The easiest way to support the call between the ports of SPA-8000 and 2 GWs?

Similar Questions

• Comparing the Portégé R500-10J and R500 - 11 c

  Hello

  Anyone know the difference between Portege R500-10J and Portégé R500 - 11 c?

  Hello

  I searched and studied a bit more on different websites, and it seems that both computers portable Portege R500 support the same hardware specifications:
  Intel Core 2 Duo 1.2GHz / 2048 MB / 160 GB / TFT12.1 / Intel GMA 950 GPU

  I think these two laptops are delivered and designed for different countries and the model number is therefore different.

  The Portégé R500-10J PPR50E-00K00PSP seems to be sent to Spain, and the Portege R500 - 11 c PPR50E-00K04LRU can be purchased in Russia.

  Best regards

• Linksys WRT1900ACS shows all the ports that are open and firmware restore.

  Hi bought a new Linksys WRT1900ACS and has the following questions.

  a. How can I determine whether version hardware version 1 og 2.

  b. making a portscanning on the Linksys WRT1900ACS for the internet I found that several ports where free.

  When I went into the Setup, I get only portforwarded 20/21.

  I could access my internet QNAPS 3 + more.

  But the router WRT1900ACS didn t show this when it has been planned, why?

  I now that the QNAP may change the port settings, but I do not have "done this or asked for it", but why it does not appear

  When I log in the WRT1900ACS via Smart Wi - Fi.

  (can not see all 3 QNAPS when I use my linksys EA6500 router.)

  c. After you have determined the B. I tried to Flash the firmware with the firmware OPENWRT. But now I can access the WRT1900ACS and the WiFi is not charged more. The normal router works. How do I get:

  D: flash the original firmaware (via lan)

  e: what OPENWRT firmware has GUI and can be recommended for WRT1900ACS and where to download?

  f. are there links to og to youtube which is very imnformative to do this?

  Thank you

  John

  [email protected] wrote:

  Hi bought a new Linksys WRT1900ACS and has the following questions.

  a. How can I determine whether version hardware version 1 og 2.

  Thank you

  John

  This must appear on the label of the product below.

• On the issue of the port already in use and multiply the application instance?

  I use the message connection to receive sms. When I restart the application, I found the already used port exception. I've been through many posts and believe that BB allows a UNIQUE APPLICATION connecting the port of sms at a time. But the port of sms I know certainly is used only by my candidacy, is somehow wrong to create a second instance of application trying to access this port?

  This question confused me a lot of time, to appreciate someone give me a help.

  This problem has been resolved.

  The two possible solutions for this problem:

  1 re - save the connection string for registery push in the start method. but avoid registering a new when enforcement is woken up by sms push, otherwise it won't get the message.

  public void startApp()
  {
   String[] list = PushRegistry.listConnections( true );
              boolean isByPush = (list != null && list.length > 0) ? true : false;
              if(!isByPush)
              {
                  PushRegistry.unregisterConnection( connString );
                  PushRegistry.registerConnection( connString,Test.class.getName(), "*" );
              }
  
              bbReceiveSmsThread = new BBReceivingSmsThread(connString);
              bbReceiveSmsThread.start();        
  
  }
  
      private static class BBReceivingSmsThread extends Thread
      {
          private boolean stop = false;
          private MessageConnection mc;
          private String connString;
  
          public BBReceivingSmsThread(String connString)
          {
              this.connString = connString;
          }
  
          public synchronized void stop() throws IOException
          {
              stop = true;
              mc.close(); // Close the connection so the thread returns.
          } 
  
          public void run()
          {
              try
              {
                  mc = (MessageConnection)Connector.open(connString);
                  for(;;)
                  {
                      if ( stop ) return;
  
                      Message message = mc.receive();
  
                      String text = null;
  
                      if( message instanceof TextMessage ) text = ( (TextMessage)message ).getPayloadText();
                      if( message instanceof BinaryMessage ) text = new String( ( (BinaryMessage)message ).getPayloadData(), "UTF-8" );
  
                      if(text != null)
                      {
                         //do your message here
                      }
                 }
            }
            catch (Exception e) {}
          }
      }
  

• No link between IOM port 2/2/3 and fabric B interconnection

  Hello

  I am removing an uplink of the IOM to the fabric of interconnection in accordance with its not.  I tried to reset the module e/s and re - emphasize the chassis with no luck, it is still displayed in the GUI with the error message as in the subject.  We are running 2.0(1s).  The kit is not yet in production.

