The most convenient airport or TimeCapsule blocks google search

Similar Questions

• The most convenient airport in Bridge mode lose packets

  Hi all.

  I have an airport extreme with the version of firmware 7.7.7 (later at the time of this announcement). My modem ISP settings are blocked and it is already fixed to make routing/DHCP/Nat, so I use my airport extreme in Bridge mode to avoid the double NAT (it connects connects to the ISP with DHCP router).

  Both the ISP modem/router and Airport extreme are creating two different 'wifi networks", which belong to the same network (192.168.0.0).

  I can enter each of this Wifi network, obtain an IP address in both cases and start using the internet.

  However, when I use it on my ISP router, everything works perfectly, however, when I use it on the airport network, it fails from time to time.

  If I start ping an external IP address (e.g.: 8.8.8.8), I've never lost a packet on the network of the ISP router, but I lose packets often on the airport extreme network.

  Also, if I ping the ISP of the airport extreme network router I lose packets from time to time. Sometimes also vice versa. I never lose packets when ping the router whose network providing I'm connected to.

  All the settings on the airport extreme values by default (except that I created an additional network of 5 GHz).

  Can you give us some advice as how to solve the problem? I read somewhere that disable ipv6 connection sharing could solve the problem, but it didn't. Thanks in advance

  If you have the Ethernet cable from your ISP router that is connected to the "O" on the AirPort Extreme WAN port, unplug the cable and plug it into one of the three ports LAN <>- on the airport to see if this will help with the issue.

  However, if you have the Ethernet cable from the ISP router already connected to one of the LAN <>- port on the AirPort Extreme, then you'll need to reset the AirPort Extreme back to default settings and then set up again.

  If you have any further questions, the Airport extreme is defective and must be replaced.

• The most convenient airport and Arris CM820 modem drop connection

  I have Airport Extreme 6 Gen and a few months back from a 'new' Arris CM820 Time Warner Cable modem. Since then, I did have slowly and dropped connection problems a day - mostly in the evening so that streaming on Apple TV and Roku, and navigation devices on the MacBook Air and iPads at the same time. Each time, I do unplug it, wait 30 seconds and plug back in and it's good for a while. But it happens almost every day. I have been emailing and talking by phone with a representative from Apple support for a few weeks (had a record of the case), then she disappeared on me. I've updated firmware (v 7.7.7). Have also tried using a 5 G network as an alternative - but there is no help. Anyone else having these issues with the 'new' modems THAT TWC sends?

  If you have already tested the modem, try to choose a time when you can turn off the AirPort router and connect your Mac directly to the modem for a day or two to try things like that.

  Alternatively, you can of course call TWC support and have them check the line and the modem, but you already know that they will say that "things seem good to here" and that "the problem must be another device, like your router. .. even though things worked very well before receiving the 'new' modem.

  If the MacBook Air listed in your slogan is the only Mac you have, then you will need a lightning Apple Ethernet adapter to perform this test.   Maid in Gigabit Ethernet Adapter - Apple

  If connection problems continue when you have the Mac connected directly to the modem, the modem would then become a strong suspect.  This is possible.  But, it is also possible that the connection remains stable throughout your test... and if it's the result, TWC has strong arguments to say that their service and the modem are working well.

  Until then, you really don't know if you have a modem problem, a problem of the airport, or as can sometimes be the case... a modem - router compatibility issue. In such cases, the modem out OK and airport does as well, and each manufacturer blames the other for the problem.

  Please post on your 'test' results in the next few days.

• The most convenient airport wireless

  Can I connect my Airport express to my N450 netgear modem/router combo? And if I can then what are the benefits to do? Or it would be useless to do so?

  The AirPort Express can connect to the Netgear modem/router using either a permanent wired Ethernet cable connection... or... the AirPort Express can connect to the Netgear with only a wireless connection.

  How the Express connects determines what he can or not do.

  Which method of connection you thought?

  We assume that you have a Mac with the help of a current or recent operating system and also what you are asking about the current version of the AirPort Express, which has two Ethernet ports on the device.

• the most convenient airport

  my airport does not

  Is what model?

  What are the symptoms?

  You have it powered off and on again?

  Have you turned on and on the whole of the network?

• The most convenient airport and T-Mobile ZTE Falcon Z - 917 hotspot

  Hello

  Have my Time Capsule airport set up for my home network and connects to the Internet via WiFi (WiFi Mojave) antenna Service.

  I would like to connect my network to a T-Mobile Hotspot for a faster speed.

  Anyone know how I can do this via the AirPort Utility please?

  A time Capsule WiFi AirPort can connect to a WiFi Hotspot?

