The PXI-2510 module for 2013 has different names

Similar Questions

• Would it not correct to say that the PCI-6110 can be set to 'redeclenchables' but the PXI-6115 module cannot use this property?

  Would it not correct to say that the PCI-6110 can be set to 'redeclenchables' but the PXI-6115 module cannot use this property?  If Yes, where is it documented the series cards can do trigger?  For example, is it possible to configure the trigger on the PXI-6124?

  Hi Joel_Neptune,

  The PCI-6110 and other materials as the PXI-6115 S series and SMU-6124 do not natively support NOR-DAQmx analog input alarm. However, you can use one of the generalist counters/timers of the Council to generate a reenclenchees pulse train, then use this as the sample clock pulse train. This transportation example shows how:

  LabVIEW\examples\DAQmx\Synchronization\Multi-Function.llb\Multi-Function-Ctr Retrigg Pulse Train generation for the Clock.vi sample

  In addition, the new material of the simultaneous sampling X series are supported trigger analog input without using a separate task of counters/timers.

  Brad

• Variation of thermal EMF of the PXI-2530 modules

  This message/question is a companion of my the most recent message in another thread.

  In addition to watching some resistance higher than expected that affected current measurements using modules PXI-2530 multiplexer 4W topology, I saw systematic variation in track-to-track blood pressure measurements. Tensions would increase gradually through the 16 channels in a configuration by measuring the voltage at the terminals a resistor 1.5 kOhm with 0.5 au crossing (75 uV). I've identified that the thermal EMF of the reed in the PXI2530 module switches is on the same order of magnitude of these measures and set out to quantify the differences EMF thermal track-to-track between my three modules.

  Test method: I have a TB-50 which is configured to mux the signals of tension for a DMM. I connected each of the four DB-50 one cable of 176 pins to this block and collected with a PXI-4071 pressure readings set to 7.5 digits precision in the range of 100 mV and > 10 GOhm impedance. For most channels, it took several minutes for the voltage stabilize - or at least appear that it was to stabilize.

  I enclose three graphs. Note that the vertical scale is the same on each.

  Data that triggered this survey was collected with MUX1, via connector P2 to voltage. The magnitude was not quite the same-probably related to the phenomenon of stabilization time, but obviously the worst group of channels three multiplexer modules.

  The three modules were all bought at the same time (about 2 years ago), but had only limited its use in the first year or more. The three now have various 'mileage' based on my use. But MUX1 clearly behaves differently two other modules. The

  I changed my test conditions to spend 0.5 au via a higher resistance to thermal EMF less important. The PXI-2530 sheets indicate that thermal EMF must be less than 50 uV. In most of my measurements, it is. But not for MUX1!

  Any thoughts?

  Thank you

  Jeff

  Hi Jeff,

  You can check that all the three modules are PXI-2530, not PXI-2530 b (while, as the PXI-2530 b parts slightly higher thermal emf)?

  Specification of emf thermal 50uV of the PXI-2530 is a typical value, is not a guarantee of spec.  See a few channels higher than the spec is not a cause for alarm, but it shows that we must take account of this in our measurement error.  Note that the industry standard for the technical measure thermal emf is to close the relay, wait a few minutes and then take a measure of tension.  For example, if you scan through a switch faster than a relay per minute or so, the thermal emf will be less predictable and stable.  A single module performs worse at these low voltages is not indicative that this module is a failure, etc. the module is fine.  Unfortunately, the reed relays have more emf thermal relay of the armature, mainly because of the many layers of metal in a Reed compared to a frame (each metal junction is a source of emf if these metals are not the same).

  Thermal EMF is proportional to the temperature, it may be interesting to note the position of the chassis of the less powerful module.  Placing hottest modules (scanners, Ara, RF, etc.) will reduce the thermal emf.

• blue screen on the PXI-8106 module: hardware malfunction

  Hi all

  I have a module, PXI-8106 (2 GB of RAM) - with a PXI-6254 and I was running trials with the attached screw (continuous acquisition of 16 I and 32 DI triggered by RTSI 4-5 kHz).

  When I started this morning, I got a blue screen of death saying this:

  Hardware malfunction

  Call your provider of support material

  NMI: Parity parity CheckMemory error

  The system stopped *.

  Now, I restarted the PXI revived the VI and it works again.

  Is there something I can do to ensure that this error will not be shown again?

  Thanks in advance for any help

  Meh... I know I'll be back on a fairly old post, but I found the solution.

