Temperature for the host hardware status

Similar Questions

• DELL PE R710 missing sensors on the tab 'Hardware status' vCenter ESX after latest patch update!

  Last month, I update all my ESX host with the latest patches for ESX from 28/04/2011 (ESX410-201104001) via the vCenter Update Manager, earlier this month, accidentally, I have some verification to be done in the server room and noticed a hard drive failure on one of my DELL R710 Rack servers, I you connected the VirtualCenter client and when I click on the tab 'Hardware status' (where the alarms about the) Configuration hardware server usually appear), I noticed that my storage sensors are missing, the network sensors as well! ?? I recall that on March I did have another server hard disk failure, but I saw an alarm (for predictive failure) on my vCenter and I call Dell to replace the drive back!

  I also noticed that now the number of my server sensors are between 73 and 88, before I remember although there were a couple hudred of them! ??

  After some research on the net, I did I frimware/BIOS upgrade of all hardware on the servers, as I install OMSA 6.5 and Dell management plug-in to vCenter and all seems to work just fine, but storage sensors and count sensor under the tab 'Hardware status' issue was not resolved. I think there is a problem with vcenter, because when I connect directly to the host through the vsphere client, in the "State of health" tab all the material appears correctly. I found subjects with similar problems, but they have been with HP servers and not answered or solved!

  Is there anyone with similar problem or no answer to my question?

  Thanks to all in advance!

  godjak

  PSIF there need I can post some screenshots!

  Confirmed.  Without patch ESX410-201104401-SG, my other R710 has a full complement of sensors.

• The number of heartbeat for the host data warehouses is 0, which is less than required: 2

  Hello

  I have trouble creating my DRS cluster + storage of DRS, I have 3 hosts esxi 5.1 for the task

  First, I created the cluster, no problem with that, so the DRS storage was created and now I can see in the Summary tab

  "The number of heartbeat for the host data warehouses is 0, which is less than required: 2".

  I search the Web and there are similar problems when people has only a single data store (the one that came with ESXi) and need to add another but in my case... vcenter detects any...

  In the views of storage I see the store of data (VMFS) but for some strange reason the cluster not

  In order to achieve data warehouses minimum (2) can I create an NFS and map it in THE 3 esxi hosts? Vcenter which consider a play config?

  Thank you

  You probably only have local data warehouses, which are not that HA would require for this feature (pulsations datastore) to work properly.

  You will need either 2 iSCSI, FC 2 or 2 NFS volumes... Or a combination of the any of them, for this feature to work. If you don't want to use this feature, you can also turn it off:

  http://www.yellow-bricks.com/2012/04/05/the-number-of-vSphere-HA-heartbeat-datastores-for-this-host-is-1-which-is-less-than-required-2/

• I'm building a Windows98SE virtual machine on a host OS to Windows XP Home using Virtual PC SP1 (with the fix for XP home). Do I need to install drivers for the emulated hardware?

  As I understand it, all hardware is emulated (that is, it 'sees' that which is emulated, not the physical hardware in my computer: sound card, motherboard, etc.), correct?  Here's my question: do I need to install the motherboard drivers, video drivers, or the audio drivers for the emulated stuff.  In other words, even if I have an Athlon XP 3000 + processor on an ASUS motherboard, do I need to install the drivers from the motherboard with the chipset emulated by Virtual PC?

  You have no need track down all the drivers.  They are installed automatically.

• Windows 7 poster waiting for the host window for spot on the restart or shutdown

  Every time I have shut down or restart my computer, I get a screen that says "Waiting for task host window" I tried to clean the registry, I did a chkdsk, I ran sfc/scannow several times now and this issue will not go away.  I am running Windows 7 64-bit with 4 GB of ram. I also tried to apply the patch, but I always get "this update is not applicable to your computer."

  Hello

  Thanks for posting your question on the forum of the Microsoft community.

  I would like to know some information about the problem so that we can help you better.

