The RAID on the PowerEdge T610 controller upgrade

This system came with a SAS6/iR controller and after the installation of Server R2 2012 and with 32 GB of RAM it's on all fours, probably because we use software RAID 5. I want to upgrade RAID controller so that I can use hardware RAID 5. What controllers are compatible with the T610? I know that the H710 is eligible, but what about the H710P and the H810? We have a bottom of basket that holds 8 discs. Do we need anything else? I see that some people needed cables as well.

PERC 6 / i and the H700 are validated for the T610. The Hx10 are 12 generation servers (like T620, T610 is 11G). H8x0 controllers are for external storage.

Main differences between H700 or PERC 6:

PERC 6 is 3Gbps, max disk 2 TB, 256 MB cache
PERC H700 is cache cache/memory NVRAM 6Gpbs, TB + 2 disks, 512 MB or 1 GB

Tags: Dell Servers

Similar Questions

  • Dell PowerEdge T610 (memory upgrade)

    I bought Dell 16 GB certified replacement Memory Module for select Dell - 2Rx4 1333 MHz RDIMMS LV systems

    Currently, I have 8 GB of RAM (1 GB on every slot machines). After I installed this new memory and restart the server, it shows invalid memory configuration. So, I changed the memory setting in BIOS 'Advanced ECC' to 'optimize memory '. But it detects more than my current speed of the memory is 8 GB. Is there something wrong with the configuration of the memory? I tried to re - establish the new RAM.

    Help, please. Thank you.

    Hello.

    Your memory configuration is not valid because the channel memory CH0, is not balanced with channels CH1 & CH2. Refer to the schematic illustration below:

    In order to balance the memory on these channels, we should have memory DIMM in:

    A1, A2 & A3 = B1, B2 & B3 in addition also A4, A5 & A6 is B4, B5 & B6. That's why CH0, CH1 & CH2 memory modules must be identical for the performance and optimal memory configuration. Depending on the upgrade amount of memory you are looking for, you can buy 1 more 16 GB DIMMS and then fill in slots A1 B1 & offer a total capacity of 32 GB. This will provide more flexibility for future memory upgrade

    Let me know if you have any other questions.

  • The PERC S300 controller replacement

    I want to upgrade a server PowerEdge R310 Windows Server 2008 R2 to R2 2012. Unfortunately the PERC S300 is not supported and I could not find the necessary drivers.

    I found that PERC H700 has the correct drivers and is compatible with the R310, can anyone confirm that please?

    Are there cheaper alternatives? Otherwise, I think I have to disconnect the PERC controller and connect the drives to the internal SATA ports, but then I have 4 independent drives with no RAID either because the PERC S100 embedded is not as well supported... (is there a SW raid solution?)

    Thank you

    The H700 is a controller that is supported on the R310, but you must do a clean install or backup/restore.

    The H310 is also supported by the R310.  It is a hardware RAID controller low end and would also require a reinstall/restore.

    The S100 can handle a direct migration of the S300 disc, but when you read, it is not supported in 2012 either.

    You can move the disks to the SATA onboard and get rid of the S300, but there was also a clean installation/restore.  If you did the onboard SATA (in AHCI/no RAID), there was no RAID managed by the system, but you can configure RAID under Windows, which would provide at least some redundancy.  Performance is not worse than the S series controllers.

    My advice?  Never skimp on storage, no matter what it is used for.  Always get the top of the page (H7x0) controller when you configure a server.

  • Satellite U840-113: pilot missing for the PCI Communications controller

    "* Toshiba Satellite U840-113 - PSU4SE: * Win7-Prof - 64-bit with MS-DVD original on off RAID, no RAID oder installed software RAID driver, internal SSD now like normal running, new installed SSD SSD completely new, all the drivers installed successfully - with the exception of the following device: in Device Manager, I find under the"other devices"the position?" Controller PCI-Communications (single) ". *

    Who can help me to locate / find the right driver for this "PCI Communications controller"?

    What ist this? Do I need this?
    The system seems to work perfectly; I disable this feature?

    Thanks a lot for the helpful answers!

