Thanks to the SATA with an RDM controller

Hello

I have a local RDM that I try to use via a SATA controller but it doesn't seem to be a way to do it. I use VMware Workstation, create a virtual machine (hardware 10), add a new hard drive, select SATA and then gives me 2 options: create a new drive HARD virtual or select a created. I choose the second option, point to the ROW and get an error I should have selected "use a physical HARD disk. However I can't find this option anywhere.

Is it possible (via the UI graphics or manual) to add a SATA controller and it points to a local RDMS? Really, I'm testing the solution mentioned here:

Limit of 2 TB of local storage of rdm ESXi 5.5?

Answer to myself, the solution is to use the full-fledged vSphere Web Client. Other tools (including the workstation or the native client) cannot display all information (particularly in regards to the SATA controllers) or even that it is inadmissible claim.

Tags: VMware

Similar Questions

  • I bought a Xbox 360 for Windows gamepad, as well as a Play and Charge kit. If I want the charge with this kit controller, can I use a USB/power Apple to the charge controller plug?

    I bought a Xbox 360 for Windows gamepad, as well as a Play and Charge kit. If I want the charge with this kit controller, can I use a USB/power Apple to the charge controller plug?

    Hi Arvin,

    The question you posted would be better suited in the Xbox Forums. I would recommend posting your query in the Xbox Forums.

     

    Welcome to the Xbox support

    http://support.Xbox.com/en-us/

    Hope this information helps.

  • HP ProLiant DL160 - cannot create the data with local storage (controller, no RAID) store

    Hi all. I appreciate your time and comments.

    Using VMware ESXi (initially), installation (VMware ESXi 5.5.0, 1331820) will very well (install on USB). Able to enter in the console of the vSphere Client, everything seems normal. Any attempt to use local storage, however, is filled with this error message: http://i.imgur.com/40ySsOS.png

    "It was not correct to specified parameters. Vim.Host.DiskPartitionInfo.spec"-" 'HostStorageSystem.ComputerDiskPartitionInfo' call for object 'storage system' on ESXi "< ip address >" failed. "

    I tried both the base (from VMware) installation disc and the "Custom" (HP) HP installation disk. Both have the same problem: all facilities, but local disks - as seen while - are not able to serve local storage. It worked very well (previous incarnation was as Server 2003 file server, no reported\noticed questions). It's not under warranty, its going to be used as a laboratory server. All this seems to work well.

    Specifics:

    HP DL160 G6

    Storage card: ICH10 6 Port SATA AHCI Controller

    Discs: 3 G MDL 500 GB 7200

    Controller and the disks are perceived by the system: http://i.imgur.com/3PAKQHL.png

    Can someone point me in the right direction on what to go here? Research on the error messages do not lead to a lot of help. I'll get more pending. I would be grateful.

    This could be a problem with the current data on the disk. I suggest clean you the partition info using the DD explained to the KB VMware: Troubleshooting in the add storage Wizard error: cannot read this disk partition information to see if that solves the problem.

    André

  • can not play the game with Tron wired controller

    I can play with the controller end with my xbox 360 and there recognize fine as well. However, when I play a pc game it starts fine and I can play normally, but the controller does not work. which means that the game does not recognize it

    Hello

    Please follow the steps below and update us with the results.

    Method 1: You can try to uninstall and reinstall the drivers for the controller and check if it helps.

    a. click the Start button.

    (b) in the search box type devmgmt.msc and then press ENTER.

    c. Select the Xbox controller device and right click on it.

    d. now, select Properties.

    e. in the Properties window, on the driver tab, click Uninstall.

    f. After uninstalling the drivers, restart the computer. This should install it automatically the appropriate drivers for it.

    You can download and install the latest driver by using the following link:

    http://www.Microsoft.com/hardware/en-us/d/Xbox-360-controller-for-Windows

    For more information, see the link:

    http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

    Method 2: Xbox 360 Wireless Controller disconnects or unable to connect

    http://support.Xbox.com/en-us/Xbox-360/accessories/wireless-controller-disconnects-frequently-or-cannot-connect

    For more information, see the links:

    How to connect your Xbox 360 Controller for Windows on your computer
    http://support.Microsoft.com/kb/906347

    How to connect a wireless Xbox 360 controller to your Xbox 360 or Windows PC console
    http://support.Microsoft.com/kb/906947

    If the problem persists, please contact Xbox support for help on this issue.

    http://www.Xbox.com/en-us/forums?XR=shellnav

    Let us know if it helps!

  • The PS4000E with possible defective controller?

