The message at startup: SATA drive secondary 0 not found.

I have a computer Dell XPS Generation 2 with two SATA drives not configured in RAID.  Initializing the BIOS, I get the message: SATA drive secondary 0 not found.  Press F1 to continue or F2 to enter Setup.  If I enter the configuration, I find:

Primary SATA drive

Model ST3120026AS

120 GB

SATA secondary drive

Unknown device

If I press F1 it will load Windows XP.  How can I access my secondary SATA disk?  My BIOS is V A06.


Tags: Dell Drives

Similar Questions

  • After the closure of Windows XP on my medion Tower desktop computer it now primer not. The message I get is Retten.exe file not found.

    I have a Medion Tower Office that, like fine until this last time, I closed Windows and now won't start or switch to safe mode recovery mode, ect., the message I get is unable to find the retten.exe file. It will not allow even me to re - install Windows xp from the disk that came with the desktop computer. Can any help?

    Thank you

    Hello

    ·        You did changes to the computer before you shut down the computer?

    You can try to boot from the CD and perform a disk check, and check if that helps. You will need to change the boot order in the BIOS (Basic Input/output System) and check if that helps.

    Warning: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

    Start Recovery console, and then run the disk check. To start Recovery console follow the link below.

    http://support.Microsoft.com/kb/314058

    Note: To start the recovery console, you need the Windows XP installation CD.

    Once you start in the recovery console, follow the link to perform the disk check.

    http://support.Microsoft.com/kb/315265

    You may need to contact the manufacturer for support.

    http://support.medionusa.com/

    Amrita M

    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • I get the message error 1327.invalid drive: M:------tries to install a nuance product

    I try to install dragon naturally speaking and I get the message, Error 1327.invalid drive: M:------.

    How can I fix it

    Hello

    You can try these:

    a. log on as an administrator or as a member of the Administrators group.

    b. Click Start, click Control Panel and then click on performance and Maintenance.

    c. click on Administrative Tools, double-click computer management and then click Disk Management in the left pane.

    d. right-click on the CD ROM drive and click change drive letter and paths.

    e. click the button modify and change the drive to K and then click Ok.

    f. click Yes to confirm.

    g. install Dragon Naturally speaking

    See also: http://nuance.custhelp.com/app/answers/detail/a_id/5720

  • PE R510 of the SAS addition to the installed system with SATA drives

    Hello

    We have a server PE510 that came with 2 drives 2 TB SATA 7.2 k and a Controller PERC SAS 6/iR.   The servers of the machine as a SQL server (its original purpose) and later on, a busy file server.  The file server role was not originally intended for this machine.  What we are seeing is very bad I/O bottleneck during daily use, although only about a dozen people access to this server.   (I got the system extracted by pressing more than once).

    I wonder if replace drives with SAS will help solve this problem.  There are 6 empty bays on the system.

    Would I be able to add 3-6 SAS disks to this system (in addition to the installed SATA disks), in order to create a new RAID volume and move the files to it on SATA volumes?   The existing SATA drives are in a RAID1 volume.

    Thank you

    Thank you

    Mauricej74
    I wonder if replace drives with SAS will help solve this problem.  There are 6 empty bays on the system.

    Replacement by SAS will probably help, but your bottleneck is your controller, not your type of disc.  There is no easy way to migrate a Windows installation of a SAS 6/iR to a PERC 6 / i, but if you were to move the PERC, you will see a substantial improvement.  The other problem is that, because you can not mix SAS and SATA disks in a virtual disk, you would have to do a backup/restore for the SAS VD (you would not be able to rebuild a SAS drive in the existing table to replace one at a time).

    Mauricej74
    Would I be able to add 3-6 SAS disks to this system (in addition to the installed SATA disks), in order to create a new RAID volume and move the files to it on SATA volumes?

