The results of the scan saved onecare anywhere?

Similar Questions

• Preview of the scanned image is good but once saved image is black with horizontal lines

  My OS is: OSX 10.9.3

  I have a HP Photosmart Premium series - C309g all-in-one machine. This machine worked well.

  Print is good.

  Copy is good.

  But now I have some analysis of the issues, probably due to an update of the OS.

  Problem: Preview of the scanned image is good, but what saving image--> the image is black with horizontal lines.

  I rumaged through the forums and you have not yet found a solution to my specific machine.

  Any help would be greatly appreciated.

  Thank you!

  Hello

  Scan using the software provided as Capture of Image or preview.

  The application of scanning HP for your printer is not available to 10.9, you use incompatible software.

  Follow these steps to get the results of the analysis required:

  http://support.HP.com/us-en/document/c04028214

  Shlomi

• Accidentally, I saved a PDF file in the cloud and can't be deleted from there. Help, please. I've upgraded to Adobe Acrobat Reader DC and it does not allow me to save the scans on my computer.

  Accidentally, I saved a PDF file in the cloud and can't be deleted from there. Help, please. I've upgraded to Adobe Acrobat Reader DC and it does not allow me to save the scans on my computer.

  Or simply open CD player

  Go to the Home tab then Document Cloud

  Click on the PDF file to be removed

  Click on remove in the top

• Save the Scan OCR HP

  As of today, when I do an analysis of the OCR, I can't program to save him.  The error message is that the scanned document cannot be saved to the specified location.  All the other scan functions work perfectly and the OCR scan worked fine until today.  Help?

  Reload the software, and then try again.

• "The scan of the computer is enabled is no longer" false error

  Hello

  I bought and installed a HP DeskJet 3521. It is configured for wifi connectivity to two computers on our home network. A laptop computer is 8 64-bit Windows. The other is Windows 7 Pro 64 bit.

  The printer seems to work perfectly. However, the driver regularly (as in all the several minutes or so) pops up a message saying "the Scan of the computer is enabled is no longer" or something like that. It is apparent from the system tray. It fades after a few seconds. Otherwise the printer seems to work very well. This happens on two laptops.

  Laptops are in the same room as the printer and the router. The signal strength is high.

  Why did this message occurring and is there a solution for this?

  Thank you

  It is very probably the same problem I had with the HP printers for years.  It happens when the printer goes into a power saving sleep state and falls of connectivity.  To resolve the issue, you have to walk on the printer and the power of the cycle.  It has NOTHING to do with your router or static/dynamic IP allocation.  It's the fault of crappy entiely firmware and HP software.  HP 'experts' are playing the same game of blame-the-other-manufacturer or blame the old user that HP has always played.

  My current HP printer is the third HP sub-standard product I've owned... on three (Yes, I know, shame on me twice).  I've owned a high-end, expensive laptop which overheated during playback of a video to youtube and two printers which disengages automatically when they entered in the mode 'sleep'.  It will be the last HP product I already own...

• Failed to read the scanned text

  scan, but in a text that I can't read. How to change that? It says Rich Text.

  Thanks again for your help.

  However, I still have a problem.  When I see the digitization of documents, it looks like what I put on the scanner, but when I try to recovered, it I can't understand most of the things I see on the scanned document saved.

  I hope I explained the difficulties properly.

  Kind regards

  Dorian

• Office jet Pro 8600: how to change the folder for the scans on my Apple?

  Hi, I want to know how to change the destination for my scans folder when I scan from the printer.  Currently, the scans go to "documents", and I want him to be in a business case.  Clues?  I tried to watch some instructions on the previous posts, but it seems that they are for windows.

  Thanks for the help!

  Hi @jgossc,

  I'd be happy to help you change your scan destination. I understand that when you scan your Officejet Pro 8600 to your Mac, the file analysis is currently underway to your documents and want to let them instead to a business case.

  To change the destination please follow the steps below and let me know the results of your efforts:

  • Open HP utility
  • Select Scan to the computer
  • Click Scan tasks to change
  • Choose a shortcut to scan
  • Select Edition
  • In the options listed here, you should see scan destination

  If this resolves the issue, please click Accept as Solution button below; If not, let me know and I will do everything I can to help. Thank you.

• HP Envy 7640: Unable to set the scanning resolution

  Have been unable to set the resolution of scan during the scanning of the glass in a computer file (pdf, jpg). Guide the user to the HP page 47 7640 said: "● If you want to adjust the size of the scan, output type, scan resolution, or file type and so on, start scan from the software of the printer."
  ● To avoid all scanned text wrong or missing, make sure that the brightness is set properly the
  software.
  ● If you want to scan a document with several pages in a single file instead of several files, run it
  Scanner with the software of the printer instead of the sweep of the screen of the printer".

