The device, \Device\Harddisk1\DR1, has a bad block.

Similar Questions

• "The device, \Device\Harddisk0\DR0, has a bad block" on Dell Vista SP2

  I am repeatedly getting the error "the device, \Device\Harddisk0\DR0, has a bad block." in the event viewer. Recently, I fixed a security problem that prevented me to install windows updates. For this, I ran CHKDSK (see results below), System File Checker, and a complete analysis of the system of McAfee, spybot and Malwarebytes, both in security and the good start. How can I check for errors on my HARD disk?

  --------------------------------------------
  My problem earlier wire: http://social.microsoft.com/Forums/is/genuinevista/thread/60c76236-abd2-4fea-8980-007f424a8eb0

  Although most things seem to work very well, "the device, \Device\Harddisk0\DR0, has a bad block." error still occurs in the event viewer despite the installation of updates/CHKDSK and SFC. Check the results of said disc 'the volume is clean' and the System File Checker showed no errors. Windows resource protection did not find any breach of integrity. Any ideas, what is happening?

  In addition, I don't know if this is related, but a problem with the wireless network connection keeps recurring. "Windows wireless service" is not automatically start during the boot. It must manually be diagnosed and started. He gave the following error message:

  

  In network connections, the IPv4 and IPv6 protocols are verified and most up-to-date driver software is installed. When I tried to update the drivers under devices, I got the following message. "The best driver for your device is already installed. Windows has determined that the driver for your device software is up-to-date.

  -----------------

  New report MGADiag after CHKDSK runs and the installation of the updates.

  Diagnostic report (1.9.0027.0):
  -----------------------------------------
  Validation of Windows data-->
  Validation status: genuine
  Validation code: 0
  Code of Validation caching online: 0x0
  Windows product key: *-* - F4GJK - KG77H-B9HD2
  The Windows Product Key hash: iJAth4TbScMi8HdcPurlASXdEkw =
  Windows product ID: 89578-OEM-7332157-00204
  Windows product ID type: 2
  Windows license Type: OEM SLP
  The Windows OS version: 6.0.6002.2.00010300.2.0.003
  ID: {A5A5B929-9AF8-43E5-A311-544A304C88A3} (3)
  Admin: Yes
  TestCab: 0x0
  LegitcheckControl ActiveX: N/a, hr = 0 x 80070002
  Signed by: n/a, hr = 0 x 80070002
  Product name: Windows Vista (TM) Home Premium
  Architecture: 0x00000000
  Build lab: 6002.vistasp2_gdr.110617 - 0336
  TTS error:
  Validation of diagnosis:
  Resolution state: n/a

  Given Vista WgaER-->
  ThreatID (s): n/a, hr = 0 x 80070002
  Version: 6.0.6002.16398

  Windows XP Notifications data-->
  Cached result: n/a, hr = 0 x 80070002
  File: No.
  Version: N/a, hr = 0 x 80070002
  WgaTray.exe signed by: n/a, hr = 0 x 80070002
  WgaLogon.dll signed by: n/a, hr = 0 x 80070002

  OGA Notifications data-->
  Cached result: n/a, hr = 0 x 80070002
  Version: 2.0.48.0
  OGAExec.exe signed by: Microsoft
  OGAAddin.dll signed by: Microsoft

  OGA data-->
  Office status: 114 blocked VLK 2
  Microsoft Office XP Professional with FrontPage - 114 VLK blocked 2
  OGA Version: Registered, 2.0.48.0
  Signed by: Microsoft
  Office Diagnostics: 025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3

  Data browser-->
  Proxy settings: N/A
  User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)
  Default browser: C:\Program Files\Mozilla Firefox\firefox.exe
  Download signed ActiveX controls: fast
  Download unsigned ActiveX controls: disabled
  Run ActiveX controls and plug-ins: allowed
  Initialize and script ActiveX controls not marked as safe: disabled
  Allow the Internet Explorer Webbrowser control scripts: disabled
  Active scripting: allowed
  Recognized ActiveX controls safe for scripting: allowed