    I have a PS4000E that I recently updated the firmware to 8.1.3. During the upgrade and reboot later, the Member would not are online and join the group. However, when we it reboot again, she will appear.

    Currently, he is running on the controller 0, and all is well. A test, I did a reboot, switch to controller 1 and even once, it will not join the group. I ping IP of member management, I can even SSH in to restart it again, back to the controller 0. But he could not reach the controller group 1.

    I really want to solve this problem. It is a very reliable system, but I'm now able to have expected downtime for the next update of the firmware because the failover does not work as it should. My warranty has expired on this table, so I can not just send a ticket either.

    Suggestions?

    Hello

    First thing, is to ensure that both controllers are wired to the top.  In the GUI, when you select the Member, under the "Controllers" tab you see two controllers?   They show the same firmware running?

    You may need to get the serial cable and connect directly to the CM to see what really is failure.  It could be a defective compaq flash card

    Kind regards

    Don

  • T7610 SAS (LSI 2308) precision controller - set the SATA drives?

    Hello

    The controller is SAS RAID LSI 2308 integrated in the T7610 of precision allows to attach SATA hard drives in a non-raid configuration?  I just realized this system has only TWO internal SATA connectors, but I need THREE internal SATA drives.

    What I was asking is if the SAS ports will allow the connection of SATA drives that are not used in RAID mode?  This way I can add my 3rd SATA HDD to a SAS ports.

    Thank you
    M

    We are experiencing the same problem/issue with the T7610 of accuracy by using the controller LSI-2308.  The end result that we would like is to have 2 drives separated - do not use the raid controller.  However, the CD Rom takes up one of the sata drive connections.

    Anyone been able to disable the raid and then controller, seeing the disks during the installation of windows needs to see?

    Currently, I have 2 blank drives (3 TB (ea.) and windows setup does not see the discs - but the raid controller load very well through the configuration.

    What should I do to get readers in windows?  There the meta that needs to be removed?

  • Compaq 610: [Compaq 610, P/N: NX550EA #ACB] latest driver for the SATA AHCI for Win 7 PRO SP1 RUS x 64 controller.

    Hello world!

    Could someone, please, tell me, why there is no driver SATA AHCI controller for Compaq 610 for Win 7 PRO SP1 RUS x 64 in the download section of HP support for Compaq 610?

    (01) where can I get the latest version of the SATA AHCI controller driver for Compaq 610 for Win 7 PRO SP1 RUS x 64?

    (02) the original Intel (r) Matrix Storage Manager V8.9.0. 1023 will replace the ' Standart controller SATA AHCI 1.0 (Microsoft) "(v. 21.06.2006 6.1.7601.18231) with the more recent/latest version?

    (03) will be the upgrade of the SATA AHCI driver improve the speed of read/write of my any percentage HARD drives or this idea is nonsense and absolutely useless?

    I'll be very grateful for any useful info! Respectfully, Tianuchka))

    Hello:

    I would use it to HP... the description tells you what it does.

    The HP 6910P has the same controller and chipset as the 610 HP.

    http://h20566.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=3357379 & swItemId = ob_85204_3 & swEnvOid = 4059 #tab1

    Who answers your questions first 2.

    Regarding the 3rd, I don't know whether or not you notice an improvement.

    If you want to update the driver, you can also install the last utility Intel chipset installation from the link below.

    Download, unzip and run the setup.exe file.  Then restart the PC.

    https://Downloadcenter.Intel.com/download/20018/INF-Update-utility-primarily-for-Intel-6-5-4-3-900-series-chipsets-zip-format

  • Satellite U400-183 lower upgrade to XP - driver for the SATA controller

    Hello

    There is a blue screen during the installation of xp because the missing drivers (SATA controller).
    Could not find the driver, nor on the toshiba Web site on intels.

    Someone who can help? Thank you very much.

    Stefan

    Hello

    Satellite U400-183 seems to belong to the series of PCU44E. Right?
    The European driver Toshiba page provides the drivers for this model.
    You can find on the page of the driver for Win XP Intel Storage Manager and this package contains the SATA drivers.

    But look, man here in the forum, you can find many comments about the installation of the SATA driver why you n t use the search option?

    The best way to install the SATA drivers is the use of nLite.
    He tool free s (you can find it on the internet) and it helps you integrate SATA drivers into the Win XP disc!

    I did it and it worked for me

  • Aurora R4: newly installed SSD running in G2 / SATA300 - how can I 'persuade' the SATA controller to run at G3 /SATA600?

    Good evening.  I was a little indecisive on the place where this post, but I think it's the right place.

