The router access point wireless bridge

Similar Questions

• How can I reset or fix my router wireless or (lost the ability to connect wirelessly to the internet) access point

  Wireless hub works, other computers are connected

  On a laptop, I lost the ability to connect wirelessly to the internet (message: limited connectivity)

  Recommended by the system solution: reset or repair your access point or wireless router

  How can I do?

  I think that what you aim for is "power cycle".

  To do this, simply unplug the router/access point power adapter. Wait a minute. Then reconnect it.

  Hope this helps

  Post back if necessary

  ___________________

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Add WRT54G: second router / access point, unable to get to the outside network.

  Here is the prob:

  We just got cable internet the other day and the cable operator insisted on using their v1000 Belkin F5D7234-4 instead of my WRT54G V8. So I thought I'd use the WRT54G as a second router/AP (without wireless/LAN/WAN). I was eager to do this by running an ethernet in the WAN on the WRT54G port and plug it into the port of the client on the Belkin, place the wrt - 54 G at the other end of the House and have the WRT54G broadcasting the same SSID and require authentication even as the Belkin and use the Belkin to Linksys Wireless Bridge. In this way, it will extend my wireless network and all computers can access the internet and the other (wireline customers will keep at wire-speed, wireless is not authicate to two different networks.)

  I can't get the Linksys network based able to see all the other computers outside the WRT - 54 G, even for wireless clients. On the side of things Belkin network, I can't ping the router even if she pulls a DHCP in the Belkin address. All customers the Belkin side can meet and thin internet. I've fiddled with the WRT54-g for almost an entire weekend now with no result. The WRT54G can see the other router as a DNS as well as external DNS providers, but none of the client computers can. Basically, I'm wanting to extend the network of Belkin 4 as most cable customers and fill a few dead wireless, and make the visible computer on the same network of suggestions?

  Parameters of WRT - 54G:

  Automatic configuration - DHCP

  Same domain name like Belkin
  IP router set a tire to the DHCP server

  DHCPserver OFF

  Mode of operation: router

  Safe are disabled.

  Wireless SSID is the same as Belkin

  Wireless channel is the same as belkin.

  Method and auth. key is the same as belkin.

  Belkin:

  DHCP is on.

  15 IP addresses available.

  Wireless gateway is on with the WRT54G Wireless MAC address information.

  Ethernet cords are connected.

  I played with static routes for hours, tried the option routing dynamic, even tried DMZing of the WRT54G intellectual property in the belkin and still unable to connect to the internet. Tried the Belkin MAC address cloning. Nothing seems to work. When I plug the WRT - 54G directly in my digital/Modem/phone cable box, I get internet and everything. I'm at the point of throwing same DD - WRT on it.

  But beyond connection "wireless" I discovered really does not work if well (drops random wireless speeds seize up) with two different pieces of equipment running two different firmwares. So the thing connecting wireless set was out the window.

  I however knew what I had to do Linksys firmware:

  1.) DHCP clients forward.

  Customers of Belkin - network

  Linksys customers - network B

  The dhcp pool was not get transferred to the client computers. That is the 1-2 on network computer had XXX. XXX.100 - 102 for 3-4 computers on network B was YYY. YYY. YYY statically set by Windows. Even after changing to a static address on the network A dhcp scope I could still connect to the internet or to one of the computers on the network.

  The static routing table seemed not lead me anywhere either, and I've tried dozens of configurations.

  The way I got it Setup is with the customer enthernet of the Belkin ROUTER to THE Internet on the Linksys WRT54G port 1-4. Maybe I should have plugged the ethernet on the client side of 4 ports Linksys?

  Anyway DD - WRT redirect DCHP feature was what I need.

  Regarding the scenario wireless two routers have the same encryption method and key but different channels and ssid. Who, with DD - WRT for some reason when I jump on the wireless-B, Vista will be ID it as network A (B).

  I hope that it has not violated anything except the guarantee which was anyway. The reason for which I needed for my network up this way is because I do a lot of work using VM (of various operating systems), is simply easier to have two separate semi networks. (to different physical locations in the House)

• Print Epson printer States: a router/access point channel conflict detected - improve your wireless network environment?

  I try to print from my laptop on my Epson printer.  It will not work on any of the documents or the internet.  The Epson prints what follows: a conflict of channel router/access point - improve your wireless network environment, has been detected.  My router is sitting next to my printer and the laptop.  The Green WiFi light on the front of the printer is on.  I have no problem using my Ipad in the other room.  So does mean printing?

  It's that all the documents, both new & saved and the same Wordpad?