    Hello

    This article from Toshiba may be useful:
    http://www.MyToshiba.com.au/support/items/FAQ/222

    The PCI of Simple Communications controller is part of Intel AMT Management Engine Interface and is related to the networking on your computer.

    You will need to install the driver Intel (r) AMT Management Engine Interface.

  • Pavilion G4 w / AMD processor - where can I find a driver for the SM Bus controller?

    Bought a G4 Pavilion - 1164CA and upgraded the HD with SSD

    and did a new install of Windows 7 x 64 Premium.

    The model has a processor AMD A6 - 3400M.

    Device Manager shows that a driver is missing for SM Bus controller.

    I checked the drivers HP page for the model but no chipset or the SM Bus controller driver is...

    http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063&LC=en&cc=us&DLC=en&sw_lang=&product=5148...

    Note: I did a clean install of Windows 7 x 64, not a recovery, read a recovery to a smaller HD would not be possible and also would prefer a clean without all the extras install as the SSD space is limited at first.

    Suggestions to find a driver for SM Bus controller for this model with an AMD processor and chipset?

    Looks like the SM Bus driver is part of the graphics driver.

  • Satellite Pro A200-16N: can I use the recovery CD after upgrade to Vista

    HII!

    IM thinking of upgrading to windows vista on my Satellite Pro A200-16N and I ran the pre-upgrade of windows vista from microsoft website and it says that my system will be in charge of windows vista so im ok about it.

    The problem is that if my laptop was to break or something like that at some point, will my recovery CD provided by toshiba to work always on the laptop with windows vista?
    They will return the laptop for windows xp or from my laptop has another operating system they will not work?

    Also...
    What's the deal with BIOS? : S
    I don't understand!
    If I were to upgrade to windows vista should I upgrade my BIOS before or after the upgrade to vista?
    As I download the new drivers before upgrading Yes?

    Thank you!

    The restore CD will of course work.
    The recovery CD will always set the laptop back to the factory settings. This means that the whole HARD drive will be formatted and the image of Toshiba will be installed.

    > What's the deal with BIOS? I put t understand!
    > If I were to upgrade to windows vista should I upgrade my BIOS before or after the upgrade to vista?
    To my knowledge, that this laptop was already shipped with Vista, so you need not update the BIOS if you want to reinstall Vista.

    Some series Satellite A200 needs a BIOS update if you want to use the XP.
    In such cases, it s advisable to upgrade the BIOS to version XP first, then install OS X.

    Best regards

  • Why can't I download the 9.3 iso upgrade? He always tells me that I am not connected to the Internet and I know that I am.

    Why can't I download the 9.3 iso upgrade? He always tells me that I am not connected to the Internet and I know that I am.

    Apple withdrew temporarily updating iOS 9.3 for devices more old to deal with some issues, what he was creating. Better to wait a few days for them to correct problems.

  • RAM upgrade problem: Flash the BIOS? or upgrade the processor?

    Hi, I jumped in with both feet and now need help to get out me!

    I have a desktop PC HP Pavilion Elite HPE-470uk who becomes a bit slow (processor card here http://ark.intel.com/products/48505/Intel-Core-i3-550-Processor-4M-Cache-3_20-GHz). After you have added a bluray player that I noticed that it's getting a bit slow so thought I would add little RAM.

    I bought a few Hyper X8GB of HyperXbeast 1600hhz, slipped in and the PC did nothing but to turn on and off several times. I checked the two sticks and they both do it. I then (plow in front) checked what memory, the processor can handle and discovered "The Intel® Core™ i3 - 5xx / Intel® Core™ i3-21xx processors handle memory DDR3 1066/1333 MHz" by http://www.intel.com/support/processors/corei3/sb/CS-031175.htm

    After a discussion on another forum, that it has been suggested that I have updated the BIOS because it can allow the processor to manage memory 1600 mhz, but I don't know where to start on this or what version to selected download. I'd appreciate any help you can offer on this.

    The other way, that I can see is to update the processor itself. I thought of nothing too fancy just an i5 because it will allow me to run 3d blurays and should allow me to run some apps at the same time. After reading this http://m.wikihow.com/Upgrade-a-Processor it seems too complicated. Is it really just a matter of taking off the fan, declipsant the old processor, nine droping in and then put on some cooling stick stuff?

