The computer freeze - / restarts-/ BSOD.

Similar Questions

• Unable to start the computer - boots of BSOD

  Dell Dimension 210/9200c Windows XP Pro SP3 desktop

  Here's what I spent...

  Start-up, enter the admin password.

  Floppy drive seek failure

  Strike F1 key to continue, F2 to run the utility series

  If I choose the F1...

  Loading PBR for descripto 2... In fact.

  Playing a disc error has occurred

  Press CTRL + ALT + DELETE to restart

  I press CTRL + ALT + DEL and it leads to FAILURE to SEEK the FLOPPY DISKETTE.

  If I choose to F2, it goes to creating useful and I don't know what to try to change the problem.

  If I press F12 and go to the start menu...

  SafeMode to start the BSOD

  I tried to boot from the CD and use my recovery CD and the result was...

  Window, set up ran with the establishment is responsible (file exchange...), then he went up to the game starts windows.

  Here's what came...

  A PROBLEM HAS BEEN DETECTED AND WINDOWS HAS SHUT DOWN TO PREVENT DAMAGE.

  IF IT IS THE FIRST TIME YOU'VE SEEN THIS STOP ERROR... RESTART YOUR COMPUTER

  CHECK FOR THE PRESENCE OF VIRUS.  REMOVE ANY NEWLY INSTALLED HARD DRIVES OR HARD DRIVE CONTROLLERS.

  CHECK THE DRIVE FOR THE CORRECT AND COMPLETE CONFIGURATION

  RUN CHKDSK/F TO CHECK FOR HARD DRIVE CORRUPTION, AND THEN RESTART

  TECHNICAL INFO:

  STOP: 0X0000007B (0XF78DA63C, 0XC0000034, 0X00000000, 0X00000000)

  I can't the system to start.  I haven't added hardware or software.  I think that the computer has restarted after downloading some updates, but I can't to start or restore system. What can I do?

  Yes, I can get to this screen.  After you have clicked on enter, it looks like this:

  SET UP WINDOWS

  __________________

  __________________

  downstairs "SET UP IS LOADING FILES (*)...

  Then it turns down in "SET UP START WINDOWS"

  Then, it goes straight to the BSOD.

  I tried several times and he always goes for the BSOD.

  In the menu Setup, I ran a hard drive diagnostic and it showed this:

  "RUNNING HARD DRIVE DIAGNOSTICS, PLEASE WAIT...

  DRIVE 0: ST3320620AS

  IN CASE OF FAILURE.  RETURN CODE: 7

  Is this to say that the HD is shot?

  Your hard drive may or may not be at fault. Error code 7 could mean just corrupted hard disk controllers. This could also be the reason for the bsod.

  Enter your bios and follow the instructions below.

  1. start-up (Dell logo), press F2 to enter the BIOS

  2. expand the section "readers".

  3. go in "SATA Operation."

  4 change that "RAID Auto/AHCI" to "RAID Auto / ATA.

  Furthermore, if your bios does not have this option simply switch from SATA IDE mode.

• "Windows updates were not be properly configured and restoration of changes." The computer freeze

  I have a laptop Dell inspiron 1501 with windows vista on it.

  I don't have the disc of windows Vista DVD you are referring to, I have never recived a Dell I bought the computer on the internet with vista already installed.

  My problem is that, with respect to the windows updates, I get a message saying "Windows have been developed to date not be properly configured and restoration of changes". I have 51 updates pending, 47 of these updates is equivalent to 170 MB.

  As a result of these updates, I think it's the cause of my freezing computer once I have connected and I have to restart only having do not 2 - 3 times.

  When the computer "freezes" the cursor does not move throughout the scene, none of the keys works, including Manager tasks etc., the only thing that works is to turn the computer off. Sometimes, there is a beep, beep once the computer crashes.

  Over 95% the updates I have try have 'no '.

  I'm lost as how to how to repair?

  All good suggestions welcome to solve this problem, the simpler the better... I don't want to have to buy a new computer... If I won't Dell... and I'll have to get the windows disc... most solutions here seem to require it...

  Hi AL0001,

  Run the chkdsk command to check that there are no problems with your hard drive. To run the disk check, follow these steps:

  1. Restart your computer and immediately press the F8 key until you reach the menu Advanced Boot Options.
  2. Select Mode safe mode with command prompt.
  3. At the command prompt, type chkdsk/r (there is a space between the k and /)

  Meanwhile, check the Dell website to see how you can get a recovery disk in case you need to recover Windows.

