The computer does not recognize my skycaddie is hung

Synchronization of caddie program is installed, but it seems that the computer does not recognize my skycaddie is hung

Original title: I can't get the computer to recognize my sky caddie - when I go to install a new device is not able to find it

Hello

 
 
1. the device is recognized in Device Manager? Is there a yellow exclamation point or question mark next to the device?
 
2. don't SkyCaddie connects to the computer via USB? If so, is he recognized initially until the software is installed?
3. do you receive any error messages?
4. What is the antivirus installed on the computer program?
 
If you connect the device via USB, I suggest you to change the USB port and check with the question.
 
 
 

Hardware devices do not work or are not detected in Windows
http://support.Microsoft.com/mats/hardware_device_problems/en-us
 
 
I suggest you provide more information about the issue so that we can better help you.
 
I also suggest you to see the link below for more option support about the issue.
 
 
 
 
I hope this helps.

Tags: Windows

Similar Questions

  • My computer cannot connect to the internet, the signal is excellent in the modem, but the computer does not recognize that there is a link.

    My computer cannot connect to the internet, the signal is excellent in the modem, but the computer does not recognize that there is a link. What could be wrong?

    Hello

    • What connection do you use?
    • What is a wired or wireless?
    • What happens when you try to start Internet Explorer?
    • You receive an error message?

    You can check these links:

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

    http://support.Microsoft.com/kb/956196

    Warning: Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings

  • the computer does not recognize the printer memory card reader. HP photosmart 7660 printer

    The computer does not recognize the memory card from camera. The printer recognizes the memory card. So I can't transfer photos unless the camera is connected via USB. The printer is HP Photosmart 7660. Any suggestions?  Driver has been updated ' 09 and MS says I have the latest version of the driver.

    Ron

    The computer does not recognize the memory card from camera. The printer recognizes the memory card. So I can't transfer photos unless the camera is connected via USB. The printer is HP Photosmart 7660. Any suggestions?  Driver has been updated ' 09 and MS says I have the latest version of the driver.

    Ron

    Microsoft did not your hardware - done HP.

    All support for it - regardless of your operating system - is the manufacturer of the equipment.
    http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?product=305364&LC=en&cc=us&DLC=en&lang=en&cc=us

  • I have an old version of Illustrator (9) and I can't install it on my computer.  The computer does not recognize the drive.  Is there a way to get around this?

    I'm trying to install Illustrator 9 on my PC and the computer will not recognize the disc.  Is there a solution to this?

    You could look to see if there is a download link in the links of kglad in answer 1 # here https://forums.adobe.com/thread/1930162

  • I recently had a new hard drive installed in my 2008 iMac. I'm trying to re - install office and the computer does not recognize my password. I tried all the passwords I can think of and nothing works and it wont let me continue

    I recently had a new hard drive installed in my 2008 iMac desktop computer, because right now I can't afford a new computer.   I am now under OS X El Capitan 10.11.4 and my password no longer works so that I can reinstall office microsoft for Mac.  I'm trying to change my password, but you must enter the old password and it does not recognize the password.  I tried every password I use and nothing works.  How can I change or get a new password?

    Reset the password.

    OS X 10.7 Lion, Mountain Lion, Yosemite 10.9 10.8, Yosemite 10.10 and 10.11 El Capitan

    Shut down the computer.

    Start the computer, and then press on and hold the command key and the R key to boot from the recovery partition.

    When you see the Apple logo, release the keys.

    Wait until the OS X Utilities window appears.

    Move the mouse pointer to the bar menu at the top of the screen, click on "Utilities" and select "Terminal".

    in the menu dropdown.

    Terminal window is displayed.

    TypeRegeditdans resetpassword and press enter on the keyboard.

    Reset Password Utility window will open.

    Leaving the Terminal.

    Select Macintosh HD, if not already.

    Select the user account in the menu popup box under "Select user account.

    Enter a new password.

    Re-enter the new password for the user.

    Enter a hint.

    Click on the Save"" button.

    Click  in the menu bar, and then select restart.

