The CBAC & VPN Client

I use soft Cisco VPN client behind a Cisco CCCB router running. What are the ports must be opened to allow the client VPN working properly?

I am currently using:

allow an esp

allow udp any any eq isakmp

These are necessary, but you may also need to open UDP 10000 to support NAT - T if IPSec must cross a NAT border along its way.

You'll also need allow beach access VPN client address to the IP address ranges whatever they are to be used in common. This is because packages through the ACL twice, once encrypted using ESP and ISAKMP, there not yet encrypted.

So, if the VPN client has a range of pool to say 10.1.1.0/24 and his contact only the acl 10.2.0.0/16 subnet would look like:

IP access-group extended VPNACCESS

allow an esp

allow udp any any eq isakmp

permit IP 10.1.1.0 0.0.0.255 10.2.0.0 0.0.255.255

Andy

Tags: Cisco Security

Similar Questions

  • Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

    Hello

    I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

    I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

    Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

    Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config

    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config

    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
    Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

    The router configuration

    IKE policy

    VPN strategy

    Client configuration

    Hôte : < router="" ip=""> >

    Authentication group name: remote.com

    Password authentication of the Group: mysecretpassword

    Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

    Username: myusername

    Password: mypassword

    Please contact Cisco.

    Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

    You can use the PPTP on the RV180 server to connect a PPTP Client.

    In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

  • THE SSL VPN CLIENT ERROR!

    VPN concentrator running 4.7. I have to connect to the web vpn session. The SSL VPN Client installs. Message that says: "so that the SSL VPN connection is pending" and later another message appears that says "HTTP RESPONSE received from gateway SSL VPN is not valid" appears.

    What is strange is that the VPN concentrator lists me as it is connected with an IP address assigned to the ACS, but I can't access anything whatsoever. BTW, no ACLs WEB or IP filters are configured for this group that would not allow me access to the network. In addition, with the same information identification and the same group, I have no problem to access the network when the client SSL VPN is not configured to be used. IE web vpn before 4.7.

    Any ideas?

    The "VPN SSL HTTP RESPONSE received from gateway is incorrect" message may appear if the configuration of the client of the concentrator contains over split tunneling 26 entries.

  • How to create a VPN file .pcf for the CISCO VPN CLIENT software profile

    Dear all

    How to create a VPN file .pcf for the CISCO VPN CLIENT software profile

    Concerning

    Hi Imran,

    Can't do much about that because it depends on what authenticate you the VPN server and how the settings. But let me introduce you to the memory layout. Once you install and open a VPN client. Press it again and it opens up a new page for the VPN config.

    Example of configuration as it is attached. But it differs depending on the configuration of your vpn server.

    Once you create and save this profile. Your FCP file is stored.

    Please assess whether the information provided is useful.

    By

    Knockaert

  • Unable to connect via the Cisco VPN Client

    Hello

    I have configured remote access VPN to ASA and tries to connect via the Cisco VPN Client 5.0

    I am not able to connect and watch the journal on the SAA

    ASA-3-713902: Group = xxxxx, IP = x.x.x.x, withdrawal homologous peer table is placed, no match!

    ASA-4-713903: Group = xxxxx, IP x.x.x.x, error: impossible to rmeove PeerTblEntry

    ASA does not support the K9 i.e. VPN - DES is enabled and VPN-3DES-AES is disabled.

    What could be the reason.

    Concerning

    Hi, I had this same problem, here is the solution:

    When you perform a debug crypto isakmp 255, so you see that the cisco vpn client does not support SHA +, you must use MD5 + AN or sha with 3DES/AES.

    Be careful, this debugging is very talkative, but that's the only way I found to get ITS proposal on debugging.

    Well, change your strategy using MD5 isakmp / OF would do the trick.

  • Unable to connect using the Cisco VPN client

    Hi all. I recently configured a 5510 ASA to allow remote access using the Cisco VPN client. The problem is that everything works fine when I connect using a modem classic or on a computer with a public address that I use for testing purposes, but whenever I try to connect with on an ADSL line, I can't access to the resources. I have connection and after that nothing, I can not achieve anything.