• The computer was restarted after a bugcheck. The bugcheck was: 0x00000001 (0 x 0000000000000000, 0 0000000000000001, 0x00000000742d2e09, 0xfffff8800aa00b60).

  Computer BSOD'd 2 x today.  The event log States:

  The computer was restarted after a bugcheck. The bugcheck was: 0x00000001 (0 x 0000000000000000, 0 0000000000000001, 0x00000000742d2e09, 0xfffff8800aa00b60).

  LEAPC_INDEX_MISMATCHERREUR (1)
  This is an internal error in the kernel. The most common reason to see this
  error checking is when a file system or a driver has several mismatched
  visits to disable and re-enable the TTB. The data key item is the
  Thread-> CombinedApcDisable field. It's two separate 16-bit
  the SpecialApcDisable and the KernelApcDisable fields. A negative value
  either indicates that a driver has disabled APC normal or special
  (respectively) without reactivation; a positive value indicates that
  a driver allowed normal or special APCS (respectively) too many times.
  Arguments:
  Arg1: 00000000742d2e09, address of function or worker system call
  Arg2: 0000000000000000, thread-> ApcStateIndex
  Arg3: 0000000000000001 (thread-> SpecialApcDisable < 16)="" |="" thread-=""> KernelApcDisable)
  Arg4: fffff8800aa00b60, call type (system call 0-, 1 - routine worker)

  Debugging information:
  ------------------

  TRIAGER: Could not open the file of triage: e:\dump_analysis\program\triage\modclass.ini, error 2

  FAULTING_IP:
  + 0
  00000000' 742d2e09?              ???

  DEFAULT_BUCKET_ID: WIN7_DRIVER_FAULT

  BUGCHECK_STR: 0X1

  Nom_processus: ccSvcHst.exe

  CURRENT_IRQL: 0

  LAST_CONTROL_TRANSFER: from fffff800032841a9 to fffff80003284c00

  STACK_TEXT:
  fffff880 '0aa00928 fffff800' 032841a 9: 00000000'00000001 00000000' 742d2e09 00000000'00000000 00000000'00000001: nt! KeBugCheckEx
  fffff880 '0aa00930 fffff800' 032840e0: 00000000'00001 c 48 00000000' 0780e0a8 00000000' 0780e970 00000980'00000018: nt! KiBugCheckDispatch + 0 x 69
  fffff880 '0aa00a70 00000000' 742d2e09: 00000000'00000000 00000000'00000000 00000000'00000000 00000000'00000000: nt! KiSystemServiceExit + 0 x 245
  00000000' 0780e9b8 00000000'00000000: 00000000'00000000 00000000'00000000 00000000'00000000 00000000'00000000: 0x742d2e09

  STACK_COMMAND: kb

  FOLLOWUP_IP:
  NT! KiSystemServiceExit + 245
  fffff800'032840e0 4883ec50 sub rsp, 50 h

  SYMBOL_STACK_INDEX: 2

  SYMBOL_NAME: nt! KiSystemServiceExit + 245

  FOLLOWUP_NAME: MachineOwner

  MODULE_NAME: nt

  Nom_image: ntkrnlmp.exe

  DEBUG_FLR_IMAGE_TIMESTAMP: 5684191c

  FAILURE_BUCKET_ID: X64_0x1_SysCallNum_4_nt! KiSystemServiceExit + 245

  BUCKET_ID: X64_0x1_SysCallNum_4_nt! KiSystemServiceExit + 245

  These accidents were related to the corruption of memory (probably caused by a driver).

  Run these two tests to check your memory and find which driver is causing the problem.  Launch auditor.  You don't need to run memtest again unless the auditor is not the cause, or you want to.

  If you are overclocking anything reset by default before running these tests.
  In other words STOP! If you don't know what it means that you're probably not  
  
  
  
  
  1-Driver Verifier (for full instructions, see our wiki here)
  
  2-Memtest. (You can learn more about running memtest here)

  Former pilot who need update

  dne64x.sys (Cisco VPN driver since 2008)

  If you continue to plant I remove Symantec and using MSE instead

  Symantec is a common cause of BSOD.

