The Question Daqmx upgrade

Similar Questions

• The question processor upgrade

  OK so I have a Presario SR1920NX I upgraded to 2 GB of ram and put to update to windows 7 but here's the question... I currently have 2.2 GHx processor and I feel its not quite worth more so I decided to upgrade, but basically, each processor I looked for my pc requires an update of the Bios ok no biggie execpt theres no bios update for my pc running windows 7 so I would be nice to upgrade without bios or would I need to go back to xp update of the BIOS, and then reinstall windows 7?

  Here are the specifications of your desktop Compaq Presario SR1920NX. Previously, I had a Compaq SR1910NX and always use an HP a1632x, two use the same motherboard as your SR1920NX. My a1632x is a "Athlon 64 X 2 3800 + 2.0 GHz" which resembles your "Athlon 64 3500 + 2.2 GHz" except that he has two hearts. I upgraded to 4 GB of memory RAM and installed Windows 7 64-bit. The system works without a problem and partitions in the middle of the year of 5 years with a HP 512 MB HD6450 graphic card.

  Installation of 4 GB and a graphics card will help your system to feel faster and upgrade to a dual core Athlon 64 X 2 4800 + will help certainly... but the CPU is going to be hard to find and quite expensive, even on e - bay.

  BIOS version 3.11 is the last update of the BIOS and does not add processors higher than socket 939 X 2 4800 +. You will need to go back to XP to install the BIOS update, because it will not install on any other OS.

• WLC4402 - Questions to upgrade the AP and controller

  Hello

  I just upgraded an AIR-WLC4402-12-K9 to version 7.0.98.0 of the software, and I have a few questions-

  1. I have no APs to connect yet but when I do I'll have to check what software they run and perhaps demote the controller to get access up to v7 points?  To join the WLC v7 since v3.2 I had to make a few intermediate upgrades and I wonder if I have been a little premature and should have done updates after the APs have been associated, has new software pushed from the controller and then performed the steps in upgrade of WLC so the WLC and APs were synchronized in terms of software.

  2 - the memory usage is sitting at 60% with no associated APs.  I have just connected 4402-12 running 5.1.151.0 and he's sitting at 33% use of memory with associated access 11 points.  Have I spent in a too recent version for this controller?  What is a figure of the memory use of a 4402?

  Thanks in advance,

  Jason.

  Jason,

  A question.  You should be fine.  When the AP detects the WLC, it will do a code audit.  If this isn't the right code, it can extract the correct image of the WLC.  As long as the AP you are supported in 7.0, the recovery on the access point image won't matter.

  For question 2.  sounds of 60% of normal for 7.0, depending on the amount of memory is on the device itself.  I woulnd't ' t be too concerned about the memory usage until you points upward in the high 80 years.

  See you soon,.
  Steve

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Install Web Premium CS4 Student Edition on laptop after the Question upgrade Windows 7

  I hope that this has not been asked before, but my question is this: I want to upgrade my laptop Windows XP to Windows 7.  But I've heard that all programs be uninstalled after installing Windows 7 on a computer running Windows XP.  I have to reinstall all the programs again to use CS4 Web Premium.  But my student edition says that I can only install the program on two computers.  Does that mean I can install the program twice, or can I still install on the same laptop after changing the operating system (I installed CS4 on both computers, my computer, laptop and desktop)?  I want to continue using CS4 Web Premium on my laptop but I'm worried I won't be able to install it because I installed CS4 on my laptop and desktop (two installed already).  I would like to know if I can install on the same laptop after upgrading to Windows 7.  Thanks in advance for the help.

  WebMacro123

  The question isn't installation... it's activation. Disable the software first. (Help > deactivate from any application).

  Back up all your data, preferences, etc. because, as you note, it will be a clean install of Windows. Know that it is only cool method to upgrade a Windows installation. NEVER don't upgrade a Windows in place (or, IMO, Mac OSX).

  Bob

• Question on the recovery CD and the Vista anytime upgrade

  Hello

  I bought a toshiba laptop now a year ago, it came pre-installed with vista home premium.
  I would like to do a complete cleaning my system as its useless been lately and isn't a fact since I bought.

  It came only with - a the product recovery disc and upgrade Express windows.
  But I'm worried because if I do a recovery of product I don't have the real vista disk it SHOULD have and will not have vista on my laptop or one of the files that toshiba put on it.

  What should I do?
  What a product recovery disc actually have on it and do? What is the Windows anytime upgrade disc?

  I have been informed by microsoft and I.T. technicians everywhere that i should have a vista installation disc in the same area so the fact it came pre-installed.

  Help, please

  > It came only with - a the product recovery disc and upgrade Express windows.

  As you say you have the product recovery disc.
  This Toshiba drive contains the image of Toshiba.
  The image is a package and it contains the operating system Windows, Toshiba drivers, tools, utility and software further.

