The CRIO-9022 software installation
Anyone can help with installing Software NI 9022 by MAX
I connect OR cRIO-9022 with an Ethernet.
I was faced with a time-out error and saying that whether online or not, to the extent of the im concern its connected in safe mode as he always has no software in it.
Please see the attached file.
It is probably a detail of networking.
It seems that you have a link-local address on your cRIO (169.x.x.x) which means that you should always have your computer configuration using DHCP. If you have a static IP address on your computer, try to return to "obtain an IP address automatically".
If this does not work, I will try to set a static IP address on your PC to install the software and the cRIO. Once you get the cRIO software installed, you can switch everything back to DHCP.
Find instructions here:
http://www.NI.com/gettingstarted/setuphardware/CompactRIO/firstuse.htm
Kurt
Tags: NI Hardware
Similar Questions
-
netBT.sys replacement files viruses
Recently, I ran an anti-virus and learned that my netBT.sys file was corrupted. The anti-virus software installs this file but now my internet does not work. I guess I have to replace this file, but don't know how. I see that I need to use my windows XP CD but my CD drive is broken. How can I go about replacing this file?Thanks in advance
Hi DonMendigo,
Follow the suggestions below for a possible solution:
Method 1: Try the SFC (System File Checker) scan on the computer.
To run the System File Checker tool, follow these steps:
a. click Startand type cmd in the box start the search.
b. right click on cmd in the list programs, and then click run as administrator.
c. If you are prompted for an administrator password or a confirmation, type your password or click on continue
d. at the command prompts, the following line and press ENTER:
sfc/scannow
See also:
Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe)
http://support.Microsoft.com/kb/310747
File system (CFS) Checker
Method 2: If you are still unable to connect to the internet, then follow the article in the Microsoft Knowledge Base and check.
Programs Internet in Windows XP cannot connect to the Internet via a connection to wide band
http://support.Microsoft.com/kb/307164
I hope this helps.
-
Remove the installation files unpacked after the C7200 series Software Installation?
After that my printer (Photosmart C7280) has disappeared from the list of printers, I was tryilng to reinstall the software. Whenever I try, however, the installation package décompacte files, but does not delete them after installation (or after the installation fails). I have now no more room on my hard drive.
How to remove unnecessary files from these 'unwrapped' after installation? Where they were unpacked.
Thanks for any help, it's terribly frustrating!
If you use Windows files will be generally placed in a folder directory in a subdirectory with 7z...
To find these click Start, my computer and in the address bar type "%temp%" without the quotes. Search the directories starting with 7z at this stage. You can remove directories full 7z *.
-
Connect mobile NI 9144 to the cRIO 9022
Hi homer210788,
EtherCAT is a deterministic communications protocol, so it is not all real way to communicate wirelessly with the controller and 9144. Out of curiosity, what is your application, and why do you want to make wireless?
-
FPGA. What tool xilinx for Crio-9022 &; 9030
Hello. I will be compiling the programs of fpga on the Crio-9022 and 9030. You need Xilinx different compilers to do the task?
With the help of LV ver14
CRIO-9022 requires xilinxs 14.7 tool?
CRIO 9030 requires the xilinx tools vivado 2013.4?
Thank you
Yes, it's because of the different FPGA series located on the backplane of the 9022 and 9030 cRIOs. You can see this KB and this KBto see below why.
-
Nobody knows exactly what this update: Intel Chipset Software Installation Utility, v.9.1.1.1019, A01 addresses? What fixed it? I ask his stated as critical.
Detailed descriptionWant to save time? You are not sure if you need this file?
Run this easy to use Intel® Driver Update Utilityand it will be 'automatically' you tell if you need to update your chipset INF file and if so, will prompt you to install and you're done. This will save you a lot of time not only on your chipset download but the most common files needed for your system.
Name changes:
Intel® Chipset Device Software is the new name of the Intel® Chipset Software Installation Utility; We will see this name when you run the installation package.About this file/download:
Intel® Chipset Device Software installs of Windows INF files. An INF file is a text file that provides the operating system of the information on a piece of hardware on the system. In the case of the current Intel Chipset Device Software, this information is primarily the name of the product for the piece of hardware. This allows the operating system to show the correct name for this piece of hardware in Device Manager.* Important *.
