The driver \Driver\AFAmgt failed to load for the device USBSTOR

Similar Questions

• The \Driver\WUDFRd failed to load the device driver USB\VID_0483 & PID_2016\5 & 295bd535 & 0 & 2.

  WUDFRd failed to load of the device

  Hello

  I did a clean install of Windows 7 64 bit and everything goes fine until I started to add the specific drivers of lenovo t61p.  I get the following in the Event Viewer error message:

  The \Driver\WUDFRd failed to load the device driver USB\VID_0483 & PID_2016\5 & 295bd535 & 0 & 2.

  After a lot of Googling, I found that the usb device is a fingerprint reader.  remove the fingerprint reader drivers removes the error in Event Viewer.

  AuthenTec TouchChip fingerprint coprocessor uses the v1.5.0.289 driver.  their website States that the error is a problem with Microsoft.  See this link:

  http://support.AuthenTec.com/Knowledgebase/KBview/tabid/843/ArticleID/443/WUDFRd-failed-to-load-for-the-Device.aspx, or search their Knowledge Base for "WUDFRd failed to load for the device.

  I see that the other members of the forum answers have similar problems, but they still have to find a solution.  is that someone in Microsoft could provide an update for a fix?

  Yes! After two years, I found a solution.  I installed a previous version of Lenovo sw fp and it fixes attention on win 7 sp1 2 t60.  I've been running for about 3 weeks and warning went on two PCs. then, download and install IN1FGP08WW1.exe.  It is fp s-o of Lenovo in UTEK and there the pilot to clear the warning.  BUT it's not as safe as the current Lenovo sw fp.  Apparently, she was abandoned when authentic bought UTEK because of this.  as I understand it, if someone has physical access to your pc they can decifer pw of windows in the registry.  This isn't a big problem for me.

• ERROR 7026: CONTINUATION OF THE DRIVER (S) FAILED TO LOAD AFTER RESTART

  The event viewer showed this error after startup for 2 or 3 days. The drivers listed are OMCI and NULL. I've been ignoring it causes web search seems to show OMCI is a cost of control tool for IT managers that has to do with the networks... I have only one computer.  My system performance is very good. I went to devices and updated all the drivers. Should I worry about this? I had to do cleans up registry, disk defragmentation, disc chk, associated clean disc trying to get rid of a virus... This error code showed some time ago and then stopped and now there back THANKS Pharmerbill

  Hello

  This issue may be caused if one of the device driver on your computer is faulty. This is probably due to the graphics card. You should try to reinstall the drivers adpter display in most of the cases it fixed the issue.

  See you soon.

• Driver Installation Failed: Could not find media device for this driver

  I have a HP with Windows Vista (32 bit) dv6646us and have had a problem with the audio device. The sound works sometimes, but above all the system does not even recognize the audio output device (in this case, I see the speaker icon in the taskbar with a cross mark). Another model is that the laptop does not recognize the audio device, but no sound is produced (in this case, the "speaker" icon doesn't have the cross mark). When the system has at least recognize the audio device, I can solve the problem by using the Microsoft Fix it 50131. However, when the system does not recognize the audio device, nothing seems to work. When I go into Device Manager, there is no sound, not just a pilot section. The laptop is supposed to use Conexant High-Definition Audio Driver, but when I try to install it, I get the following message: failure of the driver Installation: Media not found device for this driver.

  In another forum, someone has solved the same problem in a system with the 32-bit version of XP by downgrading his memory from 4 GB to 2 GB, based on his knowledge that a 32-bit system cannot take 4 GB of RAM (it has started having the problem after that first, he upgraded the RAM from 2 GB to 4 GB). However, I don't know if the same applies to my problem because the sound system sometimes works with the current system with 4 GB of RAM and also my laptop is supposed to hold up to 4 GB of RAM (and he does not the 4 GB of RAM). So, I was wondering if there is another possibility for a cause and a solution to this problem.

  Hello

  ·         If it works well before? If so, remember to do recent changes on the computer before this problem?

  ·         Do you think the audio device when there is no X on the volume icon?