  Thanks for any help

  Hi barry,.

  The only way for you to clean up which will be de-Commission of the chassis in question and add it back again.

  Thank you!

  . / Afonso

• No link between the IOM, 1/1/3 and has 1/3 FI

  Hello

  When we first set up our UCS we connected all four of the IOM fabric interconnect Ports but now we wanted to remove both of them in order to save some ports on the FI. We configured the ports of #3 and #4 on the two FIs server and subsequently removed the cables.

  However, now that we receive the F0367 error message "no connection between IOM port 1/2/3 and fabric interconnect B:1 / 3" for all fabric ports where we have removed the cables.

  Same definition of chassis discovery 2 links and re-recognition strategy has not solved the errors.

  Does anyone knows how to fix this?

  Concerning

  Hello Lorenz,

  Are what version of the UCS you currently?

  Also see loss of traffic on the blades for which these flaws are high?

  I guess you hit the following bug: CSCtg74026 (compensation of IOM defects: not after change of political discovery chassis)

  This has been fixed in the current relase of 1.4. However, the solution is to make a chassis of comission and the re-discovery.

  I hope this helps!

  . / Afonso

• My audio is on the Audio Digital (S/PDIF), and I have NO SOUND.

  The problem is started when installing windows 7 on my desktop, or when installing a new audio or video card I'm not positive exactly when it started to happen. But all of a sudden the audio device only I got was Audio Digital (S/PDIF), which in fact did nothing.

  I figured out how to get the speakers on my monitor to work, I plugged the speaker cable into the port 'in line', blue and stakeholders have worked.  The cord is green light... the port is blue... it doesn't look right, it seems that it should be in the green port right? But it does not work like that.

  Anyway if I plug the monitor or headphones on in blue 'line' port it affects my speakers 'Speakers' "high definition Audio Device".  And I have audio.

  But I need to have a microphone that works as well for a class I have. But when I plug the headphones that it doesn't work, it doesn't recognize the microphone or even acknowledge that I plugged anything.  The helmet part works by plugging in 'line' port, but the microphone does not work.  He said that the recording device is set to Audio Digital (S/PDIF) and nothing else is listed in Device Manager.

  I have seen this problem posted elsewhere and I followed a lot of steps, I tried to download drivers realtek, windows update, update drivers for my Nvidia graphics card, and I even download Everest to be sure of my Audio device. It's what came SigmaTel STAC9220 A1 @ Intel 82801 GB ICH7 - High Definition Audio Controller [a-1].  The link to update the drivers was useless, but I looked online and found one on the site of Dell, he said it was for Sigma Tel STAC92XX... which should include mine.  I downloaded it, rebooted, and all of a sudden I got no. AUDIO DEVICE AT ALL.  Windows said I had no sound, and he tried to install the drivers, although I'm sure that I had done that we found my Sigma Tel Audio Controller.  Windows cannot install the, then suddenly he tried again and said it was successful.  But I'm right back where I started, still consider the Audio Digital (S/PDIF) is my recorder, speakers do not work unless it is plugged into the blue port in 'line '.   Nothing has changed...

  If anyone can help please let me know. I appreciate it.

  It happened to me, I just unplug and reconnect the plug and she is back to normal

• How to change the Port WSX

  I should have said that I am under WS 9.0.2 (production) here.  So I do not know where to post

  My host is Fedora 19.  When I try to go to the localhost:8888 reports of Firefox "unable to connect".