Intel Chipset Device Software installs not AGP or USB drivers. DO NOT DOWNLOAD THIS UTILITY IF THE MANUFACTURER OF YOUR DEVICE TO CORRECT A "PILOT AGP," RECOMMENDS "AGP GART" OR "USB DRIVER" ISSUE; IT WILL NOT FIX YOUR PROBLEM.Please read the attached files before installing (Readme.txt and ReleaseNotes_9.4.0.1017.htm)
Key words: 82801, ICH, health child and maternal
-
installation of the HP scanning software
Hello
I have a Photosmart 5515 (a 5510 duplex I think!). I have run windows 8. Install the driver and I can use the printer as the printer - connected by USB cable. I can even scan a document in WORD using ALT I P S. But I can't get the system to install the HP scanning software. Whenever I try to install using the HP download (file PS5510_1315.exe name), he extracted the file and then asking you to identify the printer. He does not see the existing driver and it says to plug the printer into an available USB port. Its already plugged in of course. It will not allow me to go further. I tried (I think that (all combinations including the removal of all the softerae of hp on the computer, remove the printer from the Control Panel, unplug the printer and restarting the conmputer to get a 'clean' install.)) All to nothing does not. I tried every way. I tried the such HPPSDr as recommended by HP. When run, it recognizes the printer, talk to the printer, asks if I want to fix scanning and crosses two scans (the printer buzzes far happily) but then comes with the message window titled "HP TWAIN" "HP Photosmart 5510 series is not found." This is after she has had discussions with the thing! Within this program of doctor, you can ask to solve printing problems too. When I take this road all is supposed to be good.
What I am doing wrong - I know that IIT should be simple, but I can't. Thanks in advance. John
Hello
Try to run the HP printer below installation wizard by following the steps, don't forget to keep the USB connected before starting the tool:
If it persists, I would also try a different USB cable, directly connected to your PC and not via a hub or extention, a USB 2.0 and not a USB 3.0 cable and not longer than 2 metres long.
Shlomi
-
How do I know what software is causing the error to Windows Installer: lack of program
original title: How do I know what software is causing the error to Windows Installer
Windows XP
When you get this message that keeps popping up every two hours-
The upgrade patch cannot be installed by the Windows Installer service because the program to be upgraded
may be missing or the upgrade patch may update a different bersion of the program. Make sure that the program
to be upgraded exists on your computer and that you have the good patch upgrade. ."
How do find you the application or software, or the program is causing the problem. ?
It is a simple solution.
Go in run, type: msiexec /Unregister 'press the ok button.
Back to run, enter: msiexec/regserver "press ok.
Youre thru. Restart the pc
-
Hello
I keep getting error messages when I use the computer. It started two days after you download an update from Windows. A sample of the error is:
C:\windows\system32\difxapi32.dll is not designed to run on windows or it contains an error. Try to install the program by using the original installation media or contact your system administrator or the provider of software for support.
I use a vista. I don't know how to solve this problem, many want to help.
Thank you.
Hi Colinthebrave:
Start with this little tool to help get rid of the error, once your system is stable again and then try to run your updates again.
Thank you for your message; Let us know how it goes.
o
o The System Restore tool
If the problem you are experiencing started occurring recently, you can use the System Restore tool. Using this tool, you can restore the computer to an earlier point in time. The tool using System Restore may not necessarily help you determine the problem. When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.
To restore the operating system to an earlier point in time, follow these steps:
1. Click Start, type system restore in the search box, and then click System Restore in the list programs. If you are prompted for an administrator password or a confirmation, type your password or click on continue.
2. in the System Restore dialog box, click on choose another restore point and then click Next.
3. in the list of restore points, click a restore point created before you started having the problem, and then click Next.
4. click on finish.
The computer restarts and system files and settings are back to the State they were in when the restore point was created.
Don
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think. -
My computer will not allow the installation of the Adobe Air software, a message informs you that I must refer to the administrator, I'm the only user on this computer. Help please.
Thank you, Nicholas Cooper.
Here you go:
- Right click on the installer.
- Click on "Run as Administrator".
-
I have a new hp running windows 8.1 in turn and have tried to install the adobe reader software. The installer downloads (1) and I choose to run it, but it is just a blank screen appears. I checked the Task Manager and it takes memory, but does nothing. After you let it run for 3-4 minutes, I kill the task. What can I do to get the player installed on this machine? I tried using chrome, firefox, and explore and get the same results with everyone.
Try the Installer http://get.adobe.com/reader/enterprise/ offline
-
software installation problem left 3rd after the recovery procedure
I had the software installed on my laptop which worked well, but I had to run my laptop recovery disk,
I saved most of my stuff to a USB but when I try to install a special software I get message "this application is registered to John (me)", but when I click ok I get the message "the current key has been locked to another machine.Contact [email protected] for a new key.
Can anyone offer advice on how to fix this problem?
Best regards, John
It is based on the operation of your software.
What software is this?
Have you tried searching the site of software developers?
-
I'm trying to install the HP printing software, but the error message that the firewall must be enabled. However, I'm unable to turn on the firewall. The sytem keeps taking me in circels telling me I can '; t activate the firewall because the service is disabled.
Anyone have this experience? Suggestions to solve? Thank you!!