  Analysis of file data-->

  Other data-->
  Office details: {A5A5B929-9AF8-43E5-A311-544A304C88A3}1.9.0027.06.0.6002.2.00010300.2.0.003x 32*-*-*-*-B9HD289578-OEM-7332157-002042S-1-5-21-3777094449-617660858-91839038Dell Inc.. MM061                           Dell Inc.. A14 20070402000000.000000 + 00056303507018400FE04090409Central Standard Time(GMT-06:00)03DELL M07 114114Microsoft Office XP Professional with FrontPage104iCnywwNW1w4s9ukTIwGMGxyGic =54185-640-0000025-1798914 39476F84C4B4004

  Content Spsys.log: 0 x 80070002

  License data-->
  The software licensing service version: 6.0.6002.18005
  Name: Windows Vista, HomePremium edition
  Description: operating system Windows - Vista, channel OEM_SLP
  Activation ID: bffdc375-bbd5-499d-8ef1-4f37b61c895f
  ID of the application: 55c92734-d682-4d71-983e-d6ec3f16059f
  Extended PID: 89578-00146-321-500204-02-1033-6000.0000-1402007
  Installation ID: 007894240565911961931104634943657564676410030663392174
  Processor certificate URL: http://go.microsoft.com/fwlink/?LinkID=43473
  The machine certificate URL: http://go.microsoft.com/fwlink/?LinkID=43474
  Use license URL: http://go.microsoft.com/fwlink/?LinkID=43476
  Product key certificate URL: http://go.microsoft.com/fwlink/?LinkID=43475
  Partial product key: B9HD2
  License status: licensed

  Windows Activation Technologies-->
  N/A

  --> HWID data
  Current HWID of Hash: OAAAAAEABQABAAEAAQABAAAAAwABAAEAJJRiENrxWFBy8jZ2jNDqTizZupDy9IwU5rIQVqxW9Eg =

  Activation 1.0 data OEM-->
  N/A

  Activation 2.0 data OEM-->
  BIOS valid for OA 2.0: Yes
  Windows marker version: 0 x 20000
  OEMID and OEMTableID consistent: Yes
  BIOS information:
  ACPI Table name OEMID value OEMTableID value
  APIC DELL M07
  FACP DELL M07
  HPET DELL M07
  STARTING DELL M07
  MCFG DELL M07
  M07 DELL SLIC
  SSDT PmRef CpuPm

  Hello

  You look at the statistics of SMART to see if the hard drive is a failure.
  http://mikemstech.blogspot.com/2011/12/how-to-detect-failing-hard-drive.html

  If he is not in default, you run chkdsk /f /r to ensure that bad sectors are marked. One way to do this forum works it offline.
  http://mikemstech.blogspot.com/2011/12/how-to-perform-offline-system-integrity.html

  If the disk is failed, you may need to save your data,

  http://mikemstech.blogspot.com/2011/12/how-to-rescue-files-from-damaged-system.html

• Guard judgment of Windows XP. Event Veiwer Watch: \Device\Harddisk0\D, has a bad block

  I have a Dell Dimension 2400 with Win XP PRO SP3. It keeps closing after half an hour to an hour. The event viewer shows the following error in the system log: \Device\Harddisk0\D, has a bad block

  Same thing happens in Safe Mode as well. I ran McAfee who reported no virus. I have auto-updated from Microsoft on and just installed the lates updates.

  Help, please. Thank you... Nam

  Speed stop?

  Unexpected/unpredictable and quick stops are generally caused by overheating or bad RAM modules.  This happens too fast to create an entry in the newspapers.  Try downloading / running the freeware 'CoreTemp'.  It will show you how hot your CPU is getting and how close to maximum temperature, it is.  If this is your problem, open your folder and check your fans to make sure they turn all.  Use a can of compressed air to remove dust, because it can act like a blanket and heat your components.

  To solve your problem of bad block, run "Chkdsk" with the 'repair' or ' / R ' option.  This should clean up your bad block problem.

  "How to perform the disk error checking in Windows XP"

  <>http://support.Microsoft.com/kb/315265 >

  HTH,

  JW

• 'System restore is not able to protect your computer'-'disc 2 device\deviceharddisk1\D, has a bad block.