  
  
  I remove and replace it with Microsoft Security if you are using Windows 7 and if you win 8 or higher, use the built-in Defender.
  
  http://us.Norton.com/support/kb/web_view.jsp?wv_type=public_web&docURL=20080710133834EN
  http://www.Microsoft.com/security_essentials/

  Use it to Norton 360 http://Symantec.pcperformancetools.com/Norton-360-how-to-uninstall.html 

• The computer was restarted after a bugcheck.

  I get the following BSOD and error message resulting approximately every 10 days.  It seems more prevalent when I try to play a video from the browser, but it happened when I am just browsing the internet.

  

  The computer was restarted after a bugcheck.  The bugcheck was: 0 x 00000116 (0xfffffa80080be380, 0 x 0000000000000002, 0xfffff88003c92aec, 0 x 0000000000000000). A dump was saved in the: C:\Windows\MEMORY. DMP. Report ID: 020715-40185-01.

  You can download a zip file containing all my files current mini dump from here:

  https://onedrive.live.com/redir?RESID=6CBE36721A006FAF! 110 & authkey =! AMEI8sjZRhqgkT4 & ithint = the file % 2czip

  Any help would be appreciated.

  Thank you

  Bill

  Bill

  These accidents are called BCC116 and are associated with your video subsystem.  Please follow the instructions of this wiki

  
  

• The computer was restarted after a bugcheck. The bugcheck was: 0x0000003b (0xfffff880113022ec, 0xfffff88008266950, 0x00000000c0000005, 0 x 0000000000000000).

  The beginning of this month, I have built me a new platform game and installed Win 7 HP. everything worked very well at 18. I was just browsing the internet, and all of a sudden my computer froze for a second, then went to the BSOD. Inside, I saw that it was a "memory dump". He did 3 times the same day where I just internet browsing. Upset A, looked autour online and I've seen where people have said that it could be caused due to the update software. So I updated what he needed and then with my day. Well, it happened earlier this morning. I decided to look in my event viewer and see if I could find what is the problem. I found a mistake:

  The computer was restarted after a bugcheck.  The bugcheck was: 0x0000003b (0xfffff880113022ec, 0xfffff88008266950, 0x00000000c0000005, 0 x 0000000000000000). A dump was saved in the: C:\Windows\MEMORY. DMP. Report ID: 072414-16614-01.

  So I decided to call Microsoft and their solution to the problem was "reinstall Windows! Reinstall Windows! "WHAT! REINSTALL WINDOWS! It will take me 2 DAYS to get my computer to the way I want it with all my programs, movies, music. I know that there is another solution to this problem. I want to know the cause of the BSOD. So I was reading around and I've seen where people would say upload the file to dump memory to Skydrive and someone will look into it to find a problem. Well, I downloaded the .dmp file to my Onedrive and I hope and pray someone can read and help. (https://onedrive.live.com/redir?resid=E4B0911EE97A02C1 107 & authkey =!) AAR8h7CfZxBp7aw & ithint = the file % 2cdmp) I initially thought it was a problem of RAM because he said that it was a picture of 'memory '.

  Help, please.

  Thank you!

  Original title: Blue Screen of Death on the new computer. Help, please

  Update of these older drivers may help.

  Update Corsair Link the software to version 2.6.5214 Installer
  http://www.Corsair.com/en-us/support/downloads

  BELKIN F7D4101 Play Wireless USB Adapter firmware update

  http://www.Belkin.com/us/support-article?articleNum=4726

• HELP PLEASE! The computer was restarted after a bugcheck.

  I was hoping that someone could help me understand what is the cause. This has happened for the past 2 days on one of our servers. The server is a Windows Server 2008 R2 computer.

  That's the message in the event viewer:

  The computer was restarted after a bugcheck.  The bugcheck was: 0 x 00000050 (0 x 0000000000000001, 0xfffff800016d40cc, 0xffffffffffffffd0, 0 x 0000000000000000). A dump was saved in the: C:\Windows\MEMORY. DMP. Report ID: 030313-9156-01.