  Thanks much for any help you can give.

  David

  A time Capsule WiFi AirPort can connect to a WiFi Hotspot?

  Yes, if the hotspot provides an Ethernet port for a wired connection... Since the Capsule must be connected to another router or a modem with a connection permanent Ethernet cable, fixed.

  If the hotspot does not offer an Ethernet cable... it would be awkward, but it would probably work. Add an AirPort Express to 'join' the wireless hotspot, then connect an Ethernet cable to the Ethernet port LAN Express on the WAN on the Time Capsule port and set up time Capsule to create a wireless network.

  If you decide to try this, make sure that you understand the political s store back before buying the AirPort Express... in case things do not work.

• Not the most convenient airport

  I tried to change my user and the airport of "works" password. Airport utility shows green Internet but shows no airport. I tried all the fixes and made sure everything was up to date. When I reset and tried to start over, he's not asking for my settings as it did when it was new. I connected an ethernet cable from the airport to my laptop, it works on my other computers but not my printers. The green light is on the airport, and sometimes I have a yellow triangle in the utility. Is there a file for every thing. Any ideas?

  "When I reset and tried to start again it does not ask for my settings as it did when it was new."

  If you perform the reset correctly, the product then displays default settings... just as it did when you took it first out of the box.

  A real reset default is a bit tricky for some users.

  Turning off the airport by pulling on the power cord to the back of the unit.

  Wait 10 to 15 seconds

  Press and hold to reset first... and hold in for another 7 to 8 seconds while simultaneously you plug the power in the airport

  After 7 to 8 seconds, release the reset button

  Allow a minute for the airport back on the way to a slow, flashing amber light status

• Installed the Duck Duck Go module but disabled google search still by default?

  I installed the duck duck go light and Duck Duck Go SSL module and have also disabled integrated Google module. However, when I type in an item to search for and click the return/enter on the keyboard I always get sent to the Google search page, and not a Duck Duck Go Search, which is what I was looking for. Is there anyway to make sure my lack of research on the search engine requested from the keyboard rather than having to click the menu drop-down option that appears?

  If you are looking in the address bar, you can change the search engine by default:

  1. Typing in Subject: config.
  2. By clicking on the "I'll be careful, I promise!" button in the warning that appears.
  3. If you type "browser.search.defaultenginename" into the search at the top of the page box.
  4. By double-clicking on the stated preference and change the value "DuckDuckGo."

• Please tell me how to restore the regular installation of address bar of google search?

  I used to be able to search in my address bar and get regular google, but now I've updated firefox to a new version, she's looking for the address bar with foxstart which, although seems to have the google logo, does not all the results that google and does give me not the option of images etc which is very frustrating and tedious and after that I'm wrong looked in the address bar and got a load results fruitless search, I have to click on the button of my house and then redo the search all over google. It's just an irritating gripe. Please help me

  To set the default search engine used in the address bar, replace the value of the keyword. URL in Subject: config to one of the values in the search of the address bar with MozillaZine.

  • Search Google (Google search results page)
    http://www.Google.com/search?ie=UTF-8 & oe = UTF-8 & q =
  1. type about: config in the location (in a new tab) toolbar
  2. If the nonsense of warning message appears uncheck the box before dismiss the dialog box message
  3. filter by keyword
  4. Right click on the key word . URL and choose 'Edit' then paste in the string of search engine Google of your choice.

• Freezes the opening of links to apps or google search

  iPhone 6 s more. iOS 9.2.1.

  I have problems trying to open links to whatsapp, mails, etc. Also when you search thrhough google search, it freezes the app...

  I've seen similar behavior on 9.2.1 and forum ipad 2

  Re: URL does not work in Safari or mail after iOS 9.2.1

  "Same question here, but with a 6s iPhone more / 9.2.1."

  I tried everything, (cache, reset, reset network, suggestions of safari, etc.). Finally, the only thing that worked was to return to the initial configuration, removing everything and reworked links!. When I restored the backup it fails. I lose a lot if I start with the factory settings.

  I've restored the backup and waiting for the next update to Apple to fix this.

  If someone fix it please...! »

  Same problem here. I've tried absolutely everything. Even from the iphone as a 'new '. Nothing has worked. I spoke with the apple care team and the only solution was to Exchange my iphone because it is still under warranty. Of course, I don't want to be without a phone for one or two weeks due to which is clearly a software bug (even if not recognized by apple).  Seriosuly, very disappointing...

• The most extreme airport in roaming network.

  I should create a WiFi for 50 people. Simultaneous connections number supports both the airport extreme, roving networked?