    Open a session.

    When Keychain dialog box appears, select "create new keychain".

  • Want to reinstall XP but the computer does not recognize the cd drive and does not allow for any installation.

    Accidentally deleted some system files and now the computer won't allow me to install anything. Tried to install a new cd player to replace a corrupt, but it does not recognize drive. All the driver and OS install CD. Help.

    Fix missing files:

    Try to run the checker system (CFS) files.  Press start, select run, type: SFC/scannow

    SFC will ask your installation disc (which you must have if you are going to re - install), put it in the drive when requested.  Leave the SFC to replace all missing or corrupt files.

    To resolve the startup problem:

    Check your BIOS Setup and make sure the optical drive is enabled and listed before the hard drive in the boot order.  When you start, there will be a message, "type any key to boot from the CD-ROM."  Type any key (execpt shift, shift caps lock, NumLock, etc) will cause the CD to be initialized in the installation program.  (I use the space bar, it's an easy target.)

    In addition, it would be useful to know a few more things: 1) what edition and service pack level of Windows XP you are running?  (2) what is the model and manufacturer of the optical drive, please?

  • installed the latest updates of windows 7... now the computer does not recognize my video files avi... says "format not supported".

    I have installed the latest updates (02/27/10) and when I open sony vegas to edit some files avi... they were offline... when I tried to read with windows media player it says format not supported... before when I played these files, they would not have to synchronize audio... it never happened with my other computer with Vista... system restore solved the problem of format not supported... but so far has caused this problem? and what about the problems of synchronization? the files seem to sync when played with the hp program...

    Hi derlonewolf,
     
    Because you performed a System Restore you would not be able to determine which update problem from occurring. You will have to wait for the update to your computer to determine the update that caused the problem. The update does not necessarily cause the problem to occur again. However, you can view the history of updates to updating history.
     
    1. open the control panel (all items view), and click the Windows Update icon.
     
    2. click on the link to view update history.
     
    3. to view the details of a single Windows Update-
     
    (A) select and right-click on a Windows Update list, and then click details.
     
    (B) click on close when finished.
     
    As far as the question of timing is concerened, you can scan SFC on your computer and check if the problem persists.

    Steps to perform a scan SFC:
     
    1. Click Start, click principally made programs, accessories, right-click Guest, and then click Run as administrator. If you are prompted for an administrator password or a confirmation, type the password, or click on allow
     
    2. type the following command and press ENTER:
    sfc/scannow
    [The command sfc /scannow. analysis of all protected system files and replaces incorrect versions with appropriate Microsoft versions.]
     
    A message appears indicating that "the system scan will start. Be patient, because the analysis may take some time
     
    3. If all the files require that a SFC replace will replace them. You may be asked to insert your Win7 DVD for this process to continue
     
    4. If all goes although you should, after the analysis, see the following message "Windows resource protection not found any breach of integrity.
     
    5. once the scan is finished, close the command prompt window, restart the computer and check.
     
    Check the link below for further guidance on scan SFC - mentioned
     
    You can also make manual updates instead of automatic updates and then see what are updates will be installed on the computer.

    See : http://windows.microsoft.com/en-us/windows7/Turn-automatic-updating-on-or-off

    Post back with the status

     
     
    Aziz Nadeem - Microsoft Support
  • I can't uninstall several programs to add and remove programs, due to a file finding.msi problem, if I can find myself, the computer does not recognize my file.

    I use:(Microsift XP, Service Pack 3 ou 4 maintenant je suppose, il a été récemment installé par MS Update.) X 86, 32-bit construction. Anyway, oddly enough since I got the virus, I had MSE was not woking for a few weeks, big I don't know if this is related to my problem. It was a kind of 'Trojan horse'. MSE new beta version is now in place and the work. But, the question is, why when I try to remove programs, many of them claim that the folder that contains the installation package ___.msi is missing and trying to find it, so when I find, he continues to say the same thing. I really need to get rid of some of these programs, can help you, I hope! I almost installed a Windows installation package 'day', but scared myself and thought I'd better ask the experts! Thanks for your precious time! Kina.

