The hard drive on an external drive without virus imagery etc.

Similar Questions

• Satellite Pro A40: Is it possible to format the HARD drive without disk

  I am passing on a Satellite Pro A40 to a brother. It is in very good condition, but has slowed down over the years. I want to get rid of my data (I have on a new machine) and speed up the system by formatting the hard drive.

  The machine didn't come with a disc for Windows XP, or a recovery CD (just a CD "tools and utilities"). I'm sure the drive HARD will be partitioned, and I can format the drive without such a disc.

  If this is true, how should I do?
  Thank you.

  Hello

  I can't believe that you do not have recovery media.
  The laptop must be supplied with recovery CD, Tools & Utilities CD, and WinDVD.

  But back to your question;
  If you insert a new HARD disk, you will need to use the Toshiba Recovery CD or the original CD of Microsoft Windows to install the operating system.
  The new drive is not partitioned HARD and doesn't have any OS pre-installed!

  If you n t have the original CD of Microsoft OS you can contact the service provider allowed in your country and you can order it.

  I hope I could help

  Good bye

• Can I format the HARD drive without losing data?

  Hi all
  I used the restore CD to solve a problem on my system (blue screen) and everything was formatted... including the partition where I had music etc...

  Is it possible to format my hard drive without losing the data on the partition?

  Hi guys

  To my knowledge it s any recovery procedure, you would use; in both cases the drive HARD will be formatted!
  Using the disc using the Toshiba HDD recovery procedure and recovery HARD drive will be formatted and you will lose the data on the second partition too.

  As far as I know both put the laptop and HARD drive on the same State as on the first day of purchase!

• Is it possible to reformat the hard drive without recovery CD?

  I have a Dell dimension DIm 2400 with windows XP Edition family.

  When you restart, is there a 'F' you can hit and be taken to a screen that allows you to reformat your hard drive?

  
  

• Satellite 1900-603: formatting the HARD drive without losing data

  Hello!

  I have a laptop of Pentecost 2 partitions in one, I have the OS and in others, I have my data, my problem is I want to format the partition with the operating system without losing my data, I intend to use for formatting recovery CD. Is this possible at all?

  Another question, I bought my laptop on the Switzerland but I am Portuguese is it possible to get an in Portuguese of toshiba recovery cd?

  Thank you

  Hi Rita

  It is of course possible.
  I assume that you installed your operating system on the first partition and all important files are placed on the second partition.
  The recovery procedure contains the standard and expert recovery mode recovery mode.
  You must choose expert mode. Here it should be possible to choose the partition where the OS image must be installed.

• then I just remove my hard drive without crashing the system

  I just back up files on the HARD drive. There is no system files or programs on it. Can I remove and replace it with a bigger memory HARD drive, without crash the system?

  Yes, you can remove the HARD drive without crashing the system by closing the PC, unplug the power supply from the socket and then remove the HARD drive.

  Please note that the physical HARD disk is different from scores.

  Hard physical HARD drive or disk drive is the hardware component for storage. The capacity varies.

  A HARD disk cannot be used directly when it is connected to a computer, that's why storage units with file tailored to the needs of the system to create, known as partitions.

  A partition can be a complete HDD (for example, if you have a physical HARD disk and you have only one partition C:\) or may be more than one partition of a physical HARD disk (for example, if you have a HARD physical disk and two or more than two partitions, such as C:\ and D:\).

  Therefore, you can check for the exact physical HDD and then remove it. To do this, you can go to the computer-> storage management. Check the link for more information:

  http://www.7tutorials.com/how-manage-your-disks-using-disk-management-utility

  This will show you the number of physical drives present in your PC and the partitions present in each HARD drive. So, once you confirm the HDD backup and partition (make sure that there no Windows installation, as says iFuton), you can shut down the PC, unplug the power supply and then remove the HARD drive.