    I enclose the relevant configuration information in the attachment. Any help is welcome.

    Depending on the version, add...

    ISAKMP nat-traversal

    or

    ISAKMP nat-traversal crypto

    Should be all you need.

  • What are the ports used by the Cisco VPN Client?

    Hello

    I need to open my outgoing traffic on my firewall to allow two interns (LAN) Cisco VPN Client to connect to their Internet virtual private network.

    I already opened the port 500/UDP, but they are not able to connect. If I open all outgoing ports, they can connect.

    What are the ports used by the Cisco VPN Client?

    Thank you

    You need to open:

    UDP 500

    ESP protocol

    You must also open the UDP 4500 port (if using NAT - T).

    In addition, if the clients are connecting to a VPN 3000 Concentrator series and it is configured for all other options of NAT-transparency, corresponding ports must be open. By default:

    1. If using IPSec over TCP 10000, then open TCP 10000.

    2. If using IPSec over UDP 10000, open UDP 1000.

  • Impossible to install the Cisco VPN Client on Windows 7

    Hello

    After an uninstall successful VPN Cisco version 4. I try to install the Cisco VPN Client 5.0.07.0290 version.

    But after the launch of vpnclient_setup.msi, the wizard starts. When I click on the next button, I get the following message: "installation ended prematurely because of an error".

    As an attachment, I add the details of the discovery of the error in the logs of windows (logError.txt) and the logs generated by the MSI installer in verbose (log2.txt) mode.

    My computer is a lenovo W500 with Windows 7 64-bit and 4 GB of memory (compatible with the requirements of the Cisco VPN Client).

    I have administrative privileges on this computer.

    Please help me!

    I need to use it to connect to my corporate network.

    Thanks in advance.

    BR

    Jerome

    If you want to try another software, I know that works I used it up until cisco came out with a 64-bit client there. Is the 64-bit version of shrew 2.1.0 it worked very well, you will just need your file FCP of cisco for import into if you have. This will tell you if the client or your system at least.

  • How to allow access to a local area network behind the cisco vpn client

    Hi, my question is about how to allow access to a local area network behind the cisco vpn client

    With the help of:

    • Cisco 5500 Series Adaptive Security Appliance (ASA) that is running version 8.2 software
    • Cisco VPN Client version 5.0 software

    Cisco VPN client allows to inject a local routes in the routing table Cisco ASA?

    Thank you.

    Hi Vladimir,.

    Unfortunately this is not a supported feature if you connect through the VPN Client. With VPN Client, that the VPN Client can access the VPN Client LAN host/local machine, not host from the local network to business as customer VPN is not designed for access from the local company network, but to the local corporate network.

    If you want to access from your local business to your LAN network, you need to configure LAN-to-LAN tunnel.

  • How to put all through traffic the easy vpn client VPN server

    Hi people

    I want to ask you, how to put all of the server the easy vpn client VPN traffic through.

    I mean, I have a server vpn at home, and if I connect to the vpn from outside server, to be with an IP address of my home.

    There is the configuration up to now. Where is the problem?

    ROUTER1 #sh running-config

    Building configuration...

    Current configuration: 5744 bytes

    !

    ! Last configuration change at 19:51:18 UTC Wed Sep 4 2013 by cska

    !

    version 15.1

    horodateurs service debug datetime msec

    Log service timestamps datetime msec

    no password encryption service

    !

    ROUTER1 hostname

    !

    boot-start-marker

    usbflash0:CVO boot-BOOT Setup. CFG

    boot-end-marker

    !

    !

    !

    AAA new-model

    !

    !

    AAA authentication login ciscocp_vpn_xauth_ml_1 local

    AAA authorization ciscocp_vpn_group_ml_1 LAN

    !

    !

    !

    !

    !

    AAA - the id of the joint session

    !

    Service-module wlan-ap 0 autonomous bootimage

    Crypto pki token removal timeout default 0

    !

    Crypto pki trustpoint TP-self-signed-1604488384

    enrollment selfsigned

    name of the object cn = IOS - Self - signed - certificate - 1604488384

    revocation checking no

    !

    !