  This is the message that is displayed on windows re-opening after the accident:

  Signature of the problem:
  Problem event name: BlueScreen
  OS version: 6.1.7601.2.1.0.272.7
  Locale ID: 1033

  More information about the problem:
  BCCode: 50
  BCP1: FFFFFFFFFFFFFFD0
  BCP2: 0000000000000001
  BCP3: FFFFF800016DE0CC
  BCP4: 0000000000000000
  OS version: 6_1_7601
  Service Pack: 1_0
  Product: 272_3

  Files helping to describe the problem:
  C:\Windows\Minidump\030413-8765-01.dmp
  C:\Temp\WER-83783546-0.SysData.XML

  Hello

  Resolve errors stop (blue screen) in Windows 7 - has a section for if you can or cannot start Windows.
  http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

  For BlueScreen troubleshooting methods using BlueScreenView and MyEventViewer see my
  answers if this thread - top 3 RESPONSES (+ 1 other).

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-system/sometimes-i-get-a-blue-screen-when-using-IE-8/c675b7b8-795f-474d-a1c4-6b77b3fcd990

  We can analyze the minidumps if make you it available to the SkyDrive or another file
  sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
  for the office or in the Documents folder and download them from there.

  ZIP or download the content of the C:\Windows\minidump

  Use SkyDrive to upload collected files
  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  --------------------------------------------------------------------------------------------------

  BCCode: 50 0 x 00000050

  References to Vista also apply to Windows 7.

  Have you recently added any hardware? Have you updated a driver just before
  These began? (Check control panel - updates of Windows to see if all drivers
  have been updated it there all the time, it started) main likely culprits are video
  pilot, other great drivers, memory and antivirus/antispyware/security products
  could be faulty as well as reader questions.

  Use the troubleshooter below and refer to the following message for pilots and
  memory when you get these sections and then return of the disease.
  game needed.

  BCCode: 50 0 x 00000050

  Bug Check 0 x 50: PAGE_FAULT_IN_NONPAGED_AREA

  PAGE_FAULT_IN_NONPAGED_AREA bug control has a value of 0 x 00000050. This indicates that invalid system memory was referenced.

  Important info if you received a STOP Code

  If you received a blue error screen, or a stop code, the computer stopped abruptly to protect against data loss. A hardware device, its driver or software might have caused this error. If your copy of Windows is shipped with your computer, contact your computer manufacturer. If you have purchased
  Windows separately from your computer, Microsoft provides support. To find contact information for Microsoft or the manufacturer of your computer, Contact Support.

  If you have experience with computers and try to recover from this error, follow the steps in the Microsoft article solution STOP (blue screen) errors in Windows.

  These actions could prevent a mistake like this does not happen:

  1. Download and install updates for your computer from Windows Update device drivers.
  2. Scan your computer for computer viruses.
  3. Check your hard drive for errors.

  PAGE_FAULT_IN_NONPAGED_AREA parameters

  The following settings are displayed on the blue screen.

  Parameter	Description
  1	The referenced memory address
  2	0: Read operation 1: Write operation
  3	Address that referenced memory (if known)
  4	Reserved

  If the driver responsible for the error can be identified, its name is printed on the blue screen and stored in memory location (PUNICODE_STRING) KiBugCheckDriver.

  Cause

  Bug control 0 x 50 usually occurs after the installation of a faulty hardware or installation failure of material (usually associated with defective RAM, either main memory, L2 RAM or RAM video cache).

  Another common cause is a defective system service installation.

  Antivirus software can also trigger this error, as can a corrupted NTFS volume.

  Resolution

  
  Fix a defective hardware problem: if the material has been added to the system recently, remove it to see if the error recurs. If the hardware failure existing, remove or replace the faulty component. You must run the diagnostics of material provided by the manufacturer of the system. For more information about these procedures, see the manual of your computer.

  
  Fix a defective system service: disable the service and confirm that this resolves the error. If so, contact the manufacturer of the system service on a possible update. If the error occurs during the system startup, restart your computer, and then press F8 to menu mode characters that displays the choice of operating system. In the Windows Advanced Options menu that results, select the last known good Configuration option. This option is most effective when a pilot or a service is added at a time.

  
  A problem of antivirus software: disable the program and confirm that this resolves the error. If this is the case, contact the manufacturer of the program about a possible update.

  
  Fix a corrupted NTFS volume: run Chkdsk /f /r to detect and repair disk errors. You must reboot the system before the start of the analysis of disk on a system partition. If the SCSI hard disk, check the problems between the SCSI controller and the drive.