PS: I use VISTA w/SP2
Hello
How to turn on the firewall enabled or disabled in Vista Windows
http://www.Vistax64.com/tutorials/92697-Windows-Firewall-off.htmlCheck dependencies and their dependencies here:
http://www.blackviper.com/WinVista/services/Windows_Firewall.htm
For Services
Start - type in the search box-> find Services at top - right click - RUN AS ADMIN
(Means that you can right-click on the command prompt and RUN AS ADMIN).
---------------------------------------------------------
Some antivirus/security products may cause this error. McAfee, Norton, Windows Live OneCare.
ThreatFire are some. What antivirus/antispyware/security products you have on machine now. And
who have you ever on it, even if you have uninstalled them. (These leave the remains that can cause some)
strange questions.)Check the default services and dependencies to ensure that they are running.
http://www.blackviper.com/WinVista/services/Security_Center.htmSecurity Center not related anti-virus or firewall State correctlyhttp://www.winhelponline.com/blog/security-center-not-reporting-anti-virus-or-firewall-status-correctly/
How to fix Vista Reporting incorrect information Security Center
http://www.Vistax64.com/tutorials/195736-Security-Center-not-reporting-correct-information.htmlHow to disable or enable the Security Center in Vista
http://www.Vistax64.com/tutorials/67737-Security-Center.htmlThis thread might help as it might be a permissions problem.
http://social.answers.Microsoft.com/forums/en-us/vistawu/thread/3d2049ae-4581-439b-8E15-3f603f5c60f0/=====================================
Also check with HP support and forums.
HP support
http://welcome.HP.com/country/us/en/support.htmlContact HP
http://welcome.HP.com/country/us/en/contact_us.htmlHP forums
http://h30434.www3.HP.com/PSG/I hope this helps.
Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right. -
Extraction of fundamental characteristics - Watchdog Agent VI could not download the cRIO
Hello
I design an application in real time on one OR cRIO-9022, using the Watchdog Agent made by IMS Center toolkit.
During the loading of my VI on CompactRIO, I get the following error message:
Deployment SoundVib_Resampling.lvlib:oa_CIC Interpolation Interpolation Filter.vi Filter.viSoundVib_Resampling.lvlib:oa_CIC loaded with errors on the target and was closed.
LabVIEW: unable to load the shared library sndvib. *: OatCICInterpolatorByMovH:C. to ensure that the library is present on the target of RT. MAX allows you to install software from OR or FTP to transfer custom RT target libraries.I found that when I place the 'base Feature Extraction' VI within a 'disable diagram Structure', the deployment was successful, then the problem comes from this VI.
The error message tells me to install a library on the cRIO, but I don't know where to find it.
Thanks for you help,
David
Thanks Benedict,.
The 'noise and vibration' driver installation on the cRIO solves the problem
-
All,
I have a cRIO-9068 I try to use the scan mode for. I have intalled all the latest drivers and software as explained. However, when I put my chassis to scan mode, then select deployment all, I get this error on my chassis and all my modules:
"The current module settings require a NI Scan Engine support on the controller. You can use Measurement & Automation Explorer (MAX) to install a software package recommended NOR-Rio with NI Scan Engine support on the controller. If you installed LabVIEW FPGA, you can use this module with LabVIEW FPGA by adding an element of FPGA target under the chassis and drag and drop the module on the FPGA target element. »
Everyone knows this or know why labVIEW does not recognize that the software is installed on my cRIO or is it not installed correctly?
AGJ,
Thanks for the image. I saw a green arrown beside all my pictures of chip and it seemed that meant that the software wasn't really being installed. I formatted my cRIO and did a custom install. My problem was that I had the two labview 2013 and 2014 installed and the cRIO put conflicting versions of software. After doing a custom installation and choose only the versions of 2014, my picture now looks like yours!
Maybe you are looking for
-
I have a sidewinder force feedback pro for windows 98... When I upgraded I can't use it any more (it is 9 pins) so I need the windows xp software... How can I manage it works? Please help me
-
LRT224 redirection port internal port different external
Port forwarding seems to work flawlessly - but I need to route allows you to say external port 940 to internal port 1005. On most routers, you choose this in the "service" module or the module "port forward" - but I can't seem to find anything to ind
-
I'm trying to implement 2 screens (extended desktop mode) and when I connect them both, however, I got a picture on two screens, one of them is color purple/pink. I have swithced monitors around, it's NOT either of the monitors, they bot work very we
-
Original title: I installed gta san andreas copland in my pc, when I pressed the windows key or to open Task Manager gtasa automatically closes with the message 'gtasa' stopped workingI have installed gta san andreas copland in my pc, when I pressed
-
Computers not appearing is not on the network
I have 2 laptops and a desktop connected to my network computer home, all running windows 7. At one point, I was able to see them appear on the network and able to share files on the network. Recently, any changes made on any other computers that may