    Hello

    1. What are the programs you want to uninstall?
    2. who was the update that has recently been installed on your computer?
    3. What is the exact error that you receive when you try to uninstall programs?
    4 is this specific problem with some programs all programs you are trying to uninstall?
    5. have you made changes on the computer before this problem?
    You can run the fix - it mentioned in the following link.
    Solve problems with programs that cannot be installed or uninstalled
    http://support.Microsoft.com/mats/Program_Install_and_Uninstall/
    Please provide us with more information, so that we can help you further.
  • To install the new eSATA / SATA to USB 2.0 hard drive in an external enclosure but the computer does not recognize the drive in disk management

    I have an old computer with installed Microsoft Windows XP SP2 and 3.  I bought a new hard drive and also a new external hard drive for her case.  I have correctly installed the hard drive inside the enclosure, and I think that I have installed correctly (in the motherboard SATA port) eSATA port, according to the manufacturer's instructions.  I plugged everything... first eSATA, then power and power switch.  I restarted the computer, and I chose to analyze disks in disk management.  However, the new drive is not recognized.  The SATA port on the motherboard could not work or did I buy the bad, perhaps, hard drive enclosure for my system?  Or something related to the software?  Thank you.

    Hi Donnadream,

    Connect the hard drive to another port and check if that makes a difference

    Step 1: You can follow the steps mentioned in the article below, which deals with a similar question

    A computer that is running Windows XP cannot detect a USB, an Apple iPod flash drive or an external hard disk drive

    http://support.Microsoft.com/kb/925196

    Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
    How to back up and restore the registry in Windows
    http://support.Microsoft.com/kb/322756/

    Step 2: Download and install the latest drivers from the chipset of the computer or the manufacturer of the motherboard and check

    Step 3: Hard disk can be turned off in the BIOS; You may want to enable

    Important: Change BIOS (Basic input output system) /semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

    If the problem persists, it is a hardware problem, contact the manufacturer of the hard drive for a more specialized help

    Thanks and greetings

    Ajay K

    Microsoft Answers Support Engineer

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • How to uninstall a program, Kaspersky Pure 2.0 when the computer does not recognize it?

    I installed a trial version of Kaspersky Pure 2.0 and cannot uninstall it. This means that I can not download my new Norton security package. I get a message that the file installed is not found.

    Use the Kaspersky removal tool:

    Withdrawal tool for Kaspersky Lab products

    If you are running a 64-bit version of Windows, also check c:\Program Files and C:\Program (x 86).

    Also perform a clean boot:

    • Click Start
    • Type: MSCONFIG.
    • Press enter on your keyboard
    • On the general tab, click Selective startup.
    • Under Selective startup, clear the check box load startup items.
    • Click the Services tab, select the hide all Microsoft Services check box, and then click Disable all.
    • Click OK.
    • When you are prompted, click on restart.
    • After the computer starts, check if the problem is resolved.
  • My Firefox on my new install of the computer does not recognize the password of the previous computer files.

    I have a new computer running Windows 7 Professional. I installed Firefox and copied all the files in the Firefox profile on my old system to the new profile. All of my bookmarks, extensions, etc. are on the new system, but I got passwords with a master password, and none of it is there.
    I checked and key3 and logins.json files are in the profile and are the same size as the previous ones.
    How to activate passwords on the new system?
    Thank you

    OK - I have re-copied these two files in the new profile and it works now.

    Thank you
    Randy

  • Computer does not recognize the c200 player

    When I plug my c200 player in your PC with Windows Media Player running, the computer does not recognize it.  I check my computer and the drive does not appear there either.

    I took the c200 at Best Buy and they tried two different cables and their computer could not identify the player either.

  • Computer does not recognize the CD/DVD drive

    For these last days, my computer does not recognize the CD/DVD drive.  I have tried everything - publishers of registry, check the physical connections inside the computer, the system restore and install Fix - It programs.  However, the computer does not recognize this drive.  I also wonder if it is a hardware problem.  The light on the drive is a constant in green, and does not have the Open button.  And when I use the bent-paper-clip-in-the-little-hole and can open the drive, it will not read the disc.  Please advise...