  Original title: SYSTEM ERROR - error Code 0 x 70020, July 27, 2011

  I got an error Code 0 x 70020 and stopped and restarted the computer. but when I tried to use system restore, I get the message "system restore is not able to protect your computer". I am not a Curmudgeon, one got any ideas what the problem is and how I can get around it.

  I also watched the errors of advanced system information log which had a message dated April 24
  "Disc 2 device\deviceharddisk1\D, has a bad block.

  Not sure if this has any relevance?

  Hello

  · What is the service pack installed?

  · What is the number and the model of the computer?

  · Do you remember any changes made on the computer before the show?

  · You have security software installed?

  · You have a Windows XP Setup disk?

  Try the methods and check the results below:

  Method 1: Manually run the Chkdsk disk scanner. To do this, follow these steps:

  a. Click Start, click Run, type chkdsk /f /r and then click OK.

  b. at the command prompt, type Y to let the disc run when you restart the computer.

  c. restart the computer.

  d. Chkdsk runs.

  Method 2: Scan virus online and check if any malware or virus detected on the computer activity. You can run the scan for viruses online from the link below: http://www.microsoft.com/security/scanner/en-us/default.aspx

  NOTE: Make sure that you select the correct version of the operating system before downloading the scanner)

  You can also see: Troubleshooting for problems when you try to use the System Restore tool in Windows XP: http://support.microsoft.com/kb/302796

• The driver has detected an error of the controller on \Device\Harddisk1\DR1. What is the cause?

  I get this message on 7 11 windows event log IDs ' driver has detected an error in the controller on \Device\Harddisk1\DR1. "" The message keeps poping up when ever I insert my usb memory key but the DR number changes when I swap beetwhen and other memory usm drives exmp usb ports. "The driver has detected an error of the controller on \Device\Harddisk1\DR3." otherwise, my system is runnig perfect.

  Hello

  Check the drive for errors and see if it works fine it after.
  http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors
  The link above includes steps for the same.
   $C God will not look you over for medals, but for scars. Each winner has scars; I do this either on the same heart

• Starting problems, get the error "there is no disk in the drive. Please insert a disk into drive \Device\Harddisk1\DR1.

  1st problem: yesterday I started getting a popp window with the text following formulation - "there is no disk in the drive. Please insert a disk into drive \Device\Harddisk1\DR1' I have no idea what this introduced him or how stop it.  Any suggestions?

  2nd problem: whenever I restart my computer or shut it down and then power up the white bar that moves from left to right only moving to halfway through and then stops. I then have to hold the power button in until the computer turns off again and then rehit the power button. When it starts to power back up the white bar is always in the Middle, but then begins to finally complete the passage to the far right of the box. This problem started when I loaded the software for my printer Canon MX870 new that I bought and installed in October 2010 and has been done since then. I removed and reloaded the software of the printer on three different occasions but the problem persists.

  Hi frankb911,

  Please see the thread with a similar problem and fix possible:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-performance/there-is-no-disk-in-the-drive-please-insert-a-disk/b9a130b2-4261-4385-a51f-28005f209a1d

  I hope this helps!

• Error: "regsvr.exe - no disk there is no disk in the drive." Insert a disk into drive\Device\Harddisk1\DR1 "_".

  Original title: regsvr.exe - disc no.

  Hello

  I get an error message whenever I insert my pen drive or memory card in my laptop. The error message is "regsvr.exe - no disk there is no disk in the drive." Insert a disk in the drive\Device\Harddisk1\DR1. There are only three options - Cancel, Try Again and continue. None of them works. I have to manually stop the system to get rid of it. Please help me get rid of this error message for always. Your response to this regard will be highly appreciated. Cordially Sashwat

  Hello, Sashwat

  If possible, test the drive in another computer and check if you are able to access or not. If this is not the case, the drive may be bad.

  If it's a USB card with an SD card reader, rather than a dedicated, flash drive check if the card is recognized and accessible in other drives/devices. Also, check the metal contacts on the card to make sure that nothing is blocking the metal contacts. If the card cannot be read in other devices and contacts are clean, the card is likely bad.
  If other devices can access the drive, but not by the card reader, the card reader could be bad.