  Finally, check the system log in Event Viewer for additional error messages that might help determine the device or driver that generated the error. Disable the cache in memory of the BIOS might also resolve it.

  Remarks

  In general, this address is in the released memory or simply not valid.

  This cannot be protected by a try - except Manager - it can only be protected by a probe.

  BCCode: 50 0 x 00000050<-- read="" this="">
  * 1095.html? order = votes http://www.faultwire.com/solutions-fatal_error/page-fault-in-NONPAGED-Area-0x00000050-

  =========================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
  program generates cbs.log Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers under Windows 7 (updated drivers manually using the methods above
  It is preferable to ensure that the latest drivers from the manufacturer of system and device manufacturers are located)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  Stop Windows 7 to automatically install device drivers
  http://helpdeskgeek.com/Windows-7/stop-Windows-7-from-automatically-installing-device-drivers/

  How to disable automatic driver Installation in Windows 7 / Vista
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/

  Turn off Windows Update Device Driver search prompt in Windows 7 / Vista (for professionals,
  Ultimate and Enterprise)
  http://www.AddictiveTips.com/Windows-tips/disable-Windows-Update-device-driver-search-prompt/

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials/3413-repair-install.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• HP Officejet 4630 portable printer: HP Officejet 4630 printer does not print until the computer is restarted

  When I send a document to the printer; It shows in the print queue, but does not print.  When I restart my computer, the document will print.

  The same thing happens whenever I have send a document to the printer.  I have a WiFi connection from my laptop to the printer.  The blue icon on the printer lights indicating that plugged.

  Why does only work when the computer is restarted?  I ran the HP Support Assistant, and it does not find the printer; even if the printer seems to find the computer once I restarted the computer.

  It's embarrassing to say and I'm not very technical interest.  Any suggestions will be greatly appreciated.

  Hi @Maggie78

  Thank you for your patience.

  You can try the following:

  Creating a TCP IP port
  
  1. print a Configuration Page to get the printer IPv4 address (you can also tap on the icon wireless on the front panel of your printer to obtain the IP address)
  2. on your PC, go to the Panel control, devices and printers, right-click the printer and on the left, click printer properties, select the Ports tab.
  3. click Add Port, select the Port TCP/IP Standard, then New Port and follow the instructions in the wizard.
  4. Enter the IP address of the printer.

  Note that you can ALWAYS go back to the original port the HP software installed by selecting the HP port on the Ports tab (in the properties of the printer)

  Hope that helps!

• Lenovo u310, when raid enable the computer is restart auto

  Hello

  I have lenovo u310, when raid is activating the computer is restart auto

  and cannot take the step to enter in the configuration, very fast often resetting.

  but when I get home IM disconnect the hard drive I can enter in setup and change comptiable RAID, then im trying to boot blue screen and pc windows it reboot auto.

  What is the problem?

  Thank you.

  OK this is what I've done, raid is not possible, I don't know why...

  so I put on compatible and install a fresh Windows 7 from a usb flash drive and it will solve the problem.

• colored lines appear on the screen and the computer freezes with W7

  This happened several times since I got this computer in December.  Lines of color will appear in horizonally across the screen and the computer freezes.  After I have turn it off and start it again, there is no problem.  But is it a problem waiting for one big from appearing in the future?

  If this is a new computer, take it back where you got it because it will still be under warranty.
  Could be something from the graphic card, monitor etc. TaurArian [MVP] 2005-2010 - Update Services

• START WINDOWS VISTA ERROR "the computer restarted unexpectedly or encountered an unexpected error." Windows Setup cannot continue. To install Windows, click "OK" to restart the computer, and restart the installation.

  I have a portable Gateway that will not start, but rather when I turn on the laptop, it gives me a box of caption read "the computer restarted unexpectedly or encountered an unexpected error." Windows Setup cannot continue. To install Windows, click "OK" to restart the computer, and restart the installation. I bought the recovery CD gateway and even made the recovery discs offered by Microsoft, but nothing helped. Or recovery CD were no help. I am running Windows Vista. Any suggestions?