  Specifications for Apple AirPort Extreme for say 50 users for each AirPort Extreme, so with 2 airports, it would be total 100 users.

  http://www.Apple.com/Airport-extreme/specs/

  Things would be really slow with 100 users, but 50 users should be OK with 2 airports.

• The most recent airport TC is compatible with all other routers?

  I have a relatively complex setup, in which case I have 2 TP-Link routers & outdoor CPE of TP-Link covering an acre & two buildings.  You want to have the capabilities of backup for my new MacBook.  The discussions I've seen so far are either old or do not seem to solve the problem...  Ideally, I replace the main router with TC and run ethernet to SCE in open air that feeds on 2nd router for the 2nd building.

  Routers are routers, and it is usually not much matter if they are wired... It is only when you use wireless configuration that things get complicated.

  A lot depends on how your existing two routers are connected... both should not be in router mode...

  There is no reason why you can not try to replace the main router with TC... test and see...

  If you experience problems after the exact problems... but first you need to know this modem and high-speed type are you?

• The settings DHCP Airport extreme &amp; NAT - cannot change default of NAT IPs?

  Hello

  I'm trying to configure Airport extreme, the most convenient to use for our office.

  Our Office IP is 10.255.x.x

  When I'm trying to Setup DHCP and NAT, in NAT options, there is only 10.0.x.x, 172.16.x.x and 192.168.x.x

  How can I get NAT to have 10.255.x.x?

  Without the NAT settings, I can not get this Airport Extreme to assign valid IP addresses and so unnecessary

  Sorry, but Apple will only accept the 10.0.x.x addresses to be assigned by the AirPort Extreme.

• After the update, pressing enter didn't work more to go to a URL, nor does in the Google search bar thing.

  Pretty much what is said. I've updated to the latest Firefox, and now this really irritating thing happens... There are also a lot of places. Specific things:

  • By clicking on the address bar of all, does not bring the thing little cursor flashing and gives me generally no indication that I actually clicked on the URL. Even with this small google search thing in the upper right corner.
  • More frustrating, when I press on enter after putting in a URL, it will not even go to the site.
  • After having upset both of those things, I try to type something on a Web site, and although the URL is immutable, it starts to fall a lot of suggestions from my story.
  • Finally, when I'm doing my crosswords on the Washington Post, and I switch to a different tab to type something on there, it is not pass my typing thing - it remains on the crossword, typing things into that, rather than in the input field, I clicked on start typing in.

  So, Yes, it's very embarrassing, and I'd be delighted for all the help for these issues...

  I look at the FAQ and they said something about the thing AVG SafeSearch, causing one of my problems, but I do not have this extension, this certainly isn't that!

  You encounter this bug that will be fixed in Firefox 10.0.1, eventually published later this week.

  • bug 718939 - Java applet causes fields to become semi-don't text not responding

• Why FF spends CPU both on google search results?

  I have the problem that Firefox spends more than 10% of CPU on the display of a static page like google search results. I use Firefox on a late 2012, MacBook Pro and the constant use of the CPU so drains the battery and produces a lot of heat after some time.

  Steps to reproduce:
  1. start Firefox in safe mode, disable all extensions
  2. Enter "why ff is spending cpu both on google search results ' in the address bar
  3. watch how the Firefox CPU usage goes to a constant 10%

  Additional information:
  It seems that other users have experienced the same problem too, for example,
  https://support.Mozilla.org/en-us/questions/954376

  https://support.Mozilla.org/en-us/questions/960806

  https://support.Mozilla.org/en-us/questions/957512

  However, the systematic response to questions was always restart Firefox in safe mode, disable all plugins, etc, etc. I tried everything, nothing works.

  Workaround solution:
  For me, the problem occurs only on the page of google search results. I don't know what is special about this particular Web page and show why he needs so much CPU. It may be that Firefox uses a lot of CPU on others too many static Web pages. However, a simple cure for my problems (for now) is to move to some other site when Firefox is idle. CPU utilization drops at least < 1% almost immediately after that.

  Hi klopps, I don't get on Windows 7 (screen shot attached; tried both connected and disconnected).

  Google sometimes run experiments on its poster page causing people to have results different and/or a different behavior. Disconnect and clear all cookies from Google can give you a default experience, or maybe not, they don't advertise these things.

  If you want to try it:

  Just a page on the site, either:

  • Right click and select View Page Info > Security > "View Cookies".
  • Menu Tools > Page Info > Security > "View Cookies".

  In the dialog box that opens, you can delete all Google cookies individually.

  Then when you reload, bypass the cache of Firefox using the command + shift + r.

  Regarding the 3 wires you linked, it seems that everyone has a unique number. It doesn't seem to be a single explanation that applies to each of them.