  [Please note that you have nothing to do in the management of the computer, except to check the partitions and hard drives (denoted as disk 0 disk 1 and so on for disks hard physical as well as the corresponding scores appear accordingly)]

• Wizard BootCamp 6.0.1 running on El Capitan 10.11.5 installs single partition BootCamp on the disc Fusion consisting of 128 SSD part G SSD and 3 TB of HARD drive on an iMac (retina 5K, 27 inches, end of 2014), but not the part of the HARD drive?

  How is it assistant BootCamp 6.0.1 running on El Capitan 10.11.5 installs single partition BootCamp on the disc Fusion consisting of 128 SSD part G SSD and 3 TB of HARD drive on an iMac (retina 5K, 27 inches, end of 2014), but not the part of the HARD drive?

  This has two questions:

  1 capacity of SSDS faster for Fusion drive has been reduced. Therefore less effective for the reader of the merger. For example if I need to create a partition of 80G for my windows bootcamp partition, only 48 G will be left in the drive of the merger.

  2. ability of the bootcamp windows partition becomes very limited, cannot be greater than 120 G.

  3. even when I try to fuse out of the drive of fusion in the 128 G SSD and 3 TB of HARD disk, and then run the BootCamp assistant to create the bootcamp partition start from scratch to reinstall El Capitan only on the HARD drive (without drive Fusion), it won't let me do anything, it just shows an error that says something like "a person has created additional partitions on this drive please select. another disc. But there is nothing else to choose.

  Before my (5 K, 27 inches, end of 2014 retina) to El Capitan Yosemite, I was able to use the previous version of the wizard BootCamp 5.x to create the partition, bootcamp on the drive of the merger. And it will be divided in the fuser unit in two and insert the Bootcamp partition (with the size I chose, which can go up to 1 TB) between two partitions of MAC OSX.

  The disk partitions resulting from it, will be the partition MAC OS x on the SSD, the partition MAC OS x on the HARD drive partition #1, partition MAC OS x on the HARD drive partition #3.

  Then there is the BootCamp partition on the HARD drive partition #2.

  Is there a way to get what I need?

  That is what has been described in this notice of two canoes?

  Installation of Windows on a Boot Camp partition on a drive of TB Fusion 3

  n-on-a-3-TB-fusion-drive http://twocanoes.com/Winclone/support/installing-Windows-on-a-Boot-Camp-partitio

  Thank you.

  After having worked on those weeks, I realized that I need very painfully (by first going back to Yosemite and bootcamp 5 to escape all the limitations of El Capitan and BootCamp 6) I want to share here. Someone at - it other smarter solutions welcome.

  Note these steps and mentioned drivers only work for my version of iMAC, retina 5K late 2014. If you have other material, please search on the web to see which driver will work first. And all of these steps are destructive and assumed that you first take backup. It is only shared for interest only. Readers will have to bear your own risk.

  A. take backup

  1. take a backup completes my iMac Fusion Drive using Time Machine. Then restart with a Yosemite USB installation and select Terminal from the menu on the top bar.

  B. fuse out of the merger in two physical disks drive: SSD + HDD

  1. in the terminal, type the commands in show what the logical volume group ID and the ID of the logical Volume of the disc fusion)

  Cs diskutil list

  2. in the terminal, type commands for the fuse of the fuser unit and separate them to an SSD and a HARD drive.  Note: All data will be destroyed in the drive of the merger. There are many articles in this community on how this could be done,

  diskutil cs deleteVolume Logical Volume ID

  CS diskutil remove logical Volume Group ID

  This should finish within 30 minutes. If you have taken more time, this means that your reader of fusion has been altered somehow.

  I hit this issue too.  To use this command to remove the fusion drive hung up, and I need to do the hard to scramble a few sections of data in the hard disk partition table using the controls to tell the OSX this hard drive is a new without partitions:

  Cat >/dev/random /dev/disk0 (where/dev/disk0 is the SSD)

  and repeat for disk1/dev/disk1 which is the HARD drive in my case).

  This command will not return anything, but expect to press Ctrl-Z to end after 1 minute.

  2 create independent partitions (non-fusionend) for the installation of OSX.