    TP-self-signed-1604488384 crypto pki certificate chain

    certificate self-signed 01

    3082022B 30820194 02020101 300 D 0609 2A 864886 F70D0101 04050030 A0030201

    2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30

    69666963 31363034 34383833 6174652D 3834301E 170 3133 30383239 31313539

    32395A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D

    4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 36303434 65642D

    38383338 3430819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101

    8100CD 57 F1436ED2 8D9E8B99 B6A76D45 FE56716D D99765A9 1722937C F5603F9F

    528E27AF 87A24C3D 276FBA1C A5E7C580 CE99748E 39458C 74 862C 2870 16E29F75

    7A7930E1 15FA5644 D7ECF257 BF46C470 A3A17AEB 7AB56194 68BFB803 144B7B10

    D3722BDD D1FD5E99 8068B77D A1703059 9F0578C7 F7473811 0421490D 627F25C5

    4 HAS 250203 010001A 3 53305130 1 130101 FF040530 030101FF 301F0603 0F060355

    551 2304 18301680 141B 1326 C111DF7F 9F4ED888 EFE2999A 4C50CDD8 06 12301

    03551D0E 04160414 1B1326C1 11DF7F9F 4ED888EF E2999A4C 50CDD812 300 D 0609

    2A 864886 04050003 81810096 BD0C2B16 799DB6EE E2C9B7C4 72FEAAAE F70D0101

    FF87465C FB7C5248 CFA08E68 522EA08A 4B18BF15 488D D53D9A43 CB400B54 8006

    CB21BDFB AA27DA9C C79310B6 BC594A7E D6EDF81D 0DB7D2C1 9EF7251B 19A 75403

    211B1E6B 840FE226 48656E9F 67DB4A93 CE75045B A986F0AD 691EE188 7FB86D3F

    E43934FA 3D62EC90 8F37590B 618B0C

    quit smoking

    IP source-route

    !

    !

    !

    !

    CISCO dhcp IP pool

    import all

    network 192.168.1.0 255.255.255.0

    DNS-server 195.34.133.21 212.186.211.21

    default router 192.168.1.1

    !

    !

    IP cef

    No ipv6 cef

    !

    Authenticated MultiLink bundle-name Panel

    license udi pid CISCO892W-AGN-E-K9 sn FCZ1530C209

    !

    !

    username privilege 15 secret 5 cska $1$ $8j6G 2sMHqIxJX8MQU6vpr75gp1

    !

    !

    !

    !

    !

    !

    crypto ISAKMP policy 1

    BA 3des

    preshared authentication

    Group 2

    !

    Configuration group customer isakmp crypto VPNGR

    vpngroup key

    DNS 212.186.211.21 195.34.133.21

    WINS 8.8.8.8

    domain chello.at

    pool SDM_POOL_1

    ACL 120

    netmask 255.255.255.0

    ISAKMP crypto ciscocp-ike-profile-1 profile

    match of group identity VPNGR

    client authentication list ciscocp_vpn_xauth_ml_1

    ISAKMP authorization list ciscocp_vpn_group_ml_1

    client configuration address respond

    virtual-model 1

    !

    !

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    !

    Profile of crypto ipsec CiscoCP_Profile1

    security association idle time 86400 value

    game of transformation-ESP-3DES-SHA

    set of isakmp - profile ciscocp-ike-profile-1

    !

    !

    Bridge IRB

    !

    !

    !

    !

    interface Loopback0

    192.168.4.1 IP address 255.255.255.0

    IP nat inside

    IP virtual-reassembly in

    !

    interface BRI0

    no ip address

    encapsulation hdlc

    Shutdown

    Multidrop ISDN endpoint

    !

    interface FastEthernet0

    !

    interface FastEthernet1

    !

    interface FastEthernet2

    !

    interface FastEthernet3

    !

    interface FastEthernet4

    !

    interface FastEthernet5

    !