    Or should I just return the memory and get good memory?

    See you soon

    Atdot.

    Here are the specifications of original factory for your desktop HP Pavilion Elite HPE-470uk and its card mother MS-7613 (Iona-GL8E). Based on these specifications, this model can support up to 16 GB (4 GB x 4 DIMMs) as follows:

    Dual channel memory architecture
    Four DDR3 DIMM sockets (240 pin)
    PC3-10600 (DDR3-1333)
    PC3-8500 (DDR3-1066)
    Memory non - ECC, unbuffered
    Supports up to 16 GB on 64 bit computers

    In addition, this model can support the following Intel processors;

    Maximum frequency of the processor of the heart < = 2.93GHz
    Intel Core i7 - 8xx (Lynnfield core)
    Intel Core i5 - 7xx (Lynnfield core)
    Intel Core i5 - 6xx (Clarkdale core)
    Intel Core i3 - 5xx (Clarkdale core)

    If you do not have to worry about the update of the BIOS, there is no updates available for your computer BIOS. Honestly, I return the incorrect memory and upgrade to a minimum of 8 GB of RAM. Then, if it solves all your problems, you could also upgrade the processor.

    As the computer is nearly 4 years old, you can consider a factory HP restore to return the computer to a facoty as State. In many cases, it returns original full speed of the computer. The reason why this helps, because the BONE is swollen and clogged over time.

    If you have any other questions, feel free to ask.

    Please click the 'Thumbs Up' white LAURELS to show your appreciation

  • need an exact model of the PCI communications controller driver

    Mr President.

    my model is G62 B39 SE

    WINDOWS 7

    64-BIT

    HARWARE ID IS

    PCI\VEN_8086 & DEV_3B64 & SUBSYS_1439103C & REV_06

    PCI\VEN_8086 & DEV_3B64 & SUBSYS_1439103C

    PCI\VEN_8086 & DEV_3B64 & CC_078000

    PCI\VEN_8086 & DEV_3B64 & CC_0780

    Please I need an accurate model of the PCI communications controller driver

    Hello

    It's a system driver wise called "Intel Management Engine Interface (MEI) ' as mentioned in the following link:

    http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-83746-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5040732 & sw_lang =

    Please download the exe on the link above and install on your machine.

    Kind regards.

  • Satellite Pro A300 - will be lost the warranty if I upgrade the RAM?

    Hey guys,.

    I wanted to know if I purchase and install my own module SO-DIMM RAM in my laptop, it will void my warranty?
    If so, how can I spend my memory?

    I agree with Akuma.
    You will not void the warranty if you upgrade the RAM.
    I've also updated my RAM and I t has not had any problems with my warranty.

    Moreover, the best RAM for upgrade is the RAM even if you as before. I mean the manufacturing and specification. So you can ensure that the new RAM will work.

  • Satellite L30-114 - need driver for the SM bus controller and sound

    Hi, friends

    Please I need your help on my Satellite L30-114. Am having problems with the sound and the SM bus controller, even I downloaded the audio driver and install it, from my camera, sound manager isn't sick, he always tells me my device is not functioning properly? Please I need some help here.

    Secondly, my SM bus controller is sick there the cormer sign please how can I rectify even that my wireless works fine.
    Only the controller sm bus and its giving problems.

    Thank you waiting for your answers.

    Newton

    Hello

    It would be interesting to know what OS you are using.

    By the way: you can find all the drivers here:
    http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  • Freescale in the LabVIEW ARM controller?

    Hi all

    Is it possible to use the freescale MC9S12XEP100RMV controller in the ARMS of LabVIEW?

    Thanks and greetings

    Ben aljia P

    Hi Suren,

    The LabVIEW Embedded Module for ARM Microcontrollers using the "Keil uVision development toolchain to compile, download and debug applications", as this article explains.  (Taken peripheral ARM supported by LabVIEW)

    With this in mind, you should be able to use any microcontroller that supports the "RL-ARM real-time library."  Keil device database lists microcontrollers currently supported with this library.  (RL-ARM real-time library)

    The Freescale MC9S12XEP100RMV MCU is not listed as being supported.  Knowing this, you will not be able to use the LabVIEW Embedded Module for ARM, but you can use the LabVIEW Microprocessor SDK of Module.  The only difference is that the ARM Module has been built on the Module SDK.  The Module SDK is more "generic" and allows to develop support for virtually any 32-bit microcontroller software.