  Borne Terminal output, and select disk utility, in disk utility, select the drive to HARD disk (and not on the partition), you will see the error message and you will be asked if you want to fix the fuser unit, click on ignore. Then wipe the HARD drive to create a single 'extended OSX journaled"named"HARD drive".

  3. Repeat step 2, and then erase the SSD drive to create a single 'extended OSX journaled"named"SSD ".

  C. install on the HARD disk as drive didier autonomous not fusion.

  1. go to Yosemite install screen and proceed with the installation of a clean copy of Yosemite to the iMAC. then connect you.

  D. use BootCamp Yosemite f5 to install windows.

  1. launch Yosemite bootcamp.

  2. check the two checkboxes for creating the USB drive to install windows 7 or a later version, and to download the windows supports the Apple software.  Do not click on the last box to install or remove windows pie creating real bootcamp partition again.

  3. it may take several hours to complete this function of your internet b/w and also performance of your USB drive.

  4. If you install Windows 7 (like me), then the downloaded drivers will not work for you, this will cause the issue of the device driver appleDSS.sys does not like this driver and others are too recent for windows 7 to use.  Also, your keyboard and mouse may not work even if you try to plug in a USB external keyboard or a mouse. You need to replace the drivers downloaded by others (the Boot Camp 5.1.5769 drivers that I find in this link: Software Support of Boot Camp 5.1.5769.) (Note: this driver is material specific only works for my iMAC model).  Once you have downloaded it, copy the two files in the root directory of the USB installation to replace the original ones. It's specific and material available for download somewhere on the Apple Site.

  -From the Finder, delete the $WinPE$ and the Boot Camp of the FLASH PLAYER files.

  -Expand the old drivers for Boot Camp 5.1.5769 (two records and another file) on your desktop.

  -Copy the $WinPE$ and records of Boot Camp in the FLASH PLAYER.

  5. open Boot Camp Assistant again and only select the third option, install Windows 7.

  It will show you the screen to select what installation disk, select HARD drive.

  Then drag the slide bar to select the size of the Bootcamp partition for windows you want, knowing that there is a restriction for windows installed using training camp on a MAC that the last byte of the BootCamp partition must reside in the first byte of the 2.2 T of each physical hard drive.

  For my case, I need only 500G for bootcamp and leaving behind 1.7 to for my MAC OSX partition immediately after the bootcamp partition and an another 0.8 T MAC OSX partition after him. 1.7 TB and the partition of MAC OS x 0.8 TB well exploited in the meantime bootcamp partition, will be merged into a fusion drive by Bootcamp. Thus, you will end up with total 2.5 TB of disk space in a logical drive - fuser.

  Go to this link for more details on this subject: n-on-a-3-tb-fusion-drive http://twocanoes.com/winclone/support/installing-windows-on-a-boot-camp-partitio

  6. continue the process to partition the hard drive, then it will restart automatically in windows installation mode, install windows.

  7. once the installation is complete, check that windows is functioning correctly.

  E. Si you want to upgrade to windows 10 Windows 7.

  1 if you plan to upgrade to windows 10, you'll find that the windows IE v.8 7 is no longer works and had many problems to load the page.  Then when you try to download the latest version of Internet Explorer, you get an error that you need at least windows 7 SP1 to support the last IE.  Life is too complicated, just download the google Chrome browser, then search for download windows 10 and then run the Microsoft valuation tool to upgrade.

  2 but before upgrade you, unplug all your MAC USB drives, otherwise, you will find that, after having spent an hour downloading the windows 10 software, the upgrade will fail with the error "/ dynamicupdate...» ». It is an inexplicable mistake that no one seems to understand why. There are articles with proven results that the removal of all USB drives before running the windows 10 upgrade tool will correct this problem.

  F. reinstall OSX El Capitan

  Once your target windows system (if windows 7, windows 8 or windows 10) works very well.  You can continue to create again your Fusion drive and reinstall OSX El Capitan.

  1. Insert the install of OSX Yosemite rear USB to the iMAC, and then select Restart Windows, or stop, and then turn the MAC once again.