  Maybe

  http://support.Epson.ru/products/manuals/102044/Panel/g_html/external/manual_e01.htm

• 4402 wireless controller and the 1130AG access points

  I have a bunch of 1130AG (35) and 1231 points of access. I just bought a controller 4402 so I could handle these much easier access points. I currently have the offline access points, so I could control. With the wireless in the mix controller, that I have to fix these to light mode or can I leave them offline.

  We know not the operating instructions so I can leave them in stand-alone mode. Most of them is in the rafters in our warehuse, and I didn't have to pull of these if I have to. If I can use them offline, how can I do that?

  Thanks much for any info!

  Dave

  Hi Dave,.

  A WLC manages autonomous APs.
  So if you want to centralize the management of your APs through the WLC, you will need to convert it to light and enter them on the WLC.

  To convert the lightweight access points, you can choose between several options:

  1. thanks to a specific upgrade tool that you could install on a PC:
  http://www.Cisco.com/en/us/partner/docs/wireless/access_point/conversion/LWAPP/upgrade/guide/lwapnote.html

  2. [the most evolutionary] by WCS, with a model of migration that could apply to several APs:
  http://www.Cisco.com/en/us/docs/wireless/WCS/7.0/Configuration/Guide/7_0apcfg.html#wp1054876

  3. [not in any book] by the following steps:
  3 (a) download the CEC lwapp recovery image and store it on a TFTP server.
  3 (b) Telnet to the stand-alone PA and issuing the following command:
  Archive Download-sw / overwrite/reload tftp: / // [lwapp recovery image file path]

  As a general recommendation, before to convert the lightweight access points, you can be sure that the wired infrastructure behind is ready to direct them to the WLC for recording.
  It's suggestions explained in the link on the above option #1.

  Hope this helps,

  Fede

  --
  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Windows 7 wireless emphasizes the connection to the wrong access point

  I use a model of wireless USB Netgear WN111 with Windows 7 64-bit adapter, connect to a D-Link wireless access point.

  Every time I have connect or wake the computer from sleep, he insists on connecting to the wrong access point - it connects to an unsecured Linksys device somewhere within the range.  I then manually connect to the correct access point - my D-Link.

  I went into the network sharing Center > manage the wireless networks and removed the network Linksys of rogue, but it always comes back.

  Any ideas or advice?

  Hello

  I don't know why he keeps picking up the 'rogue' network after that you deleted. My Windows 7 does not behave like that, and my research can reveal a way that I could do. Maybe someone else can tell you why he does. However, as a solution, you can try the following in manage wireless networks...

  1. do not remove the network of thugs, move it to the bottom of the list all the way down.

  2. open the rogue network properties and uncheck the box "connect automatically when this network is in range.

  3. open the properties of your network and check the box "connect automatically when this network is in range.

  4. you can even try to untick "connect to a more preferred network if available" both networks.

  Please mark this as useful or response if applicable.

  Tricky

• Ordered the wrong access point!

  I thought that I had ordered a 1130ag but looks like I ordered a 1131ag LWWAP.

  Please could someone tell me what the difference between a 1130 and 1131. I understand I can load the IOS on the light AP software using a tftp server, but I do not know which exit to load on this subject. 12.3JX, 12.3JA, 12.3JEA, 12.3JEB! can anyone help please? either by the way, I am in the United Kingdom, do not know if this affects image to install. Thank you.

  Hi Paul,.

  This happens all the time, so it shouldn't be a problem :) I'm guessing that you have received this AP - AIR - LAP1131AG - x - K9 LWAPP. When you really wanted this AP - AIR-AP1131G-x-K9 Cisco IOS software. Look at the comparison;

  http://www.Cisco.com/en/us/products/ps6087/products_data_sheet0900aecd801b901c.html

  That being said, you should be good to go with 12.3 (11) JA1.

  To access Cisco Aironet to Cisco IOS version 12.3 Points (11) JA1

  http://www.Cisco.com/en/us/docs/wireless/access_point/iOS/release/notes/b11jar1n.html

  Cisco IOS version 12.3 (11) JA1 supports 32 MB independent platforms. 16 MB platforms and platforms supported by Cisco IOS version 12.3 (8) JA and earlier versions (350, 1100, 1130, 1200 and 1230 access points and access point/bridge 1300 series) are supported by Cisco IOS version 12.3 (8) JEA1.

  Do not install a "JX" (it is a software image support to upgrade and recovery Cisco Lightweight Access Point Protocol (LWAPP));

  These release notes describe features, improvements, and caveats for Cisco IOS release 12.3 (11) JX1.