    I hope this helps.

    Kevin S.

    Technical sales engineer

    National Instruments

  • How can I get rid of the toshiba media controller box

    I am playing games whenever I move my mouse this box comes up in the playground which has a picture of a computer. If you click it, it says it's the Toshiba media controller. I got rid of him all the time, but just a new hard drive was put in and back.

    Hello

    ·         What operating system is installed on your computer?

    ·         Is this game online?

    I suggest you follow the steps mentioned below:

    Method 1:

    If it's an online game, I suggest to disable add-ons and see if the problem still occurs, follow these steps:

    a. open Internet Explorer by clicking the Start button, and then click Internet Explorer.

    b. click on tools and then click on Manage Add-ons.

    c. under show, click all add-ons.

    d. click on the add-on to disable and then click on disable.

    e. Repeat step D for each module you want to disable. When you are finished, click Close.

    Method 2:

    Check if the Toshiba media controller is not on the agenda and fonctionnalites features in the affirmative, then uninstall controller Toshiba program and multimedia functionality. Follow the steps described in the following link:

    http://Windows.Microsoft.com/en-us/Windows7/uninstall-or-change-a-program

    http://Windows.Microsoft.com/en-us/Windows7/uninstall-or-change-a-program

    Also take a look at the following link:

    http://us.Toshiba.com/computers/research-center/technology-guides/Toshiba-media-controller-software/

  • The upgrade patch cannot be installed by the Windows Installer service because the program to be upgraded is may be missing, or the upgrade patch may update a different version of the program

    I try to use the Microsoft Office tool that implement an MSI for 64-bit Office 2010 installation file.  The tool works file and creates the msi file.  I get to the tool by going to the x 64-bit folder on the office 2010 installation disc.

    I install a new virtual machine from Windows 7 and tried to use the MSI file to install office 2010 and I get the error:

    "The upgrade patch cannot be installed by the Windows Installer service because the program to be upgraded is may be missing or the upgrade patch may update a different version of the program"

    If I just click Setup on the office 2010 dvd he moved very well on the same VM window7.

    Does anyone have an idea how do to understand why the windows installer keep fails or what he wants?

    If I click on the msi even on a system with office 2007 is installed, I get the same error.

    Thanks for the help

    jbabe

    Windows Update has nothing to do with the upgrade or installation of Office 2010. Please post future questions in this forum: http://social.answers.microsoft.com/Forums/en-US/officeinstall/threads

    ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

  • Error message "the upgrade patch cannot be installed by the Windows Installer service because the program to be upgraded is may be missing or the upgrade patch may update a different version of the program."

    Original title: cannot install WMP11, update rollup 2

    I'm still on WMP 10 for a reason, and I wanted to connect my PC with 360 videos. I downloaded the update, but he told me to go get the Update Rollup 2 or something, so I tried to install it and he told me that I needed to go get the .NET framework 1.1 and .NET framework 1.1 SP1. I went to download them and install them, but he tells me that "the upgrade patch cannot be installed by the Windows Installer service because the program to be upgraded is may be missing or the upgrade patch may update a different version of the program".

    I Googled, tried of all kinds, uninstalled SP3 and tried and nothing.

    Hi xelliotx,
     
    I suggest that you follow these steps.
     
    Step 1:
     
    First of all, download and install .net Framework Cleanup Tool to remove selected versions of the .NET Framework on your computer.
     
    Step 2:
     
    Manually install the versions of Microsoft .NET Framework below:
     
     
    Once this installation is complete, try to install the other required software and check.
     
    See also:
     
    Error message when you install an update for .NET Framework 1.1 or the .NET Framework 1.0: "the upgrade patch cannot be installed by the Windows Installer service.
    http://support.Microsoft.com/kb/940332

    Aziz Nadeem - Microsoft Support

    [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

Maybe you are looking for