  The output of netstat - ttlnp is:

  TCP 0 0 0.0.0.0:111 0.0.0.0: * LISTEN.
  TCP 0 0 127.0.0.1:8307 0.0.0.0: * LISTEN.
  TCP 0 0 192.168.122.1:53 0.0.0.0: * LISTEN.
  TCP 0 0 0.0.0.0:22 0.0.0.0: * LISTEN.
  TCP 0 0 127.0.0.1:631 0.0.0.0: * LISTEN.
  TCP 0 0 127.0.0.1:25 0.0.0.0: * LISTEN.
  TCP 0 0 0.0.0.0:443 0.0.0.0: * LISTEN.
  TCP 0 0 0.0.0.0:17500 0.0.0.0: * LISTEN 2852/dropbox
  TCP 0 0 0.0.0.0:902 0.0.0.0: * LISTEN.
  tcp6       0      0 :::111                  :::*                    LISTEN      -
  tcp6 0 0: 1:8307: * LISTENING.
  tcp6       0      0 :::22                   :::*                    LISTEN      -
  tcp6       0      0 ::1:631                 :::*                    LISTEN      -
  tcp6 0 0: 443

  Go to localhost:631 brings up the page of CUPS online.

  Maybe if I changed WSX in listening on port 8307 I might have better luck.

  But just run sudo/usr/bin/vmware-install vmware-wsx u

  and then reinstall thke bundle does not give the possibility to specify the port - I got the first time I ran the bundle.

  In which directory is the spec WSX port number and I can change it?

  -----------------------------------------------------------------------------

  This was solved by uninstalling WSX 1.02 (dereconfiguring I should say) and then installing the beta version 1.1 (allowing NoScript OK access to localhost).  Always the possibility to change change the port was not found, but 8888 worked if the thread is unanswered. .  I would like to move this thread to the WSX forum but it's fairly inactive last I checked.

  WSX login screen looks better, but it will take me a while to go through the changelog.

  Hey Buddy,

  Could you please try to modify the configuration file under/etc/vmware/wsx?

  I update the port 8888 to 8901 and restart the service. Then I can access through http://localhost:8901 wsx.

  I tried on Fedora 18 x 32.

  I hope this can help.

• Limit the number of calls between areas of VCS/subareas?

  Hello

  I wonder if there is a way that we can limit the number of calls between two subareas, areas or VCS.

  The script as below:

  VCS-E (owncompany) < -----neighbor/traversal/dns="" zone="" over="" internet------=""> > VCS-E (partner)

  My intention is to limit to 5 video calls from VCS-E (partner) so that the 6th call (dial in endpoint) will be blocked.

  I know that we can control the total bandwidth between areas using links & pipes but that does not stop the remote end to lower their rate of recall and deal with several endpoints.

  Thank you.

  Hi Hafiz,

  have you tried to disable the 'downspeed by mode of appeal"in a configuration of Bandwidth?

  try disabling the "downspeed" by call OFF mode under VCS config-. > bandwidth--> configuration.

  This will not allow the calls get the downspeed but it must block because of insufficient bandwidth.

  Thank you

  Alok

• The easiest way to let the client update "editable region."

  I do a site for a band, and they should be able to delete and add text and images of regions editable based on models of web pages.  The leader of the group is computer savvy, but he has not (and reasonably, won't buy) Dreamweaver, much less learn to use it.

  What is the easiest way (for me and for him) to make it what it should do?

  Thanks for your suggestions, you can give me.

  Richard

  In addition to ongoing debates THAT PZ realized you, here are a few free CMS which might work for you.

  (Whatever that you select depends on a) your skills as a web developer and requirements of the b) your customer.

  WordPress is open source, and powerful enough to be used for CMS - requires
  PHP & MySql database.  ++ The learning curve for theme builders first time but
  well supported by multiple hosts.  http://WordPress.org

  Adobe in context - free to use now, but it will cost you later a monthly fee.
  http://www.Adobe.com/products/incontextediting/

  Cushy CMS - very simple. No programming or database required.  The change is
  fact on their servers.  Watch the video to see how it works.
  http://www.CushyCMS.com/

  NanoCMS - is located on your server.  Simple to use. Requires PHP - no database needed. http://nanocms.kalyanchakravarthy.NET/

  Seed - content is located on your server.  Available in ASP, ASP.net or PHP
  versions - no database needed.  http://contentseed.com/

  10 + more free CMSs mentioned here:
  http://woork.blogspot.com/2008/11/10-free-powerful-content-management.html

  Nancy O.
  ALT-Web Design & Publishing
  Web | Graphics | Print | Media specialists
  www.Alt-Web.com/
  www.Twitter.com/ALTWEB
  www.Alt-Web.blogspot.com

• Is there a way I can share files between users on the same Mac without an internet connection?