  2. When you hear the ringing tone, press on and hold down the option key for 10 seconds. Then you release.

  3. on the selection screen, select start Yosemite OSX install drive.

  4. after starting, do not proceed to install OSX El Capitan again. But select Terminal from the menu bar.

  5. in the terminal, type the command 'diskutil list cs' and you should see nothing to prove that there are no existing fusion drive yet.

  6 type the 'diskutil list' command to list all disks and partitions.

  The SSD has two partitions, the/dev/disk0s1 of EFI (209 MB) partition and the other/dev/disk0s2 of OSX partition we created in step B above, called SSD around 121 G.

  The HARD drive has two partitions, the/dev/disk1s1 of EFI (209 MB) partition and the other/dev/disk1s2 of OSX partition we created in step B above, called SSD.

  G. delete the logical storage of nucleus on the HARD disk drive and it refuses with the DSS to form a merger with faster performance disc

  1. Insert the install of OSX El Capitan rear USB to the iMAC, and then select Restart Windows, or stop, and then turn the MAC once again.

  2. When you hear the ringing tone, press on and hold down the option key for 10 seconds. Then you release.

  3. on the selection screen, select start Yosemite OSX install drive.

  4. after starting, do not proceed to install OSX El Capitan again. But select Terminal from the menu bar.

  5. in the terminal, type orders for (to show what are the logical volume group ID and the ID of the logical Volume of the logical drive). You should see the logical volume to basic storage group created using two partitions on the hard drive, 1.7 TB and TB 0.8 created when we run the Yosemite Bootcamp to install windows.

  Cs diskutil list

  6. in the terminal, type commands to delete logical drives from basic storage.  Note: All data will be destroyed in the logical drive.

  diskutil cs deleteVolume Logical Volume ID

  CS diskutil remove logical Volume Group ID

  7. tap "diskutil list" command lists all the resulting partitions. You should see that the HARD drive has the following partitions.

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 121,3 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_HFS GB SSD 121.0 disk0s2

  / dev/disk1 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * 3.0 to disk1

  1: EFI EFI 209.7 MB disk1s1

  2: Apple_HFS 1.7 Untitled TB disk1s2

  3: disk1s3 Apple_Boot Recovery 650.0 MB HD

  4: Microsoft database BOOTCAMP 503.0 GB disk1s4

  5: Apple_HFS 801,4 Untitled GB disk1s5

  8 type the following commands to create the logical volumes group, named "myLVG" (or the name) of fuser using the usable for OSX to the SSD and HDD partitions.

  diskutil cs to create "myLVG" disk0s2 disk1s2 disk1s5

  Note: Mark the group id of logical volume shown in the results.

  In my case, I want to book the last partition as standalone partition disk1s5 no-fusionend, so I can use it to raise the back, or format it in FAT32 to allow the exchange of data between the MAC and boot camp.

  So, I do not understand this last partition in the drive of the merger. in my case, the command that I used is: diskutil cs to create "myLVG" disk0s2 disk1s2

  9 create logical volumes named "Macintosh HD" (or you call it) on the logical volume group we just created for the reader of the merger.

  diskutil createvolume logical volume group ID jhfs cs + 'Macintosh HD' 100%

  10 command "diskutil cs type list" to check the resulting fusion drive created.

  CoreStorage groups of logical volumes (1 found)

  |

  + Logical Volume - Group F53C7A25-C2F3-4997-91E9-2E6B6BAB2E0E

  =========================================================

  Name: LVG

  Status: online

  Dimensions: 1815635525632 B (1.8 to)

  Free space: 90112 B (90.1 KB)

  |

  +-Physical volume E176873C-7C80-4759-8110-BA7307E0C4B3

  |   ----------------------------------------------------

  |   Index: 0

  |   Disc: disk0s2

  |   Status: online

  |   Dimensions: 120988852224 B (121.0 GB)

  |

  +-Physical volume 6535AC3C-DCF8-453F-AD47-98905538386E

  |   ----------------------------------------------------

  |   Index: 1

  |   Disc: disk1s2

  |   Status: online

  |   Dimensions: 1694646673408 B (1.7 to)

  |

  +--> Logical volume family F3D15F87-FB84-4B43-B2F2-E9EACC7C42D9

  ----------------------------------------------------------

  Encryption type: no

  |

  +--> Logical volume 0D807F6E-FB7C-418F-AAF4-EF3EA3525D10

  ---------------------------------------------------

  Disc: disk2

  Status: online

  Size (Total): 1809780178944 B (1.8 to)