  I suggest you follow the steps mentioned below:

  Method 1:

  You can follow this section "By my speakers is crackled or distorted" in the link below:

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

  Method 2:

  If the previous step fails, uninstall and reinstall the audio drivers completely, follow the steps below:

  a. click Start, type Device Manager in the Start Search box and press ENTER.

  b. click continue. The Device Manager dialog box appears.

  c. If you are prompted for an administrator password or a confirmation, type the password, or click continue.

  d. in r management device, right click on audio and its driver and click on uninstall.

  e. install the last driver audio drivers on the manufacturer's Web site.

  Method 3:

  If the previous step fails, follow the steps described in the following link:

  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows

• X 1 carbon Gen4 SCCM package for Win10 x 64-Driver Ethernet fails to load on WIM image

  Hello world

  Im trying to deploy Win10 64-bit for the new X 1 carbon Gen 4 (type 20FB). IM using the following SCCM Package (http://support.lenovo.com/ch/de/downloads/ds111758) about the drivers.

  The problem I have is, after loading the WIM image from our WDS server, it stops deployment with the following error message: the following network device had not installed a PCI VEN_8086 & DEV_1570 & SUBSYS_223317AA & REV_21 driver

  The fact is that the SCCM package I mentioned, has exactly this driver in it... and the new X 1 Yoga uses the same package and its working properly.

  If anyone has an idea what may be wrong, please report it as soon as possible.

  If you need more information, contact me.

  Thanks for help

  Best regards

  MS

  SRY, slipped just with the 20.19.15.4416 update

• AD60D7P4 IDE Controller no driver loaded for this device

  I recently had some performance issues with computer ym so I went into Device Manager to update the drivers and such and this AD60D7P4 IDE controller has a yellow exclamation mark next to it. So I clik to update the driver I did this multiple times yet no driver found for him. Also, I downloaded several programs for the update of autopilot just to make me pay for them after pretending to be free. Can someone please help me with this, I think that maybe that's the problem Im having but I cannot fix.

  Hi JHarrison,

  What is your computer brand and model?

  I suggest updating the drivers from the chipset of your PC by downloading the latest version from the manufacturers Web site.

  Chris
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows Update driver Fresco Logic USB Hub rot caused the pilot to read device status: the drivers for this device are not installed. (Code 28).

  Windows Update driver Fresco Logic USB Hub rot caused the pilot to read device status: the drivers for this device are not installed. (Code 28). The Roll Back button is not active. Where can I get the previous driver that came with my system. ASUS N53S Windows 7. Thank you very much.

  Hello

  Thanks for posting in the Microsoft Community.

  I understand your annoyance that you cannot update the driver hub USB rot. Please follow the steps below to help you to solve the problem.

  I would like to inform you that a Code 28 error is caused by a driver missing for that piece of hardware.

  There are all sorts of reasons that a driver could not be installed for a device, but your troubleshooting the problem will be the same regardless of the root cause.

  • Remove or reconfigure newly installed unit.
  • Restore the version before your driver update.
  • Use system restore to undo recent changes in Device Manager.

  Step 1: Roll back the driver to the version before your update.

  If you are having problems with your computer or device after upgrading sound driver, you can restore to an earlier device driver. If you are having problems with your computer or device after upgrading sound driver, you can restore to an earlier device driver. If you are having problems with your computer or device after upgrading sound driver, you can restore to an earlier device driver. If you are having problems with your computer or device after upgrading sound driver, you can restore to an earlier device driver. Check out the link below to make back the driver:

  http://Windows.Microsoft.com/en-in/Windows/restore-driver-previous-version#1TC=Windows-7

  When Windows 7 starts up again, it will load with the device driver of this material that you had previously installed.

  I suggest you to uninstall the driver from hub to rot Fresco Logic USB Device Manager and install the most recent on the manufacturer's Web site.

  Tips for solving common driver problems:

  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-driver-problems

   

   

  Hope this information is useful. Feel free to get back to us for further questions or problems related to the Windows operating system.

  Thank you.

• When you restart the XP machine, get the error 'search for floppy drive has failed.