    I fixed my problem with the BIOS operating system & not recognizing not not my DVD player to reinvest the solder on the motherboard.  You can find instructions on how to do it here: http://www.computerrepairtips.net/how-to-reflow-a-laptop-motherboard/

    There was a little crazy with my video drivers when I started first, but everything works after resetting the BIOS by default.

  • Why my computer does not recognize the CD when inserted?

    I am trying to install a software on CD, but the computer does not recognize it.  I tried even my audio CD but they is also not recognize it.

    Hello

    Follow these steps to remove corruption and missing/damaged file system repair or replacement.

    Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

    sfc/scannow

    How to fix the system files of Windows 7 with the System File Checker
    http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

    Then run checkdisk (chkdsk).

    How to run check disk in Windows 7
    http://www.SevenForums.com/tutorials/433-disk-check.html

    ==========================================================

    After the foregoing:

    References to Vista also apply to Windows 7.

    Step 1: Please do all the same underneath if you did some before as is often total
    a process that solves the problem.

    Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
    Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
    RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
    below.

    Then, work your way through these - don't forget the drive might be bad, could be a coward
    cable or slight corrosion on the contacts (usually for a laptop) and other issues.

    Your CD or DVD drive is missing or is not recognized by Windows or other programs
    http://support.microsoft.com/kb/314060 - a Mr Fixit

    Try this fix manually if the Fixit 314060 does not work
    http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

    Your CD or DVD drive is missing or is not recognized by Windows or other programs-
    a Mr Fixit
    http://support.Microsoft.com/kb/982116

    The DVD player does not work after installing Windows 7
    http://support.Microsoft.com/kb/975270/

    The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
    Windows Vista
    http://support.Microsoft.com/kb/929461

    When you insert a CD or a DVD, Windows Vista may not recognize the disc
    http://support.Microsoft.com/kb/939052

    Your CD or DVD drive cannot read or write media - A Mr Fixit
    http://support.Microsoft.com/GP/cd_dvd_drive_problems

    CD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
    Setup after booting from the DVD (AHCI)
    http://support.Microsoft.com/kb/952951
    Drive CD - R or CD - RW Drive is not recognized as a recordable device
    http://support.Microsoft.com/kb/316529/

    Hardware devices not detected or not working - A Mr Fixit
    http://support.Microsoft.com/GP/hardware_device_problems

    Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
    ends. Remove and replace, do not just tight. For laptops, you can often clean power and
    contacts data with a pencil eraser.

    Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
    manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

    ===============================

    Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
    Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
    do it right.

    Did you follow the Troubleshooting Guide for the reader who still does not work? There are
    the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

    Check with your Maker system and a device for the two possible firmware updates and the
    correct registry entries for your car.

    Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
    as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
    the parameters.

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

    -----------------------------------------------------------------------

    You can probably find more info here and maybe even the exact registry settings for your
    CD/DVD drive someone with the same model.

    Forums - a lot of expert real help
    http://Club.myce.com/

    CD/DVD units
    http://www.myce.com/storage/

    Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
    nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

    DevManView - free - an alternative to the standard Windows Device Manager, which displays
    all devices and their properties in flat table, instead of the tree viewer
    http://www.NirSoft.NET/utils/device_manager_view.html

    I hope this helps.

  • Re: DVD recorder has changed and the laptop does not recognize

    I had to change my Toshiba Qosmio F20 portable recorder.
    Now, the computer does not recognize.

    I installed a DVD burner Sony Optiarc AD - 7590 IDE.
    I heard that the problem may be in the BIOS, I have the latest TOSHIBA for this laptop (which is installed V.1.40 2007) and the recorder comes with the manufacturing date of 2009.

    I currently use Windows 7 on this computer.
    Is it only possible for the computer recognizes it, "any driver or driver I install?

    Hello

    Talking about this laptop doesn't recognize, do you mean on the Bios or Device Manager or both?

Maybe you are looking for