  Reversible: no

  Name: Macintosh HD

  Volume name: Macintosh HD

  Content indicator: Apple_HFS

  LVG Type: Fusion, sparse

  11 exit the terminal, go back to OSX El Capitan install screen and select the name of the fuser unit 'Macintosh HD' proceed to begin the installation of the os x for installation.

  12. There will be a step in the installation ask you if you want to configure as a new computer, or restore from a time machine previous backup. Make your own choices it accordingly.

  13 once OSX El Capitan has been installed and you have finished restoring the data and custom configurations, you can enter the application of preferences to check if you see the icon of the "Startup" disk", and if you choose Startup BootCamp in the next reboot, you should be able to boot up to Windows without pressing and holding the button option when reboot and choose to start windows manually. Also, in windows, you should be able to click on the bootcamp Control Panel and select for a startup to OSX on the next reboot.

  14. one thing to be aware, if you install bootcamp in this way, the boot camp and the GUI utility disk in OSX El Capitan will not be able to adjust your settings. This means, if you need to touch anything or to readjust the size of the partition, you will need to do it again in step A. Alternatively, some how to get started with installing Mac OSX Yosemite USB, then adjust the partitions using similar commands shown in this article or other articles in this community.

  15. yet once please take personal responsibility on damage if you follow the instructions in this article.

• Tecra M5 - how to remove the HARD drive password generation?

  +++ Problem +++

  No change possible 'Building in HDD Password'.
  The generation in HARD drive password' is known - but cannot remove the 'build in HARD drive password'.

  +++ Progress +++

  (1) parameters of the BIOS "Password."

  Is not registered

  (2) the "HARD drive password" BIOS settings

  HARD = built-in HARD disk drive
  Password disk HARD = only user mode
  Registered = user password

  +++ Procedure +++

  Change the setting "User Password = recommended" with BACKSPACE
  of 'user password = Registered' to 'user = password [empty]. "

  It follows the question: ' are you sure? [Y/N] »
  With this screen, the "User password" settings are changed back on "registered."
  No message appears as "Disabled" or empty cell.

  After the confirmation on my side, the laptop starts without asking 'building in HDD Password.
  After restarting the laptop (2nd) ask the requested 'building in drive HARD password '.

  +++ Request: +++

  How is it possible to remove the 'building in HDD Password'?

  Background is to create an image file from the hard drive without the laptop original.
  So all the security settings should be disabled on the hard drive.

  Your support is welcome

  Kind regards
  ML

  Post edited by: Mluepke

  Hello

  I know, HARD drive password can not be deleted. Please see the follow-up documents:
  http://APS2.toshiba-tro.de/KB0/TSB6B01MC000CR01.htm
  http://APS2.toshiba-tro.de/KB0/FAQ9401AR0000R01.htm

  Good bye

• Replacing the hard drive not detected in windows 8 clean install

  I have a Dell latitude E6330 and my HDD recently crashed. With the replacement hard dive, I could not clean install windows 8. The BIOS indicates the presence of the hard drive without problems diagnosed but windows 8 installation a driver is needed in the initial phase. I have also seen a showin error invalid partition table. Are there compatibility issues. Its a Toshiba SATA 500 GB drive

  You may need to load see above-SATA drivers:

  http://dellwindowsreinstallationguide.com/a-clean-install-of-Windows/downloading-preparing-and-loading-SATA-drivers/

  Use these ones:

  http://ftp.Dell.com/FOLDER01716106M/27/DRVR_SATA_Intel_A00_C8P0T_f6flpy-x64-setup_ZPE.exe

• I can't access my external hard drive with windows 7. How can I get my music out of her files? My pc with xp operating system can access it without problem. but my new pc with windows 7 does not see the hard drive.