  I have a portable Gateway that will not start, but rather when I turn on the laptop, it gives me a box of caption read "the computer restarted unexpectedly or encountered an unexpected error." Windows Setup cannot continue. To install Windows, click "OK" to restart the computer, and restart the installation. I bought the recovery CD gateway and even made the recovery discs offered by Microsoft, but nothing helped. Or recovery CD were no help. I am running Windows Vista. Any suggestions?

  Hey PeLon416

  If you have problems with the gateway recovery process, you will need to contact Gateway

  It's their recovery process not microsofts

  You may have a hardware problem

  support of bridge at the link below

  http://support.gateway.com/support/default.aspx

  Walter, the time zone traveller

• roar of hard disk and the computer freezes for a few seconds

  My hard drive makes a sound whirring for a few weeks now and when I type in emails or messages like this, the computer freezes for a few seconds. Any ideas how to fix this?

  A desktop computer. Your problem could be overheating.

  You must remove the side panel right and remove dirt dust bunnies fans. Also, make sure that all the fans are working. Safety switch the computer off and pull the power cable before removing the side panel. You can then move the computer backon and check that the fans are working.

  Then, turn off the computer and some time for that cool. It is best to use a wrist band, which you set on the casing of the computer to you the earth before touching anything inside the envelope. You can buy one in a store of computer accessories. Static electricity can damage a motherboard if you don't take precautions.

  Then, you use a small brush to remove the sheep of dust around the fan on the processor. I used an electric razor, cleaning brush. I use an Air blower to clean the power supply fan. An air Duster is also useful fopr cleaning keyboards.

  Removal of the dust bunnies should reduce the noise that makes your computer. It can also reduce overheating, which can lead to errors of Blue Screen of Death.

  Another way to check the hard disk to see if it is overheating is to use HD Tune 2.55 (free):
  http://www.hdtune.com/download.html

  You have to scroll the page to see the freeware version.

• Unable to complete the installation of windows vista, error message "Windows cannot configure one or more system components to install Windows, restart the computer, and restart the installation.

  I'm install windows vista Ultimate edition in my new laptop, but during the installation stage 'completion', the prompt message as "Windows cannot configure one or more system components to install Windows, restart the computer, and restart the installation", but my new laptop was no install any OS before, please help

  tan7655,
  If I read this correctly, you have a portable computer that do not have an operating system on it.  You try to install Vista and get the error.
  You've restarted the Vista installation?  So then you get the same error? If you have tried to install more than once and continue to receive this error, check that the laptop is capable of Vista?  You may need to check with the manufacturer of the laptop to see if it is able to support Vista. Mike Microsoft responds to the technical support engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• When you delete a file in Vista, the dialog box remove does not close until the computer is restarted

  When you delete a file in Windows Vista, the dialog box remove don't close until the computer is restarted. It is sometimes possible to remove it by closing tha task list. When this is done, the Explorer is closed and restarted.

  Hi Brian,.

  (1) since when are you facing this problem?

  (2) remember to make changes?

  Method 1: Run the fixit available in the link below and check if that makes a difference

  Difficulty of broken desktop shortcuts and common system maintenance tasks

  
  Note: Fixit would attempt to recover bad sectors on the hard disk, in the course of this process there are chances of data loss from that particular area.

  Method 2: If a Protection of resources Windows (WRP) file is missing or is damaged, Windows may not behave as expected. Auditor of file system (CFS) scan to fix all of the corrupted system files. To do this, follow the steps mentioned in the link below:

  How to use the System File Checker tool to resolve missing or damaged on Windows Vista or Windows system files

  http://support.Microsoft.com/kb/929833

  Method 3:  Select the boot and then check if the problem persists

  Follow step 1 in the link below,
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  Important: n ' forget not to put the computer to a normal startup follow step 7 in the link.

• When I am working on my desktop HP, the computer freezes. Nothing works (keyboard or mouse). The screen becomes sometimes paler.

  When I am working on my desktop HP, the computer freezes. Nothing works (keyboard or mouse). The screen becomes sometimes paler. And the only way to resolve the pbobleme temporarily to stop temporarily the computer weighing on the button of the tower.

  Hi Louis,.

  Please select your language from the drop-down menu above to post your question in the language of your choice. The forum in which you've posted is for English only. If you can't find your language above, support for additional international sites options are by following the link below:

  http://support.Microsoft.com/common/international.aspx

  Thank you