  First of all, where is the "printer software" to start the scan?

  Have tried all this. When I opened the series HP Envy 7640 (network): Assistant of HP printer, I click on "Scan the Document or Photo a" place in the scanning area. No scan dialog box never opens. Actually I tried to reinstall the printer driver. No change. Always impossible to get a scan dialog box. In addition, when I go in the start menu and the title of the series 7600 HP: HP envy, I click on the HP Scan icon. After a long wait, a dialog box appears that says: "Cannot communicate with Scanner", and it offers a few options. The first is to activate the device (printer), and then on; the second, control cables (its wireless operation); the third: try the software "fix." Happy to report that after stopping then on and running assistant printer again, this time by pressing the "scan a Photo Document' results in the appearance of a dialog box to make the changes that I've been looking for.

• OfficeJet 5615 black stripes during the scan

  My Officejet 5615 works perfectly, but in recent months, it shows black scratches on document scanned on the glass. Bands go for the length of the scanned page, and the glass is clean. I guess there is something wrong with the 'pixels/conduit' scanners. You are looking at him directly when it works I do not see the strange light differences between all the lights/pixels. Would it be the internal scanning module simply dirty on some lights? How can I disassemble the glass and have access to a scanner directly so I could clean it up? Thank you

  Hi eferrari,

  I see you have found black bands when scanning.
  I'll be happy to help you.

  I checked the manual and it does not provide how to remove the glass from the printer, unfortunately.

  Series of all-in-one HP Officejet 5600 User Guide.

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector)

  Problem number one causing lines in the analyses.

  I have provided a document through the steps to see if it will solve this problem.

  Vertical stripes, lines or streaks on Copies, faxes or scans.

  Do you get the lines when you perform a copy?

  Try the ADF and glass to see the results.

  I met this document for How to clean the Scanner glass. The document is good for different models.

  Since there is no documentation for your printer probably, it is not recommended.

  Use your own descreation. It might help you understand how to remove the glass to clean it.

  If it has not the tab then it is probably sealed in it.

  Personally, if it were me I wouldn't remove my printer.

  You might want to consider appeal to HP, they may be able to offer you a discount on a newer model. Contact HP worldwide.

  Thanks for posting on the HP Forums.
  Have a great day.

• How to synchronize the start of IT and relaxation the Scan list (DAQmx Switch)

  Hello

  I want to measure samples of N to the AI0 of Council NI PXI 4461. The measurement starts on a rising edge of a digital triggering provided to the PFI0 of the same Board. The measure is configured with samples of N/2 pretrigged. So far, everything is under control...

  Using an NI PXI 2567 Board, the signal applied at the entrance the 4461 (AI0) switches between a V2 and V1 signal. I would like to synchronize the switch between the two signals with the trigger signal applied to the input of the PFI0 Governing Council 4461. In order to obtain samples of N/2 of V1 and V2 samples N/2. Synchronization of 1 to 5 ms would suffice!

  My question is how to synchronize the start of acquisition of AI pretrigged of 4461 with the switch control given by the Council of 2567?

  Thank you in advance for your help...

  PS: the configuration of the system is:

  -LabView 8.5

  -Chassis PXI-1044

  PXI-4461 on slot 2

  Module 4-slot PXI-2567

  Hi Frederic,.

  I came back to this recently and used the following examples to run the desired synchronization.

  PXI-4461: Acq & graph tension-Int Clk - dig Start & Ref .vi

  Samples per channel = 1000

  Rate (Hz) = 10000.00

  Start the trigger Source = / [name of the instrument DAQmx] / PXI_Trig0

  Onboard start = fall

  Reference Source Trigger = DAQmx Device Name] / PXI_Trig0

  Reference edge = fall

  Trigger samples = Variable (100, 500, 900)

  PXI-2567: Switch Scaning-SW Trigger.vi

  Advance the output terminal full = / [name of the instrument DAQmx] / PXI_Trig0

  Scan list = / [name of the instrument DAQmx] / ch0-> com0.

  Scan list = / [name of the instrument DAQmx] / ch1-> com1;

  Hardware configuration:

  The PXI-2567 module controls an external relay that switches between the voltage of 5 V on ch0 and ch1 0 V.

  The PXI-4461 connects to the COM of the external relay and therefore reads 5V when ch0 is connected; 0 v when ch1 is connected.

  Procedure: The above examples are used in the following procedure.