    FastEthernet6 interface

    !

    interface FastEthernet7

    !

    interface FastEthernet8

    no ip address

    Shutdown

    automatic duplex

    automatic speed

    !

    type of interface virtual-Template1 tunnel

    IP unnumbered Loopback0

    ipv4 ipsec tunnel mode

    Tunnel CiscoCP_Profile1 ipsec protection profile

    !

    interface GigabitEthernet0

    Description Internet

    0023.5a03.b6a5 Mac address

    customer_id GigabitEthernet0 dhcp IP address

    NAT outside IP

    IP virtual-reassembly in

    automatic duplex

    automatic speed

    !

    wlan-ap0 interface

    description of the Service interface module to manage the embedded AP

    192.168.9.2 IP address 255.255.255.0

    ARP timeout 0

    !

    interface GigabitEthernet0 Wlan

    Description interface connecting to the AP the switch embedded internal

    !

    interface Vlan1

    no ip address

    Bridge-Group 1

    Bridge-Group 1 covering-disabled people

    !

    interface BVI1

    IP 192.168.1.1 255.255.255.0

    IP nat inside

    IP virtual-reassembly in

    !

    local IP SDM_POOL_1 192.168.4.3 pool 192.168.4.245

    IP forward-Protocol ND

    !

    !

    IP http server

    local IP http authentication

    IP http secure server

    overload of IP nat inside source list 110 interface GigabitEthernet0

    IP nat inside source static tcp 192.168.1.5 3389 interface GigabitEthernet0 3389

    IP nat inside source static udp 192.168.1.5 3389 interface GigabitEthernet0 3389

    IP nat inside source static tcp 192.168.1.5 21 interface GigabitEthernet0 21

    IP nat inside source static udp 192.168.1.5 21 interface GigabitEthernet0 21

    IP nat inside source static tcp 192.168.1.4 3389 interface GigabitEthernet0 3390

    IP nat inside source static udp 192.168.1.4 3389 interface GigabitEthernet0 3390

    overload of IP nat inside source list 120 interface GigabitEthernet0

    IP route 0.0.0.0 0.0.0.0 dhcp

    !

    exploitation forest esm config

    access list 101 ip allow a whole

    access-list 110 permit ip 192.168.1.0 0.0.0.255 any

    access list 111 permit tcp any any eq 3389

    access-list 120 allow ip 192.168.4.0 0.0.0.255 any

    !

    !

    !

    !

    !

    !

    !

    control plan

    !

    Bridge Protocol ieee 1

    1 channel ip bridge

    !

    Line con 0

    line 2

    no activation-character

    No exec

    preferred no transport

    transport of entry all

    transport output pad rlogin udptn ssh telnet

    line to 0

    line vty 0 4

    privilege level 15

    preferred transport ssh

    entry ssh transport

    transportation out all

    !

    Thanks in advance

    To do this you must make the following changes:

    (1) disable split Tunneling by deleting the ACL of your configuration of the client group.
    (2) enable NAT for VPN traffic by adding 'ip nat inside' to your virtual model of the client network to the ACL that controls your PAT.

    Edit: Theses are the changes to your config (also with a little cleaning):

    Configuration group customer isakmp crypto VPNGR

    No 120 LCD

    !

    type of interface virtual-Template1 tunnel

    IP nat inside

    !

    no nat ip inside the source list 120 interface GigabitEthernet0 overload

    !

    access-list 110 permit ip 192.168.4.0 0.0.0.255 any

    no access-list 120 allow ip 192.168.4.0 0.0.0.255 any

    Sent by Cisco Support technique iPad App

  • multi-site VPN with just the cisco vpn client

    Hello everyone

    Please I need your help.

    We have a headquarters office and up to 60 is BranchOffice, we want to create VPN network between its. so let's deploy 2 router cisco esy vpn server with HA (HSRP) at the Headquarters Office and all branches have Connection ADSL and they will use just the cisco vpn client to connect to the Headquarters Office.

    My question is: is it possible to do it just with the client vpn cisco without purchased for any exercise bracnh a cisco router to create an ipsec tunnel because it is so expensive?

    It depends on if the routers to offices can handle NAT with several internal VPN clients to 1 IP address. Most of the new material should be fine. Keep in mind the maximum limit of the VPN client, with 60 agencies and 5 people each of whom you are above the limit.

