA will automatically terminate all read when he meets the stop character in the stream.