  The use of the recovery CD will fix the laptop back to the factory settings.
  So just boot from the recovery CD and follow the instructions on the screen.

  Just for info:
  The recovery CD will format the whole HARD drive, but I see that a backup is not important to you.

  See you soon

• Satellite P10: Question about the limits of upgrade of RAM and HARD drive

  What are the limits to upgrade my laptop Satellite P10? Currently, I use 1 GB of RAM (2 x 512) and I still have the original 60 GB 4200 RPM HARD drive. I'm mainly interested in upgrading my hard drive to at least get a 7200 RPM 100 GB disc. Better would be one of the ones 24 hours server as Hitachi HTE721010G9AT00, I have just turned off my computer. Which one to take and are there limits (BIOS) (keeping in mind that there will be 200 and even the 250 GB drives next year)?

  RAM: should I put two 200pin SO-DIMM 333 or 533 or should not change at all as it works very well and stabil now?

  Hello

  In my eyes you should follow the guidance of Toshiba line and must use the memory modules that are recommended in the user guide. But if you can also try to test with 400 Mhz or 533 Mhz. I think that each dealer notebook or memory could do that.

  I think the BIOS might be able to handle the hard drive with capacity of 30 GB / 40 GB / 60 GB / 80 GB, Bus Master IDE with ultra DMA 100 synchronous
  In my opinion the BIOS does not recognize the larger HARD drive.

• Satellite P100-429: Question about upgrading the processor

  When I bought this model 6 months ago I got this one with just a T5500 1.66 GHz but since then Intel reduced prices 40% it is me the upgrade option.

  Someone at - any idea how I can update, the following list lists the T7600 @ 2.33 GHz compatible on the Bus speed and execution step by step. The only difference being the memory cache L2, 4MB compared to my old one of the 2 MB that will have an effect.

  http://i82.Photobucket.com/albums/J249/swoggy/cpuspec.jpg

  Thanks for anyones help.

  Hello

  Upgrading the CPU is a bit tricky on laptops and more often than not desirable and is not possible.
  After the CPU overheating upgrade, it would be possible that don t cooling modules are working properly and the laptop.
  Why? Well well, the CPU new and stronger products, more heat and the temperature would be Monte. The fan table that is stored in the BIOS will not correspond with the new CPU and the cooling fans would not correctly work.
  In addition, upgrading CPU will void your warranty! It's very risky!

  Anyway, looks like you certainly want to upgrade the processor?
  So I would check the chipset installed on your laptop.
  Try to know the details of the chipset and Intel page for compatible processors research!

  concerning

• Upgrade of log Insight in paragraph 3.3.1 of the questions!

  I do some tests on the 3.0 upgrade procedure in paragraph 3.3.1. When I connect to the IP address of the master node and import the file pak after a while he said that the upgrade is successful and to display the State of the cluster. I click on the State of the cluster and see that the second node is now the upgrade... After a few minutes, the web page of administration for the master node is now insensitive!  When I connect to the third node and look at the State of the cluster, all nodes are showing version 3.0 and the connected state, it seems that the upgrade is blocked or something!

  I have now solved this problem in 3.3.1.  There is a new version of JAVA in 3.3.1 (jre1.8.0_71), who knows nothing about the previously configured cacerts keystore.

  Resolution (on each Cluster node)

  1. CD /usr/java/jre1.8.0_71/lib/security/
  2. .. /.. / bin/keytool-import - alias loginsight-/home/cacert.crt - keystore cacerts file file
  3. Restart the loginsight service
  4. Double-check this transmission of events will now be stable!

• iPhone 6 more issues of button "home" and turn off the questions

  I have two separate issues with my iPhone 6 more

  9.3.2 software (updated to try to solve this problem - question began before the software upgrade)

  My iPhone only more 6 works randomly.  I'm still able to make calls and use the phone, but the phone is constantly interrupted by these two questions.

  "Slide to turn off" or button 'Cancel' at the bottom

  (1) the phone asks me to "Slide to Power Off" - at the top of the button slide phone - with a cancel downstairs.  Slide and turn it back on does NOT resolve this problem.

  "Home" button is to take a screenshot of my current screen randomly.

  (2) when you press the button of my house, he takes a picture of my current screen instead of Act works as a home screen button.  This can happen 1 time or 10 times in a row before the home button functions correctly.

  Here is a screenshot of the camera to illustrate various photos taken.

  

  I did all the updates

  I did tap hard downs

  I backed up my phone and tried to reset to factory settings

  These are the questions randomly but are very common - a question of these two issues with caused during the use of the phone to navigate or "Slide to power off" appears randomly if the phone is not in use.

  Please help with any suggestions!