    I just replaced the main drive in my Alienware Aurora R4 with a SanDisk Extreme Pro SSD... works perfectly (and quickly).  I realized a clean Windows 10 Pro (x 64), generation to level to the latest version.  I'm not using RAID.

    The SDS is properly installed and connected in the location SATA01.

    This Aurora R4 has the "Dell", well actually "Intel" Patsburg 6 Port SATA AHCI Controller (revised A7), capable of handling G3 / SATA600.  However, two DVD players work to G1 / SATA150 and all four disks are running at G2 / SATA300.

    I have the latest driver for the Intel Rapid Storage Technology technology, confirming a transfer rate SATA 3 Gb/s for my SSD (and the other three HARD drives).

    How can I convince the computer I want to optimize my SanDisk Extreme Pro SSD performance, with the rate of transfer running at G3 / SATA600?

    I searched on through the value of the library of web pages, but not found a solution.  I was hoping that it would be a BIOS problem (installed last), is a question of the SATA controller firmware, but that doesn't seem to be the case.  Technology Intel Rapid Storage Technology driver allows no fiddling, so I drew a blank there.

    Knowledge advice would be warmly received, especially if you have a R4 Aurora that runs a G3 SSD / SATA600!

    Hi Domo_P1000,

    You can search the forums to Alienware for help with this. I found this relevant thread.

  • How to erase the hard drive, foreign State in T630 with H730 PERC controller

    I recently bought a Poweredge T630 Server computer configured with a PERC H730 controller and two 1 TB SATA (raid 1) drives.

    The controller H730 being compatible with no dell certified readers, I bought 2 WD red label records to add more storage space.  The problem I have is it H730 one of the 2 WD drives senses as a 'foreign' drive  Under "available tasks", I see only two options, "Blink" and "Unblink.  Unlike other HDD WD, the controller does not allow me even an option to convert the capable RAID drive.  This only happens to one of the two WD drives. The WD with 'Foreign State' drive is not defective or damaged.  How can I clear the foreign flag on one of the two WD drives so that I can convert the two disks in RAID ready status.

    Hello

    You have a foreigners view tab when you are in the bios H730? If you do, you should be able to use ctrl + N to access this screen, select the controller, press F2 and go to foreign config and have the ability to clear the foreign configuration.

  • Pages of the OPS (with custom controller) does not not in the R 12.2.4 upgrade custom

    Hi all

    There is a problem, I'm dealing with my custom page. I am trying to expand the controller with my custom class, but get the error below

    oracle.apps.fnd.framework.OAException: could not create Java class: (oracle.apps.xxar.cusstd.createcus.webui.xxArCreCusCO) associated with the area: (ArUtilRN). It is probably because the class name is incorrect or not included in the project.

    at oracle.apps.fnd.framework.webui.OAPageErrorHandler.prepareException(OAPageErrorHandler.java:1247)

    at oracle.apps.fnd.framework.webui.OAPageErrorHandler.processErrors(OAPageErrorHandler.java:1435)

    at oracle.apps.fnd.framework.webui.OAPageBean.processRequest(OAPageBean.java:2848)

    at oracle.apps.fnd.framework.webui.OAPageBean.preparePage(OAPageBean.java:1991)

    at oracle.apps.fnd.framework.webui.OAPageBean.preparePage(OAPageBean.java:567)

    at oracle.apps.fnd.framework.webui.OAPageBean.preparePage(OAPageBean.java:455)

    If the file is present in the right folder

    [webui applmgr@gfs3devapp1] $ pwd

    / opt/oracle/gfs2d/FS1/EBSapps/COMN/java/classes/Oracle/Apps/xxar/cusstd/createcus/WebUI

    [webui applmgr@gfs3devapp1] $ ls - ltr

    Total 4

    -rw - r-. 1 applmgr oinstall 1177 Feb 25 10:17 xxArCreCusCO.class

    I have to follow this discussion, but is not help me: https://community.oracle.com/thread/3647610

    Please help.

    Thanks, Jerome

    Hello samia,.

    In R12.2.4, you will need to create the jar with custom classes. Please visit the Doc ID 1577661.1

    Hope this helps you solve your problem.

  • Default mode IDE of DCIS vice, is the SATA controller?

    HP Pavilion m7 - 1015dx, Windows 8 Pro, Insyde H20 BIOS F13.