  1. have you done any hardware or software changes to your computer recently?
  2. What is the brand and model of your computer?

  'The Taskhost' is a generic process, which acts as a host for the processes that run "DLLs" rather than "Exe". Starts, it checks the registry services part to build a list of the DLL-based services it needs to load, then load them.

  I suggest you try using the steps in this Microsoft support article and check if it helps.
  Reference:
  Why my computer won't turn on or off quickly?
  http://Windows.Microsoft.com/en-us/Windows/computer-wont-turn-on-off-quickly#1TC=Windows-7

  In addition, you can view the details on the performance of the computer of the Task Manager.
  Reference:
  See details about your computer's performance using Task Manager
  http://Windows.Microsoft.com/en-us/Windows7/see-details-about-your-computers-performance-using-Task-Manager

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Reading of temperature for the use of Thinkpad T510

  Hi all

  I have a question about the standard temperature / acceptable range for computers thinkpad t510 operation. My setup is currently my t510 is connected to an external monitor, speakers, keyboard and mouse. Therefore basically a desktop computer except using the innerds of the laptop as the "heart" of the system. My power manager put the CPU to adapt. The temperature readings that I get for the processor and the motherboard download the program called of Piriform Speccy are on average 60 to 61 degrees C. I wonder if it is within the normal temperature of operation for the laptop and if it is acceptable. What is the temperature not okay and why it is so high, it's that I use external references. Also, I even use heavy workload for the laptop and more for the web, browsing and listening to music and work on documents / spread sheet so basically, office work.

  And finally, the problem of temperature would resolve if I would in the future to get a computer laptop w530 since these laptops are more "powerful"? Or is that evil and the temperature is normal.

  Thanks in advance for answers

  unit88888888 wrote:

  The temperature readings that I get for the processor and the motherboard download the program called of Piriform Speccy are on average 60 to 61 degrees C. I wonder if it is within the normal temperature of operation for the laptop and if it is acceptable.

  Yes ~ 60 ° C is quite normal. I would get concerned if temperature readings consistently exceeded 80 c or if the fan was constantly. Otherwise you will see the temperature fluctuates as activity processor and graphics vary.

• Compensation of temperature for the strain gauges

  I'm trying to compensate for the effects of temperature on an extensometer placed on a sample of carbon fiber.  The sample will be only responsible uniaxialement.  The temperature is a major concern here, for an electrical current will be executed by him for purposes of measurement, which should also heat the sample.  I read in the document 'Strain gauges measure' on the website of NOR (http://www.ni.com/white-paper/3642/en), but he speaks with a Measurer of mannequin, he speaks not just how this second pledge, placed perpendicularly to the axis of the applied force, we are not talking of how connect to the strain gauge module , in my case the NI 9235, to use for temperature compensation.  My first thought was just connect each pledge to the module as their own separate channels, using quarter-bridge in the LabVIEW software set up, calibrate the two gauges while not external physical load or temperature effects are applied, and then, after the test, by subtracting the measure pledge Sham in the values of assets pledged.  But then I started wondering, is there a better way to do this?  Can I use the half-bridge configuration, or some other configuration with the 9235 to automatically merge the readings two pledge during the test?

  I'd appreciate it really any advice that anyone can give me on this.  I don't want to build my own external wheatstone bridge (other than the built-in NI 9235), and I would like to make these measurements as accurate as possible.  I have also considered the possibility of the compensators measurers, but I don't think this would be applicable in this case, the complexity of the matter - being a composite.

  Hello WyoEng,

  You want to use the temperature compensation is referred to as a quarter bridge II configuration (image below). This configuration is very similar to a half of the bridge, while the second element (R3) is inactive because it is placed transversely to the direction of the load, without strain and in the same location the active gage (R4) to take account of thermal affect.

  

  NI 9235 supports only a quarter bridge I configuration for measures of constraints.  You will get an error if you try to use this module for any other configuration of pledge of strain that is not quarter bridge I. Thus, active policy that you asked to use two channels to read the pledge and the dummy gage will be the best option to use NI 9235 to compensate for thermal effects on your extensometer.