  Your sleep/wake button is pressed somehow. You have a form any case suitable for your phone that covers this button? If not, the sensor that presses the Sleep/Wake button against is missed ignition. As you even tried a factory restore, it may be clear that the problem occurs because of a case that is pressing the button somehow or the switch has gone bad.

• HP TouchSmart 300-1120: the video card upgrade

  I came into possession of a HP Touchsmart 300-1120. I do not use not for the games just the navigation and use to watch movies when traveling through Plex home theater.

  I've updated the CPU to an Athlon X 4 605th & maxed out the RAM 8 GB. I noticed that I can upgrade the video card using the Mobile PCI Express Module slot.  Even though I know that the GPU Radeon HD 3200 onboard can handle HD videos, he hangs out considerably. even though I have the film on the hard drive.

  So the question is, where can find one of these cards. And is there a way to upgrade the PSU?

  Thank you

  Jim Hutto
  I do not work for HP.
  I am a computer technician and a passion for computing with more than 32 years of computer repair and networking experience

  Your PC AIO has a sleeve of MXM graphics.  The following video card will work. It was included in some models of PC.

  HP 594505-001 nVidia GeForce G210 512 MB MXM DDR3 video card

  http://PartSurfer.HP.com/ShowPhoto.aspx?PartNumber=594505-001

  You need to search online to find a seller or a person who has one for sale. I see them on eBay for @ $35-50, 00

  The upgrade of the PSU is not a viable option.

• Equium A100 - 02L: Question about upgrade memory to 4 GB

  Hello.

  The time has come to upgrade my laptop, but I don't know how to get the full 4 GB of RAM in it.

  Toshibas page for this computer says I have 4 GB, but also that its two memory locations only consist with maximum 1024 MB card. Is the only feasible supplement by vista ready boost or something?

  The vehicle currently has two 512 MB 667 mhz pc5300' cards inside.

  Please help me... I am looking to order these items very soon and I don't want to buy something that does not work.

  Thanks in advance.

  I found the info you can increase the RAM to 4 GB. You have to buy 2 X 2 GB RAM modules.
  So now the question is what OS you use, because 32-bit Vista recognize 3 GB only.
  Just for info: http://aps2.toshiba-tro.de/kb0/TSB82022E0000R01.htm

  All that s!

• Question about upgrading RAM on Satellite U400-138

  Hello

  My laptop model is Satellite U400-138, part number: PSU44E-00500JG3

  Technology:
  type: technology Intel Centrino 2 processor on processor Intel Core 2 Duo P8400, Intel GM45 Express chipset and Intel WiFi Link 5100
  Clock speed: 2.26 GHz
  Front Side Bus: 1066 MHz
  level 2: 3 MB cache

  Operating system:
  Genuine Windows Vista Edition Home Premium (pre-installed, Toshiba-HDD recovery)

  System memory:
  standard: 3 072 (2 048 + 1 024) MB
  maximum extension: 8 192 MB
  technology: DDR2 RAM (800 MHz)

  In intel webside one writes the following on my motherboard laptop specifications:

  "1.2 Intel GM45 Express Chipset supported feature
  All features supported by the Intel PM45 Express Chipset supported by Intel GM45
  Express Chipset unless otherwise stated below. Additional features are listed below. "

  1.2.2 memory system «»
  -Support to 667 MHz DDR3 then FSB 667 MHz isn't that. "

  "1.1 Intel PM45 Express Chipset supported feature
  1.1.2 storage system
  -Support for DDR2 and DDR3 SDRAM
  -Support for DDR2 667 MHz and 800 MHz
  -667, 800, and 1066 MHz DDR3 support
  -One SO-DIMM connector (or memory) per channel
  -Channel memory supported two Configurations
  -Double-channel symmetrical (with Interleaved access)
  -Dual-channel asymmetrical (with or without Intel Flex memory technology)
  -Support for 8 GB of maximum memory
  -scale 64 - bit per channel
  -Technologies of 256 MB, 512 MB, 1 GB and 2 GB memory supported
  -Support for DDR2 and DDR3, x 8 and x 16 devices
  -Support for DDR2/DDR3 termination on chip (ODT)
  -Supported partial written memory using data signals mask (DM)
  -No support for chip quick selection mode
  -No support for ECC
  -No support for operation 1N. "

  http://www.Intel.com/assets/PDF/datasheet/320122.PDF

  The question is...

  I want to upgrade my portable computer system memory 3 GB DDR2 (800 MHz) RAM to 4 GB of RAM DDR3 (1066 MHz), which is compatible or not?