    Yes, you can add the SAS drives for the system and more SATA drives.  Note, however, that 1) the SAS 6/iR controller only supports 2 virtual drives, while a VD can be added, and 2) the SAS 6/iR controller only supports RAID 0 and 1, would be so the only way to add disks "3-6" in a RAID 0, which leaves your data at extreme risk.

  • at startup, I mesg.drive get 1 not found serial ATA, SATA2 and drive 3 not found parralell ATA, PAT-1 (PRI IDE SLAVE)

    at startup, I mesg.drive get 1 not found serial ATA, SATA2 and drive 3 not found parralell ATA, PAT-1 (PRI IDE SLAVE)

    Hi waynehile,

    1. are you able to boot into Windows after the error message?

    2. did you of recent changes on the computer?

    3 when was the last time it was working fine?

    Usually, this would happen if the hard drive is not set correctly in the basic input/output system (BIOS) or the settings in the basic input/output system (BIOS) are incorrect.

    Basic input/output system (BIOS) is a program built into personal computers that starts the operating system when you turn on your computer. It is also referred to as system firmware. Basic input/output system (BIOS) is part of the hardware of your computer and is separate from Windows.

    For more information about the correct settings in the BIOS of your computer and how to check and change these settings, see your computer documentation or contact the manufacturer of your computer.

    Important: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  • Receiving the message "Wireless association failed because Windows did not receive response from the access point or wireless router" _

    My laptop was working fine yesterday, but when I started it today I get the message "Wireless association failed because Windows did not receive response from the access point or wireless router.

    I can see my network and I can connect to the internet using my desktop pc, but just to make complicated I can't even connect to the network when I plug the ethernet cable into my laptop.

    I think it might be a driver problem, but I have no idea how to solve this problem without access to the internet on my laptop.

    I'm running Vista and my wireless router is an Atheros AR5009 809.11a/g/n

    I need step by step instructions on this Yes please treat me like a fool!

    Thank you

    Laptop would not work at home thus concluded that it was a BT Broadband do not issue my driver (despite BT telling me the opposite last night)

    After the call to a fantastic Lady in BT it's all fixed and thanks to Jack I now know a lot more on connecting wireless to my laptop!

  • I can't open my email on Firefox, it works on explore. When you go to the page I get this message "the requested URL /hunter/ajax_login/redirect.php was not found on this server."

    Question
    I can't open my email on Firefox, it works on explore. When you go to the page I get this e message "the requested URL /hunter/ajax_login/redirect.php is not found on this server."

    Reload Web pages, and ignore the cache.

    • Hold SHIFT and click reload.
    • Press 'Ctrl + F5' or 'Ctrl + Shift + R' (Windows, Linux)
    • Press 'Cmd + Shift + R' (MAC)

    Clear the cache and cookies from sites that cause problems.

    "Clear the Cache":

    • Tools > Options > advanced > network > storage (Cache) offline: 'clear now '.

    'Delete Cookies' sites causing problems:

    • Tools > Options > privacy > Cookies: "show the Cookies".
  • NTBackup error: "the saved selection file 'Drive.bks' is not found."

    The server used to back up the C drive very well, then from the year last it started giving me this error. No updates or changes made to the system as far as I know - so I'm puzzled as to why I get this error (found via the errorlog of the applications of computer management)

    Details
    Windows Server 2003 R2 - Standard Edition
    Using backup utility

    Here's the line of 'code' of the backup utility
    C:\WINDOWS\system32\ntbackup.exe backup "@C:\Documents and Settings\Application Data\Microsoft\Windows NT\NTBackup\data\C Drive.bks administrator" / n "Sauveg.bkf created on 02/06/2009 at 14:34" /d "Set created on 02/06/2009 at 14:34" / v: no r:no /rs:yes / HC: off /m normal /j "Drive C" /l:s / f 'E:\C Drive\Backup.bkf '.