  David
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• event ID #51, an error was detected on device \Device\Harddisk1\DR1 during a paging operation. ; Session "ReadyBoot" stopped because of the following error: 0xC0000188

  2 weeks ago I started to do, the driver has detected an error on \Device\Ide\IdePort0 controller, an error was detected on device \Device\Harddisk1\DR1 during a paging operation. ; Session "ReadyBoot" stopped because of the following error: 0xC000018. Event ID #51, #11 bottom line I check the disc, I restarted computer sometimes the logical disks and primary transmission is up to leave after a certain time.  About 6 months ago I bought a new car because I had the same problem.  I had checked, adjustment, cables, power, bios, software update settings, BIOS and decided he could be the player.  I used manufacturing software troubleshooting - the drive past all the test.  I used the S.M.A.R.T. test - it past.  As I said I check disk found nothing.  However, I deleted and brought another drive.  Now, I get the same indications listed above.

  Hi Robert,.

  I'm glad that you posted the request in the Microsoft community. If I understand correctly, you get an error message indicating boost loan session interrupted because of an error.

  Here is an article that talks about the error you are getting. Go through it and check.

  Here is an article on Ready Boost. Have a look at.

  Hope this helps and let us know if you need more assistance. We will be happy to help you.

• How to remove the error message there is no disc the disc in the Drive\Device\Harddisk1\DR1

  There is an error message which keeps popping up and I push to cancel several times before it will go away however he comes back to the top on my screen at random times. Meesage hpqtra08.exe - no disc, then below it reads "he not there no disc insert disc in the Drive\Device\Harddisk1\DR1.
  Please help me to remove it from my computer!

  Hello lala80,

  Thank you for using Microsoft Vista answers Forum!

  hpqtra08.exe is normally installed as part of the HP all-in-one printer, scanner, driver copy and install the software. It is a non-essential process, and it is at the discretion of the user, whether to disable. If disabled buttons as scan in the 'all-in-one' continues to work. However if you never use it it is safe to disable. It does not work, just the button scan in the multi functional.

  You can disable this feature by using msconfig in Windows.

  Click Start and type msconfig in the search box and press enter

  Click the Start (top row)

  In the list of programs, uncheck hpqtra08.exe

  If please reply and let us know if your problem is resolved or if you need more help

  David O
  Microsoft Answers Support Engineer
  Visit our and tell us what you think.

• SE error message: there is no disc in the drive. Insert a disk in drive \Device\Harddisk1\DR1

  Original title: CMD. EXE - NO DISK

  I use Windows Vista Home Premium 64

  I get a pop box which reads:

  cmd.exe - disc no.

  There is no disk in the drive. Insert a disk in drive \Device\Harddisk1\DR1

  It appears each time I try and do anything. It gives me 3 options "Cancel, try again, continue»

  If you click over there enough he goes, then pop up when you try to do something else.

  I tried to run Norton (without success), Spyware remover tools (Adware - without success)

  Any help would be appreciated.

  Hi angelover08,

  1. have you tried to change the drive letters of removable disks?

  If this isn't the case, you can try to change the drive letter designated to removable drives all the other letters other than E, F, G and check if it helps.

  Check out the link:

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-add-or-remove-a-drive-letter

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Description: the device, \Device\CdRom0, has a bad block.

  I have McAvee.  A month ago a Trojan plopped o program my screen that said it was Windows and set the virus if I would be a click.  I knew better than to restart...  It ruins your computer of my husband 5 years ago.

  I saw that once again, but since I had a lot of problems.  The INVESTIGATION period didn't recognize me.

  I now have a PC Health Check, which appeared and he had my name on it IP.  Now I see it's been blocked.

  First of all, I couldn't start up right.  I had to choose F1 or F2.  I fixed.

  Online has been a problem.  I think I have two or three different names.

  All my backups do not appear so I can reinstall to an earlier time.  I can not restore from disk.

  Now it says I have a bad block and it is something on my CD.   Description: the device, \Device\CdRom0, has a bad block.

  Hello

  Scan of Malware in Safe Mode with network.

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap the F8 key repeatedly until you are presented with the Boot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  Once in Safe Mode with network, download and run RKill.