  Respect,
  enteoana

  Hello

  In my opinion, you should follow specification not Intel and Toshiba. S Toshiba of info is based on own tests and facts.
  So, depending on the specifications of Toshiba for the GM45 Chipset it is clearly written:

  Min(on Board) wheel capacity - DDR2 800 MHz 0 MB / 8 GB max
  Type of extension of memory - DDR2 800 MHz 1 GB/2 GB/4 GB
  Type of module - SO-DIMM

  So if Toshiba write about 800 MHz modules, you must use the modules to them and not faster.
  You may be able to use faster too, but they do not work with the maximum speed, but not going down to 800 MHz.

  If you want to use max RAM amount use recommended and tested 2 x 2 Go DDR2-800 (PA3669U-1M2G).
  Indicated as compatible RAM, 4 GB DDR2-800 (PA3670U-1M4G).

• Satellite A300-247 - cannot register for the Windows 7 upgrade

  Hi all

  I have the problem by registering for free Windows 7 Upgrade.

  I have a Toshiba Satellite A300-247 and in their registration require the number of room and the j) not it is only numbered series. I bought the laptop in Israel. Is someone know what to do thank you to useful... Lars_3 thank you very much you the answer.

  Logo of the model is still off I wanted to say thank you, there are problems in the site of the browser servers think so much

  Hello!

  To be honest it's a little hard to understand your question.

  What exactly is your problem? I think you want to register on the site to upgrade to Windows 7.
  I n t have experience with this because I didn t buy such a phone compatible update yet, but I think that you need the serial number and the model number of the laptop. The two pieces of information you can find on the underside of the laptop.

  Don t forget that this upgrade option is available for laptop purchased from June 26, 2009 to January 31, 2010.

  Good bye

• Satellite A200-1CR: Question about upgrade HARD drive

  Hi all...
  I would like to ask something...

  I have toshiba Satellite A200-1cr with 120 GB HARD drive...

  I would like to change my HARD drive. I found a disk hard 2.5 "with 250 GB.

  My questions are the following:

  (1) my knowledge of the workstations are very very good. Is it easy to change myself?
  I guess it is, but I want to be sure... I guess that is on IDE, right? No SATA at all?

  (2) if I changed it I lose my warranty?

  (3) can I give my laptop Toshiba in Greece official store and let them make the change?
  May I take in an informal shop, too?

  (4) can be put on the laptop 2 x 250 GB such US new computers laptops from toshiba?
  Is there enough space in the laptop for such a change?

  Thank you in advance...

  Hey Buddy

  It is good that ask you the question.

  (1) the Satellite A200-1CR supports SATA and no IDE interface and that's why you need a SATA HDD. It of really not difficult to replace the HARD drive and as far as I know, you should find a few details in the user manual. There is a useful statement and photos that explain the entire procedure.

  (2) hm AFAIK the drive replacement HARD will not void the warranty, and has no effect on the State of security.

  (3) you can also contact the maintainer authorized Toshiba in your country for a HARD drive replacement, but in my opinion that is not really necessary because the replacement is not very sensitive. As I said above, check the user manual.

  (4) I don t think that your laptop will support 2 x 250 GB HARD drive.
  Of course, there are a few other series laptops which are abele to support two hard drives but I n t think that your laptop A200 support.

  Just a small comment on the new HARD drive:
  The fact is that some more HARD drive are not supported by the BIOS. I mean an upgrade to 120 GB to 250 GB drive HARD is really a leap one possibly your BIOS would not recognize the HARD drive correctly.
  So I recommend to test the HDD first before buying.

  Good bye

• Change the sample DAQmx and Terminal configuration mode

  Hello

  I'm studying 'Timing and synchronization features of NOR-DAQmx' from the following link,.

  http://zone.NI.com/DevZone/CDA/tut/p/ID/4322

  Could someone tell me how to Figure 2, Terminal configuration entry in the part "DAQmx virtual channel creat? Shoud I double-click on the icon to change it? Or there is some way that I can show it in the block as the sample mode diagram in the DAQmx part?

  How can another question, in the DAQmx calendar part, I put "Continous Samples" here? It comes from the function palette? Thank you.

  Hi Oly,
  To make the configuration of senior year to enter the channel 'DAQmx create' you will need to create a constant or control over this VI either.  When you hover over a VI, as the VI "DAQmx Create Channel", you will notice that the dots appear around the edge of the square.  "" When you roll your mouse over these points, you mouse pointer will appear a coil of cable/wire how you can right click your mouse and select 'Create' constant ' or 'create' control '.  If you create a control, you have a user control in your front, where as if you create a constant, you will have a drop-down list in your block diagram.
   
  It goes the same for continuous samples, simply hover over the VI, right-click on the corresponding 'point' and select this option to create a constant.
   
  In case my instructions are unclear, that I have attached pictures of how to go about doing this, the first is to show 'points' I speak around the VI and the second picture shows the possibility to choose after you right-click on the point.
   
  Good programming!
  aNIta B
  Technical sales engineer
  National Instruments