  For some reason any installation Vision Acquisition software 8.5.1 created the problem by defining itself as the default driver for the network card. Then, go to 'manage' by right clicking on the 'Bureau', go to the hardware section, network card and select the intel driver solved the problem.

• Is it possible to add the MiniPCI WLAN Module for Satellite Pro 4300?

  Hello

  I got a 4300 Satellite Pro and I want to add a WLAN MiniPCI Module. Is this possible and is someone able to provide details where to add this module for example some technical documentation in images.

  Greetings
  Florian

  Robin is right about the upgrade. It is not possible. in my opinion the best solution for you is to use a PCMCIA WLAN card.

• I get the following message and the crash - "container plugin for firefox has stopped working". How can I fix?

  On the last day of little the interent has been crashing with the following response - "container plugin for firefox has stopped working." Why and how can I solve this problem?

  
  

• Using the SCXI-1520 module for measurement of torque

  Hello

  I'm working on a project that requires a measument couple in real time on a speed-shaft drivetrain configuration phase.

  I have the SCXI-1520 module, and I think with a with a configuration of full-bridge strain gauge to do this.

  The problem is that it is not possible to connect to a real-time measurement, so my first solution was using some sort of wireless transmission to receive data in the SCXI-1520 module

  The Arduino + Xbee seems to be the best way to go, but at the same time, I think I might have a few problems of conditioning of the signal while transmitting data to LabVIEW through the SCXI-1520.

  Don't you think it's the best way to do it, or is there a better solution?

  Thank you!

  Hi Kenny,

  What type of operating system are you using? When you say 'Real time', do you mean look at a signal when it occurs? If you use communication networks, you will not be able to get truly control in real-time because communication networks is not deterministic, and you cannot guarantee the synchronization.

  If you try to get a signal and he discovers that you buy it, you should be able to use the Arduino and LIFA with LabVIEW. Adding the SCXI-1520 will not add any additional resolution in this circumstance.

  Best regards

  Anna L

• How to automate the installation of modules for outs big roll?

  I asked this question a while ago here:
  https://support.Mozilla.org/en-us/questions/884702

  This response worked well up to version 21. Now when I follow these steps, the add-on does not install.

  Reminder, I do deployments on a large scale of Firefox, and I would like to be able to configure a group of modules that will install automatically (I don't want to manually install each).

  How can I do this?

  Thank you!

  Hello brundleflyguy, not much has changed - however the files should now go to \browser\extensions in the program folder. some information on the issue are explained in www.ghacks.net/2013/05/15/why-you-may-have-lost-access-to-plugins-or-extensions-in-firefox-21/.

• How to download the labview embedded module for arm microcontrolller organization software?

  you will need to download the evaluation software for labview embedded for arm microcontroller module...

  Hi ROUDDLY,

  See here and here

• The Adobe Story app for iOS has been interrupted?

  I can't find it in the app store from my iPhone. I followed a former Web link to him and he said that it is not available in the United States and others can always it access? What gives?

  Connection to the iTunes Store.

  Yes, it has been removed from the App Store.

• Name of the Workstation 9 module for ethernet

  Hi, I have Vmware Workstation 9, running Centos 6.3 x 64.

  I wonder what is the name of the Ethernet module in 9 workstation?

  When I run lsmod I don't see a vmxnet or pcnet32

  Cat vmware - tools.conf

  install/sbin/modprobe - q - ignore-install vmxnet pcnet32; / sbin/modprobe-ignore-install $CMDLINE_OPTS pcnet32

  If anyone can tell me the name of the module to the ethernet card?

  Thank you.

  Do you mean what NIC is used inside the guest of CentOS?  The emulated NETWORK card could be one of many.

  I just created a CentOS 64-bit guest in the 9.0.1 Workstation and the emulated network card is the e1000 (as evidenced by the ethernet0.virtualDev = "e1000" line in the .vmx comments configuration file).

  According to this article, the e1000 is "...". An emulated version of the Intel 82545EM Gigabit Ethernet NIC. "( http://kb.vmware.com/kb/1001805 )

• How to set up the PFI lines as input to PXI-6713 module

  Hello

  I have 6713 PXI module in my chassis PXI-1044. I have configured the PXI-6713 module to geneate some analog signals to my Board of Directors.

  Council inturn process this analog signal and answers in return the status signals through a registry to the Board of Directors. In my application, the status bits in the register state of the governing body are mapped on the PFI 0:3 bits of the PXI-6713 (pins 11,10, 42 and 43) module.

  My query is how can I configuration lines PFI as 6713 PXI module entries to read these status bits?