  1. run the PXI-4461 VI.  A start trigger (falling edge) is necessary to start collecting samples before firing.

  2. launch the module, PXI - 2567 VI.  When ch0 is initially (and immediately) on com0, a trigger is sent to PXI_Trig0.  The PXI-4461 will begin to acquire samples before firing.

  3. - click on the "Connect to the next" button on the front of the PXI - 2567 VI module.  This sends a trigger to entry software for the PXI-2567 module and the transitions of the scan for ch1-> com1 list.  Once the PXI-2567 module remains (debounced), advanced complete relaxation is sent on PXI_Trig0 for the PXI-4461.  The PXI-4461 will begin to acquire samples after outbreak.

  Note: Instead of the trigger of the software entry, an external input trigger can be used (e.g. PXI_Trig1).

  Results:

  > Before instant release of samples = 100

  Delay is caused by the time of actuation of external relay.

  

  > Before instant release of samples = 500

  Delay is caused by the time of actuation of external relay.

  

  > Before instant release of samples = 900

  Delay is caused by the time of actuation of external relay.

  

  I hope that the attached screws and the explanation above helps you and/or other customers who have this problem.

  Best regards

  Chad Erickson

  Switch Product Support Engineer

  NOR - USA

• Photosmart 7515 adds lines from bottom of the scanned image

  My photosmart 7515 started just add a line double about 2 inches from the left edge of all of the scanned images. NO modification of the system that I am aware. Prins computer or internet as usual. Any ideas?

  Hi Bobvan1,

  Welcome to the Forums of HP Support! I see when you scan with your HP Photosmart 7515 he started to add a double line about 2 inches from the left edge.

  I would like that you start here: vertical, lines or streaks in the Copies or Scans, please fill ALL troubleshooting steps, focusing on cleaning.

  Let me know the results, I'll watch for your reply.

  Thank you

• The scan to PC on 5525 has stopped working!

  Hello!

  I am using 8.1 Windows 64 bit. I have not had any problems until a few weeks earlier. After a Windows Tuesday update, the scan function became unusable. The client PC says that it cannot communicate with the printer. The printer says canoe show the PC. It used to work perfectly, I used quite often scanning.

  I tried to reinstall the driver, no luck. Tried to use HP doctor or what and he says he can not solve the problem and I have to contact support.

  However I do know that Microsoft screwed up something like the Networkcommunicator.exe runs in the background at least pending 10.

  Also my neighbor just bought a printer totally even, and he has Win7 64 bit. He has downloaded the latest driver and installed and quess what - everything works perfectly ECXEPT scanning to PC.

  I use the Wi - Fi mode, printer's IP, it may be possible, it can print and it is visible on the network even through hpeprint.com

  It must be wound to MS and HP as several types of windows are affacted.

  Please provide a fix as soon as possible.

  Affected OS:

  8.1 Windows 64-bit

  Windows 7 64 bit

  Thank you

  Circuit breaker

  Hello Breaker,

  I noticed your post on the "scan to computer" no longer works correctly after a Windows Update. I realized when I tried to reinstall the driver and software it has failed and the HP print and Scan Doctor could not solve the problem. I have seen that the printer can be crazy however, so that shows that it is on the network.

  I would like you to open this guide (choose your OS) and scroll to the bottom for "eight step: disable the services and startup programs" and start from there you have tried the steps in the guide. I hope that these measures will help! Use the guide on both computers.

  The printer is not found during a wireless network Installation

   

  Let me know the results!
  

  Have a great Tuesday

• OfficeJet 8600 more: impossible to activate the Scan

  Use OS x 10.10 and printing/scanning using wifi, all of a sudden the scan button went from my printer on my macbook pro. It worked fine until a few days ago. I tried to delete the printer drivers and reinstall. I chose the name of the printer and printing not slected to air. I checked all of the updates and also updated the firmware to the printer. The scan button is missing and the option "enable scan" is crossed out in red. If I connect the printer cable printer a new printer icon becomes available in the primnter options and it can analyze. Any help would be appreciated.

  Hi @PlusBiz ,

  I see that you have problems with scanning via the wireless network, but you can scan through the USB connection.
  I want to help you with this issue today.

  Fix permissions of the drive on the Mac:

  Close all applications.

  In the Apple menu, click OK, click Applications, and then click utilities.

  Double-click disk utility.

  Highlight your hard drive / partition on the left.

  Click on check and then repair disk permissions.

  Restart the computer...

  Reset the printing system:

  Note: This will remove all printers in the print and Fax/Scan, any printer deleted can be re-added later by clicking the sign plus (+) symbol.