  Another option would be to look on the NI 9237 which supports a quarter bridge II configuration.

  Best regards

  Izzy O.

  Technical sales engineer

  National Instruments

  NI.com/support

• A timeout occurred while waiting for the host controller EHCI interrupt on answer Async ahead Bell.

  Whenever I put my adapter wireless netgear n150 under heavy load (download of World of Warcraft for example), it will go down to connection and until I restart the computer the adapter usb port is useless.  I dug into the event viewer and found that a timeout occurred while waiting for the EHCI host controller interrupt on the asynchronous response advance doorbell, source usbehci.  This seems to have been a problem with windows 8 I found other threads referencing but I can say that they are pre-release and some actually work solutions have been validated.  I already assured that all drivers, firmware and chipsets are up-to-date and compatible.  ANYONE please help?

  Quick fix I found:

  -try falling back to WiFi G rather than use N
  In my case, it works... is no longer a fall. But not the same bandwidth...

• Question for the host resource

  Hello

  We have 1 blade that hosts a physical SQL Server on it. The resources of this blade are 10 total to 20 cores processors and 512 GB of RAM on it. We want to virtualize it soon, but we don't have any other guests that we could use this size. We have a few available hosts that are 8 to 16 cores CPU and 256 GB of RAM. I was hoping that I could create a cluster with 2 of these hosts and virtualize the largest physical machine in the cluster. I know that when I virtualize this machine, he will live on one of the hosts at any given time. My question is if these hosts would be 'pool' their resources so that this machine could use more than a single host would offer it. Is it possible at all or not? If not is there another work around for this problem I have?

  We are on vSphere 5.5

  Thank you

  My question is if these hosts would be 'pool' their resources so that this machine could use more than a single host would offer it. Is it possible at all or not? If not is there another work around for this problem I have?

  No, the maximum resource that can use a particular virtual machine will be limited by the maximum available on a single host computer running this VM particular resource. Workaround is to add more physical resources on the host or create the virtual computer with limited resources. Are you sure that your virtual machine uses really 20 the processor cores and 512 GB of RAM? Most of the workload running on the physical server uses all resources.

• How have the guest OS disk cleaning disc space come on for the host operating system hard drive?

  People,

  Hello. I use VM Player 3. The OS is Windows 7. Guset OS is Windows Server 2003.

  Because the host OS Windows 7 C drive is nearly full, I need disk cleanup for drive space in Guset OS Windows Server 2003.

  Guest OS Windows Server 2003 VM hard drive parameters:

  Size current 92.5 GB,

  Maximum size of 150 GB.

  I use Disk Cleanup tool to clean C:\Document and Settings\Temp\ and temporary Internet Files\ administrator to get 32 GB of disk space. Now my computer in Windows Server 2003:

  Used space: 59.2 GB

  86.2 GB of free space

  145GB total space

  But when I check again Windows Server 2003 VM hard drive settings, its current size is 92.5 GB and is not afraid to 59.2 GB after cleaning. Host operating system Windows 7 disc does not come more disk space after cleaning.

  My Player VM VM-> settings is not a function of "Shrink" and the program does not "vmware - vdiskmanager.exe" file to run the function of 'shrink '.

  My question is:

  How to get the approximately 32 GB (92, 5-59, 2 GB) of disk space happen on Windows Server 2003 VM settings and drive hard host operating system Windows 7?

  Thank you.

  People,

  Hello. VMware Tools has tab Shrink to reduce the virtual disk. But the free disk space hard host should be larger that the size of the virtual disk you are reduced to shrink.

  The problem is solved by myself. Thank you.

• Generate custom for the host storage reports

  Hello

  I have a use case where a I need to generate storage reports customized for i.e host host-> screen-> storage reports (reports on :) is an extension on reports taken hosts storage supported? I've seen examples of views views of performance or monitor. Please see the attachment for details

  If the case is taken over the extension on storage reports, we add another report for the reports on as an action?