    Michael

    Please note all useful posts

  • Problems connecting to help connect any and the Ipsec VPN Client

    I have problems connecting with the VPN client connect no matter what.  I can connect with the Ipsec VPN client in Windows 7 32 bit.

    Here is my latest config running.

    Thank you for taking the time to read this.

    passwd encrypted W/KqlBn3sSTvaD0T

    no names

    name 192.168.1.117 kylewooddesk kyle description

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 192.168.1.1 255.255.255.0

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP address dhcp setroute

    !

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    boot system Disk0: / asa822 - k8.bin

    passive FTP mode

    DNS lookup field inside

    DNS domain-lookup outside

    DNS server-group DefaultDNS

    domain wood.local

    permit same-security-traffic intra-interface

    object-group service rdp tcp

    access rdp Description

    EQ port 3389 object

    outside_access_in list extended access permit tcp any interface outside eq 3389

    outside_access_in list extended access permit tcp any interface outside eq 8080

    outside_access_in list extended access permit tcp any interface outside eq 3334

    outside_access_in to access extended list ip 192.168.5.0 allow 255.255.255.240 192.168.1.0 255.255.255.0

    woodgroup_splitTunnelAcl list standard access allowed host 192.168.1.117

    inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.240

    outside_access_in_1 list extended access permit tcp any host 192.168.1.117 eq 3389

    woodgroup_splitTunnelAcl_1 list standard access allowed 192.168.1.0 255.255.255.0

    inside_nat0_outbound_1 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.240

    inside_nat0_outbound_1 to access extended list ip 192.168.5.0 allow 255.255.255.240 all

    inside_test list extended access permit icmp any host 192.168.1.117

    no pager

    Enable logging

    timestamp of the record

    asdm of logging of information

    Debugging trace record

    Within 1500 MTU

    Outside 1500 MTU

    mask pool local Kyle 192.168.5.1 - 192.168.5.10 IP 255.255.255.0

    IP local pool vpnpool 192.168.1.220 - 192.168.1.230

    ICMP unreachable rate-limit 1 burst-size 1

    ASDM image disk0: / asdm - 631.bin

    don't allow no asdm history

    ARP timeout 14400

    Global (inside) 1 interface

    Global 1 interface (outside)

    NAT (inside) 0-list of access inside_nat0_outbound_1

    NAT (inside) 1 0.0.0.0 0.0.0.0

    public static interface 3389 (indoor, outdoor) 192.168.1.117 tcp 3389 netmask 255.255.255.255 dns

    public static tcp (indoor, outdoor) interface 8080 192.168.1.117 8080 netmask 255.255.255.255

    public static tcp (indoor, outdoor) interface 3334 192.168.1.86 3334 netmask 255.255.255.255

    static (inside, upside down) 75.65.238.40 192.168.1.117 netmask 255.255.255.255

    Access-group outside_access_in in interface outside

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    dynamic-access-policy-registration DfltAccessPolicy

    WebVPN

    the files enable exploration

    activate the entry in the file

    enable http proxy

    Enable URL-entry

    SVC request no svc default

    AAA authentication http LOCAL console

    Enable http server

    http 192.168.1.0 255.255.255.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    outside_map interface card crypto outside

    crypto isakmp identity address

    crypto ISAKMP allow outside

    crypto ISAKMP policy 10

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    Telnet 192.168.1.0 255.255.255.0 inside

    Telnet timeout 5

    SSH timeout 5

    Console timeout 0

    dhcpd dns 8.8.8.8 8.8.4.4

    dhcpd lease 3000

    !

    dhcpd address 192.168.1.100 - 192.168.1.130 inside

    dhcpd allow inside

    !

    a basic threat threat detection

    host of statistical threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    allow outside

    SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 1 image

    enable SVC

    internal sslwood group policy

    attributes of the strategy of group sslwood

    VPN-tunnel-Protocol svc webvpn

    WebVPN

    list of URLS no

    internal group woodgroup strategy

    woodgroup group policy attributes

    value of server DNS 8.8.8.8 8.8.4.4

    Protocol-tunnel-VPN IPSec

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list woodgroup_splitTunnelAcl_1

    mrkylewood encrypted Q4339wmn1ourxj9X privilege 15 password username

    username mrkylewood attributes

    VPN-group-policy sslwood

    VPN - connections 3

    VPN-tunnel-Protocol svc webvpn

    value of group-lock sslwood

    WebVPN

    SVC request no webvpn default

    tunnel-group woodgroup type remote access

    tunnel-group woodgroup General attributes

    address pool Kyle

    Group Policy - by default-woodgroup

    tunnel-group woodgroup ipsec-attributes

    pre-shared key *.

    type tunnel-group sslwood remote access

    tunnel-group sslwood General-attributes

    address pool Kyle

    authentication-server-group (inside) LOCAL

    authentication-server-group (outside LOCAL)

    Group Policy - by default-sslwood

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the netbios

    inspect the rsh

    inspect the rtsp

    inspect the skinny

    inspect esmtp

    inspect sqlnet

    inspect sunrpc

    inspect the tftp

    inspect the sip

    inspect xdmcp

    Review the ip options

    type of policy-card inspect dns MY_DNS_INSPECT_MAP

    parameters

    !

    global service-policy global_policy

    context of prompt hostname

    call-home

    Profile of CiscoTAC-1

    no active account

    http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

    email address of destination [email protected] / * /

    http https://tools.cisco.com/its/service/...es/DDCEService destination address

    destination-mode http transport

    Subscribe to alert-group diagnosis

    Subscribe to alert-group environment

    Subscribe to alert-group monthly periodic inventory

    monthly periodicals to subscribe to alert-group configuration

    daily periodic subscribe to alert-group telemetry

    Cryptochecksum:6fa8db79bcf695080cbdc1159b409360

    : end

    asawood (config) #.

    You also need to add the following:

    WebVPN

    tunnel-group-list activate

    output

    tunnel-group sslwood webvpn-attributes

    activation of the Group sslwood alias

    Let us know if it works.

  • How to save the password to the Cisco VPN Client?

    Hello

    I use version 4.8 to connect to the VPN from my client, I would like to save my password so that I don't have to enter it each time.

    I've amended the FCP file to include:

    ! SaveUserPassword = 1

    and my password in UserPassword =, but it worked only once, after I restart it no longer works.

    Then I see the method to use the command-line vpnclient.exe to connect and provide the password as a parameter to the command:

    vpnclient connect user pwd

    But I got this error when you try to connect:

    Setting user password failed. User password is read-only.

    And the client always requests the password.

    Any ideas?

    Thank you

    The server sets the password save, you will not be able save locally unlessit is enabled on the server side. If the customer has an ASA, follows allows him under the group policy for VPN clients.

    allow password-storage

  • IP address of the IPSec VPN client did not get distributed via EIGRP

    We use an ASA for VPN remote access. He is running EIGRP redistribute static routes. When a client Anyconnect SSL connects, the SAA creates a static route for this client, and it gets redistributed via EIGRP. When an IPSec VPN client connects, the SAA creates a static route for this customer, but he isn't redisributed via EIGRP and so the client can not achieve anything. Why he would distribute a static created by an IPSec client?

    Thank you

    Have you set up IPP on dynamic Cryptography?

  • Function of automatic update for the IPsec VPN Client

    Hello.

    Do you have anyone ever tried the PIX / ASA ' feature IPsec VPN Client Auto-Update?

    (see also Document ID: 105606).

    He wants to make sure that I understand this right.

    The user will receive a popup of information telling him to download the latest version of the client? And then there start the update itself?

    If so, this would mean that the user must have the rights of full adminsitative using a laptop.

    From my point of view, full administrator rights on a laptop are prohibited - 100% and therefore the functionality would be totally useless.

    Anyone who can tell me whether I am good or bad?

    Best

    Frank

    Frank,

    You are right, if the computer desktop or labtop is completely locked regarding the installation of the software the customer won't be able to install it, they may be able to download from the link that you configured in ASA, once they connect to your server ASA RA but with regard to the installation user's machine needs rights profile appropriate to be able to install it.

    HTH

    -Jorge

Maybe you are looking for