  I bought a new pc to replace my old hp 14 months as the motherboard fried in. I bought a case of disk external hard to rocketfish to put the hard drive of my Windows 7 pc in. burned does not see the hard drive. my old pc with xp can access all the items on the external hard drive.

  Check that the drive appears in Device Manager.

  If so, go to disk management and assign a drive letter.

• How to switch my system on a larger hard drive without having to reinstall the OS and lose my data?

  replace the hard drive

  I'm looking to replace my hard drive but I need all the files it is about it, passing a small hard drive to a larger hard drive. My question is how can I save all the files on the disk and how can I get the operating system on the new hard drive without the original disk

  If your current system does not work, there is no need to bother with data backup, installation of applications and get a Windows XP installation CD (although regular backups are important to do as a general practice).

  Instead, clone your current hard drive to your new hard drive.  All you need is an external hard drive enclosure and disk cloning software.  In addition, once you have made sure that everything works correctly, put the old drive in the external box and use it for backups.

  Some of the cloning apps below are also disk 'images' (e.g. Acronis True Image).  A disk image can be compressed so that, for example 58 GB of data can produce a 40 GB image file.  Some of the apps, and of also can selectively backup specified files.

  The housings of external drives more to connect to a USB port.  Make sure just that buy you one with the good 'form factor' (portable = 2.5 inches, computer desktop/Tower = 3.5 inches) and internal drive connector.  Many but not all speakers can deal with SATA and PATA time.

  This example (for laptops) is not the less expensive external hard drive enclosure, but it's a decent case that can be used with either SATA or IDE (PATA) drives and comes with its own software package of cloning: http://www.newegg.com/Product/Product.aspx?Item=N82E16817155602

  It is a very good buy for a drive IDE (PATA) Office size: http://www.newegg.com/Product/Product.aspx?Item=N82E16817155602

  In general, Newegg is a good place for your search options by looking at the comments by users.

  If you have a Western Digital hard drive, you can get a version of Acronis True Image free of WD (http://support.wdc.com/product/downloaddetail.asp?swid=119) or you can get the software of cloning separately (this is not an exhaustive list and in no particular order, some are free, some not):

  Acronis True Image Home
  EASEUS ToDo Backup
  Paragon Drive Copy or Partition Manager Personal
  Casper
  Norton Ghost

  XXClone

  Macrium Reflect free

• How can I get Windows 7 to read RAW hard drives without having to format the hard drive due to important work on this subject?

  Original title: the file format of external hard drive is the RAW and not NTFS. How can I get Windows 7 to read RAW hard drives without having to format the hard drive due to important work on this subject?

  I put the hard drive on an XP and Vista machine and can read the hard drive, but not with Windows 7

  Hi Zling,

  It works on other OS? When did you finally read the disc and with what OS? If you can read the drive and make a backup of the data on this subject, I you suggest to backup the data on the drive and then put it in using the NTFS file system.

  I hope this helps! Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• How to put Windows 7 on the new hard drive without boot cd? How will I know if 32 or 64 bits? This computer yourself running windows 10?

  * Original title: windows 7 download

  I have a laptop dell M4400 with windows 7 pro OA. HARD drive crashed and I replaced with a new one. How to put Windows 7 on the new hard drive without boot cd? How will I know if 32 or 64 bits? This computer yourself running windows 10?

  It has probably comes with Windows 7 Professional 64 bit.

  You can download a copy of Windows 7 Professional using the following instructions (update of Microsoft recovery software supports downloads with the COA key):

  How to: What are my options for Windows 7 reinstall media?

  Make sure you scroll down and read the section:

  What to do if you cannot get your manufacturer recovery media, refuse to use or to buy it or the Microsoft Software Recovery Website does not work?