  May be less than the explanation could give you little more information w.r.to my request.

  When I use NI USB - 6008 module to read the same bits, because this unit has 12 e / s digital, I was able able to read the status bits in the last 4 digital lines by setting up those digital lines as input.

  In the PXI-6713 module, I have only 8 digital lines. These 8 digital lines I used to send digital signals to the Board of Directors. I find myself with no digital i/o. Therefore, I could not use these digital lines. I'm left with only one option to use. Joana re PFI lines. Also the bits of status in the axis of the room are mapped such that the bits can be read through the PFI lines.

  I was wondering do we have any example code to use inorder to read these status bits to the Board of Directors using the PFI lines.

  Please let me know if you need more information to help out me.

  Thank you.

  Hello

  When using the PFI PIN as input, you can individually configure each PFI for edge detection or level and the selection of the polarity.  This information of PFI are referenced in the manual of Series DAQ Analog Output on page 6-1 (http://www.ni.com/pdf/manuals/370735e.pdf).  Unfortunately, the PXI-6713 PFI lines are able to time a signal input and output for functions, AO or counters/timers.  The ability to create static DI of the PFI lines is not available for the PXI-6713. However, some cards have this capability.  The latest National Instruments products with PFI lines have the option of setting as PFI lines:

  1. Static digital input
  2. Static digital output
  3. Input signal of sync for functions HAVE, AO, DI, or counters/timers
  4. Output signal of the calendar functions HAVE, AO, DI, or counters/timers
     (http://digital.ni.com/public.nsf/allkb/14F20D79C649F8CD86256FBE005C2BC4)

  When the static value such as DIO, PFI lines are assigned to a different port (for example. PFI0-7 is Port1).  More details on this subject can be referenced at:

  http://digital.NI.com/public.nsf/allkb/DA2D3CD0B8E8EE2A8625752F007596E1

  http://digital.NI.com/public.nsf/allkb/862567530005F09E8625677800577C27

• PXI-2510 has no reaction when using NI VeriStand

  Hi all

  I want to use a PXI-2510 in NI VeriStand and I read a document named NI VeriStand module - fault Insertion units OR to: http://zone.ni.com/devzone/cda/epd/p/id/6248

  After deployment, I change my state of the controls in the workspace, but PXI-2510 has no reaction.
   
  Here are my steps:

  1. download the file - 2510_add_on_nivs2011.zip

  2. copy the files in the folder named Custom Device llbs in \National Instruments\VeriStand peripheral 20xx\Custom

  copy files into the folder named models display in \National Instruments\VeriStand models 20xx\Display

  3. open NI VeriStand and use the PXI-2510 as a custom device.

  4 deploy and open the workspace. the default fault chains station is cross with channels of dut. but when I change its station in an open State, PXI-2510 has no reaction.

  Please help me with the problem.

  Best wishes.

  If you use the console Viewer (Tools-> display console), you see error messages published on the screen?

• What are the data for the PXI-6552-invalid range

  Hello

  Let say, I put the voltage custom for the PXI-6552 module

  2.4V - high level

  0.6V - low level

  Then, on canal0, I provide a signal of

  sample

  3V 0

  1 3V

  2 VOL. 2

  3-0V

  Thus, the sample 0.1 is high. Example 3 is Low.How sample 2? Please notify. Thanks in advance.

  Hi Engwei,

  Programmed tensions are the levels that you would have to exceed or down before a change of digital status is saved. This means that in your example, coming from a high level of 3V goes to 2V, the Analyzer signals would still record a strong logic. The deadband is actually a way to filter digital noise, common to the majority of the architecture of digital input.

  Best regards
  The Ilana Joshua
  Applications Engineer OR

• How can I display an analog input for the PXI-5105 on LabVIEW?

  Hi all

  I am very very new to LabVIEW and I started to tinker with it. I use the version of LabVIEW 2010 SP1 on Windows 7 OS. I also have the chassis NI SMU-1073 with SMU-6361 and PXI-5105 modules and the chassis is connected to my PC via PCI. I became familiar with the devices and trying to see some analog signals to one of the channels on the PXI-5105 module in a graph in LabVIEW.

  I would appreciate your help.

  Hello Henokview!

  I would like to read through these tutorials to understand the steps of programming of the NOR-SCOPE, NOR-DAQmx. After reading these links below, you will be able to understand how to connect the output of a readfunction to a chart or table.

  DAQmx

  http://www.NI.com/white-paper/5434/en

  OR-SCOPE

  http://www.NI.com/white-paper/3382/en

  Best regards

  Jonas