  Hello world!

  Quick question here: is there a way I can share files between users on the same Mac without an internet connection?

  I have two users say that A and B. If I go the long way via the 'Go' menu > 'Computer', I ended up being told to contact my computer or the network administrator for assistance. Both users are admin one and file sharing is allowed in system preferences... I have to admit that I use 10.9.5 because my MacBook Pro would not work with OS Xs national parks.

  Any ideas would be cool because I'm sure that it used to work fine with "Snow Leopard" without being connected to the internet - or should I just send an email to myself and recover the files on the other user :-) to recover my USB is

  Choose go to folder from the Finder Go menu, provide/Users/Shared/as the path and place the files.

  (142147)

• What is the easiest way to improve the operating speed?

  What is the easiest way to improve the operating speed?

  Buy a new Mac.

  C.

• Concern about the authenticity of a support phone call unsolicited Microsoft

  I received a number of phone calls in the last 24 hours from a caller, saying: it's from Microsoft to support me to eliminate the error messages alert red and yellow of my hardrive system (offline). They are willing to talk to me through this process on the phone.  I'm afraid that it is an appeal from the scam. Can you tell me if Microsoft does indeed support calls at t customers its nature or if I should ignore this caller if they ring again.

  j* address email is removed from the privacy *

  It's a scam.  Next time you receive such a call tell them you know it's a scam, you tell your friends to be wary, and you have contacted law enforcement and allowed your phone to watch to help apprehend the scammers.  Bet your calls will stop.

  And congratulations to not fall for this scam... a lot of people to fall and suffer pecuniary damage to do.

  http://www.Microsoft.com/security/online-privacy/msName.aspx

  http://www.Microsoft.com/security/online-privacy/phishing-scams.aspx

  http://www.Microsoft.com/security/online-privacy/avoid-phone-scams.aspx

  http://www.mypchealth.co.UK/GuideScam.php

  http://blogs.msdn.com/b/securitytipstalk/archive/2010/03/09/Don-t-fall-for-phony-phone-tech-support.aspx

  Kind regards...

• What woulld be the easiest way to record and save everything that is stored on the computer.

  I am a newbie and the computer is an hp with vista windoows. My question, what woulld be the easiest way to record and save everything that is stored on the computer. Thanks in advance

  I am a newbie and the computer is an hp with vista windoows. My question, what woulld be the easiest way to record and save everything that is stored on the computer. Thanks in advance

  You can read this article on the backup that I wrote: 'Return to top your computer regularly and reliable' to http://www.computorcompanion.com/LPMArticle.asp?ID=314

• which is the easiest way to find the version of the motherboard to download its drivers when his need, when you don't have the manual of the motherboard

  Hello

  I knew that finding ITU version of motherboard or chipset to download the drivers of it .you must click pause / break key on startup then the computer wil show just like the version of the motherboard bios.

  I just tried on my computer to start, to see if it works, I pressed pause/break on start up button to see if it is really to give me the information about the version of the motherboard, but it seems nothing happen. I tried it on my desktop and on my laptop by pressing the pause/break key to reboot but it seems nothing happen .no information about the version of the motherboard.

  I looked in the bios, but there is also no information on the type of card mother and version (or chipset).

  I looked in system information, but there is also no information on the type of motherboard and version.

  so my question now is if you do not have the manual of the motherboard (I know on laptops, that the version of the motherboard is written on the back of it) that way someone may know the motherboard type and version to be able to download the drivers of it if it wil really necessary.

  I just ask this question because I started working with computer repair work.

  Thank you

  Johan

  Depends to a certain extent if a PC brand or not. If a PC brand system driver is available since the manufacturers of PC support site.

  Of Belarc Advisor is a free utility that will provide a wealth of information for PC operation