  When I restart I always get:
  "Search for floppy drive has failed.
  Press F1 to continue, F2 to run the configuration utility.
  When I have strike F1 Windows loads but how do I get around this?
  I am running Windows XP. I don't know what other information you need.

  * original title - startup problem.*

  Hello

  The BIOS is configured to boot from a floppy disk to 1.

  / Settings (BIOS/CMOS) often F2 so watch the screen you start for the key - set the
  First start stopped on the hard drive.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• The TOSHIBA for Bluetooth ACPI driver update failed

  Hi all

  I have a P870 running on Windows 7 & until recently BT worked fine, now it doesn't.

  When I tried to download the latest version of the driver it says that I have the latest version of the driver.
  He also says that the device is functioning properly.

  It does not recognize my S4 where before he did.
  I now can not get it to pair because he does not see.

  When I did the last update of MS that I noticed the results put BT update failed, as shown below.

  Any ideas on a fix would be appreciated.

  The TOSHIBA for Bluetooth ACPI driver update
  Installation date: 08/08/2015-09:37
  Installation status: failed
  Error details: Code 80246005
  Update type: recommended

  This driver has been provided by TOSHIBA for the support of Bluetooth ACPI

  More information:
  http://sysdev.Microsoft.com/support/default.aspx

  Help and Support:
  http://support.Microsoft.com/select/?target=hub

  BT is activated using the function keys?

  What is the status of the Bluetooth technology in Device Manager?
  You see errors, some yellow exclamation?

  What you can do is use provided by the windows system restore and backup option and return to the point of time at the beginning, before the update have been installed...
  No doubt this has problem of BT

• Could not load the device driver for DVD/CD-RW - Satellite 1110

  I have a Satellite 1110 and something has gone wrong with my DVD/CDRW and it will not read any CD. It is reported as a CARPET * A UJDA730 DVD/CDRW but the device status is shown as:

  "Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) »

  I tried to uninstall and reinstall the device, but the error just return. I can't find a driver to make it on the web site of the manufacturer or Toshiba. I don't want to use the product recovery CD because it means I'm losing all software and data on the hard drive.

  Can someone advise how to recover from this situation?

  Thank you

  Hello

  First of all you n t a driver for the CD/DVD drive. The drive uses the standard Windows OS driver and it s not necessary to install additional.
  I suppose that there could be something wrong with the registry entry.

  Please check this forum announcement:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=13843

  The user has used the statement that has been proposed on the site of Microsoft.
  This should help.

  Please post again if this method is successful.

• Audio loss. UAA Bus Driver reads Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39). All the patches?

  Audio loss.  Device Manager indicates Microsoft UAA Bus Driver as: "Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) ».  Tried to update driver and restore without success.  Tried the program of "Fix - It", which has identified an error with the sound system, but said that he could not fix it.  Restored to an earlier date but still what system did not go.  Tried to uninstall and reinstall the driver.  Uninstall was successful but reinstall it read that the hdaubus file does not exist.  I'm a computer dunce.  Any help out there?

  Hi BarbaraWolfe,
   

  There are many causes of Code 39 errors:

  • A required device driver is missing.
  • A required binary file is corrupted.
  • There is a problem with the file I/O process.
  • A driver that refers to an entry point in another binary file cannot load.
  Re-install the driver by downloading it from the link given:
   
  Universal Audio Architecture (UAA) High Definition Audio class driver version 1. 0a available for Windows XP, Windows Server 2003, and Windows 2000
  Additional reference on:

  Explanation of error codes generated by Device Manager in Windows XP Professional

  Check if that helps.

• I have a Toshiba Satellite A105-S361 and I get this message: Windows successfully loaded the device driver for this hardware, but does not the hardware device. (Code 41)

  I have a Toshiba Satellite A105-S361 and I get this message: Windows successfully loaded the device driver for this hardware, but does not the hardware device. (Code 41)

  Hello

  I suggest to refer to this link, scroll down to error code 41 and follow the steps and check if that helps:

  http://support.Microsoft.com/kb/310123

  It will be useful.