  You can also use Windows 10 too as you have the right to it as a free upgrade:

  • How to download official Windows 10 ISO files
  • How to: perform a clean installation of Windows 10
  • Turn off (preferably uninstall) your Antivirus utility before you perform the upgrade.
  • Reboot several times, and then try again.
  • Disable the general USB peripherals (for example - smart card reader).
  • If you are using a SCSI drive, make sure you have the drivers available for your storage on a thumdrive device and it is connected. During the installation of Windows 10, click on the advanced custom Option and use the command load driver to load the driver for the SCSI drive. If this does not work and the installer still fails, consider switching to an IDE based hard drive.
  • Perform a clean boot, restart, and then try again.
  • If you upgrade to the. ISO file, disconnect from the Internet during the installation, if you are connected in LAN (Ethernet) or wireless, disable both, then try to install.
  • If you are updated through Windows Update, when download reaches 100% disconnect from the LAN (Ethernet) Internet or Wi - Fi, then proceed with the installation.
  • If this does not work, try using the. ISO file to upgrade if possible.
  • If you are connected to a domain, go to a local account.
  • If you have an external equipment, attached to the machine, unplug them (example, game controllers, USB sticks, external hard drive, printers, peripherals not essential).

• I currently store my pictures on and an external hard drive.  Lightroom 6 was not able to find the picture momentarily files.  I inserted an external Flash DRIVE after removing the hard drive and the computer renamed the stick with the same drive letter t

  Redesign existing external hard disks and still 6 Lightroom able to find existing photos.

  I currently store my pictures on and an external hard drive.  Lightroom 6 was not able to find the picture momentarily files.  I inserted an external Flash DRIVE after removing the hard drive and the computer renamed the stick with the same drive letter that has been designated by Lightroom to store my photos.  I could go into my Windows 10 and reset the player to the letter that Lightroom has given at the beginning of the external hard drive.   However, I know this can happen again, if I connect any stick USD or another device, while the external hard drive is not connected to my laptop.   I found the information that I can do the new designation of the final drive by choosing a letter it is 1/2 way or higher in the alphabet.   I would like to turn an external hard drive on a strong letter, warns we hope this previous problem.   My question is, if I already have a lot of pictures on this external hardrive with the designation of the current drive, how it becomes a higher letter and have 6 Lightroom recognizes files, now under the new designation of drive letter without having to go to each photo individually and manually force Lightroom 6 find each photo.  It would take more time than I'd like to lose.  Is there a way to get just 6 Lightroom to recognize the new disk designation has changed and is able to find all of the existing files?

  I have read the ADOBE LightRoom 6 manual and seem not to be able to find anything on how to do it.

  Any help would be welcome.

  Thank you!

  So in Windows, you can select a drive like q letter (or any other letter you want only towards the end of the alphabet)

  Then in Lightroom, you can reconnect to the photos on q: the following instructions (see specifically 4 Figure and related text)

  Adobe Lightroom - find moved or missing folders and files

• Recovery of DNG issue: I have photos stored on an external hard drive which have previously been imported into Lightroom and converted to DNG.  The laptop on which I was running Lightroom died and I had to replace the hard drive and rebuild the

  Recovery of DNG issue: I have photos stored on an external hard drive which have previously been imported into Lightroom and converted to DNG.  The laptop on which I was running Lightroom died and I had to replace the hard drive and rebuild the computer.  In the process of my Lightroom program and catalog related to these images have been lost.  When I re-associate these photos with my new installation of Lightroom and a new catalogue is there a way to retrieve the keywords or other changes or metadata catalogue Mountaga?  Is any of this information embedded with the imge DNG file or was it only in the cataloght lost on my failing hard drive? I re-import just as if it were new images with no prior treatment of Lightroom?

  By default, LR saves all changes in the catalog, and that applies to any type of file.

  Optionally, you can save changes to the file as well, for raw files owners, this will create a xmp file - for DNG that changes are going to be cooked in the file, without additional xmp file.

  But it does not default. Go to the catalog and parameters under the control of metadata automatically save changes to XMP.

  Unless you do this, the changes are saved only in the catalog.

  Hope this makes things clearer.