  Note: This version must be loaded on points of access to the plant or by using the lightweight stand-alone mode upgrade tool. Your access point may become unusable if you install this software without using the upgrade tool.

  http://www.Cisco.com/en/us/docs/wireless/access_point/iOS/release/notes/b311jx1.html

  Returning to standalone Access Point

  http://www.Cisco.com/en/us/products/HW/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272

  You can convert an access point of the mode light return to autonomous mode by loading a Cisco IOS version that supports stand-alone mode (Cisco IOS release 12.3 (7) JA or earlier version). If the access point is associated with a controller, you can use the controller to load the version of Cisco IOS. If the access point is not associated with a controller, you can load the version of Cisco IOS using TFTP.

  By using a TFTP server to revert to a previous version

  Follow these steps to return mode LWAPP stand-alone mode by loading a version of Cisco IOS using a TFTP server:

  --------------------------------------------------------------------------------

  Step 1 the IP address of the computer on which the server software runs TFTP should range from 10.0.0.2 to 10.0.0.30.

  Step 2 make sure the PC contains the file access point (for example, c1200-k9w7 - tar.122 - 15.JA.tar for a 1200 Series access point) in the TFTP server folder and the TFTP server is activated.

  Step 3 Rename the access point image file in the folder of the TFTP server c1200-k9w7 - tar.default for a series of 1200 point, c1130-k9w7 - tar.default of access for a series of 1130 access point and c1240-k9w7 - tar.default for a series of 1240 access point.

  Step 4 connect the PC to the access point using an Ethernet category 5 cable (CAT5).

  Step 5 disconnect the power to the access point.

  Step 6 push the MODE button and hold the button while you reconnect power to the access point.

  Step 7 hold the MODE button until the status of the LED turns red (approximately 20 to 30 seconds), then release.

  Step 8 wait until restarting access point, as indicated by the LEDs become green followed the status LED flashes green.

  Step 9 after the access point reboots, reconfigure using the GUI or the CLI.

  This doc.

  http://www.Cisco.com/en/us/products/HW/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272

  I hope this helps!

  Rob

• Using the E2000 as a wireless bridge

  After informed that I can not use the AP I bought yesterday as a bridge, I decided to get an another linksys E2000, as the guy in the shop told me that I can throw in for sure bridge mode.

  Now, like I do for the first time, and my English isn't the best, I was not able to find some instructions, or better yet a step by step guide that can help me. I searched the Forum, but I can't find anything on the E2000 in Bridge mode. LIKE I said that my English is not the best, if anyone can help me? If anyone can find instructions step by step would be great. It is not a problem if it is in English, there are a few pictures. I hope that I can finally use the WLAN today...

  The WET610N is a wireless bridge. It should work. I don't have that so I can't say if it's good or not.

• Configure the router Cisco E2000 wireless for my laptop HP with Vista, I can't work.

  Configure the router Cisco E2000 wireless for my laptop HP with Vista, I can't work.  I spoke with Cisco and they said that my Atheros AR5007 adapter does not work with Cisco E2000 and contact my computer vendor

  Hello

  HM... I guess that the Cisco people know what they're taking everything. The AR5005 is a b/g card and there should be a good reason to not work with a router that is able (the E2000 is able g) g.

  This is HP drivers for the card, http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?cc=us&lc=en&dlc=en&softwareitem=ob-55737-1

  If you can't make it work, you must decide between a new card or another router.

  Personally, if it's new and I could return it, I'd get a different router model. But YMMV

  ------------

  My posts reflect my understanding and experience. It does not necessarily reflect the opinion or the vision of Microsoft, or anyone else.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Windows 7 PCs are not connected to the closest access point

  Windows 7 PCs are not connected to the nearest access point.  Any ideas?

  For example:

  We have AP 1 and 2 of the AP for exaple.  They have the same SSID.  AP 2 is further with a bad signal.  AP 1 is closest with an excellent signal.  Why my laptop does not connect to the AP 1?

  You MUST use the same SSID.  I think that you misread my post.

  And Yes, a channel problem is that what I have proposed.  You can try to configure access points using the 3 discrete channels (1, 6 and 11) to minimize any overlapping units to the same channel coverage.
  At least this is the traditional way, we do it, although the automatic selection increases common and 11n 40 Mhz channels (if defined in this way) are also in.

• The question of the Access Point wireless router

  I am considered to be an amateur when there are routers so patient with me. I have a wireless router in my office and two workstations are hardlined (ethernet cable-joint) to the router. Then, in the living room, I have 3 devices (Xbox, BlueRay, directTV) I want on the network. Rather than running three office ethernet cables, I expect to have some sort of (reverse hotspot) where a device could hop on the wireless router and the signal I inflexible at these three devices. Not sure if this would require an Access Point or another wireless router?

  Any thoughts would be appreciated.