    I looked in the phone book and Drive.bks C is there, so I'm confused as to why its say Drive.bks is not found

    I also tried to change the name of the files, so there's a space (IE CDrive.bks etc), but there is no that tell me that CDrive.bks is not found
    Another thing, I have another job scheduled exactly the same thing, but for some personal files on a different drive, which is backup fine.

    any help or idea would be great

    Hello

    Your Windows 7 is better suited for the public of Windows Server on TechNet. Please post your question in the TechNet Windows server forum.

    http://social.technet.Microsoft.com/forums/en/category/WindowsServer

  • The message I get is Microsoft word has not been installed for the current user. Please run set up to install the application. I reinstalled the software, but get the same message.

    The message I get is Microsoft word has not been installed for the current user.   Please run set up to install the application.   I reinstalled the software, but get the same message.

    Hello

    See the methods listed in the articles below and check.
    You receive an error "Microsoft has not been installed for the current user" message when you try to start an Office 2003 program or an Office XP program for the first time
    http://support.Microsoft.com/kb/898512
     
    You receive a message "Microsoft has not been installed for the current user" when you start an Office XP program or start of Microsoft Office Maintenance mode
    http://support.Microsoft.com/kb/298022

    I hope this helps.

    Thank you, and in what concerns:
    Shekhar S - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.
    If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • error packaed and launch: Oh, Snap! Build request failed with the message: [ERROR] an archive or directory does not exist in the specified path:

    Hello

    I get this error when you try to run the sample of cards on the corrugation Simulator:

    Oh, Snap! Build request failed with the message: [ERROR] an archive or directory does not exist in the specified path: "/ Users/Calgacos/Library/Application Support/Google/Chrome/Default/Extensions/cnijnnaimeaacneklcndcafbnkeicckh/0.9.16_0/services/node/node_modules/rbd/Packaged/Maps.zip".

    The .../rbd/Packaged folder is writable and the Maps.zip will be created in the folder ~/RippleSites/Maps/Packaged.  With the help of Mac, the latest versions of everything.  The application runs in undulation ok, but I can't throw on the SIM BB10.

    Someone else have this error and know why?

    PS the Maps.zip does not get created (or copied) in specified folder, of course, but why?

    PS try another application and it worked but is too has not put its zip file into the folder... rbd/Packaged.  I guess it should not but leaves me clueless as to whats wrong with cards.

    Thank you

    The two directories (in the extensions directory and maps project directory) have permissions to 777.

    But you gave me an idea...

    It turns out that simply by putting

    "Packages".

    in setting output wasn't enough, I need the full path

    for example: "/ Users/username/RippleSites/Maps/packed."

    and presto, now it works!

    Thank you!

  • The messages tell me that windows 7 is not genuine.

    The messages tell me that windows 7 is not genuine. I bought it on Ebay and it worked fine for 2 years, but a month ago he started telling me that I have counterfeit software.
    Any ideas?

    Thank you.

    your product key has been blocked.

    Windows product ID: 00426-068-1702047-86092

    The ID of the product - 068 - indicates a not for resale MSDN account. If you are not the account holder and you bought it in a box at retail, the box and its contents is counterfeit. Request an immediate refund from the seller

    For more information, see this:

    http://social.Microsoft.com/forums/en-us/genuinewindows7/thread/a2444f34-0AFF-4f29-a8ac-67e28b0c0285

    And this:

    http://social.Microsoft.com/forums/en-us/genuinewindows7/thread/309bb621-92d5-43d6-98c1-2bb51b35607f

    To see how these counterfeits are more, see:

    http://www.YouTube.com/watch?v=hzqNNiOM0cs

    You will need to buy a legitimate windows from a legitimate retailer or go back to the windows, your computer comes with that.

  • I get thid message RUNDLL C;\windows\momowsi.dll is not found.

    original title: Please help!

    I get thid message RUNDLL C;\windows\momowsi.dll is not found.

    When a Google search for a results file name in no hits or suspicious hits, the answer is usually that the file in question is linked to the malicious software and your anti-malware application has deleted or quarantined file, but left to the Windows registry entry that tries to start the malicious software when you start your computer.