    I would spend my HARD drive to a Samsung 840 Pro series 512 GB SSD. This will be a clean install with Windows 8 Pro DVD and it has been recommended to switch the SATA of IDE controller to AHCI in the BIOS so that the PLATE to serve properly. Problem is when I enter the BIOS "Insyde H20 F13" it seems very limited, and I can't locate Sata to determine if I'm in IDE or ACHI. When I check the TRIM State via the command prompt, I get "disabledeletenotify = 0" which tells me that it is enabled. So does this mean that ACHI is enabled and I have more to worry about this topic?

    It is also recommended to:

    Enable write cache

    Disable disk defragmentation

    Disable disk indexing

    Turn off System Restore

    Disable the Page file "I have 16 GB of RAM"

    Disable Hibernation

    Disable the Prefetch and Superfetch

    Disable ClearPageFileAtShutdown and LargeSystemCache

    You agree with the foregoing during the passage of the HDD to the SDS?

    Hello

    Even if the option is not available in your Bios Menu, the default setting is AHCI.

    You perform a clean installation on the SSD, I suggest to let Windows configure options of the player without any tweaking extra - for example, it should detect the installation is on a SSD and disable disk defragmentation etc.  The only possible exception is that you can disable hibernation.  You will always get opposing points of view on topics such as the pagefile on SSD (and a mechanical drive)-personally I'd always leave it enabled that the OS was designed to use this feature, and I've never really seen any benefit by disabling.

    Kind regards

    DP - K

  • I want to thank my wifi in another part of the House with an Airport Extreme. But I want to not be connected to the modem main via ethernet cable is it possible?

    I want to thank my wifi in another part of the House with an Airport Extreme. But I want to not be connected to the modem main via ethernet cable is it possible?

    I put in place already to extend the wifi of my modem still connected to the modem via ethernet cable.

    Now I want to be considered on the floor and use it to extend the wifi without ethernet cable

    The AirPort Extreme can extend only wireless signal from another router from Apple, so if you want to take the AirPort Extreme on the floor and extend wireless signal, you will need another airport connected to your modem by Ethernet cable router to produce the wireless signal that will extend the extreme on the floor.

    Another way of saying the same thing would be to say that if you want to extend wireless using a router from Apple, you'll need two of them do... because AirPort Extreme is not compatible with a third-party modem or modem/router for this purpose.

  • Anyone know how I can disable the block with the wikipedia etc. that appears in the place of the cursor if you hover over the texts? This is a most annoying invention! Help, please! Thank you!

    Anyone know how I can disable the block with the wikipedia, google, etc., which opens at the location of the cursor if you hover over the texts? This is a feature of most annoying that one should be able to disable if not needed. I use windows xp family and have the latest desktop version of FF, but I don't think that they are the problem. Thank you very much.

    This isn't a core feature of Firefox (AFAIK) - looks like an extension you have installed is that fact.

    Please send the contents of the extensions section of about: support

  • Satellite L645D-S4025 - need drivers for the SATA RAID controller

    Basically, I need the drivers to load my operating system, because at the time where he leans on my hard drive as unknown. I get BootMGR is missing error, so when I put my Windows 7 disc and go fix it is unclear what operating system is installed.

    So any help will be much appreciated. If you need more just information

    Hey,.

    Have you ever seen the Toshiba page? On this page you can download all the drivers and tools for your laptop:
    http://www.CSD.Toshiba.com/

    For this model with AMD chipset you can find the SATA driver in the display driver package, you must download the display driver. It also contains the SATA driver and chipset.

    But I m wondering why you started this question because there are already several discussions here in the forum about it ;)

Maybe you are looking for

  • Apple Watch connection problems

    Hi all I have a Apple Watch Sport and a 6s watch OS running iPhone 2 and iOS 9 respectively. Sometimes, but not always, my watch will repeatedly connect and disconnect to my phone. I can watch on my phone bluetooth icon go on, then off, then blink (r

  • VISTA FREEZE AT STARTUP - PLEASE WAIT

    Hi need urgent help! PLEASE Last night Windows Vista Home d/load updates new update - IE 8 and I uninstalled Avast anti virus and put on PC Tools antivirus. He asked me to reboot I did and now when you start it freezes on the screen "Please wait" the

  • Why msmpeng.exe consumes all the cpu

    Why msmpeng.exe cause my computer lock in place... and consume so much CPU usage... and how can I fix the problem?...

  • How many times can I load into windows until the c ode becomes obsolete?

    How many times can I activate windows 7 same code key foer in a private home computer?

  • Save the Illustrator brochure in pdf format

    Hello, I am preparing a brochure in illustrator and using a model with 2 work plans (3 sections on each).  When I save it in pdf for printing, I select brands of pads.  But guidelines for the folds do not appear in the pdf file, how do I know where t