  Click on the Apple icon and then click on System Preferences.

  Click on Printers & Scanners.

  Make a right click (or Ctrl + click) in the left white side panel, and then click Reset printing system.

  Click OK to confirm the reset.

  Type the name and the correct password.

  Click OK to reset the printing system.

  Then click on the sign to add the driver, highlight the printer +. (you may need to click the drop down menu to select the name of the printer) Then click the Add button.

  Attempt to activate the scan of the computer again.

  Try to print and scan the image.

  If you do not always have the option, do a uninstall complete and reinstall the software.

  Uninstalling the printer software.

  The steps should also work for Yosemite.

  Also, check the following points:

  Some of the files described in the following steps can be found, if you can't find one of the files or folders on your computer, do not be alarmed.

  Move the files or folders to the Recycle Bin, drag and drop.

  • Macintosh HD/Applications / /Hewlett-Packard folder
  • Macintosh HD/Library/Application Support /- delete all files and folders on HP/Hewlett Packard
  • In Macintosh HD/Library/Caches - delete all files and folders on HP/Hewlett Packard
  • Macintosh HD/Library/Documentation/Help /- delete all files and folders on HP/Hewlett Packard
  • MacintoshHD/Library/Frameworks/HPServicesInterface.framework
  • MacintoshHD/Library/Frameworks/HPSmartX.framework
  • Macintosh HD/Library/Image Capture / TWAIN Data Sources /HP Scan Pro
  • In Macintosh HD/Library/Image Capture/Scripts - delete all files and folders on HP/Hewlett Packard
  • In Macintosh HD/Library/Preferences - delete all files and folders on HP/Hewlett Packard

  Move the Macintoshloginwindow.plist on the desktop. NOTE: Does not delete the loginwindow.plist file during the manual uninstallation may cause uninstall be retained.

  • In Macintosh HD/library/printers/hp - delete the folder
  • In Macintosh HD/Library/StartupItems, drag the following files in the trash, IO HP and HP trap monitor
  • In Macintosh HD/users/username (this should have a symbol of a house next to him) / Library/Preferences, drag the following files to the Trash: * all files starting with com.apple.print, * all files starting with com.hp, * all files beginning with Hewlett-Packard, * files starting with HP or hp
  • In MacintoshHD/users/USERNAME/Library/printers, drag all all-in-one printers listed here in the trash.
  • Drag the icons of HP from the dock and drop it onto a blank space on the desktop. The icon will disappear.

  Close all open windows.
  Turn it back on.
  Empty the trash.

  Reinstall the software of the printer again. HP Officejet Pro 8600 series full feature software and drivers.

  If you're still having problems, it could have been an automatic update on the router and port scan isn't currently open.

  You can contact the router company to verify and to open these ports 9220/9500/427 on the router.

  Please let me know the results.

  Have a wonderful day!
  Thank you.

• Menu has changed, the scans disappeared... need help!

  Since this morning, something changed with my ability to access to the & use my scanner on my printer function. I have the series of J611 3050 has and used the night to print and scan last and everything works great. But when I tried to analyze something earlier, nothing is beautiful.

  It used to be (not later than last night) when I clicked on the icon for HP desket a menu would open enabled me to choose what I wanted to accomplish. Now, when I click on this icon is "printer assistant" for which nothing happens when I click it I don't see, 'See what's printing' "set preferences" and 'customize your printer', which none have no bearing on this issue that I can find.

  It used to be (not later than yesterday) that when I scanned it something a window open which allowed me to make a few changes to analysis before you save it.  It was all the scans have been automatically saved in a specific file of my choice. This window opens now is no longer, and sweeping turns to in limbo where I can't find it.

  Can someone PLEASE help me understand what happened and how do I go back to the way things were?

  Thanks in advance!

  Remy

  The solution I found to this problem is to uninstall the printer and reinstall using the latest drivers. HP released a new package of drivers for this printer and all printers that use a similar software, which corrects this problem.

  HP Deskjet full feature software and drivers

• LaserJet M5035 MFP: I have a purple line which appears in the scanned document

  Hello

  When sending e-mail through the printer scanner, I have a purple line which appears in the scanned document. Scanning is done from the "feeder ' ' the printer and not the glass.

  The windows were all cleaned.

  I did the test and digital printing of the "feeder ' ' and I have no lines for printing!   I did update the firmware of the printer and I still have the same result.

  You have a solution to this problem?

  Thank you

  

  The small windows of the charger scanner had a small red above mark.  When the analysis has been done and sent on an e-mail, the line shows as it is scanned were made with the color scan option.  If I print the line doesn't show because the printer is not color!