  -J

  I suggest that you try to find something on WET54GS5... is a bridge with 5 ports wireless if I'm not mistaken... but since it's under Cisco Small Business, I suggest you could ask more about it here

  Cisco Small Business support community

  Or you can see WET54G and buy a separate so you switch can accommodate other devices
  

• Subnet routed on the main gateway of the WiFi Access Point

  Hello people.

  I have the wireless router WAG200G. It sports a RJ-11 input and a four port RJ-45, while it is compatible 802.11 g.

  I need to use it as an Access Point, WiFi via DHCP clients accommodation in its own range (I fear not the 192.168.1.x default range). However, I need to give this subnet, access the internet via my main network which has another Beach, say 10.0.0.x, where the entry door is 10.0.0.2

  I tried the subnet routing WiFi to my front door, but apparently I'm missing something I ever managed :-)

  For those wishing to help could you please tell me through this page http://ui.linksys.com/files/WAG200G/1.00.09/Setup_routing.htm ?

  FYI, I got the Linksys in my network off main application everywhere (Linksys & PCs) static IP, nat and affecting encapsulation Bridged Mode only. That's how it worked, but for security reasons, I need to isolate this subnet WiFi.

  Any kind of help would be appreciated.

  If you used the WAG as point of access only with standard Linksys firmware, then you cannot use the DHCP server. The WAG will always assign its own IP address as the gateway via the DHCP server. The only option would be to use the DHCP relay function or set another DHCP server.

  As long as the WAG is connected through a LAN port to your existing network you connected side full LAN of the WAG in your network. You don't want to run any DHCP server on the WAG. Your main router provide DHCP service. If your wireless devices have trouble getting an IP address from your main router, which should be the first thing to solve...

• [Wireless-Vista] Disable the automatic access point.

  Right then, I had this problem when you play any kind of online game, what microsoft calls a 'feature', when I play a game online, I get a 5seconds or until disconnecting lag spikes every 1-5 minutes, making it impossible to play counter-strike, Call of Duty Modern Warfare 2, Battlefield 2 and all these sorts of FPS games. I read on this vista of "paintings" Wi - Fi point automatic scan has, so I tried with impatience to deactivate, without success, I even once turned off automatic TCP/IP that crashed my computer, so now I'm wondering, how in the world am I supposed to play a game with spikes of major shift due to a malfunction of the so-called?
  If there is a way to turn it off, remove, or simply work around, tell me. I don't care if it is not allowed, because I got it with feautures of microsoft...

  sckizman,
  Have you ever been able to play games online with this computer?
  What version of Vista and what service pack you have?
  You are able to surf on the net normally or you we lag with almost anything on the internet?
  If you have not yet done so, perform a clean boot , and then test your access.  Also make sure that your system BIOS and chipset drivers are up to date.

  Here are instructions on disabling automatic switching between wireless access points:

  Prevent your computer from switching between wireless access points

  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Cannot access Internet even if the router USB adapter Wireless G made the connection and

  Hello, I recently bought a Wireless-G USB Network Adapter with SpeedBooster model WUSB54GSC to go with my Wireless-G Broadband Router model WRT54G2 and I can't access the internet.  The laptop tells me I am connected and that force is Excellent, but when I open my browser, I can't access any site at all. When I try to add the laptop to my network magic on my computer, it tells me that it cannot connect with the laptop.  My Nintendo Wii and Itouch work perfectly with the router so I think it's my browser settings, but I can't understand it.  Thank you!

  Hey, thanks for trying to help out.  It turns out that my firewall did not allow the laptop to access the internet.  I made a few adjustments on my firewall settings and it all worked out great.

• WET11 V2 cannot be connected to the AP (access point) via WiFi

  I am facing following problem.

  Someone at - he advice me please how to solve these problems.

  Purpose:

  1. I want to use internet on TV Sony Bravia. (Bravia has no WiFI. "I have only LAN).

  Environment:

  1 access point (Router) - WiFi > WET11 V2 - LAN > TV (Sony Bravia).

  2. IP address 192.168.1.5 = WET11 (automatically not static)

  BOF WET11 V2 assigned IP address access point.
  I checked the access point access point IP attributed to WET11.

  3 TV IP address is automatically.

  But the IP address is unaffected for television.

  4 WET11 firmware version = V2.05 (Sep 16, 2003)

  Problem:

  1. IP address cannot be assigned for television.

  2 WET11 is not the answer for the command 'ping 192.168.1.5' WiFi access point.

  3. I did ping command when the LAN TV cable has been replaced by the wireless access point LAN cable.

  BR

  Mutt

  It is not advisable to use a 802. 11B wireless bridge on a device such as your streaming media TV. Connection will be very slow and is probably the reason why you have a hard time to connect to your wireless router that's more compatible with it. I suggest using a Wireless N bridge or a multimedia wireless on your TV adapter so that you can fully appreciate the media streaming.