  Thank you!

  Sorry, the points supported only buckets are those described in the SDK Programming Guide (and in document ExtensionPoints.html)

• Remove emctl blackout/target for the host that no longer exists

  Hello
  I have a power outage set via emctl command line for a host. The host was then taken out of service until it could be removed from EM. Now, I can not remove the failure or target EM as the power failure has been fixed through emctl. I can't access emctl to end because the server was decommisioned. What should I do to remove the target?

  Host: Linux

  Agent: 10.2.0.5

  WHO: 10.2.0.5

  As you have decommissioned the host already guess that historical control data to the host and its monitored databases are no longer required.

  In this case, you can cleanup the agent to the repository which will also clean up the host and control objectives information completely and permanently.

  10G we can do this by connecting to the repository as SYSMAN,

  SQL > exec mgmt_admin.cleanup_agent ('. : 3872');<== this="" deletes="" the="" agent="" and="" all="" the="" targets="" for="" this="" agent="" from="">

• Possible for the host to read the files on virtual machines?

  Is it possible for a host read files on virtual machines?

  If you can get information using vmrun command, then I think that vmware-cmd command will help to define the variables that can think inside the vmx file. As vmx file is inside ESX server only so that you can shut down the VM and edit the vmx file, then you can register to the virtual machine using the vmware-cmd command.

  Thank you

• Considerations for the host of the upgrade of Vista HomePremium for Win 7

  I have a large 64-bit Vista HomePremium PC as the host operating system. I've got VMWare Workstation 6.5.x running as an application on Vista and it supports two computer called Windows XP (essentially nothing else that VMware is running on the host).

  I think the upgrade to Vista from readings elsewhere. Assuming that succeeded, it would be an appropriate next steps approach?

  • Re-install the VMware Workstation application on new host (Win 7)

  • point this VM Workstation application newly installed on the definitions of existing virtual machine (GER) for Windows XP 2 clients

  I'm sorry not to use better terminology in my question. I hope my question makes sense for a VMware guru. I have a bit of memory on the use of the MS Virtual PC 2007 product and I think I understand the concepts but my terms are probably passing offshore for VMWare.

  Other ways to address this issue are:

  • is there a list of audit planning things to do before you change your host operating system while you are a user of VMWare Workstation?

  • is there a special version or service pack for VMWare WS run on a host Windows 7 (64-bit) machine?

  jjamjatra wrote:

  Thank you for your comprehensive reply and suggestions. As I answered Naki, know nothing about the intentions of VMWare on the 'official' support for Windows 7?

  Official support for Windows7 as a host and guest will be included in VMware Workstation 7, which is currently in version beta (in fact it is now at the stage of the Release Candidate).

  VMware comment on dates for the next version, but my guess is that 'soon' is based on the fact that it is more listed on the page of Beta here: http://communities.vmware.com/community/beta

• Access policy for the user whose status is "disabled until the start date.

  Hello
  
  By default political access does not work for the user whose start date is later in OIM 11 g. I have an access policy that the provisions of all users of Xellerate OID. This policy is not work for users who start date is later, i.e. status = disabled until the start date.
  
  No workaround to make the strategy work is much appreciated.
  
  
  
  Thank you
  GYAN

  up to 10g it work very well if you put provisining date as the current date. But, you cannot apply even in oim 11g

  Try below

  Add new udf to the user profile
  reconcile the start date in the new udf and leave the start of oim null date
  In this case the access policy will be triggers and you will be able to get an account created to the OID, and then set the start workflow OID IOM

  for reminder and all just to add trigger for the new udf and update on the changes.

  Note: In your case as OID in disable State it will cause no problem after the user status "disable up to that Start Date. If the resource object in activate State and change you the status to disable up to that starting date, it does not fire disable the user trigger.

  Kind regards
  Mireille nayan