  RKill does NOT remove the malware; It stops the Malware process that gives you a chance to remove it with your security programs.

  http://www.bleepingcomputer.com/download/rkill/

  Then, download, install, update and scan your system with the free version of Malwarebytes AntiMalware in Mode safe mode with networking:

  http://www.Malwarebytes.org/products/malwarebytes_free

  See you soon.

• Cannot start, had to use safe mode. Event Viewer, event system properties, error "the device / Device / Harddisk:O / D, has a bad block.

  I use my desktop computer to post my question, my laptop has the error.  First, he appeared on the journal 09/12/2010.  Said event properties' Source: disc, it gives the date and time, category: no, Type: error event ID: 7, critics: n/a, computer: laptop, Description: device/Device / Harddisk:O, / D, has a bad block for more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp

  It has not helped me, does anyone have any suggestions?

  This means that the player has / is a failure and should be replaced.

  Your laptop may have preinstalled utilities test which can be consulted before starting, manufacturers mobile site would give information

• No disc in the drive - no. disc, 'there is no disk in the drive. Insert a disk in drive \Device\Harddisk1\DR1

  Hello

  I use windows 7. When I try to connect the usb modem or remove drive in my computer, and then sometimes it displays a .exe - no disk popup, "there no disc in the drive. Insert a disc into drive \Device\Harddisk1\DR1. There are 3 options Cancle, retry, continue. But these options never work. It appers again. (I can't repair/restore my pc because I have only One Drive (C). so please help me...)

  Hi Kalyan,

  Thanks for posting in the Microsoft Community. Help us with more information:

  1. This problem is specific to these devices?

  2. Have you tried to connect the devices on different USB port?

  This problem can be caused by damaged USB drivers. I suggest trying the steps and check if it helps to fix this problem.

   

  Remove and reinstall all USB controllers

  To remove and reinstall all USB controllers, follow these steps:

  1. Click Start, click run, type sysdm.cpl in the Open box, and then click OK.

  2. Click the hardware tab.

  3. Click the Device Manager button.

  4. Expand Bus USB controllers.

  5. Right-click every device under the Bus USB controllers node and then click Uninstall to remove them one at a time.

  6. Restart the computer to reinstall the USB controllers automatically.

  7. Plug in the removable USB storage device and test to make sure that the problem is solved.

  Let us know the status of the issue. If you need help, please after return. We will be happy to help you.

• \Device\HardDisk0 has a bad block

  I am receving since past two days the same message.

  \Device\HardDisk0 has a bad block
  When I click details it shows the name of the next file.
  IoLogMsg.dll
  My operating system is: Windows Server 2003
  Can you help me?

  MF

  Server questions should be asked on the Technet site

  http://social.technet.Microsoft.com/forums/en-us/home

• Backup associated with repeated warnings ID 51: an error was detected on device \Device\Harddisk1\DR1 during a paging operation (or \Device\Harddisk5\DR5)

  I just found out about 7 000 event ID 51 warnings in the event viewer.

  These warnings began when I started using an IEEE 1394 external drive for backup. I can't say if the more than 7,000 warning messages started after formatting, or when the backup began.

  About 5,000 messages occurred during the first backup which lasted several hours, back on February 24.

  All of them had: an error was detected on device \Device\Harddisk5\DR5 during a paging operation.

  Managed backup done this night here and as far as I know. (I don't look in the observer of events at this time.)

  The next day, at 11:00, the messages have started, but this time in bunches of a dozen or less within one or two seconds. And they all change to this:

  An error was detected on device \Device\Harddisk1\DR1 during a paging operation.

  Since then, the warnings occur sporadically. The backup program ran on 28 February, and produces over a thousand more. A group that's happened when I tried to back up the registry to a subdirectory on the drive yesterday.

  What is strange, is that the drive seems pretty much OK. Backup completed without error. I can copy files to it, and then copy it.

  Given that these are warnings, is this correct? A driver problem?

  the drive is using 6.1.7600.16385 (win7_rtm.090713 - 1255)

  I formatted just before using it for the backup. These are the old years, but we never had any problems with it before.

  Any ideas on how to understand what is happening?

  You can also try changing the driver firewire to INHERIT one. (Device Manager, Bus IEEE 1394 controller, software update driver, browse my computer, let me pick from a list... Choose the line of inheritance in it.