    First of all, download, install, update and run both of these free analysis tools:
    MalwareBytes AntiMalware
    SUPERAntiSpyware

    Do not run the scans at the same time.  They can take some time, so start an and then go for a non computer chore for awhile.

    If the scans does not solve the problem (and they can't, because the actual malware file has already been processed), then download and run Autoruns.  Click on the "Connection" tab and look in the column 'Image path' for the dll named in your error message.  If it is not displayed in the connection tab, click the "all" tab and use the file > search tool.  A characteristic of the search of Autoruns tool is that you must move the selection under the element line "found" before you "Find Next."

    Once you find the line with the file in question, either "delete" or (if you want to be safer) uncheck the box.  The latter prevents the line running, but you can reactivate it later by removing the check mark.

  • Cannot find the XP drivers for Sata Drive

    I can't find the XP 32-bit drivers for my sata 750 GB sata HD model WD7500BPVT, I watched all the other Messages in this forum, but I can't find a thing.  I looked hard into the laptop Sata Drive and next to him it's a model Sata 750 GB WD7500BPVT he says also to replace this drive with a 634250-001, and there is a barcode below what has the nubers DC12CD so this is useful because I thought that it also my being the model player.

    Hello:

    The sata drivers, you need to depend on of which laptop model you have (processor and chipset), not which hard drive model you have.

  • «Get the message at startup...» "Host process for Windows Services has stopped"... and sometimes losing his

    I started getting a message every time I boot my laptop Compaq Presario CQ60. Message is "host process for Windows Services has stopped". My speaked symbol now has a red cross I've ever had before. When it turns off I often have not all sounds. I have a feeling that this has happened after an automatic update. I did a system restore, but this does not solve the problem. It's the sound that is most annoying that I never know when or where I will not have it. I hope someone can help

    To clarify, the two problems was started at the same time?

    Try to perform a clean boot in an attempt to determine the cause of the error at startup:
    http://support.Microsoft.com/kb/929135

    Try reinstalling the latest audio drivers available on the manufacturer's website.
    Also, try the other steps listed here: http://windows.microsoft.com/en-US/windows/help/no-sound-in-windows

  • I get the message at startup

    I get the startup message that I got my motherboard replacement for my laptop since 2 months ago

    product is HP Pavilion

    Model DV3-2360ee

    warranty: 1y1y0y

    series: CND0012NVV

    Model: DV3-2360-ee

    jump your assistant with my this message, it's making me delay when openning this pc

    I get what exactly the message

    product information is invalid

    the following products information programmed into the system card is missing or invalid

    Serial number of product System board (00 a)

    Product number for the Board of Directors (00 a) system

    I'm finding your quick helpness

    Thanls

Maybe you are looking for

  • Why text inserts back on Keynote slide?

    With Keynote 6.6.1 with El Capitan 10.11.2.    Suddenly the text that I entered a slide is BACK.  IE SDRAWKCAB. I think I must have inadvertently clicked... but can't understand why it's happening. The text is back if NEW or CHANGED to another copied

  • Hi, dear friends

    I have string starts with #456 then some values and I want to delete #456 and using other valuesHow can I do?Thanks in advance

  • How to center the button on the pop-up screen

    Look at the picture, I've created a popup screen click the menu key and I have that transparent and make it mode full screen and I added four buttons vertically please, u can correct me how can I Center this button in the pop up screen. Here is my co

  • Select start_with - connect in XML document (it looks like a bug in 11.2 g)

    HelloI really have no idea of what is the difference between these two cases and why one does not return anything. I have an xml document: <?xml version="1.0" encoding="UTF-8" standalone="yes"?><dirObjects>     <DIR_OBJECT>         <ABSOLUTE_PATH>/ho

  • Why my animations do not disappear when exporting to video?

    HelloTotal newbie question. Startin learn Adobe animate. I want to create simple videos animated for Facebook. I thought that I would use Adobe animate to it to create the animation and then export to mp4 or mov. I did managed to make an animation, t