• Add/Remove components error and DVD driver error: Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)

  Original title: Add/Remove components error and DVD driver error

  Yesterday, I removed several components of windows to attempt to clean my cpu. After the reboot, I noticed that my DVD drive disappeared. I tried to update the driver but told me I have the most updated version, I uninstalled and reinstalled the drive, but I still get the same error. Under Driver Details, it shows that I have a lot of drivers for my Phillips DVD player. However, the status of the device is the following: Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) Click Troubleshoot to start the troubleshooter for this device. I've done the troubleshooting, and the two options has not fixed the problem.

  Then I tried to add windows components that I removed, thinking maybe that was the problem. However, when I try to add them, I get an error message that says: 'Setup cannot copy the file zClientm.ex_' it shows the location of this file as being in windows/i386, and of course, the file is located in this folder. So when I go to browse to locate the file, I find and click on it to open it, but I keep getting the same error message that the file is not found and Setup cannot continue.

  I realize that this problem seems very rare and weird, but any help at all would be appreciated. Thank you.

  Hello
   
   
  Code 39: Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)

  Explanation of error codes generated by the Device Manager in Windows XP Professional http://support.Microsoft.com/kb/310123

   

   

  Method 1.
  Microsoft Automated Troubleshooting Services scans your computer and detects that the root causes of common problems, then automatically solves the problems that he finds and offers additional resources if the problem is not resolved. Click run now in the article below.

  Your CD or DVD drive cannot read or write media
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

   

   

  Method 2.
  Also, try the methods listed in the section below and check.
  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

   

   

  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Windows cannot load the device driver for this hardware (HL-DT-ST DVDRAM GH40F SCSI CdRom Device) because the driver may be corrupted or missing. (Code 39)

  Original title: the answer useful?

  Help, please! Windows cannot load the device driver for this hardware (HL-DT-ST DVDRAM GH40F SCSI CdRom Device) because the driver may be corrupted or missing. (Code 39)

  Hello

  Code 39 means that the driver is corrupted or missing.

  Please make all below even if you have done some before as it is often the set of operations which solves
  the question.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  --------------------------------------------------------------

  Also check with your system manufacturer to see if there are any updated drivers for your DVD. Or even if it
  are you can reinstall the 'old'. Many use Windows default drivers however some special aura
  ones. Also check the website of the manufacturer of the car.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• (KEYBOARD ERROR) Windows cannot load the driver for this hardware device because a previous instance of the device driver is still in memory. (Code 38)

  (KEYBOARD ERROR)

  Windows cannot load the driver for this hardware device because a previous instance of the device driver is still in memory. (Code 38)

  Hello

  I don't know how it happened.

  I tried unistalling the software but have the same problem when connected to e

  Help, please

  Hi Davedirect,

  ·        It's a wired keyboard or a wireless keyboard?

  ·        Who is the manufacturer of keyboard?

  ·        Since when are you facing this problem?

  ·        You did changes to the computer before this problem started?

  ·        Have you tried to restart the computer and check if the keyboard works normally?

  However, you can try to uninstall all the previous and software drivers installed for the keyboard by following the steps below.  More later, restart the computer and install the latest drivers and software and check if that helps you solve the problem.

  Step 1

  Remove the drivers from the computer. To remove the drivers to follow the steps below:

  a. Click Start and enter the type of search box of start of the press and "appwiz.cpl".

  b. in the programs and features window select the keyboard software installed on the computer and uninstall the drivers.

  Step 2

  During the uninstallation, the device in the Device Manager, make sure that you follow the steps below:

  a. Click Start.

  b. access control panel > system > hardware > Device Manager.

  c. open Device Manager and expand the keyboard device.

  d. right-click on the device keyboard and uninstall the device.

  During the uninstallation of the device in Device Manager, make sure that you place a tick against 'delete the driver for this device '.

  Step 3

  Also, you can try to update the drivers for your keyboard from the Device Manager and check if it helps. Access the link below and follow the steps to update the drivers.

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Access the link below to learn more about the error code 38:

  http://support.Microsoft.com/kb/310123

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.